| Message ID | 20240609222428.134977-3-seb-dev@mail.de (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | RK3588: FriendlyElec CM3588 NAS board support | expand |
On 10.06.2024 00:20, Sebastian Kropatsch wrote: > The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on > the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board. > To reflect the hardware setup, add device tree sources for the SoM and > the NAS daughter board as separate files. > > Hardware features: > - Rockchip RK3588 SoC > - 4GB/8GB/16GB LPDDR4x RAM > - 64GB eMMC > - MicroSD card slot > - 1x RTL8125B 2.5G Ethernet > - 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs > - 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A > - 1x USB 3.0 Type-C with DP AltMode support > - 2x HDMI 2.1 out, 1x HDMI in > - MIPI-CSI Connector, MIPI-DSI Connector > - 40-pin GPIO header > - 4 buttons: power, reset, recovery, MASK, user button > - 3.5mm Headphone out, 2.0mm PH-2A Mic in > - 5V Fan connector, PWM buzzer, IR receiver, RTC battery connector > > PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1 > speed. Data lane mapping in the DT is done like described in commit > f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588"). > > This device tree includes support for eMMC, SD card, ethernet, all USB2 > and USB3 ports, all four M.2 slots, GPU, RTC, buzzer, UART debugging as > well as the buttons and LEDs. > The GPIOs are labeled according to the schematics. > > Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de> > --- > arch/arm64/boot/dts/rockchip/Makefile | 1 + > .../rk3588-friendlyelec-cm3588-nas.dts | 759 ++++++++++++++++++ > .../rockchip/rk3588-friendlyelec-cm3588.dtsi | 655 +++++++++++++++ > 3 files changed, 1415 insertions(+) > create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts > create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi Reviewed-by: Space Meyer <git@the-space.agency> Confirmed v3 fixed the usb-c port. I only tested with a single USB 2 device, as I'm not home at the moment and don't have many options to test things here. Cheers, Space
Hi Sebastian, I propose the addition of "pwm-beeper" and "gpio-ir-receiver" to the device tree, since they are permanently mounted on the baseboard. Best regards, Tim On 10.06.2024 00:20, Sebastian Kropatsch wrote: > The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on > the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board. > To reflect the hardware setup, add device tree sources for the SoM and > the NAS daughter board as separate files. > > Hardware features: > - Rockchip RK3588 SoC > - 4GB/8GB/16GB LPDDR4x RAM > - 64GB eMMC > - MicroSD card slot > - 1x RTL8125B 2.5G Ethernet > - 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs > - 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A > - 1x USB 3.0 Type-C with DP AltMode support > - 2x HDMI 2.1 out, 1x HDMI in > - MIPI-CSI Connector, MIPI-DSI Connector > - 40-pin GPIO header > - 4 buttons: power, reset, recovery, MASK, user button > - 3.5mm Headphone out, 2.0mm PH-2A Mic in > - 5V Fan connector, PWM buzzer, IR receiver, RTC battery connector > > PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1 > speed. Data lane mapping in the DT is done like described in commit > f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588"). > > This device tree includes support for eMMC, SD card, ethernet, all USB2 > and USB3 ports, all four M.2 slots, GPU, RTC, buzzer, UART debugging as > well as the buttons and LEDs. > The GPIOs are labeled according to the schematics. > > Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de> > --- > arch/arm64/boot/dts/rockchip/Makefile | 1 + > .../rk3588-friendlyelec-cm3588-nas.dts | 759 ++++++++++++++++++ > .../rockchip/rk3588-friendlyelec-cm3588.dtsi | 655 +++++++++++++++ > 3 files changed, 1415 insertions(+) > create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts > create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi > > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile > index 22f7ba98175b..85d949f2c909 100644 > --- a/arch/arm64/boot/dts/rockchip/Makefile > +++ b/arch/arm64/boot/dts/rockchip/Makefile > @@ -122,6 +122,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-wifi.dtbo > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-friendlyelec-cm3588-nas.dtb > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb > diff --git a/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts > new file mode 100644 > index 000000000000..3e3830437bf7 > --- /dev/null > +++ b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts > @@ -0,0 +1,759 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2021 Rockchip Electronics Co., Ltd. > + * Copyright (c) 2023 Thomas McKahan > + * Copyright (c) 2024 Sebastian Kropatsch > + * > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/pinctrl/rockchip.h> > +#include <dt-bindings/usb/pd.h> > +#include "rk3588-friendlyelec-cm3588.dtsi" > + > +/ { > + model = "FriendlyElec CM3588 NAS"; > + compatible = "friendlyarm,cm3588-nas", "friendlyarm,cm3588", "rockchip,rk3588"; > + > + adc_key_recovery: adc-key-recovery { > + compatible = "adc-keys"; > + io-channels = <&saradc 1>; > + io-channel-names = "buttons"; > + keyup-threshold-microvolt = <1800000>; > + poll-interval = <100>; > + > + button-recovery { > + label = "Recovery"; > + linux,code = <KEY_VENDOR>; > + press-threshold-microvolt = <17000>; > + }; > + }; > + > + analog-sound { > + compatible = "simple-audio-card"; > + pinctrl-names = "default"; > + pinctrl-0 = <&headphone_detect>; > + > + simple-audio-card,name = "realtek,rt5616-codec"; > + simple-audio-card,format = "i2s"; > + simple-audio-card,mclk-fs = <256>; > + > + simple-audio-card,hp-det-gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_LOW>; > + > + simple-audio-card,routing = > + "Headphones", "HPOL", > + "Headphones", "HPOR", > + "MIC1", "Microphone Jack", > + "Microphone Jack", "micbias1"; > + simple-audio-card,widgets = > + "Headphone", "Headphones", > + "Microphone", "Microphone Jack"; > + > + simple-audio-card,cpu { > + sound-dai = <&i2s0_8ch>; > + }; > + > + simple-audio-card,codec { > + sound-dai = <&rt5616>; > + }; > + }; > + > + fan: pwm-fan { > + compatible = "pwm-fan"; > + #cooling-cells = <2>; > + cooling-levels = <0 50 80 120 160 220>; > + fan-supply = <&vcc_5v0_sys>; > + pwms = <&pwm1 0 50000 0>; > + }; > + > + gpio_keys: gpio-keys { > + compatible = "gpio-keys"; > + pinctrl-names = "default"; > + pinctrl-0 = <&key1_pin>; > + > + button-user { > + debounce-interval = <50>; > + gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_LOW>; > + label = "User Button"; > + linux,code = <BTN_1>; > + wakeup-source; > + }; > + }; > + > + vcc_12v_dcin: regulator-vcc-12v-dcin { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_12v_dcin"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + }; > + > + vcc_3v3_m2_a: regulator-vcc-3v3-m2-a { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_3v3_m2_a"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_12v_dcin>; > + }; > + > + vcc_3v3_m2_b: regulator-vcc-3v3-m2-b { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_3v3_m2_b"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_12v_dcin>; > + }; > + > + vcc_3v3_m2_c: regulator-vcc-3v3-m2-c { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_3v3_m2_c"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_12v_dcin>; > + }; > + > + vcc_3v3_m2_d: regulator-vcc-3v3-m2-d { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_3v3_m2_d"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_12v_dcin>; > + }; > + > + /* vcc_5v0_sys powers the peripherals */ > + vcc_5v0_sys: regulator-vcc-5v0-sys { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_5v0_sys"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_12v_dcin>; > + }; > + > + vcc_5v0_host_20: regulator-vcc-5v0-host-20 { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&vcc_5v0_host20_en>; > + regulator-name = "vcc_5v0_host_20"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_5v0_sys>; > + }; > + > + vcc_5v0_host_30_p1: regulator-vcc-5v0-host-30-p1 { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&vcc_5v0_host30p1_en>; > + regulator-name = "vcc_5v0_host_30_p1"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_5v0_sys>; > + }; > + > + vcc_5v0_host_30_p2: regulator-vcc-5v0-host-30-p2 { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&vcc_5v0_host30p2_en>; > + regulator-name = "vcc_5v0_host_30_p2"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_5v0_sys>; > + }; > + > + vbus_5v0_typec: regulator-vbus-5v0-typec { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&typec_5v_pwr_en>; > + regulator-name = "vbus_5v0_typec"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_5v0_sys>; > + }; > +}; > + > +/* vcc_4v0_sys powers the RK806 and RK860's */ > +&vcc_4v0_sys { > + vin-supply = <&vcc_12v_dcin>; > +}; > + > +/* Combo PHY 1 is configured to act as as PCIe 2.0 PHY */ > +/* Used by PCIe controller 2 (pcie2x1l0) */ > +&combphy1_ps { > + status = "okay"; > +}; > + > +/* Combo PHY 2 is configured to act as USB3 PHY */ > +/* Used by USB 3.0 OTG 2 controller (USB 3.0 Type-A port 2) */ > +/* CM3588 USB Controller Config Table: USB30 HOST2 */ > +&combphy2_psu { > + status = "okay"; > +}; > + > +/* GPIO names are in the format "Human-readable-name [SIGNAL_LABEL]" */ > +/* Signal labels match the official CM3588 NAS SDK schematic revision 2309 */ > +&gpio0 { > + gpio-line-names = > + /* GPIO0 A0-A7 */ > + "", "", "", "", > + "MicroSD detect [SDMMC_DET_L]", "", "", "", > + /* GPIO0 B0-B7 */ > + "", "", "", "", > + "", "", "", "", > + /* GPIO0 C0-C7 */ > + "", "", "", "", > + "Pin 10 [UART0_RX_M0]", "Pin 08 [UART0_TX_M0/PWM4_M0]", "Pin 32 [PWM5_M1]", "", > + /* GPIO0 D0-D7 */ > + "", "", "", "USB3 Type-C [CC_INT_L]", > + "IR sensor [PWM3_IR_M0]", "User Button", "", ""; > +}; > + > +&gpio1 { > + gpio-line-names = > + /* GPIO1 A0-A7 */ > + "Pin 27 [UART6_RX_M1]", "Pin 28 [UART6_TX_M1]", "", "", > + "USB2 Type-A [USB2_PWREN]", "", "", "Pin 15", > + /* GPIO1 B0-B7 */ > + "Pin 26", "Pin 21 [SPI0_MISO_M2]", "Pin 19 [SPI0_MOSI_M2/UART4_RX_M2]", "Pin 23 [SPI0_CLK_M2/UART4_TX_M2]", > + "Pin 24 [SPI0_CS0_M2/UART7_RX_M2]", "Pin 22 [SPI0_CS1_M0/UART7_TX_M2]", "", "CSI-Pin 14 [MIPI_CAM2_CLKOUT]", > + /* GPIO1 C0-C7 */ > + "", "", "", "", > + "Headphone detect [HP_DET_L]", "", "", "", > + /* GPIO1 D0-D7 */ > + "", "", "USB3 Type-C [TYPEC5V_PWREN_H]", "5V Fan [PWM1_M1]", > + "", "HDMI-in detect [HDMIIRX_DET_L]", "Pin 05 [I2C8_SCL_M2]", "Pin 03 [I2C8_SDA_M2]"; > +}; > + > +&gpio2 { > + gpio-line-names = > + /* GPIO2 A0-A7 */ > + "", "", "", "", > + "", "", "SPI NOR Flash [FSPI_D0_M1]", "SPI NOR Flash [FSPI_D1_M1]", > + /* GPIO2 B0-B7 */ > + "SPI NOR Flash [FSPI_D2_M1]", "SPI NOR Flash [FSPI_D3_M1]", "", "SPI NOR Flash [FSPI_CLK_M1]", > + "SPI NOR Flash [FSPI_CSN0_M1]", "", "", "", > + /* GPIO2 C0-C7 */ > + "", "CSI-Pin 11 [MIPI_CAM2_RESET_L]", "CSI-Pin 12 [MIPI_CAM2_PDN_L]", "", > + "", "", "", "", > + /* GPIO2 D0-D7 */ > + "", "", "", "", > + "", "", "", ""; > +}; > + > +&gpio3 { > + gpio-line-names = > + /* GPIO3 A0-A7 */ > + "Pin 35 [SPI4_MISO_M1/PWM10_M0]", "Pin 38 [SPI4_MOSI_M1]", "Pin 40 [SPI4_CLK_M1/UART8_TX_M1]", "Pin 36 [SPI4_CS0_M1/UART8_RX_M1]", > + "Pin 37 [SPI4_CS1_M1]", "USB3-A #2 [USB3_2_PWREN]", "DSI-Pin 12 [LCD_RST]", "Buzzer [PWM8_M0]", > + /* GPIO3 B0-B7 */ > + "Pin 33 [PWM9_M0]", "DSI-Pin 10 [PWM2_M1/LCD_BL]", "Pin 07", "Pin 16", > + "Pin 18", "Pin 29 [UART3_TX_M1/PWM12_M0]", "Pin 31 [UART3_RX_M1/PWM13_M0]", "Pin 12", > + /* GPIO3 C0-C7 */ > + "DSI-Pin 08 [TP_INT_L]", "DSI-Pin 14 [TP_RST_L]", "Pin 11 [PWM14_M0]", "Pin 13 [PWM15_IR_M0]", > + "", "", "", "DSI-Pin 06 [I2C5_SCL_M0_TP]", > + /* GPIO3 D0-D7 */ > + "DSI-Pin 05 [I2C5_SDA_M0_TP]", "", "", "", > + "", "", "", ""; > +}; > + > +&gpio4 { > + gpio-line-names = > + /* GPIO4 A0-A7 */ > + "", "", "M.2 M-Key Slot4 [M2_D_PERST_L]", "", > + "", "", "", "", > + /* GPIO4 B0-B7 */ > + "USB3-A #1 [USB3_TYPEC1_PWREN]", "", "", "M.2 M-Key Slot3 [M2_C_PERST_L]", > + "M.2 M-Key Slot2 [M2_B_PERST_L]", "M.2 M-Key Slot1 [M2_A_CLKREQ_L]", "M.2 M-Key Slot1 [M2_A_PERST_L]", "", > + /* GPIO4 C0-C7 */ > + "", "", "", "", > + "", "", "", "", > + /* GPIO4 D0-D7 */ > + "", "", "", "", > + "", "", "", ""; > +}; > + > +/* Connected to MIPI-DSI0 */ > +&i2c5 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c5m0_xfer>; > + status = "disabled"; > +}; > + > +&i2c6 { > + fusb302: typec-portc@22 { > + compatible = "fcs,fusb302"; > + reg = <0x22>; > + interrupt-parent = <&gpio0>; > + interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usbc0_int>; > + vbus-supply = <&vbus_5v0_typec>; > + > + usb_con: connector { > + compatible = "usb-c-connector"; > + data-role = "dual"; > + label = "USB-C"; > + power-role = "source"; > + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; > + try-power-role = "source"; > + vbus-supply = <&vbus_5v0_typec>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + usbc0_orien_sw: endpoint { > + remote-endpoint = <&usbdp_phy0_orientation_switch>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + usbc0_role_sw: endpoint { > + remote-endpoint = <&dwc3_0_role_switch>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + dp_altmode_mux: endpoint { > + remote-endpoint = <&usbdp_phy0_dp_altmode_mux>; > + }; > + }; > + }; > + }; > + }; > +}; > + > +/* Connected to MIPI-CSI1 */ > +/* &i2c7 */ > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +&i2c8 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c8m2_xfer>; > + status = "okay"; > +}; > + > +&pcie2x1l0 { > + /* 2. M.2 socket, CON14: pcie30phy port0 lane1, @fe170000 */ > + max-link-speed = <3>; > + num-lanes = <1>; > + phys = <&pcie30phy>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie2_0_rst>; > + reset-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; > + vpcie3v3-supply = <&vcc_3v3_m2_b>; > + status = "okay"; > +}; > + > +&pcie2x1l1 { > + /* 4. M.2 socket, CON16: pcie30phy port1 lane1, @fe180000 */ > + max-link-speed = <3>; > + num-lanes = <1>; > + phys = <&pcie30phy>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie2_1_rst>; > + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>; > + vpcie3v3-supply = <&vcc_3v3_m2_d>; > + status = "okay"; > +}; > + > +&pcie30phy { > + /* > + * Data lane mapping <1 3 2 4> = x1x1 x1x1 (bifurcation of both ports) > + * port 0 lane 0 - always mapped to controller 0 (4L) > + * port 0 lane 1 - map to controller 2 (1L0) > + * port 1 lane 0 - map to controller 1 (2L) > + * port 1 lane 1 - map to controller 3 (1L1) > + */ > + data-lanes = <1 3 2 4>; > + status = "okay"; > +}; > + > +&pcie3x4 { > + /* 1. M.2 socket, CON13: pcie30phy port0 lane0, @fe150000 */ > + max-link-speed = <3>; > + num-lanes = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie3x4_rst>; > + reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>; > + vpcie3v3-supply = <&vcc_3v3_m2_a>; > + status = "okay"; > +}; > + > +&pcie3x2 { > + /* 3. M.2 socket, CON15: pcie30phy port1 lane0, @fe160000 */ > + max-link-speed = <3>; > + num-lanes = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie3x2_rst>; > + reset-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>; > + vpcie3v3-supply = <&vcc_3v3_m2_c>; > + status = "okay"; > +}; > + > +&pinctrl { > + audio { > + headphone_detect: headphone-detect { > + rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + gpio-key { > + key1_pin: key1-pin { > + rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + pcie { > + pcie2_0_rst: pcie2-0-rst { > + rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + pcie2_1_rst: pcie2-1-rst { > + rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + pcie3x2_rst: pcie3x2-rst { > + rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + pcie3x4_rst: pcie3x4-rst { > + rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + usb { > + vcc_5v0_host20_en: vcc-5v0-host20-en { > + rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + vcc_5v0_host30p1_en: vcc-5v0-host30p1-en { > + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + vcc_5v0_host30p2_en: vcc-5v0-host30p2-en { > + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + usb-typec { > + usbc0_int: usbc0-int { > + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + > + typec_5v_pwr_en: typec-5v-pwr-en { > + rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > +}; > + > +/* Connected to 5V Fan */ > +&pwm1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm1m1_pins>; > + status = "okay"; > +}; > + > +/* Connected to MIPI-DSI0 */ > +&pwm2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm2m1_pins>; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with UART0 */ > +&pwm4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm4m1_pins>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +&pwm5 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm5m1_pins>; > + status = "okay"; > +}; > + > +/* Buzzer */ > +&pwm8 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm8m0_pins>; > + status = "okay"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +&pwm9 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm9m0_pins>; > + status = "okay"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with SPI4 */ > +&pwm10 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm10m0_pins>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with UART3 */ > +&pwm12 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm12m0_pins>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with UART3 */ > +&pwm13 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm13m0_pins>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +&pwm14 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm14m0_pins>; > + status = "okay"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Optimized for infrared applications */ > +&pwm15 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm15m0_pins>; > + status = "disabled"; > +}; > + > +/* microSD card */ > +&sdmmc { > + status = "okay"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with UART4, UART7 and PWM10 */ > +&spi0 { > + num-cs = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0m2_cs0 &spi0m2_pins>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with UART8 */ > +&spi4 { > + num-cs = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi4m1_cs0 &spi4m1_pins>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with PWM4 */ > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0m0_xfer>; > + status = "disabled"; > +}; > + > +/* Debug UART */ > +&uart2 { > + status = "okay"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with PWM12 and PWM13 */ > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart3m1_xfer>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with SPI0 */ > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart4m2_xfer>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +&uart6 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart6m1_xfer>; > + status = "okay"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with SPI0 */ > +&uart7 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart7m2_xfer>; > + status = "disabled"; > +}; > + > +/* GPIO Connector, connected to 40-pin GPIO header */ > +/* Shared with SPI4 */ > +&uart8 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart8m1_xfer>; > + status = "disabled"; > +}; > + > +/* USB2 PHY for USB Type-C port */ > +/* CM3588 USB Controller Config Table: USB20 OTG0 */ > +&u2phy0 { > + status = "okay"; > +}; > + > +&u2phy0_otg { > + phy-supply = <&vbus_5v0_typec>; > + status = "okay"; > +}; > + > +/* USB2 PHY for USB 3.0 Type-A port 1 */ > +/* CM3588 USB Controller Config Table: USB20 OTG1 */ > +&u2phy1 { > + status = "okay"; > +}; > + > +&u2phy1_otg { > + phy-supply = <&vcc_5v0_host_30_p1>; > + status = "okay"; > +}; > + > +/* USB2 PHY for USB 2.0 Type-A */ > +/* CM3588 USB Controller Config Table: USB20 HOST0 */ > +&u2phy2 { > + status = "okay"; > +}; > + > +&u2phy2_host { > + phy-supply = <&vcc_5v0_host_20>; > + status = "okay"; > +}; > + > +/* USB2 PHY for USB 3.0 Type-A port 2 */ > +/* CM3588 USB Controller Config Table: USB20 HOST1 */ > +&u2phy3 { > + status = "okay"; > +}; > + > +&u2phy3_host { > + phy-supply = <&vcc_5v0_host_30_p2>; > + status = "okay"; > +}; > + > +/* USB 2.0 Type-A */ > +/* PHYs: <&u2phy2_host> */ > +&usb_host0_ehci { > + status = "okay"; > +}; > + > +/* USB 2.0 Type-A */ > +/* PHYs: <&u2phy2_host> */ > +&usb_host0_ohci { > + status = "okay"; > +}; > + > +/* USB Type-C */ > +/* PHYs: <&u2phy0_otg>, <&usbdp_phy0 PHY_TYPE_USB3> */ > +&usb_host0_xhci { > + usb-role-switch; > + status = "okay"; > + > + port { > + #address-cells = <1>; > + #size-cells = <0>; > + > + dwc3_0_role_switch: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&usbc0_role_sw>; > + }; > + }; > +}; > + > +/* Lower USB 3.0 Type-A (port 2) */ > +/* PHYs: <&u2phy3_host> */ > +&usb_host1_ehci { > + status = "okay"; > +}; > + > +/* Lower USB 3.0 Type-A (port 2) */ > +/* PHYs: <&u2phy3_host> */ > +&usb_host1_ohci { > + status = "okay"; > +}; > + > +/* Upper USB 3.0 Type-A (port 1) */ > +/* PHYs: <&u2phy1_otg>, <&usbdp_phy1 PHY_TYPE_USB3> */ > +&usb_host1_xhci { > + dr_mode = "host"; > + status = "okay"; > +}; > + > +/* Lower USB 3.0 Type-A (port 2) */ > +/* PHYs: <&combphy2_psu PHY_TYPE_USB3> */ > +&usb_host2_xhci { > + status = "okay"; > +}; > + > +/* USB3 PHY for USB Type-C port */ > +/* CM3588 USB Controller Config Table: USB30 OTG0 */ > +&usbdp_phy0 { > + orientation-switch; > + sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>; > + sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + > + port { > + #address-cells = <1>; > + #size-cells = <0>; > + > + usbdp_phy0_orientation_switch: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&usbc0_orien_sw>; > + }; > + > + usbdp_phy0_dp_altmode_mux: endpoint@1 { > + reg = <1>; > + remote-endpoint = <&dp_altmode_mux>; > + }; > + }; > +}; > + > +/* USB3 PHY for USB 3.0 Type-A port 1 */ > +/* CM3588 USB Controller Config Table: USB30 OTG1 */ > +&usbdp_phy1 { > + status = "okay"; > +}; > diff --git a/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi > new file mode 100644 > index 000000000000..b1062380b4f2 > --- /dev/null > +++ b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi > @@ -0,0 +1,655 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2021 Rockchip Electronics Co., Ltd. > + * Copyright (c) 2023 Thomas McKahan > + * Copyright (c) 2024 Sebastian Kropatsch > + * > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/rockchip.h> > +#include "rk3588.dtsi" > + > +/ { > + model = "FriendlyElec CM3588"; > + compatible = "friendlyarm,cm3588", "rockchip,rk3588"; > + > + aliases { > + mmc0 = &sdhci; > + mmc1 = &sdmmc; > + }; > + > + chosen { > + stdout-path = "serial2:1500000n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led_sys: led-0 { > + color = <LED_COLOR_ID_AMBER>; > + function = LED_FUNCTION_HEARTBEAT; > + gpios = <&gpio2 RK_PC5 GPIO_ACTIVE_HIGH>; > + label = "system-led"; > + linux,default-trigger = "heartbeat"; > + pinctrl-names = "default"; > + pinctrl-0 = <&led_sys_pin>; > + }; > + > + led_usr: led-1 { > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; > + label = "user-led"; > + pinctrl-names = "default"; > + pinctrl-0 = <&led_usr_pin>; > + }; > + }; > + > + /* vcc_4v0_sys powers the RK806 and RK860's */ > + vcc_4v0_sys: regulator-vcc-4v0-sys { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_4v0_sys"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <4000000>; > + regulator-max-microvolt = <4000000>; > + }; > + > + vcc_3v3_pcie20: regulator-vcc-3v3-pcie20 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_3v3_pcie20"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_3v3_s3>; > + }; > + > + vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 { > + compatible = "regulator-fixed"; > + gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sd_s0_pwr>; > + regulator-boot-on; > + regulator-max-microvolt = <3300000>; > + regulator-min-microvolt = <3300000>; > + regulator-name = "vcc_3v3_sd_s0"; > + vin-supply = <&vcc_3v3_s3>; > + }; > + > + vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc-1v1-nldo-s3"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + vin-supply = <&vcc_4v0_sys>; > + }; > +}; > + > +/* Combo PHY 0 is configured to act as as PCIe 2.0 PHY */ > +/* Used by PCIe controller 4 (pcie2x1l2) */ > +&combphy0_ps { > + status = "okay"; > +}; > + > +&cpu_l0 { > + cpu-supply = <&vdd_cpu_lit_s0>; > +}; > + > +&cpu_l1 { > + cpu-supply = <&vdd_cpu_lit_s0>; > +}; > + > +&cpu_l2 { > + cpu-supply = <&vdd_cpu_lit_s0>; > +}; > + > +&cpu_l3 { > + cpu-supply = <&vdd_cpu_lit_s0>; > +}; > + > +&cpu_b0 { > + cpu-supply = <&vdd_cpu_big0_s0>; > +}; > + > +&cpu_b1 { > + cpu-supply = <&vdd_cpu_big0_s0>; > +}; > + > +&cpu_b2 { > + cpu-supply = <&vdd_cpu_big1_s0>; > +}; > + > +&cpu_b3 { > + cpu-supply = <&vdd_cpu_big1_s0>; > +}; > + > +&gpu { > + mali-supply = <&vdd_gpu_s0>; > + sram-supply = <&vdd_gpu_mem_s0>; > + status = "okay"; > +}; > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0m2_xfer>; > + status = "okay"; > + > + vdd_cpu_big0_s0: regulator@42 { > + compatible = "rockchip,rk8602"; > + reg = <0x42>; > + fcs,suspend-voltage-selector = <1>; > + regulator-name = "vdd_cpu_big0_s0"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <1050000>; > + regulator-ramp-delay = <2300>; > + vin-supply = <&vcc_4v0_sys>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_cpu_big1_s0: regulator@43 { > + compatible = "rockchip,rk8603", "rockchip,rk8602"; > + reg = <0x43>; > + fcs,suspend-voltage-selector = <1>; > + regulator-name = "vdd_cpu_big1_s0"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <1050000>; > + regulator-ramp-delay = <2300>; > + vin-supply = <&vcc_4v0_sys>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > + > + vdd_npu_s0: regulator@42 { > + compatible = "rockchip,rk8602"; > + reg = <0x42>; > + fcs,suspend-voltage-selector = <1>; > + regulator-name = "vdd_npu_s0"; > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <950000>; > + regulator-ramp-delay = <2300>; > + vin-supply = <&vcc_4v0_sys>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > +}; > + > +&i2c6 { > + clock-frequency = <200000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c6m0_xfer>; > + status = "okay"; > + > + hym8563: rtc@51 { > + compatible = "haoyu,hym8563"; > + reg = <0x51>; > + #clock-cells = <0>; > + clock-output-names = "hym8563"; > + interrupt-parent = <&gpio0>; > + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&hym8563_int>; > + wakeup-source; > + }; > +}; > + > +&i2c7 { > + clock-frequency = <200000>; > + status = "okay"; > + > + rt5616: audio-codec@1b { > + compatible = "realtek,rt5616"; > + reg = <0x1b>; > + #sound-dai-cells = <0>; > + }; > +}; > + > +&i2s0_8ch { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2s0_lrck > + &i2s0_mclk > + &i2s0_sclk > + &i2s0_sdi0 > + &i2s0_sdo0>; > + status = "okay"; > +}; > + > +&i2s5_8ch { > + status = "okay"; > +}; > + > +&i2s6_8ch { > + status = "okay"; > +}; > + > +&i2s7_8ch { > + status = "okay"; > +}; > + > +&pcie2x1l2 { > + /* r8125 ethernet, @fe190000 */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie2_2_rst>; > + reset-gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>; > + vpcie3v3-supply = <&vcc_3v3_pcie20>; > + status = "okay"; > +}; > + > +&pinctrl { > + gpio-leds { > + led_sys_pin: led-sys-pin { > + rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + led_usr_pin: led-usr-pin { > + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + hym8563 { > + hym8563_int: hym8563-int { > + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + pcie { > + pcie2_2_rst: pcie2-2-rst { > + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + sdmmc { > + sd_s0_pwr: sd-s0-pwr { > + rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > +}; > + > +&saradc { > + vref-supply = <&avcc_1v8_s0>; > + status = "okay"; > +}; > + > +/* eMMC */ > +&sdhci { > + bus-width = <8>; > + mmc-hs400-1_8v; > + mmc-hs400-enhanced-strobe; > + no-sd; > + no-sdio; > + non-removable; > + vmmc-supply = <&vcc_3v3_s3>; > + vqmmc-supply = <&vcc_1v8_s3>; > + status = "okay"; > +}; > + > +/* microSD card */ > +&sdmmc { > + bus-width = <4>; > + cap-sd-highspeed; > + disable-wp; > + max-frequency = <150000000>; > + no-mmc; > + no-sdio; > + sd-uhs-sdr104; > + vmmc-supply = <&vcc_3v3_sd_s0>; > + vqmmc-supply = <&vccio_sd_s0>; > +}; > + > +&spi2 { > + assigned-clocks = <&cru CLK_SPI2>; > + assigned-clock-rates = <200000000>; > + num-cs = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>; > + status = "okay"; > + > + rk806_single: pmic@0 { > + compatible = "rockchip,rk806"; > + reg = <0x0>; > + > + interrupt-parent = <&gpio0>; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, > + <&rk806_dvs2_null>, <&rk806_dvs3_null>; > + > + spi-max-frequency = <1000000>; > + > + system-power-controller; > + > + vcc1-supply = <&vcc_4v0_sys>; > + vcc2-supply = <&vcc_4v0_sys>; > + vcc3-supply = <&vcc_4v0_sys>; > + vcc4-supply = <&vcc_4v0_sys>; > + vcc5-supply = <&vcc_4v0_sys>; > + vcc6-supply = <&vcc_4v0_sys>; > + vcc7-supply = <&vcc_4v0_sys>; > + vcc8-supply = <&vcc_4v0_sys>; > + vcc9-supply = <&vcc_4v0_sys>; > + vcc10-supply = <&vcc_4v0_sys>; > + vcc11-supply = <&vcc_2v0_pldo_s3>; > + vcc12-supply = <&vcc_4v0_sys>; > + vcc13-supply = <&vcc_1v1_nldo_s3>; > + vcc14-supply = <&vcc_1v1_nldo_s3>; > + vcca-supply = <&vcc_4v0_sys>; > + > + gpio-controller; > + #gpio-cells = <2>; > + > + rk806_dvs1_null: dvs1-null-pins { > + pins = "gpio_pwrctrl1"; > + function = "pin_fun0"; > + }; > + > + rk806_dvs2_null: dvs2-null-pins { > + pins = "gpio_pwrctrl2"; > + function = "pin_fun0"; > + }; > + > + rk806_dvs3_null: dvs3-null-pins { > + pins = "gpio_pwrctrl3"; > + function = "pin_fun0"; > + }; > + > + regulators { > + vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 { > + regulator-boot-on; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <950000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vdd_gpu_s0"; > + regulator-enable-ramp-delay = <400>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <950000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vdd_cpu_lit_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_log_s0: dcdc-reg3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <675000>; > + regulator-max-microvolt = <750000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vdd_log_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <750000>; > + }; > + }; > + > + vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <950000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vdd_vdenc_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_ddr_s0: dcdc-reg5 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <675000>; > + regulator-max-microvolt = <900000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vdd_ddr_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <850000>; > + }; > + }; > + > + vdd2_ddr_s3: dcdc-reg6 { > + regulator-always-on; > + regulator-boot-on; > + regulator-name = "vdd2_ddr_s3"; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + vcc_2v0_pldo_s3: dcdc-reg7 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <2000000>; > + regulator-max-microvolt = <2000000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vdd_2v0_pldo_s3"; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <2000000>; > + }; > + }; > + > + vcc_3v3_s3: dcdc-reg8 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc_3v3_s3"; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <3300000>; > + }; > + }; > + > + vddq_ddr_s0: dcdc-reg9 { > + regulator-always-on; > + regulator-boot-on; > + regulator-name = "vddq_ddr_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_1v8_s3: dcdc-reg10 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc_1v8_s3"; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + avcc_1v8_s0: pldo-reg1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "avcc_1v8_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_1v8_s0: pldo-reg2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc_1v8_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + avdd_1v2_s0: pldo-reg3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-name = "avdd_1v2_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_3v3_s0: pldo-reg4 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vcc_3v3_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vccio_sd_s0: pldo-reg5 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-ramp-delay = <12500>; > + regulator-name = "vccio_sd_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + pldo6_s3: pldo-reg6 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "pldo6_s3"; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + vdd_0v75_s3: nldo-reg1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <750000>; > + regulator-name = "vdd_0v75_s3"; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <750000>; > + }; > + }; > + > + vdd_ddr_pll_s0: nldo-reg2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <850000>; > + regulator-name = "vdd_ddr_pll_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-suspend-microvolt = <850000>; > + }; > + }; > + > + avdd_0v75_s0: nldo-reg3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <750000>; > + regulator-name = "avdd_0v75_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_0v85_s0: nldo-reg4 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <850000>; > + regulator-name = "vdd_0v85_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_0v75_s0: nldo-reg5 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <750000>; > + regulator-max-microvolt = <750000>; > + regulator-name = "vdd_0v75_s0"; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + }; > + }; > +}; > + > +&tsadc { > + status = "okay"; > +}; > + > +/* Debug UART */ > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart2m0_xfer>; > +};
Hi Tim, Am 14.06.2024 um 04:00 schrieb Tim Surber: > Hi Sebastian, > > I propose the addition of "pwm-beeper" and "gpio-ir-receiver" to the > device tree, since they are permanently mounted on the baseboard. Can you recommend a good way to test the IR receiver? I tried for a while with evtest but could not see any output: evtest /dev/input/event2 Input driver version is 1.0.1 Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100 Input device name: "gpio_ir_recv" Supported events: Event type 0 (EV_SYN) Event type 1 (EV_KEY) Event code 152 (KEY_SCREENLOCK) Event type 2 (EV_REL) Event code 0 (REL_X) Event code 1 (REL_Y) Event type 4 (EV_MSC) Event code 4 (MSC_SCAN) Key repeat handling: Repeat type 20 (EV_REP) Repeat code 0 (REP_DELAY) Value 500 Repeat code 1 (REP_PERIOD) Value 125 Properties: Property type 5 (INPUT_PROP_POINTING_STICK) Testing ... (interrupt to exit) I only have one TV remote to test, so I'm not even sure that this is compatible, I haven't touched anything IR-related before. Cheers, Sebastian > On 10.06.2024 00:20, Sebastian Kropatsch wrote: >> The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on >> the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board. >> To reflect the hardware setup, add device tree sources for the SoM and >> the NAS daughter board as separate files. >> >> Hardware features: >>     - Rockchip RK3588 SoC >>     - 4GB/8GB/16GB LPDDR4x RAM >>     - 64GB eMMC >>     - MicroSD card slot >>     - 1x RTL8125B 2.5G Ethernet >>     - 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs >>     - 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A >>     - 1x USB 3.0 Type-C with DP AltMode support >>     - 2x HDMI 2.1 out, 1x HDMI in >>     - MIPI-CSI Connector, MIPI-DSI Connector >>     - 40-pin GPIO header >>     - 4 buttons: power, reset, recovery, MASK, user button >>     - 3.5mm Headphone out, 2.0mm PH-2A Mic in >>     - 5V Fan connector, PWM buzzer, IR receiver, RTC battery connector >> >> PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1 >> speed. Data lane mapping in the DT is done like described in commit >> f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588"). >> >> This device tree includes support for eMMC, SD card, ethernet, all USB2 >> and USB3 ports, all four M.2 slots, GPU, RTC, buzzer, UART debugging as >> well as the buttons and LEDs. >> The GPIOs are labeled according to the schematics. >> >> Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de> >> --- >>  arch/arm64/boot/dts/rockchip/Makefile        |  1 + >>  .../rk3588-friendlyelec-cm3588-nas.dts       | 759 ++++++++++++++++++ >>  .../rockchip/rk3588-friendlyelec-cm3588.dtsi | 655 +++++++++++++++ >>  3 files changed, 1415 insertions(+) >>  create mode 100644 >> arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts >>  create mode 100644 >> arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi
Hi Sebastian, using the vendor kernel I had success with "sudo ir-keytable -t -p all". You have to have all the required protocols under CONFIG_RC_DECODERS enabled (the easiest is to enable them all for testing). Using the above command I can see output when using a normal Sony TV remote. I have not tested using the mainline kernel. Best regards, Tim
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile index 22f7ba98175b..85d949f2c909 100644 --- a/arch/arm64/boot/dts/rockchip/Makefile +++ b/arch/arm64/boot/dts/rockchip/Makefile @@ -122,6 +122,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-wifi.dtbo dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-friendlyelec-cm3588-nas.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb diff --git a/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts new file mode 100644 index 000000000000..3e3830437bf7 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts @@ -0,0 +1,759 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2021 Rockchip Electronics Co., Ltd. + * Copyright (c) 2023 Thomas McKahan + * Copyright (c) 2024 Sebastian Kropatsch + * + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/usb/pd.h> +#include "rk3588-friendlyelec-cm3588.dtsi" + +/ { + model = "FriendlyElec CM3588 NAS"; + compatible = "friendlyarm,cm3588-nas", "friendlyarm,cm3588", "rockchip,rk3588"; + + adc_key_recovery: adc-key-recovery { + compatible = "adc-keys"; + io-channels = <&saradc 1>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1800000>; + poll-interval = <100>; + + button-recovery { + label = "Recovery"; + linux,code = <KEY_VENDOR>; + press-threshold-microvolt = <17000>; + }; + }; + + analog-sound { + compatible = "simple-audio-card"; + pinctrl-names = "default"; + pinctrl-0 = <&headphone_detect>; + + simple-audio-card,name = "realtek,rt5616-codec"; + simple-audio-card,format = "i2s"; + simple-audio-card,mclk-fs = <256>; + + simple-audio-card,hp-det-gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_LOW>; + + simple-audio-card,routing = + "Headphones", "HPOL", + "Headphones", "HPOR", + "MIC1", "Microphone Jack", + "Microphone Jack", "micbias1"; + simple-audio-card,widgets = + "Headphone", "Headphones", + "Microphone", "Microphone Jack"; + + simple-audio-card,cpu { + sound-dai = <&i2s0_8ch>; + }; + + simple-audio-card,codec { + sound-dai = <&rt5616>; + }; + }; + + fan: pwm-fan { + compatible = "pwm-fan"; + #cooling-cells = <2>; + cooling-levels = <0 50 80 120 160 220>; + fan-supply = <&vcc_5v0_sys>; + pwms = <&pwm1 0 50000 0>; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&key1_pin>; + + button-user { + debounce-interval = <50>; + gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_LOW>; + label = "User Button"; + linux,code = <BTN_1>; + wakeup-source; + }; + }; + + vcc_12v_dcin: regulator-vcc-12v-dcin { + compatible = "regulator-fixed"; + regulator-name = "vcc_12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc_3v3_m2_a: regulator-vcc-3v3-m2-a { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_m2_a"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_12v_dcin>; + }; + + vcc_3v3_m2_b: regulator-vcc-3v3-m2-b { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_m2_b"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_12v_dcin>; + }; + + vcc_3v3_m2_c: regulator-vcc-3v3-m2-c { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_m2_c"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_12v_dcin>; + }; + + vcc_3v3_m2_d: regulator-vcc-3v3-m2-d { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_m2_d"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_12v_dcin>; + }; + + /* vcc_5v0_sys powers the peripherals */ + vcc_5v0_sys: regulator-vcc-5v0-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc_5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_12v_dcin>; + }; + + vcc_5v0_host_20: regulator-vcc-5v0-host-20 { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc_5v0_host20_en>; + regulator-name = "vcc_5v0_host_20"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v0_sys>; + }; + + vcc_5v0_host_30_p1: regulator-vcc-5v0-host-30-p1 { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc_5v0_host30p1_en>; + regulator-name = "vcc_5v0_host_30_p1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v0_sys>; + }; + + vcc_5v0_host_30_p2: regulator-vcc-5v0-host-30-p2 { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc_5v0_host30p2_en>; + regulator-name = "vcc_5v0_host_30_p2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v0_sys>; + }; + + vbus_5v0_typec: regulator-vbus-5v0-typec { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&typec_5v_pwr_en>; + regulator-name = "vbus_5v0_typec"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v0_sys>; + }; +}; + +/* vcc_4v0_sys powers the RK806 and RK860's */ +&vcc_4v0_sys { + vin-supply = <&vcc_12v_dcin>; +}; + +/* Combo PHY 1 is configured to act as as PCIe 2.0 PHY */ +/* Used by PCIe controller 2 (pcie2x1l0) */ +&combphy1_ps { + status = "okay"; +}; + +/* Combo PHY 2 is configured to act as USB3 PHY */ +/* Used by USB 3.0 OTG 2 controller (USB 3.0 Type-A port 2) */ +/* CM3588 USB Controller Config Table: USB30 HOST2 */ +&combphy2_psu { + status = "okay"; +}; + +/* GPIO names are in the format "Human-readable-name [SIGNAL_LABEL]" */ +/* Signal labels match the official CM3588 NAS SDK schematic revision 2309 */ +&gpio0 { + gpio-line-names = + /* GPIO0 A0-A7 */ + "", "", "", "", + "MicroSD detect [SDMMC_DET_L]", "", "", "", + /* GPIO0 B0-B7 */ + "", "", "", "", + "", "", "", "", + /* GPIO0 C0-C7 */ + "", "", "", "", + "Pin 10 [UART0_RX_M0]", "Pin 08 [UART0_TX_M0/PWM4_M0]", "Pin 32 [PWM5_M1]", "", + /* GPIO0 D0-D7 */ + "", "", "", "USB3 Type-C [CC_INT_L]", + "IR sensor [PWM3_IR_M0]", "User Button", "", ""; +}; + +&gpio1 { + gpio-line-names = + /* GPIO1 A0-A7 */ + "Pin 27 [UART6_RX_M1]", "Pin 28 [UART6_TX_M1]", "", "", + "USB2 Type-A [USB2_PWREN]", "", "", "Pin 15", + /* GPIO1 B0-B7 */ + "Pin 26", "Pin 21 [SPI0_MISO_M2]", "Pin 19 [SPI0_MOSI_M2/UART4_RX_M2]", "Pin 23 [SPI0_CLK_M2/UART4_TX_M2]", + "Pin 24 [SPI0_CS0_M2/UART7_RX_M2]", "Pin 22 [SPI0_CS1_M0/UART7_TX_M2]", "", "CSI-Pin 14 [MIPI_CAM2_CLKOUT]", + /* GPIO1 C0-C7 */ + "", "", "", "", + "Headphone detect [HP_DET_L]", "", "", "", + /* GPIO1 D0-D7 */ + "", "", "USB3 Type-C [TYPEC5V_PWREN_H]", "5V Fan [PWM1_M1]", + "", "HDMI-in detect [HDMIIRX_DET_L]", "Pin 05 [I2C8_SCL_M2]", "Pin 03 [I2C8_SDA_M2]"; +}; + +&gpio2 { + gpio-line-names = + /* GPIO2 A0-A7 */ + "", "", "", "", + "", "", "SPI NOR Flash [FSPI_D0_M1]", "SPI NOR Flash [FSPI_D1_M1]", + /* GPIO2 B0-B7 */ + "SPI NOR Flash [FSPI_D2_M1]", "SPI NOR Flash [FSPI_D3_M1]", "", "SPI NOR Flash [FSPI_CLK_M1]", + "SPI NOR Flash [FSPI_CSN0_M1]", "", "", "", + /* GPIO2 C0-C7 */ + "", "CSI-Pin 11 [MIPI_CAM2_RESET_L]", "CSI-Pin 12 [MIPI_CAM2_PDN_L]", "", + "", "", "", "", + /* GPIO2 D0-D7 */ + "", "", "", "", + "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + /* GPIO3 A0-A7 */ + "Pin 35 [SPI4_MISO_M1/PWM10_M0]", "Pin 38 [SPI4_MOSI_M1]", "Pin 40 [SPI4_CLK_M1/UART8_TX_M1]", "Pin 36 [SPI4_CS0_M1/UART8_RX_M1]", + "Pin 37 [SPI4_CS1_M1]", "USB3-A #2 [USB3_2_PWREN]", "DSI-Pin 12 [LCD_RST]", "Buzzer [PWM8_M0]", + /* GPIO3 B0-B7 */ + "Pin 33 [PWM9_M0]", "DSI-Pin 10 [PWM2_M1/LCD_BL]", "Pin 07", "Pin 16", + "Pin 18", "Pin 29 [UART3_TX_M1/PWM12_M0]", "Pin 31 [UART3_RX_M1/PWM13_M0]", "Pin 12", + /* GPIO3 C0-C7 */ + "DSI-Pin 08 [TP_INT_L]", "DSI-Pin 14 [TP_RST_L]", "Pin 11 [PWM14_M0]", "Pin 13 [PWM15_IR_M0]", + "", "", "", "DSI-Pin 06 [I2C5_SCL_M0_TP]", + /* GPIO3 D0-D7 */ + "DSI-Pin 05 [I2C5_SDA_M0_TP]", "", "", "", + "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = + /* GPIO4 A0-A7 */ + "", "", "M.2 M-Key Slot4 [M2_D_PERST_L]", "", + "", "", "", "", + /* GPIO4 B0-B7 */ + "USB3-A #1 [USB3_TYPEC1_PWREN]", "", "", "M.2 M-Key Slot3 [M2_C_PERST_L]", + "M.2 M-Key Slot2 [M2_B_PERST_L]", "M.2 M-Key Slot1 [M2_A_CLKREQ_L]", "M.2 M-Key Slot1 [M2_A_PERST_L]", "", + /* GPIO4 C0-C7 */ + "", "", "", "", + "", "", "", "", + /* GPIO4 D0-D7 */ + "", "", "", "", + "", "", "", ""; +}; + +/* Connected to MIPI-DSI0 */ +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c5m0_xfer>; + status = "disabled"; +}; + +&i2c6 { + fusb302: typec-portc@22 { + compatible = "fcs,fusb302"; + reg = <0x22>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&usbc0_int>; + vbus-supply = <&vbus_5v0_typec>; + + usb_con: connector { + compatible = "usb-c-connector"; + data-role = "dual"; + label = "USB-C"; + power-role = "source"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + try-power-role = "source"; + vbus-supply = <&vbus_5v0_typec>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + usbc0_orien_sw: endpoint { + remote-endpoint = <&usbdp_phy0_orientation_switch>; + }; + }; + + port@1 { + reg = <1>; + + usbc0_role_sw: endpoint { + remote-endpoint = <&dwc3_0_role_switch>; + }; + }; + + port@2 { + reg = <2>; + + dp_altmode_mux: endpoint { + remote-endpoint = <&usbdp_phy0_dp_altmode_mux>; + }; + }; + }; + }; + }; +}; + +/* Connected to MIPI-CSI1 */ +/* &i2c7 */ + +/* GPIO Connector, connected to 40-pin GPIO header */ +&i2c8 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c8m2_xfer>; + status = "okay"; +}; + +&pcie2x1l0 { + /* 2. M.2 socket, CON14: pcie30phy port0 lane1, @fe170000 */ + max-link-speed = <3>; + num-lanes = <1>; + phys = <&pcie30phy>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_0_rst>; + reset-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_m2_b>; + status = "okay"; +}; + +&pcie2x1l1 { + /* 4. M.2 socket, CON16: pcie30phy port1 lane1, @fe180000 */ + max-link-speed = <3>; + num-lanes = <1>; + phys = <&pcie30phy>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_1_rst>; + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_m2_d>; + status = "okay"; +}; + +&pcie30phy { + /* + * Data lane mapping <1 3 2 4> = x1x1 x1x1 (bifurcation of both ports) + * port 0 lane 0 - always mapped to controller 0 (4L) + * port 0 lane 1 - map to controller 2 (1L0) + * port 1 lane 0 - map to controller 1 (2L) + * port 1 lane 1 - map to controller 3 (1L1) + */ + data-lanes = <1 3 2 4>; + status = "okay"; +}; + +&pcie3x4 { + /* 1. M.2 socket, CON13: pcie30phy port0 lane0, @fe150000 */ + max-link-speed = <3>; + num-lanes = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie3x4_rst>; + reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_m2_a>; + status = "okay"; +}; + +&pcie3x2 { + /* 3. M.2 socket, CON15: pcie30phy port1 lane0, @fe160000 */ + max-link-speed = <3>; + num-lanes = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie3x2_rst>; + reset-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_m2_c>; + status = "okay"; +}; + +&pinctrl { + audio { + headphone_detect: headphone-detect { + rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + gpio-key { + key1_pin: key1-pin { + rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + pcie { + pcie2_0_rst: pcie2-0-rst { + rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie2_1_rst: pcie2-1-rst { + rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie3x2_rst: pcie3x2-rst { + rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie3x4_rst: pcie3x4-rst { + rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb { + vcc_5v0_host20_en: vcc-5v0-host20-en { + rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc_5v0_host30p1_en: vcc-5v0-host30p1-en { + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc_5v0_host30p2_en: vcc-5v0-host30p2-en { + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb-typec { + usbc0_int: usbc0-int { + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + typec_5v_pwr_en: typec-5v-pwr-en { + rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +/* Connected to 5V Fan */ +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm1m1_pins>; + status = "okay"; +}; + +/* Connected to MIPI-DSI0 */ +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm2m1_pins>; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with UART0 */ +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm4m1_pins>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +&pwm5 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm5m1_pins>; + status = "okay"; +}; + +/* Buzzer */ +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm8m0_pins>; + status = "okay"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +&pwm9 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm9m0_pins>; + status = "okay"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with SPI4 */ +&pwm10 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm10m0_pins>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with UART3 */ +&pwm12 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm12m0_pins>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with UART3 */ +&pwm13 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm13m0_pins>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +&pwm14 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm14m0_pins>; + status = "okay"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Optimized for infrared applications */ +&pwm15 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm15m0_pins>; + status = "disabled"; +}; + +/* microSD card */ +&sdmmc { + status = "okay"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with UART4, UART7 and PWM10 */ +&spi0 { + num-cs = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0m2_cs0 &spi0m2_pins>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with UART8 */ +&spi4 { + num-cs = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&spi4m1_cs0 &spi4m1_pins>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with PWM4 */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0m0_xfer>; + status = "disabled"; +}; + +/* Debug UART */ +&uart2 { + status = "okay"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with PWM12 and PWM13 */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3m1_xfer>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with SPI0 */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4m2_xfer>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +&uart6 { + pinctrl-names = "default"; + pinctrl-0 = <&uart6m1_xfer>; + status = "okay"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with SPI0 */ +&uart7 { + pinctrl-names = "default"; + pinctrl-0 = <&uart7m2_xfer>; + status = "disabled"; +}; + +/* GPIO Connector, connected to 40-pin GPIO header */ +/* Shared with SPI4 */ +&uart8 { + pinctrl-names = "default"; + pinctrl-0 = <&uart8m1_xfer>; + status = "disabled"; +}; + +/* USB2 PHY for USB Type-C port */ +/* CM3588 USB Controller Config Table: USB20 OTG0 */ +&u2phy0 { + status = "okay"; +}; + +&u2phy0_otg { + phy-supply = <&vbus_5v0_typec>; + status = "okay"; +}; + +/* USB2 PHY for USB 3.0 Type-A port 1 */ +/* CM3588 USB Controller Config Table: USB20 OTG1 */ +&u2phy1 { + status = "okay"; +}; + +&u2phy1_otg { + phy-supply = <&vcc_5v0_host_30_p1>; + status = "okay"; +}; + +/* USB2 PHY for USB 2.0 Type-A */ +/* CM3588 USB Controller Config Table: USB20 HOST0 */ +&u2phy2 { + status = "okay"; +}; + +&u2phy2_host { + phy-supply = <&vcc_5v0_host_20>; + status = "okay"; +}; + +/* USB2 PHY for USB 3.0 Type-A port 2 */ +/* CM3588 USB Controller Config Table: USB20 HOST1 */ +&u2phy3 { + status = "okay"; +}; + +&u2phy3_host { + phy-supply = <&vcc_5v0_host_30_p2>; + status = "okay"; +}; + +/* USB 2.0 Type-A */ +/* PHYs: <&u2phy2_host> */ +&usb_host0_ehci { + status = "okay"; +}; + +/* USB 2.0 Type-A */ +/* PHYs: <&u2phy2_host> */ +&usb_host0_ohci { + status = "okay"; +}; + +/* USB Type-C */ +/* PHYs: <&u2phy0_otg>, <&usbdp_phy0 PHY_TYPE_USB3> */ +&usb_host0_xhci { + usb-role-switch; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + dwc3_0_role_switch: endpoint@0 { + reg = <0>; + remote-endpoint = <&usbc0_role_sw>; + }; + }; +}; + +/* Lower USB 3.0 Type-A (port 2) */ +/* PHYs: <&u2phy3_host> */ +&usb_host1_ehci { + status = "okay"; +}; + +/* Lower USB 3.0 Type-A (port 2) */ +/* PHYs: <&u2phy3_host> */ +&usb_host1_ohci { + status = "okay"; +}; + +/* Upper USB 3.0 Type-A (port 1) */ +/* PHYs: <&u2phy1_otg>, <&usbdp_phy1 PHY_TYPE_USB3> */ +&usb_host1_xhci { + dr_mode = "host"; + status = "okay"; +}; + +/* Lower USB 3.0 Type-A (port 2) */ +/* PHYs: <&combphy2_psu PHY_TYPE_USB3> */ +&usb_host2_xhci { + status = "okay"; +}; + +/* USB3 PHY for USB Type-C port */ +/* CM3588 USB Controller Config Table: USB30 OTG0 */ +&usbdp_phy0 { + orientation-switch; + sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>; + sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + usbdp_phy0_orientation_switch: endpoint@0 { + reg = <0>; + remote-endpoint = <&usbc0_orien_sw>; + }; + + usbdp_phy0_dp_altmode_mux: endpoint@1 { + reg = <1>; + remote-endpoint = <&dp_altmode_mux>; + }; + }; +}; + +/* USB3 PHY for USB 3.0 Type-A port 1 */ +/* CM3588 USB Controller Config Table: USB30 OTG1 */ +&usbdp_phy1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi new file mode 100644 index 000000000000..b1062380b4f2 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi @@ -0,0 +1,655 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2021 Rockchip Electronics Co., Ltd. + * Copyright (c) 2023 Thomas McKahan + * Copyright (c) 2024 Sebastian Kropatsch + * + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include "rk3588.dtsi" + +/ { + model = "FriendlyElec CM3588"; + compatible = "friendlyarm,cm3588", "rockchip,rk3588"; + + aliases { + mmc0 = &sdhci; + mmc1 = &sdmmc; + }; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + leds { + compatible = "gpio-leds"; + + led_sys: led-0 { + color = <LED_COLOR_ID_AMBER>; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpio2 RK_PC5 GPIO_ACTIVE_HIGH>; + label = "system-led"; + linux,default-trigger = "heartbeat"; + pinctrl-names = "default"; + pinctrl-0 = <&led_sys_pin>; + }; + + led_usr: led-1 { + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; + label = "user-led"; + pinctrl-names = "default"; + pinctrl-0 = <&led_usr_pin>; + }; + }; + + /* vcc_4v0_sys powers the RK806 and RK860's */ + vcc_4v0_sys: regulator-vcc-4v0-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc_4v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <4000000>; + }; + + vcc_3v3_pcie20: regulator-vcc-3v3-pcie20 { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_pcie20"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3_s3>; + }; + + vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 { + compatible = "regulator-fixed"; + gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sd_s0_pwr>; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "vcc_3v3_sd_s0"; + vin-supply = <&vcc_3v3_s3>; + }; + + vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 { + compatible = "regulator-fixed"; + regulator-name = "vcc-1v1-nldo-s3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + vin-supply = <&vcc_4v0_sys>; + }; +}; + +/* Combo PHY 0 is configured to act as as PCIe 2.0 PHY */ +/* Used by PCIe controller 4 (pcie2x1l2) */ +&combphy0_ps { + status = "okay"; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_l1 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_l2 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_l3 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_b0 { + cpu-supply = <&vdd_cpu_big0_s0>; +}; + +&cpu_b1 { + cpu-supply = <&vdd_cpu_big0_s0>; +}; + +&cpu_b2 { + cpu-supply = <&vdd_cpu_big1_s0>; +}; + +&cpu_b3 { + cpu-supply = <&vdd_cpu_big1_s0>; +}; + +&gpu { + mali-supply = <&vdd_gpu_s0>; + sram-supply = <&vdd_gpu_mem_s0>; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0m2_xfer>; + status = "okay"; + + vdd_cpu_big0_s0: regulator@42 { + compatible = "rockchip,rk8602"; + reg = <0x42>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu_big0_s0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1050000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc_4v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_cpu_big1_s0: regulator@43 { + compatible = "rockchip,rk8603", "rockchip,rk8602"; + reg = <0x43>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu_big1_s0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1050000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc_4v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; +}; + +&i2c2 { + status = "okay"; + + vdd_npu_s0: regulator@42 { + compatible = "rockchip,rk8602"; + reg = <0x42>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_npu_s0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc_4v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; +}; + +&i2c6 { + clock-frequency = <200000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c6m0_xfer>; + status = "okay"; + + hym8563: rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-output-names = "hym8563"; + interrupt-parent = <&gpio0>; + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&hym8563_int>; + wakeup-source; + }; +}; + +&i2c7 { + clock-frequency = <200000>; + status = "okay"; + + rt5616: audio-codec@1b { + compatible = "realtek,rt5616"; + reg = <0x1b>; + #sound-dai-cells = <0>; + }; +}; + +&i2s0_8ch { + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_lrck + &i2s0_mclk + &i2s0_sclk + &i2s0_sdi0 + &i2s0_sdo0>; + status = "okay"; +}; + +&i2s5_8ch { + status = "okay"; +}; + +&i2s6_8ch { + status = "okay"; +}; + +&i2s7_8ch { + status = "okay"; +}; + +&pcie2x1l2 { + /* r8125 ethernet, @fe190000 */ + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_2_rst>; + reset-gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_pcie20>; + status = "okay"; +}; + +&pinctrl { + gpio-leds { + led_sys_pin: led-sys-pin { + rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + led_usr_pin: led-usr-pin { + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hym8563 { + hym8563_int: hym8563-int { + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + pcie { + pcie2_2_rst: pcie2-2-rst { + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + sd_s0_pwr: sd-s0-pwr { + rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; + +&saradc { + vref-supply = <&avcc_1v8_s0>; + status = "okay"; +}; + +/* eMMC */ +&sdhci { + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + no-sd; + no-sdio; + non-removable; + vmmc-supply = <&vcc_3v3_s3>; + vqmmc-supply = <&vcc_1v8_s3>; + status = "okay"; +}; + +/* microSD card */ +&sdmmc { + bus-width = <4>; + cap-sd-highspeed; + disable-wp; + max-frequency = <150000000>; + no-mmc; + no-sdio; + sd-uhs-sdr104; + vmmc-supply = <&vcc_3v3_sd_s0>; + vqmmc-supply = <&vccio_sd_s0>; +}; + +&spi2 { + assigned-clocks = <&cru CLK_SPI2>; + assigned-clock-rates = <200000000>; + num-cs = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>; + status = "okay"; + + rk806_single: pmic@0 { + compatible = "rockchip,rk806"; + reg = <0x0>; + + interrupt-parent = <&gpio0>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, + <&rk806_dvs2_null>, <&rk806_dvs3_null>; + + spi-max-frequency = <1000000>; + + system-power-controller; + + vcc1-supply = <&vcc_4v0_sys>; + vcc2-supply = <&vcc_4v0_sys>; + vcc3-supply = <&vcc_4v0_sys>; + vcc4-supply = <&vcc_4v0_sys>; + vcc5-supply = <&vcc_4v0_sys>; + vcc6-supply = <&vcc_4v0_sys>; + vcc7-supply = <&vcc_4v0_sys>; + vcc8-supply = <&vcc_4v0_sys>; + vcc9-supply = <&vcc_4v0_sys>; + vcc10-supply = <&vcc_4v0_sys>; + vcc11-supply = <&vcc_2v0_pldo_s3>; + vcc12-supply = <&vcc_4v0_sys>; + vcc13-supply = <&vcc_1v1_nldo_s3>; + vcc14-supply = <&vcc_1v1_nldo_s3>; + vcca-supply = <&vcc_4v0_sys>; + + gpio-controller; + #gpio-cells = <2>; + + rk806_dvs1_null: dvs1-null-pins { + pins = "gpio_pwrctrl1"; + function = "pin_fun0"; + }; + + rk806_dvs2_null: dvs2-null-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun0"; + }; + + rk806_dvs3_null: dvs3-null-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun0"; + }; + + regulators { + vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 { + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_gpu_s0"; + regulator-enable-ramp-delay = <400>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_cpu_lit_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_log_s0: dcdc-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <750000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_log_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <750000>; + }; + }; + + vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_vdenc_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_ddr_s0: dcdc-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <900000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_ddr_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <850000>; + }; + }; + + vdd2_ddr_s3: dcdc-reg6 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vdd2_ddr_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_2v0_pldo_s3: dcdc-reg7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_2v0_pldo_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2000000>; + }; + }; + + vcc_3v3_s3: dcdc-reg8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_3v3_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vddq_ddr_s0: dcdc-reg9 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vddq_ddr_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8_s3: dcdc-reg10 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_1v8_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + avcc_1v8_s0: pldo-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "avcc_1v8_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8_s0: pldo-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_1v8_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + avdd_1v2_s0: pldo-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "avdd_1v2_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_3v3_s0: pldo-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <12500>; + regulator-name = "vcc_3v3_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd_s0: pldo-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <12500>; + regulator-name = "vccio_sd_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + pldo6_s3: pldo-reg6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "pldo6_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd_0v75_s3: nldo-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-name = "vdd_0v75_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <750000>; + }; + }; + + vdd_ddr_pll_s0: nldo-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-name = "vdd_ddr_pll_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <850000>; + }; + }; + + avdd_0v75_s0: nldo-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-name = "avdd_0v75_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_0v85_s0: nldo-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-name = "vdd_0v85_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_0v75_s0: nldo-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-name = "vdd_0v75_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&tsadc { + status = "okay"; +}; + +/* Debug UART */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2m0_xfer>; +};
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board. To reflect the hardware setup, add device tree sources for the SoM and the NAS daughter board as separate files. Hardware features: - Rockchip RK3588 SoC - 4GB/8GB/16GB LPDDR4x RAM - 64GB eMMC - MicroSD card slot - 1x RTL8125B 2.5G Ethernet - 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs - 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A - 1x USB 3.0 Type-C with DP AltMode support - 2x HDMI 2.1 out, 1x HDMI in - MIPI-CSI Connector, MIPI-DSI Connector - 40-pin GPIO header - 4 buttons: power, reset, recovery, MASK, user button - 3.5mm Headphone out, 2.0mm PH-2A Mic in - 5V Fan connector, PWM buzzer, IR receiver, RTC battery connector PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1 speed. Data lane mapping in the DT is done like described in commit f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588"). This device tree includes support for eMMC, SD card, ethernet, all USB2 and USB3 ports, all four M.2 slots, GPU, RTC, buzzer, UART debugging as well as the buttons and LEDs. The GPIOs are labeled according to the schematics. Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de> --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../rk3588-friendlyelec-cm3588-nas.dts | 759 ++++++++++++++++++ .../rockchip/rk3588-friendlyelec-cm3588.dtsi | 655 +++++++++++++++ 3 files changed, 1415 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-friendlyelec-cm3588.dtsi