new file mode 100644
@@ -0,0 +1,45 @@
+What: /sys/bus/iio/devices/iio:deviceX/resolution_bits
+KernelVersion: 6.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ ADC measurement resolution. Can be either 11 bits or 14 bits
+ (default). The driver sets the same resolution for both VBUS and
+ VSENSE measurements even if the hardware could be configured to
+ measure VBUS and VSENSE with different resolutions.
+ This attribute affects the integration time: with 14 bits
+ resolution the integration time is increased by a factor of
+ 1.9 (the driver considers a factor of 2). See Table 4-5 in
+ device datasheet for details.
+
+What: /sys/bus/iio/devices/iio:deviceX/resolution_bits_available
+KernelVersion: 6.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ List all possible ADC measurement resolutions: "11 14"
+
+What: /sys/bus/iio/devices/iio:deviceX/integration_samples
+KernelVersion: 6.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ Number of samples taken during a full integration period. Can be
+ set to any power of 2 value from 1 (default) to 2048.
+ This attribute affects the integration time: higher the number
+ of samples, longer the integration time. See Table 4-5 in device
+ datasheet for details.
+
+What: /sys/bus/iio/devices/iio:deviceX/integration_samples_available
+KernelVersion: 6.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ List all possible numbers of integration samples:
+ "1 2 4 8 16 32 64 128 256 512 1024 2048"
+
+What: /sys/bus/iio/devices/iio:devices/filters_en
+KernelVersion: 6.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ Attribute to enable/disable ADC post filters. Enabled by
+ default.
+ This attribute affects the integration time: with filters
+ enabled the integration time is increased by 50%. See Table 4-5
+ in device datasheet for details.
@@ -14793,6 +14793,13 @@ F: Documentation/devicetree/bindings/nvmem/microchip,sama7g5-otpc.yaml
F: drivers/nvmem/microchip-otpc.c
F: include/dt-bindings/nvmem/microchip,sama7g5-otpc.h
+MICROCHIP PAC1921 POWER/CURRENT MONITOR DRIVER
+M: Matteo Martelli <matteomartelli3@gmail.com>
+L: linux-iio@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/iio/adc/microchip,pac1921.yaml
+F: drivers/iio/adc/pac1921.c
+
MICROCHIP PAC1934 POWER/ENERGY MONITOR DRIVER
M: Marius Cristea <marius.cristea@microchip.com>
L: linux-iio@vger.kernel.org
@@ -991,6 +991,16 @@ config NPCM_ADC
This driver can also be built as a module. If so, the module
will be called npcm_adc.
+config PAC1921
+ tristate "Microchip Technology PAC1921 driver"
+ depends on I2C
+ help
+ Say yes here to build support for Microchip Technology's PAC1921
+ High-Side Power/Current Monitor with Analog Output.
+
+ This driver can also be built as a module. If so, the module
+ will be called pac1921.
+
config PAC1934
tristate "Microchip Technology PAC1934 driver"
depends on I2C
@@ -90,6 +90,7 @@ obj-$(CONFIG_MP2629_ADC) += mp2629_adc.o
obj-$(CONFIG_MXS_LRADC_ADC) += mxs-lradc-adc.o
obj-$(CONFIG_NAU7802) += nau7802.o
obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
+obj-$(CONFIG_PAC1921) += pac1921.o
obj-$(CONFIG_PAC1934) += pac1934.o
obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
new file mode 100644
@@ -0,0 +1,1033 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * IIO driver for PAC1921 High-Side Power/Current Monitor
+ *
+ * Copyright (C) 2024 Matteo Martelli <matteomartelli3@gmail.com>
+ */
+
+#include <linux/i2c.h>
+#include <linux/iio/events.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/regmap.h>
+
+/* pac1921 registers */
+#define PAC1921_REG_GAIN_CFG 0x00
+#define PAC1921_REG_INT_CFG 0x01
+#define PAC1921_REG_CONTROL 0x02
+#define PAC1921_REG_VBUS 0x10
+#define PAC1921_REG_VSENSE 0x12
+#define PAC1921_REG_OVERFLOW_STS 0x1C
+#define PAC1921_REG_VPOWER 0x1D
+
+/* pac1921 gain configuration bits */
+#define PAC1921_GAIN_I_RES BIT(7)
+#define PAC1921_GAIN_V_RES BIT(6)
+#define PAC1921_GAIN_DI_GAIN_SHIFT 3
+#define PAC1921_GAIN_DI_GAIN_MASK GENMASK(5, PAC1921_GAIN_DI_GAIN_SHIFT)
+#define PAC1921_GAIN_DI_GAIN_MAX 7
+#define PAC1921_GAIN_DV_GAIN_SHIFT 0
+#define PAC1921_GAIN_DV_GAIN_MASK GENMASK(2, PAC1921_GAIN_DV_GAIN_SHIFT)
+#define PAC1921_GAIN_DV_GAIN_MAX 5
+
+/* pac1921 integration configuration bits */
+#define PAC1921_INT_CFG_SMPL_SHIFT 4
+#define PAC1921_INT_CFG_SMPL_MASK GENMASK(7, PAC1921_INT_CFG_SMPL_SHIFT)
+#define PAC1921_INT_CFG_SMPL_MAX 11
+#define PAC1921_INT_CFG_VSFEN BIT(3)
+#define PAC1921_INT_CFG_VBFEN BIT(2)
+#define PAC1921_INT_CFG_RIOV BIT(1)
+#define PAC1921_INT_CFG_INTEN BIT(0)
+
+/* pac1921 control bits */
+#define PAC1921_CONTROL_MXSL_SHIFT 6
+enum pac1921_mxsl {
+ PAC1921_MXSL_VPOWER_PIN = 0,
+ PAC1921_MXSL_VSENSE_FREE_RUN = 1,
+ PAC1921_MXSL_VBUS_FREE_RUN = 2,
+ PAC1921_MXSL_VPOWER_FREE_RUN = 3,
+};
+#define PAC1921_CONTROL_SLEEP BIT(2)
+
+/* pac1921 overflow status bits */
+#define PAC1921_OVERFLOW_VSOV BIT(2)
+#define PAC1921_OVERFLOW_VBOV BIT(1)
+#define PAC1921_OVERFLOW_VPOV BIT(0)
+
+/* pac1921 constants */
+#define PAC1921_MAX_VSENSE_MV 100
+#define PAC1921_MAX_VBUS_V 32
+#define PAC1921_RES_RESOLUTION 1023 /* Result registers resolution */
+
+/* pac1921 defaults */
+#define PAC1921_DEFAULT_DV_GAIN 0 /* 2^(value): 1x gain */
+#define PAC1921_DEFAULT_DI_GAIN 0 /* 2^(value): 1x gain */
+#define PAC1921_DEFAULT_HIGH_RES true /* 14-bit measurement resolution */
+#define PAC1921_DEFAULT_NUM_SAMPLES 0 /* 2^(value): 1 sample */
+#define PAC1921_DEFAULT_FILTERS_ENABLED true
+
+/* pac1921 tables to create iio available parameters */
+static const unsigned int pac1921_di_gains[] = { 1, 2, 4, 8, 16, 32, 64, 128 };
+static const unsigned int pac1921_dv_gains[] = { 1, 2, 4, 8, 16, 32 };
+enum pac1921_meas_resolution_idx {
+ PAC1921_MEAS_RESOLUTION_IDX_LOW = 0,
+ PAC1921_MEAS_RESOLUTION_IDX_HIGH,
+};
+static const char *const pac1921_meas_resolutions[] = { "11", "14" };
+static const char *const pac1921_integr_num_samples[] = {
+ "1", "2", "4", "8", "16", "32",
+ "64", "128", "256", "512", "1024", "2048"
+};
+
+/* pac1921 regmap configuration */
+static const struct regmap_range pac1921_regmap_wr_ranges[] = {
+ regmap_reg_range(PAC1921_REG_GAIN_CFG, PAC1921_REG_CONTROL),
+};
+static const struct regmap_access_table pac1921_regmap_wr_table = {
+ .yes_ranges = pac1921_regmap_wr_ranges,
+ .n_yes_ranges = ARRAY_SIZE(pac1921_regmap_wr_ranges),
+};
+static const struct regmap_range pac1921_regmap_rd_ranges[] = {
+ regmap_reg_range(PAC1921_REG_GAIN_CFG, PAC1921_REG_CONTROL),
+ regmap_reg_range(PAC1921_REG_VBUS, PAC1921_REG_VPOWER + 1),
+};
+static const struct regmap_access_table pac1921_regmap_rd_table = {
+ .yes_ranges = pac1921_regmap_rd_ranges,
+ .n_yes_ranges = ARRAY_SIZE(pac1921_regmap_rd_ranges),
+};
+static const struct regmap_config pac1921_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = &pac1921_regmap_rd_table,
+ .wr_table = &pac1921_regmap_wr_table,
+};
+
+enum pac1921_channels {
+ PAC1921_CHAN_VBUS = 0,
+ PAC1921_CHAN_VSENSE = 1,
+ PAC1921_CHAN_CURRENT = 2,
+ PAC1921_CHAN_POWER = 3,
+};
+#define PAC1921_NUM_MEAS_CHANS 4
+
+struct pac1921_priv {
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct iio_info iio_info;
+
+ /* Synchronize access to private members, and ensure atomicity of
+ * consecutive regmap operations.
+ */
+ struct mutex lock;
+
+ u32 rshunt; /* uOhm */
+ bool high_res;
+ u8 dv_gain;
+ u8 di_gain;
+ u8 n_samples;
+ bool filters_en;
+ u8 prev_ovf_flags;
+
+ bool first_integr_started;
+ bool first_integr_done;
+ unsigned long integr_start_time; /* jiffies */
+ unsigned int integr_period; /* usecs */
+
+ struct {
+ u16 chan[PAC1921_NUM_MEAS_CHANS];
+ s64 timestamp __aligned(8);
+ } scan;
+};
+
+/* The integration period depends on the configuration of number of integration
+ * samples, measurement resolution and post filters. The following array
+ * contains integration periods, in microsecs unit, based on table 4-5 from
+ * datasheet considering power integration mode, 11-Bit resolution and post
+ * filters off. Each index corresponds to a specific number of samples from 1
+ * to 2048.
+ */
+static const unsigned int pac1921_integr_periods_us[] = {
+ 930, 1460, 2410, 4320, 8050, 16100,
+ 32100, 64200, 128300, 257000, 513000, 1026000
+};
+
+/* Calculate and update the integration period
+ *
+ * The base integration period is retrieved from pac1921_integr_periods_us
+ * array, then doubled if 14-Bit resolution is used (even if the actual
+ * increase factor is about 1.9) and increased by 50% if post filters are
+ * enabled.
+ *
+ * Must be called with lock held.
+ */
+static int pac1921_update_integr_period(struct pac1921_priv *priv)
+{
+ if (WARN_ON_ONCE(priv->n_samples >=
+ ARRAY_SIZE(pac1921_integr_periods_us)))
+ return -EINVAL;
+
+ priv->integr_period = pac1921_integr_periods_us[priv->n_samples];
+ if (priv->high_res)
+ priv->integr_period *= 2;
+ if (priv->filters_en)
+ priv->integr_period += priv->integr_period / 2;
+
+ return 0;
+}
+
+/* Check if first integration after configuration update has completed.
+ *
+ * Must be called with lock held.
+ */
+static bool pac1921_data_ready(struct pac1921_priv *priv)
+{
+ if (!priv->first_integr_started)
+ return false;
+
+ if (!priv->first_integr_done) {
+ unsigned long t_ready = priv->integr_start_time +
+ usecs_to_jiffies(priv->integr_period);
+ if (time_before(jiffies, t_ready))
+ /* First integration not completed: data not ready */
+ return false;
+
+ priv->first_integr_done = true;
+ }
+
+ return true;
+}
+
+/* Check if overflow occurred and if so, push the corresponding events.
+ *
+ * Must be called with lock held.
+ */
+static int pac1921_check_push_overflow(struct iio_dev *indio_dev, s64 timestamp)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+ unsigned int flags;
+
+ int ret = regmap_read(priv->regmap, PAC1921_REG_OVERFLOW_STS, &flags);
+ if (ret)
+ return ret;
+
+ if (flags & PAC1921_OVERFLOW_VBOV &&
+ !(priv->prev_ovf_flags & PAC1921_OVERFLOW_VBOV)) {
+ iio_push_event(indio_dev,
+ IIO_UNMOD_EVENT_CODE(
+ IIO_VOLTAGE, PAC1921_CHAN_VBUS,
+ IIO_EV_TYPE_THRESH, IIO_EV_DIR_RISING),
+ timestamp);
+ }
+ if (flags & PAC1921_OVERFLOW_VSOV &&
+ !(priv->prev_ovf_flags & PAC1921_OVERFLOW_VSOV)) {
+ iio_push_event(indio_dev,
+ IIO_UNMOD_EVENT_CODE(
+ IIO_VOLTAGE, PAC1921_CHAN_VSENSE,
+ IIO_EV_TYPE_THRESH, IIO_EV_DIR_RISING),
+ timestamp);
+ iio_push_event(indio_dev,
+ IIO_UNMOD_EVENT_CODE(
+ IIO_CURRENT, PAC1921_CHAN_CURRENT,
+ IIO_EV_TYPE_THRESH, IIO_EV_DIR_RISING),
+ timestamp);
+ }
+ if (flags & PAC1921_OVERFLOW_VPOV &&
+ !(priv->prev_ovf_flags & PAC1921_OVERFLOW_VPOV)) {
+ iio_push_event(indio_dev,
+ IIO_UNMOD_EVENT_CODE(
+ IIO_POWER, PAC1921_CHAN_POWER,
+ IIO_EV_TYPE_THRESH, IIO_EV_DIR_RISING),
+ timestamp);
+ }
+
+ priv->prev_ovf_flags = (u8)flags;
+
+ return 0;
+}
+
+/* Read the value from a result register
+ *
+ * Result registers contain the most recent averaged values of Vbus, Vsense and
+ * Vpower. Each value is 10 bits wide and spread across two consecutive 8 bit
+ * registers, with 6 bit LSB zero padding.
+ */
+static int pac1921_read_res(struct pac1921_priv *priv, unsigned long reg,
+ int *val)
+{
+ u8 val_buf[2];
+
+ int ret = regmap_bulk_read(priv->regmap, (unsigned int)reg, &val_buf,
+ sizeof(val_buf));
+ if (ret)
+ return ret;
+
+ *val = (val_buf[0] << 8 | val_buf[1]) >> 6;
+
+ return 0;
+}
+
+/* Get the Vsense LSB in nV
+ *
+ * Used to calculate scale factors for current and power measurements
+ */
+static inline int pac1921_vsense_lsb(u8 di_gain)
+{
+ int max = (PAC1921_MAX_VSENSE_MV * 1000000) >> (int)di_gain;
+
+ return DIV_ROUND_CLOSEST(max, PAC1921_RES_RESOLUTION);
+}
+
+static int pac1921_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int *val,
+ int *val2, long mask)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW: {
+ guard(mutex)(&priv->lock);
+
+ if (!pac1921_data_ready(priv))
+ return -EBUSY;
+
+ s64 ts = iio_get_time_ns(indio_dev);
+
+ int ret = pac1921_check_push_overflow(indio_dev, ts);
+ if (ret)
+ return ret;
+
+ ret = pac1921_read_res(priv, chan->address, val);
+ if (ret)
+ return ret;
+
+ return IIO_VAL_INT;
+ }
+ case IIO_CHAN_INFO_SCALE:
+ switch (chan->channel) {
+ case PAC1921_CHAN_VBUS: {
+ /* Vbus scale factor in mV:
+ * max_vbus (mV) / vgain / resolution
+ */
+ guard(mutex)(&priv->lock);
+
+ *val = PAC1921_MAX_VBUS_V * 1000;
+ *val2 = PAC1921_RES_RESOLUTION << (int)priv->dv_gain;
+
+ return IIO_VAL_FRACTIONAL;
+ }
+ case PAC1921_CHAN_VSENSE: {
+ /* Vsense voltage scale factor in mV:
+ * max_vsense (mV) / igain / resolution
+ */
+ guard(mutex)(&priv->lock);
+
+ *val = PAC1921_MAX_VSENSE_MV;
+ *val2 = PAC1921_RES_RESOLUTION << (int)priv->di_gain;
+
+ return IIO_VAL_FRACTIONAL;
+ }
+ case PAC1921_CHAN_CURRENT: {
+ /* Current scale factor in mA:
+ * Vsense LSB (nV) / shunt (uOhm)
+ */
+ guard(mutex)(&priv->lock);
+
+ *val = pac1921_vsense_lsb(priv->di_gain);
+ *val2 = (int)priv->rshunt;
+
+ return IIO_VAL_FRACTIONAL;
+ }
+ case PAC1921_CHAN_POWER: {
+ /* Power scale factor in mW:
+ * Vsense LSB (nV) * max_vbus (V) / vgain / shunt (uOhm)
+ */
+ guard(mutex)(&priv->lock);
+
+ *val = pac1921_vsense_lsb(priv->di_gain) *
+ (PAC1921_MAX_VBUS_V >> (int)priv->dv_gain);
+ *val2 = (int)priv->rshunt;
+
+ return IIO_VAL_FRACTIONAL;
+ }
+ default:
+ return -EINVAL;
+ }
+ break;
+
+ case IIO_CHAN_INFO_HARDWAREGAIN:
+ switch (chan->channel) {
+ case PAC1921_CHAN_VBUS: {
+ guard(mutex)(&priv->lock);
+ *val = 1 << (int)priv->dv_gain;
+ return IIO_VAL_INT;
+ }
+ case PAC1921_CHAN_VSENSE:
+ case PAC1921_CHAN_CURRENT: {
+ guard(mutex)(&priv->lock);
+ *val = 1 << (int)priv->di_gain;
+ return IIO_VAL_INT;
+ }
+ default:
+ return -EINVAL;
+ }
+
+ case IIO_CHAN_INFO_INT_TIME: {
+ /* Integration time is read only: it depends on the number of
+ * integration samples, measurement resolution and post filters
+ */
+ *val2 = 1000000; /* From usecs to fractional secs */
+ guard(mutex)(&priv->lock);
+ *val = (int)priv->integr_period;
+ return IIO_VAL_FRACTIONAL;
+ }
+ default:
+ return -EINVAL;
+ }
+}
+
+/* Perform configuration update sequence: set the device into read state, then
+ * write the config register and set the device back into integration state.
+ * Also reset integration start time and mark first integration to be yet
+ * completed.
+ *
+ * Must be called with lock held.
+ */
+static int pac1921_update_cfg_reg(struct pac1921_priv *priv, unsigned int reg,
+ unsigned int mask, unsigned int val)
+{
+ /* Enter READ state before configuration */
+ int ret = regmap_update_bits(priv->regmap, PAC1921_REG_INT_CFG,
+ PAC1921_INT_CFG_INTEN, 0);
+ if (ret)
+ return ret;
+
+ /* Update configuration value */
+ ret = regmap_update_bits(priv->regmap, reg, mask, val);
+ if (ret)
+ return ret;
+
+ /* Re-enable integration and reset start time */
+ ret = regmap_update_bits(priv->regmap, PAC1921_REG_INT_CFG,
+ PAC1921_INT_CFG_INTEN, PAC1921_INT_CFG_INTEN);
+ if (ret)
+ return ret;
+
+ priv->integr_start_time = jiffies;
+ priv->first_integr_done = false;
+
+ return 0;
+}
+
+static inline bool pac1921_gain_param_valid(unsigned int gain, unsigned int max)
+{
+ return (gain > 0 && gain <= (1U << max) && is_power_of_2(gain));
+}
+
+static int pac1921_update_gain(struct pac1921_priv *priv,
+ struct iio_chan_spec const *chan, int val)
+{
+ unsigned int max;
+ unsigned int mask;
+ unsigned int shift;
+ u8 *priv_val;
+
+ switch (chan->channel) {
+ case PAC1921_CHAN_VBUS:
+ max = PAC1921_GAIN_DV_GAIN_MAX;
+ mask = PAC1921_GAIN_DV_GAIN_MASK;
+ shift = PAC1921_GAIN_DV_GAIN_SHIFT;
+ priv_val = &priv->dv_gain;
+ break;
+ case PAC1921_CHAN_VSENSE:
+ case PAC1921_CHAN_CURRENT:
+ max = PAC1921_GAIN_DI_GAIN_MAX;
+ mask = PAC1921_GAIN_DI_GAIN_MASK;
+ shift = PAC1921_GAIN_DI_GAIN_SHIFT;
+ priv_val = &priv->di_gain;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ unsigned int gain_param = (unsigned int)val;
+
+ if (!pac1921_gain_param_valid(gain_param, max))
+ return -EINVAL;
+
+ u8 gain = (u8)ilog2(gain_param);
+
+ guard(mutex)(&priv->lock);
+
+ if (*priv_val == gain)
+ return 0;
+
+ int ret = pac1921_update_cfg_reg(priv, PAC1921_REG_GAIN_CFG, mask,
+ gain << shift);
+ if (ret)
+ return ret;
+
+ *priv_val = gain;
+
+ return 0;
+}
+
+static int pac1921_write_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int val,
+ int val2, long mask)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ switch (mask) {
+ case IIO_CHAN_INFO_HARDWAREGAIN:
+ return pac1921_update_gain(priv, chan, val);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int pac1921_read_avail(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ const int **vals, int *type, int *length,
+ long mask)
+{
+ switch (mask) {
+ case IIO_CHAN_INFO_HARDWAREGAIN:
+ switch (chan->channel) {
+ case PAC1921_CHAN_VBUS:
+ *length = ARRAY_SIZE(pac1921_dv_gains);
+ *vals = pac1921_dv_gains;
+ *type = IIO_VAL_INT;
+ return IIO_AVAIL_LIST;
+
+ case PAC1921_CHAN_VSENSE:
+ case PAC1921_CHAN_CURRENT:
+ *length = ARRAY_SIZE(pac1921_di_gains);
+ *vals = pac1921_di_gains;
+ *type = IIO_VAL_INT;
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+ default:
+ return -EINVAL;
+ }
+}
+
+static int pac1921_read_label(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, char *label)
+{
+ switch (chan->channel) {
+ case PAC1921_CHAN_VBUS:
+ return sprintf(label, "vbus\n");
+ case PAC1921_CHAN_VSENSE:
+ return sprintf(label, "vsense\n");
+ case PAC1921_CHAN_CURRENT:
+ return sprintf(label, "current\n");
+ case PAC1921_CHAN_POWER:
+ return sprintf(label, "power\n");
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info pac1921_iio = {
+ .read_raw = pac1921_read_raw,
+ .write_raw = pac1921_write_raw,
+ .read_avail = pac1921_read_avail,
+ .read_label = pac1921_read_label,
+};
+
+static int pac1921_get_resolution(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ guard(mutex)(&priv->lock);
+
+ if (priv->high_res)
+ return PAC1921_MEAS_RESOLUTION_IDX_HIGH;
+
+ return PAC1921_MEAS_RESOLUTION_IDX_LOW;
+}
+
+static int pac1921_set_resolution(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ unsigned int val)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+ bool high_res;
+
+ switch (val) {
+ case PAC1921_MEAS_RESOLUTION_IDX_LOW:
+ high_res = false;
+ break;
+ case PAC1921_MEAS_RESOLUTION_IDX_HIGH:
+ high_res = true;
+ break;
+ default:
+ WARN_ON_ONCE(1);
+ return -EINVAL;
+ }
+
+ guard(mutex)(&priv->lock);
+
+ if (priv->high_res == high_res)
+ return 0;
+
+ unsigned int mask = PAC1921_GAIN_I_RES | PAC1921_GAIN_V_RES;
+ unsigned int bits = high_res ?
+ 0 : PAC1921_GAIN_I_RES | PAC1921_GAIN_V_RES;
+
+ int ret = pac1921_update_cfg_reg(priv, PAC1921_REG_GAIN_CFG,
+ mask, bits);
+ if (ret)
+ return ret;
+
+ priv->high_res = high_res;
+
+ return pac1921_update_integr_period(priv);
+}
+
+static int pac1921_get_int_num_samples(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ guard(mutex)(&priv->lock);
+
+ return priv->n_samples;
+}
+
+static int pac1921_set_int_num_samples(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ unsigned int val)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ if (WARN_ON_ONCE(val > PAC1921_INT_CFG_SMPL_MAX))
+ return -EINVAL;
+
+ guard(mutex)(&priv->lock);
+
+ if (priv->n_samples == val)
+ return 0;
+
+ int ret = pac1921_update_cfg_reg(priv, PAC1921_REG_INT_CFG,
+ PAC1921_INT_CFG_SMPL_MASK,
+ val << PAC1921_INT_CFG_SMPL_SHIFT);
+ if (ret)
+ return ret;
+
+ priv->n_samples = (u8)val;
+
+ return pac1921_update_integr_period(priv);
+}
+
+static ssize_t pac1921_read_filters_enabled(struct iio_dev *indio_dev,
+ uintptr_t private,
+ const struct iio_chan_spec *chan,
+ char *buf)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+ bool enabled;
+
+ scoped_guard(mutex, &priv->lock) {
+ enabled = priv->filters_en;
+ }
+ return sysfs_emit(buf, "%d\n", enabled);
+}
+
+static ssize_t pac1921_write_filters_enabled(struct iio_dev *indio_dev,
+ uintptr_t private,
+ const struct iio_chan_spec *chan,
+ const char *buf, size_t len)
+{
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+ bool enabled;
+
+ int ret = kstrtobool(buf, &enabled);
+ if (ret)
+ return ret;
+
+ guard(mutex)(&priv->lock);
+
+ if (priv->filters_en == enabled)
+ return 0;
+
+ unsigned int mask = PAC1921_INT_CFG_VSFEN | PAC1921_INT_CFG_VBFEN;
+ unsigned int bits = enabled ?
+ PAC1921_INT_CFG_VSFEN | PAC1921_INT_CFG_VBFEN : 0;
+
+
+ ret = pac1921_update_cfg_reg(priv, PAC1921_REG_INT_CFG, mask, bits);
+ if (ret)
+ return ret;
+
+ priv->filters_en = enabled;
+
+ ret = pac1921_update_integr_period(priv);
+ if (ret)
+ return ret;
+
+ return len;
+}
+
+static const struct iio_enum pac1921_resolution_enum = {
+ .items = pac1921_meas_resolutions,
+ .num_items = ARRAY_SIZE(pac1921_meas_resolutions),
+ .get = pac1921_get_resolution,
+ .set = pac1921_set_resolution,
+};
+static const struct iio_enum pac1921_int_num_samples_enum = {
+ .items = pac1921_integr_num_samples,
+ .num_items = ARRAY_SIZE(pac1921_integr_num_samples),
+ .get = pac1921_get_int_num_samples,
+ .set = pac1921_set_int_num_samples,
+};
+static const struct iio_chan_spec_ext_info pac1921_ext_info[] = {
+ IIO_ENUM("resolution_bits", IIO_SHARED_BY_ALL,
+ &pac1921_resolution_enum),
+ IIO_ENUM_AVAILABLE("resolution_bits", IIO_SHARED_BY_ALL,
+ &pac1921_resolution_enum),
+ IIO_ENUM("integration_samples", IIO_SHARED_BY_ALL,
+ &pac1921_int_num_samples_enum),
+ IIO_ENUM_AVAILABLE("integration_samples", IIO_SHARED_BY_ALL,
+ &pac1921_int_num_samples_enum),
+ {
+ .name = "filters_en",
+ .read = pac1921_read_filters_enabled,
+ .write = pac1921_write_filters_enabled,
+ .shared = IIO_SHARED_BY_ALL,
+ },
+ {},
+};
+
+static const struct iio_event_spec pac1921_overflow_event[] = {
+ {
+ .type = IIO_EV_TYPE_THRESH,
+ .dir = IIO_EV_DIR_RISING,
+ },
+};
+
+static const struct iio_chan_spec pac1921_channels[] = {
+ {
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE) |
+ BIT(IIO_CHAN_INFO_HARDWAREGAIN),
+ .info_mask_separate_available = BIT(IIO_CHAN_INFO_HARDWAREGAIN),
+ .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_INT_TIME),
+ .channel = PAC1921_CHAN_VBUS,
+ .address = PAC1921_REG_VBUS,
+ .scan_index = PAC1921_CHAN_VBUS,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 10,
+ .storagebits = 16,
+ .endianness = IIO_CPU
+ },
+ .indexed = 1,
+ .event_spec = pac1921_overflow_event,
+ .num_event_specs = ARRAY_SIZE(pac1921_overflow_event),
+ .ext_info = pac1921_ext_info,
+ },
+ {
+ .type = IIO_VOLTAGE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE) |
+ BIT(IIO_CHAN_INFO_HARDWAREGAIN),
+ .info_mask_separate_available = BIT(IIO_CHAN_INFO_HARDWAREGAIN),
+ .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_INT_TIME),
+ .channel = PAC1921_CHAN_VSENSE,
+ .address = PAC1921_REG_VSENSE,
+ .scan_index = PAC1921_CHAN_VSENSE,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 10,
+ .storagebits = 16,
+ .endianness = IIO_CPU
+ },
+ .indexed = 1,
+ .event_spec = pac1921_overflow_event,
+ .num_event_specs = ARRAY_SIZE(pac1921_overflow_event),
+ .ext_info = pac1921_ext_info,
+ },
+ {
+ .type = IIO_CURRENT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE) |
+ BIT(IIO_CHAN_INFO_HARDWAREGAIN),
+ .info_mask_separate_available = BIT(IIO_CHAN_INFO_HARDWAREGAIN),
+ .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_INT_TIME),
+ .channel = PAC1921_CHAN_CURRENT,
+ .address = PAC1921_REG_VSENSE,
+ .scan_index = PAC1921_CHAN_CURRENT,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 10,
+ .storagebits = 16,
+ .endianness = IIO_CPU
+ },
+ .event_spec = pac1921_overflow_event,
+ .num_event_specs = ARRAY_SIZE(pac1921_overflow_event),
+ .ext_info = pac1921_ext_info,
+ },
+ {
+ .type = IIO_POWER,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_INT_TIME),
+ .channel = PAC1921_CHAN_POWER,
+ .address = PAC1921_REG_VPOWER,
+ .scan_index = PAC1921_CHAN_POWER,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 10,
+ .storagebits = 16,
+ .endianness = IIO_CPU
+ },
+ .event_spec = pac1921_overflow_event,
+ .num_event_specs = ARRAY_SIZE(pac1921_overflow_event),
+ .ext_info = pac1921_ext_info,
+ },
+ IIO_CHAN_SOFT_TIMESTAMP(PAC1921_NUM_MEAS_CHANS),
+};
+
+static irqreturn_t pac1921_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *idev = pf->indio_dev;
+ struct pac1921_priv *priv = iio_priv(idev);
+
+ guard(mutex)(&priv->lock);
+
+ if (!pac1921_data_ready(priv))
+ goto done;
+
+ int ret = pac1921_check_push_overflow(idev, pf->timestamp);
+ if (ret)
+ goto done;
+
+ memset(&priv->scan, 0, sizeof(priv->scan));
+
+ int bit, ch = 0;
+ for_each_set_bit(bit, idev->active_scan_mask, idev->masklength) {
+ int val;
+
+ ret = pac1921_read_res(priv, idev->channels[ch].address, &val);
+ if (ret)
+ goto done;
+
+ priv->scan.chan[ch++] = (u16)val;
+ }
+
+ iio_push_to_buffers_with_timestamp(idev, &priv->scan, pf->timestamp);
+
+done:
+ iio_trigger_notify_done(idev->trig);
+
+ return IRQ_HANDLED;
+}
+
+static int pac1921_init(struct pac1921_priv *priv)
+{
+ /* Enter READ state before configuration */
+ int ret = regmap_update_bits(priv->regmap, PAC1921_REG_INT_CFG,
+ PAC1921_INT_CFG_INTEN, 0);
+ if (ret)
+ return ret;
+
+ /* Configure gains and measurements resolution */
+ unsigned int val = priv->di_gain << PAC1921_GAIN_DI_GAIN_SHIFT |
+ priv->dv_gain << PAC1921_GAIN_DV_GAIN_SHIFT;
+ if (!priv->high_res)
+ val |= PAC1921_GAIN_I_RES | PAC1921_GAIN_V_RES;
+ ret = regmap_write(priv->regmap, PAC1921_REG_GAIN_CFG, val);
+ if (ret)
+ return ret;
+
+ /* Configure integration:
+ * - num of integration samples, filters enabled/disabled
+ * - set READ/INT pin override (RIOV) to control operation mode via
+ * register instead of pin
+ */
+ val = priv->n_samples << PAC1921_INT_CFG_SMPL_SHIFT |
+ PAC1921_INT_CFG_RIOV;
+ if (priv->filters_en)
+ val |= PAC1921_INT_CFG_VSFEN | PAC1921_INT_CFG_VBFEN;
+ ret = regmap_write(priv->regmap, PAC1921_REG_INT_CFG, val);
+ if (ret)
+ return ret;
+
+ /* Init control register:
+ * - VPower free run integration mode
+ * - OUT pin full scale range: 3V (HW detault)
+ * - no timeout, no sleep, no sleep override, no recalc (HW defaults)
+ */
+ val = PAC1921_MXSL_VPOWER_FREE_RUN << PAC1921_CONTROL_MXSL_SHIFT;
+ ret = regmap_write(priv->regmap, PAC1921_REG_CONTROL, val);
+ if (ret)
+ return ret;
+
+ /* Enable integration */
+ ret = regmap_update_bits(priv->regmap, PAC1921_REG_INT_CFG,
+ PAC1921_INT_CFG_INTEN, PAC1921_INT_CFG_INTEN);
+ if (ret)
+ return ret;
+
+ priv->first_integr_started = true;
+ priv->integr_start_time = jiffies;
+
+ return pac1921_update_integr_period(priv);
+}
+
+static int pac1921_suspend(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ guard(mutex)(&priv->lock);
+
+ priv->first_integr_started = false;
+ priv->first_integr_done = false;
+
+ int ret = regmap_update_bits(priv->regmap, PAC1921_REG_INT_CFG,
+ PAC1921_INT_CFG_INTEN, 0);
+ if (ret)
+ return ret;
+
+ return regmap_update_bits(priv->regmap, PAC1921_REG_CONTROL,
+ PAC1921_CONTROL_SLEEP, PAC1921_CONTROL_SLEEP);
+}
+
+static int pac1921_resume(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct pac1921_priv *priv = iio_priv(indio_dev);
+
+ guard(mutex)(&priv->lock);
+
+ return pac1921_init(priv);
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(pac1921_pm_ops, pac1921_suspend,
+ pac1921_resume);
+
+static int pac1921_parse_properties(struct pac1921_priv *priv)
+{
+ struct device *dev = &priv->client->dev;
+ u32 prop;
+
+ int ret = device_property_read_u32(dev, "shunt-resistor-micro-ohms",
+ &prop);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Cannot read shunt resistor property\n");
+ if (prop == 0 || prop > INT_MAX)
+ return dev_err_probe(dev, -EINVAL,
+ "Invalid shunt resistor: %u\n", prop);
+ priv->rshunt = prop;
+
+ if (!device_property_read_u32(dev, "microchip,dv-gain", &prop)) {
+ if (!pac1921_gain_param_valid(prop, PAC1921_GAIN_DV_GAIN_MAX))
+ return dev_err_probe(dev, -EINVAL,
+ "Invalid dv_gain: %u\n", prop);
+
+ priv->dv_gain = (u8)ilog2(prop);
+ }
+ if (!device_property_read_u32(dev, "microchip,di-gain", &prop)) {
+ if (!pac1921_gain_param_valid(prop, PAC1921_GAIN_DI_GAIN_MAX))
+ return dev_err_probe(dev, -EINVAL,
+ "Invalid di_gain: %u\n", prop);
+
+ priv->di_gain = (u8)ilog2(prop);
+ }
+ return 0;
+}
+
+static int pac1921_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct pac1921_priv *priv;
+
+ struct iio_dev *indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ priv = iio_priv(indio_dev);
+ priv->client = client;
+ i2c_set_clientdata(client, indio_dev);
+
+ priv->regmap = devm_regmap_init_i2c(client, &pac1921_regmap_config);
+ if (IS_ERR(priv->regmap))
+ dev_err_probe(dev, (int)PTR_ERR(priv->regmap),
+ "Cannot initialize register map\n");
+
+ mutex_init(&priv->lock);
+
+ priv->dv_gain = PAC1921_DEFAULT_DV_GAIN;
+ priv->di_gain = PAC1921_DEFAULT_DI_GAIN;
+ priv->high_res = PAC1921_DEFAULT_HIGH_RES;
+ priv->n_samples = PAC1921_DEFAULT_NUM_SAMPLES;
+ priv->filters_en = PAC1921_DEFAULT_FILTERS_ENABLED;
+
+ int ret = pac1921_parse_properties(priv);
+ if (ret)
+ return ret;
+
+ ret = pac1921_init(priv);
+ if (ret)
+ return ret;
+
+ priv->iio_info = pac1921_iio;
+
+ const struct i2c_device_id *id = i2c_client_get_device_id(client);
+
+ indio_dev->name = id->name;
+ indio_dev->info = &priv->iio_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->channels = pac1921_channels;
+ indio_dev->num_channels = ARRAY_SIZE(pac1921_channels);
+
+ ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
+ &iio_pollfunc_store_time,
+ &pac1921_trigger_handler, NULL);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Cannot setup IIO triggered buffer\n");
+
+ ret = devm_iio_device_register(dev, indio_dev);
+ if (ret)
+ return dev_err_probe(dev, ret, "Cannot register IIO device\n");
+
+ return 0;
+}
+
+static const struct i2c_device_id pac1921_id[] = {
+ { .name = "pac1921", 0 },
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, pac1921_id);
+
+static const struct of_device_id pac1921_of_match[] = {
+ { .compatible = "microchip,pac1921" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, pac1921_of_match);
+
+static struct i2c_driver pac1921_driver = {
+ .driver = {
+ .name = "pac1921",
+ .pm = pm_sleep_ptr(&pac1921_pm_ops),
+ .of_match_table = pac1921_of_match,
+ },
+ .probe = pac1921_probe,
+ .id_table = pac1921_id,
+};
+
+module_i2c_driver(pac1921_driver);
+
+MODULE_AUTHOR("Matteo Martelli <matteomartelli3@gmail.com>");
+MODULE_DESCRIPTION("IIO driver for PAC1921 High-Side Power/Current Monitor");
+MODULE_LICENSE("GPL");
Add support for Microchip PAC1921 Power/Current monitor. Implemented features: * capture of bus voltage, sense voltage, current and power measurements in free-run integration mode * support for both raw and triggered buffer reading * support for overflow events * userspace controls for voltage and current gains, measurement resolution, integration samples and filters enabling/disabling * simple power management support Limitations: * operation mode fixed to free-run integration * measurement resolution and filters controls are applied to both VSENSE and VBUS measurements Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com> --- .../ABI/testing/sysfs-bus-iio-adc-pac1921 | 45 + MAINTAINERS | 7 + drivers/iio/adc/Kconfig | 10 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/pac1921.c | 1033 ++++++++++++++++++++ 5 files changed, 1096 insertions(+)