| Message ID | 20240523231516.545085-9-jm@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Enable eQEP DT support for Sitara K3 platforms | expand |
On 18:15-20240523, Judith Mendez wrote: > TI K3 SoC's support eQEP hardware, so enable TI eQEP driver > to be built as a module. All the nodes seem to be only in disabled mode, is there even a single board that is actually using this? if so, why isn't it enabled? > > Signed-off-by: Judith Mendez <jm@ti.com> > --- > Changes since v1: > - No change > --- > arch/arm64/configs/defconfig | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig > index 2c30d617e1802..23d11a1b20195 100644 > --- a/arch/arm64/configs/defconfig > +++ b/arch/arm64/configs/defconfig > @@ -1593,6 +1593,7 @@ CONFIG_INTERCONNECT_QCOM_SM8550=y > CONFIG_INTERCONNECT_QCOM_SM8650=y > CONFIG_INTERCONNECT_QCOM_X1E80100=y > CONFIG_COUNTER=m > +CONFIG_TI_EQEP=m > CONFIG_RZ_MTU3_CNT=m > CONFIG_HTE=y > CONFIG_HTE_TEGRA194=y > -- > 2.45.1 >
Hi Nishanth, On 5/24/24 12:59 AM, Nishanth Menon wrote: > On 18:15-20240523, Judith Mendez wrote: >> TI K3 SoC's support eQEP hardware, so enable TI eQEP driver >> to be built as a module. > > All the nodes seem to be only in disabled mode, is there even a single > board that is actually using this? if so, why isn't it enabled? I will add pinmux and enable in the board level dts file. ~ Judith > >> >> Signed-off-by: Judith Mendez <jm@ti.com> >> --- >> Changes since v1: >> - No change >> --- >> arch/arm64/configs/defconfig | 1 + >> 1 file changed, 1 insertion(+) >> >> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig >> index 2c30d617e1802..23d11a1b20195 100644 >> --- a/arch/arm64/configs/defconfig >> +++ b/arch/arm64/configs/defconfig >> @@ -1593,6 +1593,7 @@ CONFIG_INTERCONNECT_QCOM_SM8550=y >> CONFIG_INTERCONNECT_QCOM_SM8650=y >> CONFIG_INTERCONNECT_QCOM_X1E80100=y >> CONFIG_COUNTER=m >> +CONFIG_TI_EQEP=m >> CONFIG_RZ_MTU3_CNT=m >> CONFIG_HTE=y >> CONFIG_HTE_TEGRA194=y >> -- >> 2.45.1 >> >
Hi Nishanth, On 5/24/24 9:13 AM, Judith Mendez wrote: > Hi Nishanth, > > On 5/24/24 12:59 AM, Nishanth Menon wrote: >> On 18:15-20240523, Judith Mendez wrote: >>> TI K3 SoC's support eQEP hardware, so enable TI eQEP driver >>> to be built as a module. >> >> All the nodes seem to be only in disabled mode, is there even a single >> board that is actually using this? if so, why isn't it enabled? > > I will add pinmux and enable in the board level dts file. Question about the above... If I enable eQEP at the board level, there will be pinmux conflicts. So, I could: 1. Leave eQEP disabled 2. Enable eQEP and disable main_uart1 at the board level dts file 3. Enable eQEP in an overlay and also disable main_uart1 Let me know which option works for you. ~ Judith > >> >>> >>> Signed-off-by: Judith Mendez <jm@ti.com> >>> --- >>> Changes since v1: >>> - No change >>> --- >>> arch/arm64/configs/defconfig | 1 + >>> 1 file changed, 1 insertion(+) >>> >>> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig >>> index 2c30d617e1802..23d11a1b20195 100644 >>> --- a/arch/arm64/configs/defconfig >>> +++ b/arch/arm64/configs/defconfig >>> @@ -1593,6 +1593,7 @@ CONFIG_INTERCONNECT_QCOM_SM8550=y >>> CONFIG_INTERCONNECT_QCOM_SM8650=y >>> CONFIG_INTERCONNECT_QCOM_X1E80100=y >>> CONFIG_COUNTER=m >>> +CONFIG_TI_EQEP=m >>> CONFIG_RZ_MTU3_CNT=m >>> CONFIG_HTE=y >>> CONFIG_HTE_TEGRA194=y >>> -- >>> 2.45.1 >>> >> > >
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 2c30d617e1802..23d11a1b20195 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -1593,6 +1593,7 @@ CONFIG_INTERCONNECT_QCOM_SM8550=y CONFIG_INTERCONNECT_QCOM_SM8650=y CONFIG_INTERCONNECT_QCOM_X1E80100=y CONFIG_COUNTER=m +CONFIG_TI_EQEP=m CONFIG_RZ_MTU3_CNT=m CONFIG_HTE=y CONFIG_HTE_TEGRA194=y
TI K3 SoC's support eQEP hardware, so enable TI eQEP driver to be built as a module. Signed-off-by: Judith Mendez <jm@ti.com> --- Changes since v1: - No change --- arch/arm64/configs/defconfig | 1 + 1 file changed, 1 insertion(+)