| Message ID | SEYPR01MB42215C6F248AF99499F6A050D7A22@SEYPR01MB4221.apcprd01.prod.exchangelabs.com (mailing list archive) |
|---|---|
| State | New |
| Delegated to: | Daniel Lezcano |
| Headers | show |
| Series | riscv: sophgo: add thermal sensor support for cv180x/sg200x SoCs | expand |
On 2024/7/16 17:42, Haylen Chu wrote: > Add support for cv180x SoCs integrated thermal sensors. > > Signed-off-by: Haylen Chu <heylenay@outlook.com> > --- > drivers/thermal/Kconfig | 6 + > drivers/thermal/Makefile | 1 + > drivers/thermal/cv180x_thermal.c | 241 +++++++++++++++++++++++++++++++ > 3 files changed, 248 insertions(+) > create mode 100644 drivers/thermal/cv180x_thermal.c cv18xx_thermal.c ? See my comments in patch 1. When you deicide it, update this for all patches. > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > index 204ed89a3ec9..f53c973a361d 100644 > --- a/drivers/thermal/Kconfig > +++ b/drivers/thermal/Kconfig > @@ -514,4 +514,10 @@ config LOONGSON2_THERMAL > is higher than the high temperature threshold or lower than the low > temperature threshold, the interrupt will occur. > > +config CV180X_THERMAL Same question above, CV18XX_THERMAL? > + tristate "Temperature sensor driver for Sophgo CV180X" > + help > + If you say yes here you get support for thermal sensor integrated in > + Sophgo CV180X SoCs. > + > endif > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > index 5cdf7d68687f..5b59bde8a579 100644 > --- a/drivers/thermal/Makefile > +++ b/drivers/thermal/Makefile > @@ -65,3 +65,4 @@ obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o > obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o > obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o > obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o > +obj-$(CONFIG_CV180X_THERMAL) += cv180x_thermal.o > diff --git a/drivers/thermal/cv180x_thermal.c b/drivers/thermal/cv180x_thermal.c > new file mode 100644 > index 000000000000..8b726c0ad848 > --- /dev/null > +++ b/drivers/thermal/cv180x_thermal.c > @@ -0,0 +1,241 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2021 Sophgo Inc. > + * Copyright (C) 2024 Haylen Chu <heylenay@outlook.com> > + */ > + > +#include <linux/bits.h> > +#include <linux/clk.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/thermal.h> > + > +#define TEMPSEN_VERSION 0x0 > +#define TEMPSEN_CTRL 0x4 > +#define TEMPSEN_CTRL_EN BIT(0) > +#define TEMPSEN_CTRL_SEL_MASK GENMASK(7, 4) > +#define TEMPSEN_CTRL_SEL_OFFSET 4 > +#define TEMPSEN_STATUS 0x8 > +#define TEMPSEN_SET 0xc > +#define TEMPSEN_SET_CHOPSEL_MASK GENMASK(5, 4) > +#define TEMPSEN_SET_CHOPSEL_OFFSET 4 > +#define TEMPSEN_SET_CHOPSEL_128T 0 > +#define TEMPSEN_SET_CHOPSEL_256T 1 > +#define TEMPSEN_SET_CHOPSEL_512T 2 > +#define TEMPSEN_SET_CHOPSEL_1024T 3 > +#define TEMPSEN_SET_ACCSEL_MASK GENMASK(7, 6) > +#define TEMPSEN_SET_ACCSEL_OFFSET 6 > +#define TEMPSEN_SET_ACCSEL_512T 0 > +#define TEMPSEN_SET_ACCSEL_1024T 1 > +#define TEMPSEN_SET_ACCSEL_2048T 2 > +#define TEMPSEN_SET_ACCSEL_4096T 3 > +#define TEMPSEN_SET_CYC_CLKDIV_MASK GENMASK(15, 8) > +#define TEMPSEN_SET_CYC_CLKDIV_OFFSET 8 > +#define TEMPSEN_INTR_EN 0x10 > +#define TEMPSEN_INTR_CLR 0x14 > +#define TEMPSEN_INTR_STA 0x18 > +#define TEMPSEN_INTR_RAW 0x1c > +#define TEMPSEN_RESULT(n) (0x20 + (n) * 4) > +#define TEMPSEN_RESULT_RESULT_MASK GENMASK(12, 0) > +#define TEMPSEN_RESULT_MAX_RESULT_MASK GENMASK(28, 16) > +#define TEMPSEN_RESULT_CLR_MAX_RESULT BIT(31) > +#define TEMPSEN_AUTO_PERIOD 0x64 > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK GENMASK(23, 0) > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET 0 > + > +struct cv180x_thermal_zone { > + struct device *dev; > + void __iomem *base; > + struct clk *clk_tempsen; > + u32 sample_cycle; > +}; > + > +static void cv180x_thermal_init(struct cv180x_thermal_zone *ctz) > +{ > + void __iomem *base = ctz->base; > + u32 regval; > + > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > + writel(TEMPSEN_RESULT_CLR_MAX_RESULT, base + TEMPSEN_RESULT(0)); > + > + regval = readl(base + TEMPSEN_SET); > + regval &= ~TEMPSEN_SET_CHOPSEL_MASK; > + regval &= ~TEMPSEN_SET_ACCSEL_MASK; > + regval &= ~TEMPSEN_SET_CYC_CLKDIV_MASK; > + regval |= TEMPSEN_SET_CHOPSEL_1024T << TEMPSEN_SET_CHOPSEL_OFFSET; > + regval |= TEMPSEN_SET_ACCSEL_2048T << TEMPSEN_SET_ACCSEL_OFFSET; > + regval |= 0x31 << TEMPSEN_SET_CYC_CLKDIV_OFFSET; > + writel(regval, base + TEMPSEN_SET); > + > + regval = readl(base + TEMPSEN_AUTO_PERIOD); > + regval &= ~TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK; > + regval |= ctz->sample_cycle << TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET; > + writel(regval, base + TEMPSEN_AUTO_PERIOD); > + > + regval = readl(base + TEMPSEN_CTRL); > + regval &= ~TEMPSEN_CTRL_SEL_MASK; > + regval |= 1 << TEMPSEN_CTRL_SEL_OFFSET; > + regval |= TEMPSEN_CTRL_EN; > + writel(regval, base + TEMPSEN_CTRL); > +} > + > +static void cv180x_thermal_deinit(struct cv180x_thermal_zone *ct) > +{ > + void __iomem *base = ct->base; > + u32 regval; > + > + regval = readl(base + TEMPSEN_CTRL); > + regval &= ~(TEMPSEN_CTRL_SEL_MASK | TEMPSEN_CTRL_EN); > + writel(regval, base + TEMPSEN_CTRL); > + > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > +} > + > +/* > + * Raw register value to temperature (mC) formula: > + * > + * read_val * 1000 * 716 > + * Temperature = ----------------------- - 273000 > + * divider > + * > + * where divider should be ticks number of accumulation period, > + * e.g. 2048 for TEMPSEN_CTRL_ACCSEL_2048T > + */ > +static int cv180x_calc_temp(struct cv180x_thermal_zone *ctz, u32 result) > +{ > + return (result * 1000) * 716 / 2048 - 273000; > +} > + > +static int cv180x_get_temp(struct thermal_zone_device *tdev, int *temperature) > +{ > + struct cv180x_thermal_zone *ctz = thermal_zone_device_priv(tdev); > + void __iomem *base = ctz->base; > + u32 result; > + > + result = readl(base + TEMPSEN_RESULT(0)) & TEMPSEN_RESULT_RESULT_MASK; > + *temperature = cv180x_calc_temp(ctz, result); > + > + return 0; > +} > + > +static const struct thermal_zone_device_ops cv180x_thermal_ops = { > + .get_temp = cv180x_get_temp, > +}; > + > +static const struct of_device_id cv180x_thermal_of_match[] = { > + { .compatible = "sophgo,cv1800-thermal" }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, cv180x_thermal_of_match); > + > +static int > +cv180x_parse_dt(struct cv180x_thermal_zone *ctz) > +{ > + struct device_node *np = ctz->dev->of_node; > + u32 tmp; > + > + if (of_property_read_u32(np, "sample-rate-hz", &tmp)) { > + ctz->sample_cycle = 1000000; > + } else { > + /* sample cycle should be at least 524us */ > + if (tmp > 1000000 / 524) { > + dev_err(ctz->dev, "invalid sample rate %d\n", tmp); > + return -EINVAL; > + } > + > + ctz->sample_cycle = 1000000 / tmp; > + } > + > + return 0; > +} > + > +static int cv180x_thermal_probe(struct platform_device *pdev) > +{ > + struct cv180x_thermal_zone *ctz; > + struct thermal_zone_device *tz; > + struct resource *res; > + int ret; > + > + ctz = devm_kzalloc(&pdev->dev, sizeof(*ctz), GFP_KERNEL); > + if (!ctz) > + return -ENOMEM; > + > + ctz->dev = &pdev->dev; > + > + ret = cv180x_parse_dt(ctz); > + if (ret) > + return dev_err_probe(&pdev->dev, ret, "failed to parse dt\n"); > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + ctz->base = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(ctz->base)) > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->base), > + "failed to map tempsen registers\n"); > + > + ctz->clk_tempsen = devm_clk_get_enabled(&pdev->dev, NULL); > + if (IS_ERR(ctz->clk_tempsen)) > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->clk_tempsen), > + "failed to get clk_tempsen\n"); > + > + cv180x_thermal_init(ctz); > + > + tz = devm_thermal_of_zone_register(&pdev->dev, 0, ctz, > + &cv180x_thermal_ops); > + if (IS_ERR(tz)) > + return dev_err_probe(&pdev->dev, PTR_ERR(tz), > + "failed to register thermal zone\n"); > + > + platform_set_drvdata(pdev, ctz); > + > + return 0; > +} > + > +static int cv180x_thermal_remove(struct platform_device *pdev) > +{ > + struct cv180x_thermal_zone *ctz = platform_get_drvdata(pdev); > + > + cv180x_thermal_deinit(ctz); > + > + return 0; > +} > + > +static int __maybe_unused cv180x_thermal_suspend(struct device *dev) > +{ > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > + > + cv180x_thermal_deinit(ctz); > + clk_disable_unprepare(ctz->clk_tempsen); > + > + return 0; > +} > + > +static int __maybe_unused cv180x_thermal_resume(struct device *dev) > +{ > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > + > + clk_prepare_enable(ctz->clk_tempsen); > + cv180x_thermal_init(ctz); > + > + return 0; > +} > + > +static SIMPLE_DEV_PM_OPS(cv180x_thermal_pm_ops, > + cv180x_thermal_suspend, cv180x_thermal_resume); > + > +static struct platform_driver cv180x_thermal_driver = { > + .probe = cv180x_thermal_probe, > + .remove = cv180x_thermal_remove, > + .driver = { > + .name = "cv180x-thermal", > + .pm = &cv180x_thermal_pm_ops, > + .of_match_table = cv180x_thermal_of_match, > + }, > +}; > + > +module_platform_driver(cv180x_thermal_driver); > + > +MODULE_DESCRIPTION("Sophgo CV180x thermal driver"); > +MODULE_AUTHOR("Haylen Chu <heylenay@outlook.com>"); > +MODULE_LICENSE("GPL");
On Tue, Jul 16, 2024 at 08:48:13PM +0800, Chen Wang wrote: > > On 2024/7/16 17:42, Haylen Chu wrote: > > Add support for cv180x SoCs integrated thermal sensors. > > > > Signed-off-by: Haylen Chu <heylenay@outlook.com> > > --- > > drivers/thermal/Kconfig | 6 + > > drivers/thermal/Makefile | 1 + > > drivers/thermal/cv180x_thermal.c | 241 +++++++++++++++++++++++++++++++ > > 3 files changed, 248 insertions(+) > > create mode 100644 drivers/thermal/cv180x_thermal.c > cv18xx_thermal.c ? See my comments in patch 1. When you deicide it, update > this for all patches. I would use unified "cv1800" in next revision. Best regards, Haylen > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > > index 204ed89a3ec9..f53c973a361d 100644 > > --- a/drivers/thermal/Kconfig > > +++ b/drivers/thermal/Kconfig > > @@ -514,4 +514,10 @@ config LOONGSON2_THERMAL > > is higher than the high temperature threshold or lower than the low > > temperature threshold, the interrupt will occur. > > +config CV180X_THERMAL > Same question above, CV18XX_THERMAL? > > + tristate "Temperature sensor driver for Sophgo CV180X" > > + help > > + If you say yes here you get support for thermal sensor integrated in > > + Sophgo CV180X SoCs. > > + > > endif > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > > index 5cdf7d68687f..5b59bde8a579 100644 > > --- a/drivers/thermal/Makefile > > +++ b/drivers/thermal/Makefile > > @@ -65,3 +65,4 @@ obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o > > obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o > > obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o > > obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o > > +obj-$(CONFIG_CV180X_THERMAL) += cv180x_thermal.o > > diff --git a/drivers/thermal/cv180x_thermal.c b/drivers/thermal/cv180x_thermal.c > > new file mode 100644 > > index 000000000000..8b726c0ad848 > > --- /dev/null > > +++ b/drivers/thermal/cv180x_thermal.c > > @@ -0,0 +1,241 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (C) 2021 Sophgo Inc. > > + * Copyright (C) 2024 Haylen Chu <heylenay@outlook.com> > > + */ > > + > > +#include <linux/bits.h> > > +#include <linux/clk.h> > > +#include <linux/io.h> > > +#include <linux/module.h> > > +#include <linux/of.h> > > +#include <linux/platform_device.h> > > +#include <linux/thermal.h> > > + > > +#define TEMPSEN_VERSION 0x0 > > +#define TEMPSEN_CTRL 0x4 > > +#define TEMPSEN_CTRL_EN BIT(0) > > +#define TEMPSEN_CTRL_SEL_MASK GENMASK(7, 4) > > +#define TEMPSEN_CTRL_SEL_OFFSET 4 > > +#define TEMPSEN_STATUS 0x8 > > +#define TEMPSEN_SET 0xc > > +#define TEMPSEN_SET_CHOPSEL_MASK GENMASK(5, 4) > > +#define TEMPSEN_SET_CHOPSEL_OFFSET 4 > > +#define TEMPSEN_SET_CHOPSEL_128T 0 > > +#define TEMPSEN_SET_CHOPSEL_256T 1 > > +#define TEMPSEN_SET_CHOPSEL_512T 2 > > +#define TEMPSEN_SET_CHOPSEL_1024T 3 > > +#define TEMPSEN_SET_ACCSEL_MASK GENMASK(7, 6) > > +#define TEMPSEN_SET_ACCSEL_OFFSET 6 > > +#define TEMPSEN_SET_ACCSEL_512T 0 > > +#define TEMPSEN_SET_ACCSEL_1024T 1 > > +#define TEMPSEN_SET_ACCSEL_2048T 2 > > +#define TEMPSEN_SET_ACCSEL_4096T 3 > > +#define TEMPSEN_SET_CYC_CLKDIV_MASK GENMASK(15, 8) > > +#define TEMPSEN_SET_CYC_CLKDIV_OFFSET 8 > > +#define TEMPSEN_INTR_EN 0x10 > > +#define TEMPSEN_INTR_CLR 0x14 > > +#define TEMPSEN_INTR_STA 0x18 > > +#define TEMPSEN_INTR_RAW 0x1c > > +#define TEMPSEN_RESULT(n) (0x20 + (n) * 4) > > +#define TEMPSEN_RESULT_RESULT_MASK GENMASK(12, 0) > > +#define TEMPSEN_RESULT_MAX_RESULT_MASK GENMASK(28, 16) > > +#define TEMPSEN_RESULT_CLR_MAX_RESULT BIT(31) > > +#define TEMPSEN_AUTO_PERIOD 0x64 > > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK GENMASK(23, 0) > > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET 0 > > + > > +struct cv180x_thermal_zone { > > + struct device *dev; > > + void __iomem *base; > > + struct clk *clk_tempsen; > > + u32 sample_cycle; > > +}; > > + > > +static void cv180x_thermal_init(struct cv180x_thermal_zone *ctz) > > +{ > > + void __iomem *base = ctz->base; > > + u32 regval; > > + > > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > > + writel(TEMPSEN_RESULT_CLR_MAX_RESULT, base + TEMPSEN_RESULT(0)); > > + > > + regval = readl(base + TEMPSEN_SET); > > + regval &= ~TEMPSEN_SET_CHOPSEL_MASK; > > + regval &= ~TEMPSEN_SET_ACCSEL_MASK; > > + regval &= ~TEMPSEN_SET_CYC_CLKDIV_MASK; > > + regval |= TEMPSEN_SET_CHOPSEL_1024T << TEMPSEN_SET_CHOPSEL_OFFSET; > > + regval |= TEMPSEN_SET_ACCSEL_2048T << TEMPSEN_SET_ACCSEL_OFFSET; > > + regval |= 0x31 << TEMPSEN_SET_CYC_CLKDIV_OFFSET; > > + writel(regval, base + TEMPSEN_SET); > > + > > + regval = readl(base + TEMPSEN_AUTO_PERIOD); > > + regval &= ~TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK; > > + regval |= ctz->sample_cycle << TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET; > > + writel(regval, base + TEMPSEN_AUTO_PERIOD); > > + > > + regval = readl(base + TEMPSEN_CTRL); > > + regval &= ~TEMPSEN_CTRL_SEL_MASK; > > + regval |= 1 << TEMPSEN_CTRL_SEL_OFFSET; > > + regval |= TEMPSEN_CTRL_EN; > > + writel(regval, base + TEMPSEN_CTRL); > > +} > > + > > +static void cv180x_thermal_deinit(struct cv180x_thermal_zone *ct) > > +{ > > + void __iomem *base = ct->base; > > + u32 regval; > > + > > + regval = readl(base + TEMPSEN_CTRL); > > + regval &= ~(TEMPSEN_CTRL_SEL_MASK | TEMPSEN_CTRL_EN); > > + writel(regval, base + TEMPSEN_CTRL); > > + > > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > > +} > > + > > +/* > > + * Raw register value to temperature (mC) formula: > > + * > > + * read_val * 1000 * 716 > > + * Temperature = ----------------------- - 273000 > > + * divider > > + * > > + * where divider should be ticks number of accumulation period, > > + * e.g. 2048 for TEMPSEN_CTRL_ACCSEL_2048T > > + */ > > +static int cv180x_calc_temp(struct cv180x_thermal_zone *ctz, u32 result) > > +{ > > + return (result * 1000) * 716 / 2048 - 273000; > > +} > > + > > +static int cv180x_get_temp(struct thermal_zone_device *tdev, int *temperature) > > +{ > > + struct cv180x_thermal_zone *ctz = thermal_zone_device_priv(tdev); > > + void __iomem *base = ctz->base; > > + u32 result; > > + > > + result = readl(base + TEMPSEN_RESULT(0)) & TEMPSEN_RESULT_RESULT_MASK; > > + *temperature = cv180x_calc_temp(ctz, result); > > + > > + return 0; > > +} > > + > > +static const struct thermal_zone_device_ops cv180x_thermal_ops = { > > + .get_temp = cv180x_get_temp, > > +}; > > + > > +static const struct of_device_id cv180x_thermal_of_match[] = { > > + { .compatible = "sophgo,cv1800-thermal" }, > > + {}, > > +}; > > +MODULE_DEVICE_TABLE(of, cv180x_thermal_of_match); > > + > > +static int > > +cv180x_parse_dt(struct cv180x_thermal_zone *ctz) > > +{ > > + struct device_node *np = ctz->dev->of_node; > > + u32 tmp; > > + > > + if (of_property_read_u32(np, "sample-rate-hz", &tmp)) { > > + ctz->sample_cycle = 1000000; > > + } else { > > + /* sample cycle should be at least 524us */ > > + if (tmp > 1000000 / 524) { > > + dev_err(ctz->dev, "invalid sample rate %d\n", tmp); > > + return -EINVAL; > > + } > > + > > + ctz->sample_cycle = 1000000 / tmp; > > + } > > + > > + return 0; > > +} > > + > > +static int cv180x_thermal_probe(struct platform_device *pdev) > > +{ > > + struct cv180x_thermal_zone *ctz; > > + struct thermal_zone_device *tz; > > + struct resource *res; > > + int ret; > > + > > + ctz = devm_kzalloc(&pdev->dev, sizeof(*ctz), GFP_KERNEL); > > + if (!ctz) > > + return -ENOMEM; > > + > > + ctz->dev = &pdev->dev; > > + > > + ret = cv180x_parse_dt(ctz); > > + if (ret) > > + return dev_err_probe(&pdev->dev, ret, "failed to parse dt\n"); > > + > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > + ctz->base = devm_ioremap_resource(&pdev->dev, res); > > + if (IS_ERR(ctz->base)) > > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->base), > > + "failed to map tempsen registers\n"); > > + > > + ctz->clk_tempsen = devm_clk_get_enabled(&pdev->dev, NULL); > > + if (IS_ERR(ctz->clk_tempsen)) > > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->clk_tempsen), > > + "failed to get clk_tempsen\n"); > > + > > + cv180x_thermal_init(ctz); > > + > > + tz = devm_thermal_of_zone_register(&pdev->dev, 0, ctz, > > + &cv180x_thermal_ops); > > + if (IS_ERR(tz)) > > + return dev_err_probe(&pdev->dev, PTR_ERR(tz), > > + "failed to register thermal zone\n"); > > + > > + platform_set_drvdata(pdev, ctz); > > + > > + return 0; > > +} > > + > > +static int cv180x_thermal_remove(struct platform_device *pdev) > > +{ > > + struct cv180x_thermal_zone *ctz = platform_get_drvdata(pdev); > > + > > + cv180x_thermal_deinit(ctz); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused cv180x_thermal_suspend(struct device *dev) > > +{ > > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > > + > > + cv180x_thermal_deinit(ctz); > > + clk_disable_unprepare(ctz->clk_tempsen); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused cv180x_thermal_resume(struct device *dev) > > +{ > > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > > + > > + clk_prepare_enable(ctz->clk_tempsen); > > + cv180x_thermal_init(ctz); > > + > > + return 0; > > +} > > + > > +static SIMPLE_DEV_PM_OPS(cv180x_thermal_pm_ops, > > + cv180x_thermal_suspend, cv180x_thermal_resume); > > + > > +static struct platform_driver cv180x_thermal_driver = { > > + .probe = cv180x_thermal_probe, > > + .remove = cv180x_thermal_remove, > > + .driver = { > > + .name = "cv180x-thermal", > > + .pm = &cv180x_thermal_pm_ops, > > + .of_match_table = cv180x_thermal_of_match, > > + }, > > +}; > > + > > +module_platform_driver(cv180x_thermal_driver); > > + > > +MODULE_DESCRIPTION("Sophgo CV180x thermal driver"); > > +MODULE_AUTHOR("Haylen Chu <heylenay@outlook.com>"); > > +MODULE_LICENSE("GPL");
On Tue, Jul 16, 2024 at 09:42:35AM GMT, Haylen Chu wrote: > Add support for cv180x SoCs integrated thermal sensors. > > Signed-off-by: Haylen Chu <heylenay@outlook.com> > --- > drivers/thermal/Kconfig | 6 + > drivers/thermal/Makefile | 1 + > drivers/thermal/cv180x_thermal.c | 241 +++++++++++++++++++++++++++++++ > 3 files changed, 248 insertions(+) > create mode 100644 drivers/thermal/cv180x_thermal.c > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > index 204ed89a3ec9..f53c973a361d 100644 > --- a/drivers/thermal/Kconfig > +++ b/drivers/thermal/Kconfig > @@ -514,4 +514,10 @@ config LOONGSON2_THERMAL > is higher than the high temperature threshold or lower than the low > temperature threshold, the interrupt will occur. > > +config CV180X_THERMAL > + tristate "Temperature sensor driver for Sophgo CV180X" > + help > + If you say yes here you get support for thermal sensor integrated in > + Sophgo CV180X SoCs. > + > endif > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > index 5cdf7d68687f..5b59bde8a579 100644 > --- a/drivers/thermal/Makefile > +++ b/drivers/thermal/Makefile > @@ -65,3 +65,4 @@ obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o > obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o > obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o > obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o > +obj-$(CONFIG_CV180X_THERMAL) += cv180x_thermal.o > diff --git a/drivers/thermal/cv180x_thermal.c b/drivers/thermal/cv180x_thermal.c > new file mode 100644 > index 000000000000..8b726c0ad848 > --- /dev/null > +++ b/drivers/thermal/cv180x_thermal.c > @@ -0,0 +1,241 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2021 Sophgo Inc. > + * Copyright (C) 2024 Haylen Chu <heylenay@outlook.com> > + */ > + > +#include <linux/bits.h> > +#include <linux/clk.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/thermal.h> > + > +#define TEMPSEN_VERSION 0x0 > +#define TEMPSEN_CTRL 0x4 > +#define TEMPSEN_CTRL_EN BIT(0) > +#define TEMPSEN_CTRL_SEL_MASK GENMASK(7, 4) > +#define TEMPSEN_CTRL_SEL_OFFSET 4 > +#define TEMPSEN_STATUS 0x8 > +#define TEMPSEN_SET 0xc > +#define TEMPSEN_SET_CHOPSEL_MASK GENMASK(5, 4) > +#define TEMPSEN_SET_CHOPSEL_OFFSET 4 > +#define TEMPSEN_SET_CHOPSEL_128T 0 > +#define TEMPSEN_SET_CHOPSEL_256T 1 > +#define TEMPSEN_SET_CHOPSEL_512T 2 > +#define TEMPSEN_SET_CHOPSEL_1024T 3 > +#define TEMPSEN_SET_ACCSEL_MASK GENMASK(7, 6) > +#define TEMPSEN_SET_ACCSEL_OFFSET 6 > +#define TEMPSEN_SET_ACCSEL_512T 0 > +#define TEMPSEN_SET_ACCSEL_1024T 1 > +#define TEMPSEN_SET_ACCSEL_2048T 2 > +#define TEMPSEN_SET_ACCSEL_4096T 3 > +#define TEMPSEN_SET_CYC_CLKDIV_MASK GENMASK(15, 8) > +#define TEMPSEN_SET_CYC_CLKDIV_OFFSET 8 > +#define TEMPSEN_INTR_EN 0x10 > +#define TEMPSEN_INTR_CLR 0x14 > +#define TEMPSEN_INTR_STA 0x18 > +#define TEMPSEN_INTR_RAW 0x1c > +#define TEMPSEN_RESULT(n) (0x20 + (n) * 4) > +#define TEMPSEN_RESULT_RESULT_MASK GENMASK(12, 0) > +#define TEMPSEN_RESULT_MAX_RESULT_MASK GENMASK(28, 16) > +#define TEMPSEN_RESULT_CLR_MAX_RESULT BIT(31) > +#define TEMPSEN_AUTO_PERIOD 0x64 > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK GENMASK(23, 0) > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET 0 > + > +struct cv180x_thermal_zone { > + struct device *dev; > + void __iomem *base; > + struct clk *clk_tempsen; > + u32 sample_cycle; > +}; > + > +static void cv180x_thermal_init(struct cv180x_thermal_zone *ctz) > +{ > + void __iomem *base = ctz->base; > + u32 regval; > + > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > + writel(TEMPSEN_RESULT_CLR_MAX_RESULT, base + TEMPSEN_RESULT(0)); > + > + regval = readl(base + TEMPSEN_SET); > + regval &= ~TEMPSEN_SET_CHOPSEL_MASK; > + regval &= ~TEMPSEN_SET_ACCSEL_MASK; > + regval &= ~TEMPSEN_SET_CYC_CLKDIV_MASK; > + regval |= TEMPSEN_SET_CHOPSEL_1024T << TEMPSEN_SET_CHOPSEL_OFFSET; > + regval |= TEMPSEN_SET_ACCSEL_2048T << TEMPSEN_SET_ACCSEL_OFFSET; > + regval |= 0x31 << TEMPSEN_SET_CYC_CLKDIV_OFFSET; > + writel(regval, base + TEMPSEN_SET); > + > + regval = readl(base + TEMPSEN_AUTO_PERIOD); > + regval &= ~TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK; > + regval |= ctz->sample_cycle << TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET; > + writel(regval, base + TEMPSEN_AUTO_PERIOD); > + > + regval = readl(base + TEMPSEN_CTRL); > + regval &= ~TEMPSEN_CTRL_SEL_MASK; > + regval |= 1 << TEMPSEN_CTRL_SEL_OFFSET; > + regval |= TEMPSEN_CTRL_EN; > + writel(regval, base + TEMPSEN_CTRL); > +} > + > +static void cv180x_thermal_deinit(struct cv180x_thermal_zone *ct) > +{ > + void __iomem *base = ct->base; > + u32 regval; > + > + regval = readl(base + TEMPSEN_CTRL); > + regval &= ~(TEMPSEN_CTRL_SEL_MASK | TEMPSEN_CTRL_EN); > + writel(regval, base + TEMPSEN_CTRL); > + > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > +} > + > +/* > + * Raw register value to temperature (mC) formula: > + * > + * read_val * 1000 * 716 > + * Temperature = ----------------------- - 273000 > + * divider > + * > + * where divider should be ticks number of accumulation period, > + * e.g. 2048 for TEMPSEN_CTRL_ACCSEL_2048T > + */ > +static int cv180x_calc_temp(struct cv180x_thermal_zone *ctz, u32 result) > +{ > + return (result * 1000) * 716 / 2048 - 273000; > +} > + > +static int cv180x_get_temp(struct thermal_zone_device *tdev, int *temperature) > +{ > + struct cv180x_thermal_zone *ctz = thermal_zone_device_priv(tdev); > + void __iomem *base = ctz->base; > + u32 result; > + > + result = readl(base + TEMPSEN_RESULT(0)) & TEMPSEN_RESULT_RESULT_MASK; > + *temperature = cv180x_calc_temp(ctz, result); > + > + return 0; > +} > + > +static const struct thermal_zone_device_ops cv180x_thermal_ops = { > + .get_temp = cv180x_get_temp, > +}; > + > +static const struct of_device_id cv180x_thermal_of_match[] = { > + { .compatible = "sophgo,cv1800-thermal" }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, cv180x_thermal_of_match); > + > +static int > +cv180x_parse_dt(struct cv180x_thermal_zone *ctz) > +{ > + struct device_node *np = ctz->dev->of_node; > + u32 tmp; > + > + if (of_property_read_u32(np, "sample-rate-hz", &tmp)) { > + ctz->sample_cycle = 1000000; > + } else { > + /* sample cycle should be at least 524us */ > + if (tmp > 1000000 / 524) { > + dev_err(ctz->dev, "invalid sample rate %d\n", tmp); > + return -EINVAL; > + } > + > + ctz->sample_cycle = 1000000 / tmp; > + } > + > + return 0; > +} > + > +static int cv180x_thermal_probe(struct platform_device *pdev) > +{ > + struct cv180x_thermal_zone *ctz; > + struct thermal_zone_device *tz; > + struct resource *res; > + int ret; > + > + ctz = devm_kzalloc(&pdev->dev, sizeof(*ctz), GFP_KERNEL); > + if (!ctz) > + return -ENOMEM; > + > + ctz->dev = &pdev->dev; > + > + ret = cv180x_parse_dt(ctz); > + if (ret) > + return dev_err_probe(&pdev->dev, ret, "failed to parse dt\n"); > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + ctz->base = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(ctz->base)) > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->base), > + "failed to map tempsen registers\n"); > + > + ctz->clk_tempsen = devm_clk_get_enabled(&pdev->dev, NULL); > + if (IS_ERR(ctz->clk_tempsen)) > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->clk_tempsen), > + "failed to get clk_tempsen\n"); > + > + cv180x_thermal_init(ctz); > + > + tz = devm_thermal_of_zone_register(&pdev->dev, 0, ctz, > + &cv180x_thermal_ops); > + if (IS_ERR(tz)) > + return dev_err_probe(&pdev->dev, PTR_ERR(tz), > + "failed to register thermal zone\n"); > + > + platform_set_drvdata(pdev, ctz); > + > + return 0; > +} > + > +static int cv180x_thermal_remove(struct platform_device *pdev) > +{ > + struct cv180x_thermal_zone *ctz = platform_get_drvdata(pdev); > + > + cv180x_thermal_deinit(ctz); > + > + return 0; > +} > + > +static int __maybe_unused cv180x_thermal_suspend(struct device *dev) > +{ > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > + > + cv180x_thermal_deinit(ctz); > + clk_disable_unprepare(ctz->clk_tempsen); > + > + return 0; > +} > + > +static int __maybe_unused cv180x_thermal_resume(struct device *dev) > +{ > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > + > + clk_prepare_enable(ctz->clk_tempsen); > + cv180x_thermal_init(ctz); > + > + return 0; > +} > + > +static SIMPLE_DEV_PM_OPS(cv180x_thermal_pm_ops, > + cv180x_thermal_suspend, cv180x_thermal_resume); > + > +static struct platform_driver cv180x_thermal_driver = { > + .probe = cv180x_thermal_probe, > + .remove = cv180x_thermal_remove, > + .driver = { > + .name = "cv180x-thermal", > + .pm = &cv180x_thermal_pm_ops, > + .of_match_table = cv180x_thermal_of_match, > + }, > +}; > + > +module_platform_driver(cv180x_thermal_driver); > + > +MODULE_DESCRIPTION("Sophgo CV180x thermal driver"); > +MODULE_AUTHOR("Haylen Chu <heylenay@outlook.com>"); > +MODULE_LICENSE("GPL"); > -- > 2.45.2 > Where is interrupt handler? I see nothing about it. Regards, Inochi
On Wed, Jul 17, 2024 at 02:22:32PM +0800, Inochi Amaoto wrote: > On Tue, Jul 16, 2024 at 09:42:35AM GMT, Haylen Chu wrote: > > Add support for cv180x SoCs integrated thermal sensors. > > > > Signed-off-by: Haylen Chu <heylenay@outlook.com> > > --- > > drivers/thermal/Kconfig | 6 + > > drivers/thermal/Makefile | 1 + > > drivers/thermal/cv180x_thermal.c | 241 +++++++++++++++++++++++++++++++ > > 3 files changed, 248 insertions(+) > > create mode 100644 drivers/thermal/cv180x_thermal.c > > > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > > index 204ed89a3ec9..f53c973a361d 100644 > > --- a/drivers/thermal/Kconfig > > +++ b/drivers/thermal/Kconfig > > @@ -514,4 +514,10 @@ config LOONGSON2_THERMAL > > is higher than the high temperature threshold or lower than the low > > temperature threshold, the interrupt will occur. > > > > +config CV180X_THERMAL > > + tristate "Temperature sensor driver for Sophgo CV180X" > > + help > > + If you say yes here you get support for thermal sensor integrated in > > + Sophgo CV180X SoCs. > > + > > endif > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > > index 5cdf7d68687f..5b59bde8a579 100644 > > --- a/drivers/thermal/Makefile > > +++ b/drivers/thermal/Makefile > > @@ -65,3 +65,4 @@ obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o > > obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o > > obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o > > obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o > > +obj-$(CONFIG_CV180X_THERMAL) += cv180x_thermal.o > > diff --git a/drivers/thermal/cv180x_thermal.c b/drivers/thermal/cv180x_thermal.c > > new file mode 100644 > > index 000000000000..8b726c0ad848 > > --- /dev/null > > +++ b/drivers/thermal/cv180x_thermal.c > > @@ -0,0 +1,241 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (C) 2021 Sophgo Inc. > > + * Copyright (C) 2024 Haylen Chu <heylenay@outlook.com> > > + */ > > + > > +#include <linux/bits.h> > > +#include <linux/clk.h> > > +#include <linux/io.h> > > +#include <linux/module.h> > > +#include <linux/of.h> > > +#include <linux/platform_device.h> > > +#include <linux/thermal.h> > > + > > +#define TEMPSEN_VERSION 0x0 > > +#define TEMPSEN_CTRL 0x4 > > +#define TEMPSEN_CTRL_EN BIT(0) > > +#define TEMPSEN_CTRL_SEL_MASK GENMASK(7, 4) > > +#define TEMPSEN_CTRL_SEL_OFFSET 4 > > +#define TEMPSEN_STATUS 0x8 > > +#define TEMPSEN_SET 0xc > > +#define TEMPSEN_SET_CHOPSEL_MASK GENMASK(5, 4) > > +#define TEMPSEN_SET_CHOPSEL_OFFSET 4 > > +#define TEMPSEN_SET_CHOPSEL_128T 0 > > +#define TEMPSEN_SET_CHOPSEL_256T 1 > > +#define TEMPSEN_SET_CHOPSEL_512T 2 > > +#define TEMPSEN_SET_CHOPSEL_1024T 3 > > +#define TEMPSEN_SET_ACCSEL_MASK GENMASK(7, 6) > > +#define TEMPSEN_SET_ACCSEL_OFFSET 6 > > +#define TEMPSEN_SET_ACCSEL_512T 0 > > +#define TEMPSEN_SET_ACCSEL_1024T 1 > > +#define TEMPSEN_SET_ACCSEL_2048T 2 > > +#define TEMPSEN_SET_ACCSEL_4096T 3 > > +#define TEMPSEN_SET_CYC_CLKDIV_MASK GENMASK(15, 8) > > +#define TEMPSEN_SET_CYC_CLKDIV_OFFSET 8 > > +#define TEMPSEN_INTR_EN 0x10 > > +#define TEMPSEN_INTR_CLR 0x14 > > +#define TEMPSEN_INTR_STA 0x18 > > +#define TEMPSEN_INTR_RAW 0x1c > > +#define TEMPSEN_RESULT(n) (0x20 + (n) * 4) > > +#define TEMPSEN_RESULT_RESULT_MASK GENMASK(12, 0) > > +#define TEMPSEN_RESULT_MAX_RESULT_MASK GENMASK(28, 16) > > +#define TEMPSEN_RESULT_CLR_MAX_RESULT BIT(31) > > +#define TEMPSEN_AUTO_PERIOD 0x64 > > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK GENMASK(23, 0) > > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET 0 > > + > > +struct cv180x_thermal_zone { > > + struct device *dev; > > + void __iomem *base; > > + struct clk *clk_tempsen; > > + u32 sample_cycle; > > +}; > > + > > +static void cv180x_thermal_init(struct cv180x_thermal_zone *ctz) > > +{ > > + void __iomem *base = ctz->base; > > + u32 regval; > > + > > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > > + writel(TEMPSEN_RESULT_CLR_MAX_RESULT, base + TEMPSEN_RESULT(0)); > > + > > + regval = readl(base + TEMPSEN_SET); > > + regval &= ~TEMPSEN_SET_CHOPSEL_MASK; > > + regval &= ~TEMPSEN_SET_ACCSEL_MASK; > > + regval &= ~TEMPSEN_SET_CYC_CLKDIV_MASK; > > + regval |= TEMPSEN_SET_CHOPSEL_1024T << TEMPSEN_SET_CHOPSEL_OFFSET; > > + regval |= TEMPSEN_SET_ACCSEL_2048T << TEMPSEN_SET_ACCSEL_OFFSET; > > + regval |= 0x31 << TEMPSEN_SET_CYC_CLKDIV_OFFSET; > > + writel(regval, base + TEMPSEN_SET); > > + > > + regval = readl(base + TEMPSEN_AUTO_PERIOD); > > + regval &= ~TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK; > > + regval |= ctz->sample_cycle << TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET; > > + writel(regval, base + TEMPSEN_AUTO_PERIOD); > > + > > + regval = readl(base + TEMPSEN_CTRL); > > + regval &= ~TEMPSEN_CTRL_SEL_MASK; > > + regval |= 1 << TEMPSEN_CTRL_SEL_OFFSET; > > + regval |= TEMPSEN_CTRL_EN; > > + writel(regval, base + TEMPSEN_CTRL); > > +} > > + > > +static void cv180x_thermal_deinit(struct cv180x_thermal_zone *ct) > > +{ > > + void __iomem *base = ct->base; > > + u32 regval; > > + > > + regval = readl(base + TEMPSEN_CTRL); > > + regval &= ~(TEMPSEN_CTRL_SEL_MASK | TEMPSEN_CTRL_EN); > > + writel(regval, base + TEMPSEN_CTRL); > > + > > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > > +} > > + > > +/* > > + * Raw register value to temperature (mC) formula: > > + * > > + * read_val * 1000 * 716 > > + * Temperature = ----------------------- - 273000 > > + * divider > > + * > > + * where divider should be ticks number of accumulation period, > > + * e.g. 2048 for TEMPSEN_CTRL_ACCSEL_2048T > > + */ > > +static int cv180x_calc_temp(struct cv180x_thermal_zone *ctz, u32 result) > > +{ > > + return (result * 1000) * 716 / 2048 - 273000; > > +} > > + > > +static int cv180x_get_temp(struct thermal_zone_device *tdev, int *temperature) > > +{ > > + struct cv180x_thermal_zone *ctz = thermal_zone_device_priv(tdev); > > + void __iomem *base = ctz->base; > > + u32 result; > > + > > + result = readl(base + TEMPSEN_RESULT(0)) & TEMPSEN_RESULT_RESULT_MASK; > > + *temperature = cv180x_calc_temp(ctz, result); > > + > > + return 0; > > +} > > + > > +static const struct thermal_zone_device_ops cv180x_thermal_ops = { > > + .get_temp = cv180x_get_temp, > > +}; > > + > > +static const struct of_device_id cv180x_thermal_of_match[] = { > > + { .compatible = "sophgo,cv1800-thermal" }, > > + {}, > > +}; > > +MODULE_DEVICE_TABLE(of, cv180x_thermal_of_match); > > + > > +static int > > +cv180x_parse_dt(struct cv180x_thermal_zone *ctz) > > +{ > > + struct device_node *np = ctz->dev->of_node; > > + u32 tmp; > > + > > + if (of_property_read_u32(np, "sample-rate-hz", &tmp)) { > > + ctz->sample_cycle = 1000000; > > + } else { > > + /* sample cycle should be at least 524us */ > > + if (tmp > 1000000 / 524) { > > + dev_err(ctz->dev, "invalid sample rate %d\n", tmp); > > + return -EINVAL; > > + } > > + > > + ctz->sample_cycle = 1000000 / tmp; > > + } > > + > > + return 0; > > +} > > + > > +static int cv180x_thermal_probe(struct platform_device *pdev) > > +{ > > + struct cv180x_thermal_zone *ctz; > > + struct thermal_zone_device *tz; > > + struct resource *res; > > + int ret; > > + > > + ctz = devm_kzalloc(&pdev->dev, sizeof(*ctz), GFP_KERNEL); > > + if (!ctz) > > + return -ENOMEM; > > + > > + ctz->dev = &pdev->dev; > > + > > + ret = cv180x_parse_dt(ctz); > > + if (ret) > > + return dev_err_probe(&pdev->dev, ret, "failed to parse dt\n"); > > + > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > + ctz->base = devm_ioremap_resource(&pdev->dev, res); > > + if (IS_ERR(ctz->base)) > > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->base), > > + "failed to map tempsen registers\n"); > > + > > + ctz->clk_tempsen = devm_clk_get_enabled(&pdev->dev, NULL); > > + if (IS_ERR(ctz->clk_tempsen)) > > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->clk_tempsen), > > + "failed to get clk_tempsen\n"); > > + > > + cv180x_thermal_init(ctz); > > + > > + tz = devm_thermal_of_zone_register(&pdev->dev, 0, ctz, > > + &cv180x_thermal_ops); > > + if (IS_ERR(tz)) > > + return dev_err_probe(&pdev->dev, PTR_ERR(tz), > > + "failed to register thermal zone\n"); > > + > > + platform_set_drvdata(pdev, ctz); > > + > > + return 0; > > +} > > + > > +static int cv180x_thermal_remove(struct platform_device *pdev) > > +{ > > + struct cv180x_thermal_zone *ctz = platform_get_drvdata(pdev); > > + > > + cv180x_thermal_deinit(ctz); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused cv180x_thermal_suspend(struct device *dev) > > +{ > > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > > + > > + cv180x_thermal_deinit(ctz); > > + clk_disable_unprepare(ctz->clk_tempsen); > > + > > + return 0; > > +} > > + > > +static int __maybe_unused cv180x_thermal_resume(struct device *dev) > > +{ > > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > > + > > + clk_prepare_enable(ctz->clk_tempsen); > > + cv180x_thermal_init(ctz); > > + > > + return 0; > > +} > > + > > +static SIMPLE_DEV_PM_OPS(cv180x_thermal_pm_ops, > > + cv180x_thermal_suspend, cv180x_thermal_resume); > > + > > +static struct platform_driver cv180x_thermal_driver = { > > + .probe = cv180x_thermal_probe, > > + .remove = cv180x_thermal_remove, > > + .driver = { > > + .name = "cv180x-thermal", > > + .pm = &cv180x_thermal_pm_ops, > > + .of_match_table = cv180x_thermal_of_match, > > + }, > > +}; > > + > > +module_platform_driver(cv180x_thermal_driver); > > + > > +MODULE_DESCRIPTION("Sophgo CV180x thermal driver"); > > +MODULE_AUTHOR("Haylen Chu <heylenay@outlook.com>"); > > +MODULE_LICENSE("GPL"); > > -- > > 2.45.2 > > > > Where is interrupt handler? I see nothing about it. > > Regards, > Inochi Interrupts are not used. This driver implements only polling the temperature. Best regards, Haylen Chu
On Thu, Jul 18, 2024 at 06:49:05AM GMT, Haylen Chu wrote: > On Wed, Jul 17, 2024 at 02:22:32PM +0800, Inochi Amaoto wrote: > > On Tue, Jul 16, 2024 at 09:42:35AM GMT, Haylen Chu wrote: > > > Add support for cv180x SoCs integrated thermal sensors. > > > > > > Signed-off-by: Haylen Chu <heylenay@outlook.com> > > > --- > > > drivers/thermal/Kconfig | 6 + > > > drivers/thermal/Makefile | 1 + > > > drivers/thermal/cv180x_thermal.c | 241 +++++++++++++++++++++++++++++++ > > > 3 files changed, 248 insertions(+) > > > create mode 100644 drivers/thermal/cv180x_thermal.c > > > > > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > > > index 204ed89a3ec9..f53c973a361d 100644 > > > --- a/drivers/thermal/Kconfig > > > +++ b/drivers/thermal/Kconfig > > > @@ -514,4 +514,10 @@ config LOONGSON2_THERMAL > > > is higher than the high temperature threshold or lower than the low > > > temperature threshold, the interrupt will occur. > > > > > > +config CV180X_THERMAL > > > + tristate "Temperature sensor driver for Sophgo CV180X" > > > + help > > > + If you say yes here you get support for thermal sensor integrated in > > > + Sophgo CV180X SoCs. > > > + > > > endif > > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > > > index 5cdf7d68687f..5b59bde8a579 100644 > > > --- a/drivers/thermal/Makefile > > > +++ b/drivers/thermal/Makefile > > > @@ -65,3 +65,4 @@ obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o > > > obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o > > > obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o > > > obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o > > > +obj-$(CONFIG_CV180X_THERMAL) += cv180x_thermal.o > > > diff --git a/drivers/thermal/cv180x_thermal.c b/drivers/thermal/cv180x_thermal.c > > > new file mode 100644 > > > index 000000000000..8b726c0ad848 > > > --- /dev/null > > > +++ b/drivers/thermal/cv180x_thermal.c > > > @@ -0,0 +1,241 @@ > > > +// SPDX-License-Identifier: GPL-2.0 > > > +/* > > > + * Copyright (C) 2021 Sophgo Inc. > > > + * Copyright (C) 2024 Haylen Chu <heylenay@outlook.com> > > > + */ > > > + > > > +#include <linux/bits.h> > > > +#include <linux/clk.h> > > > +#include <linux/io.h> > > > +#include <linux/module.h> > > > +#include <linux/of.h> > > > +#include <linux/platform_device.h> > > > +#include <linux/thermal.h> > > > + > > > +#define TEMPSEN_VERSION 0x0 > > > +#define TEMPSEN_CTRL 0x4 > > > +#define TEMPSEN_CTRL_EN BIT(0) > > > +#define TEMPSEN_CTRL_SEL_MASK GENMASK(7, 4) > > > +#define TEMPSEN_CTRL_SEL_OFFSET 4 > > > +#define TEMPSEN_STATUS 0x8 > > > +#define TEMPSEN_SET 0xc > > > +#define TEMPSEN_SET_CHOPSEL_MASK GENMASK(5, 4) > > > +#define TEMPSEN_SET_CHOPSEL_OFFSET 4 > > > +#define TEMPSEN_SET_CHOPSEL_128T 0 > > > +#define TEMPSEN_SET_CHOPSEL_256T 1 > > > +#define TEMPSEN_SET_CHOPSEL_512T 2 > > > +#define TEMPSEN_SET_CHOPSEL_1024T 3 > > > +#define TEMPSEN_SET_ACCSEL_MASK GENMASK(7, 6) > > > +#define TEMPSEN_SET_ACCSEL_OFFSET 6 > > > +#define TEMPSEN_SET_ACCSEL_512T 0 > > > +#define TEMPSEN_SET_ACCSEL_1024T 1 > > > +#define TEMPSEN_SET_ACCSEL_2048T 2 > > > +#define TEMPSEN_SET_ACCSEL_4096T 3 > > > +#define TEMPSEN_SET_CYC_CLKDIV_MASK GENMASK(15, 8) > > > +#define TEMPSEN_SET_CYC_CLKDIV_OFFSET 8 > > > +#define TEMPSEN_INTR_EN 0x10 > > > +#define TEMPSEN_INTR_CLR 0x14 > > > +#define TEMPSEN_INTR_STA 0x18 > > > +#define TEMPSEN_INTR_RAW 0x1c > > > +#define TEMPSEN_RESULT(n) (0x20 + (n) * 4) > > > +#define TEMPSEN_RESULT_RESULT_MASK GENMASK(12, 0) > > > +#define TEMPSEN_RESULT_MAX_RESULT_MASK GENMASK(28, 16) > > > +#define TEMPSEN_RESULT_CLR_MAX_RESULT BIT(31) > > > +#define TEMPSEN_AUTO_PERIOD 0x64 > > > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK GENMASK(23, 0) > > > +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET 0 > > > + > > > +struct cv180x_thermal_zone { > > > + struct device *dev; > > > + void __iomem *base; > > > + struct clk *clk_tempsen; > > > + u32 sample_cycle; > > > +}; > > > + > > > +static void cv180x_thermal_init(struct cv180x_thermal_zone *ctz) > > > +{ > > > + void __iomem *base = ctz->base; > > > + u32 regval; > > > + > > > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > > > + writel(TEMPSEN_RESULT_CLR_MAX_RESULT, base + TEMPSEN_RESULT(0)); > > > + > > > + regval = readl(base + TEMPSEN_SET); > > > + regval &= ~TEMPSEN_SET_CHOPSEL_MASK; > > > + regval &= ~TEMPSEN_SET_ACCSEL_MASK; > > > + regval &= ~TEMPSEN_SET_CYC_CLKDIV_MASK; > > > + regval |= TEMPSEN_SET_CHOPSEL_1024T << TEMPSEN_SET_CHOPSEL_OFFSET; > > > + regval |= TEMPSEN_SET_ACCSEL_2048T << TEMPSEN_SET_ACCSEL_OFFSET; > > > + regval |= 0x31 << TEMPSEN_SET_CYC_CLKDIV_OFFSET; > > > + writel(regval, base + TEMPSEN_SET); > > > + > > > + regval = readl(base + TEMPSEN_AUTO_PERIOD); > > > + regval &= ~TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK; > > > + regval |= ctz->sample_cycle << TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET; > > > + writel(regval, base + TEMPSEN_AUTO_PERIOD); > > > + > > > + regval = readl(base + TEMPSEN_CTRL); > > > + regval &= ~TEMPSEN_CTRL_SEL_MASK; > > > + regval |= 1 << TEMPSEN_CTRL_SEL_OFFSET; > > > + regval |= TEMPSEN_CTRL_EN; > > > + writel(regval, base + TEMPSEN_CTRL); > > > +} > > > + > > > +static void cv180x_thermal_deinit(struct cv180x_thermal_zone *ct) > > > +{ > > > + void __iomem *base = ct->base; > > > + u32 regval; > > > + > > > + regval = readl(base + TEMPSEN_CTRL); > > > + regval &= ~(TEMPSEN_CTRL_SEL_MASK | TEMPSEN_CTRL_EN); > > > + writel(regval, base + TEMPSEN_CTRL); > > > + > > > + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); > > > +} > > > + > > > +/* > > > + * Raw register value to temperature (mC) formula: > > > + * > > > + * read_val * 1000 * 716 > > > + * Temperature = ----------------------- - 273000 > > > + * divider > > > + * > > > + * where divider should be ticks number of accumulation period, > > > + * e.g. 2048 for TEMPSEN_CTRL_ACCSEL_2048T > > > + */ > > > +static int cv180x_calc_temp(struct cv180x_thermal_zone *ctz, u32 result) > > > +{ > > > + return (result * 1000) * 716 / 2048 - 273000; > > > +} > > > + > > > +static int cv180x_get_temp(struct thermal_zone_device *tdev, int *temperature) > > > +{ > > > + struct cv180x_thermal_zone *ctz = thermal_zone_device_priv(tdev); > > > + void __iomem *base = ctz->base; > > > + u32 result; > > > + > > > + result = readl(base + TEMPSEN_RESULT(0)) & TEMPSEN_RESULT_RESULT_MASK; > > > + *temperature = cv180x_calc_temp(ctz, result); > > > + > > > + return 0; > > > +} > > > + > > > +static const struct thermal_zone_device_ops cv180x_thermal_ops = { > > > + .get_temp = cv180x_get_temp, > > > +}; > > > + > > > +static const struct of_device_id cv180x_thermal_of_match[] = { > > > + { .compatible = "sophgo,cv1800-thermal" }, > > > + {}, > > > +}; > > > +MODULE_DEVICE_TABLE(of, cv180x_thermal_of_match); > > > + > > > +static int > > > +cv180x_parse_dt(struct cv180x_thermal_zone *ctz) > > > +{ > > > + struct device_node *np = ctz->dev->of_node; > > > + u32 tmp; > > > + > > > + if (of_property_read_u32(np, "sample-rate-hz", &tmp)) { > > > + ctz->sample_cycle = 1000000; > > > + } else { > > > + /* sample cycle should be at least 524us */ > > > + if (tmp > 1000000 / 524) { > > > + dev_err(ctz->dev, "invalid sample rate %d\n", tmp); > > > + return -EINVAL; > > > + } > > > + > > > + ctz->sample_cycle = 1000000 / tmp; > > > + } > > > + > > > + return 0; > > > +} > > > + > > > +static int cv180x_thermal_probe(struct platform_device *pdev) > > > +{ > > > + struct cv180x_thermal_zone *ctz; > > > + struct thermal_zone_device *tz; > > > + struct resource *res; > > > + int ret; > > > + > > > + ctz = devm_kzalloc(&pdev->dev, sizeof(*ctz), GFP_KERNEL); > > > + if (!ctz) > > > + return -ENOMEM; > > > + > > > + ctz->dev = &pdev->dev; > > > + > > > + ret = cv180x_parse_dt(ctz); > > > + if (ret) > > > + return dev_err_probe(&pdev->dev, ret, "failed to parse dt\n"); > > > + > > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > > + ctz->base = devm_ioremap_resource(&pdev->dev, res); > > > + if (IS_ERR(ctz->base)) > > > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->base), > > > + "failed to map tempsen registers\n"); > > > + > > > + ctz->clk_tempsen = devm_clk_get_enabled(&pdev->dev, NULL); > > > + if (IS_ERR(ctz->clk_tempsen)) > > > + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->clk_tempsen), > > > + "failed to get clk_tempsen\n"); > > > + > > > + cv180x_thermal_init(ctz); > > > + > > > + tz = devm_thermal_of_zone_register(&pdev->dev, 0, ctz, > > > + &cv180x_thermal_ops); > > > + if (IS_ERR(tz)) > > > + return dev_err_probe(&pdev->dev, PTR_ERR(tz), > > > + "failed to register thermal zone\n"); > > > + > > > + platform_set_drvdata(pdev, ctz); > > > + > > > + return 0; > > > +} > > > + > > > +static int cv180x_thermal_remove(struct platform_device *pdev) > > > +{ > > > + struct cv180x_thermal_zone *ctz = platform_get_drvdata(pdev); > > > + > > > + cv180x_thermal_deinit(ctz); > > > + > > > + return 0; > > > +} > > > + > > > +static int __maybe_unused cv180x_thermal_suspend(struct device *dev) > > > +{ > > > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > > > + > > > + cv180x_thermal_deinit(ctz); > > > + clk_disable_unprepare(ctz->clk_tempsen); > > > + > > > + return 0; > > > +} > > > + > > > +static int __maybe_unused cv180x_thermal_resume(struct device *dev) > > > +{ > > > + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); > > > + > > > + clk_prepare_enable(ctz->clk_tempsen); > > > + cv180x_thermal_init(ctz); > > > + > > > + return 0; > > > +} > > > + > > > +static SIMPLE_DEV_PM_OPS(cv180x_thermal_pm_ops, > > > + cv180x_thermal_suspend, cv180x_thermal_resume); > > > + > > > +static struct platform_driver cv180x_thermal_driver = { > > > + .probe = cv180x_thermal_probe, > > > + .remove = cv180x_thermal_remove, > > > + .driver = { > > > + .name = "cv180x-thermal", > > > + .pm = &cv180x_thermal_pm_ops, > > > + .of_match_table = cv180x_thermal_of_match, > > > + }, > > > +}; > > > + > > > +module_platform_driver(cv180x_thermal_driver); > > > + > > > +MODULE_DESCRIPTION("Sophgo CV180x thermal driver"); > > > +MODULE_AUTHOR("Haylen Chu <heylenay@outlook.com>"); > > > +MODULE_LICENSE("GPL"); > > > -- > > > 2.45.2 > > > > > > > Where is interrupt handler? I see nothing about it. > > > > Regards, > > Inochi > > Interrupts are not used. This driver implements only polling the > temperature. > > Best regards, > Haylen Chu "xxx is not used" is not the reason for you to not implement it. In addition, interrupt-driven is not just for reading sensors. I have seen something important like critical alert. Drop interrupt support may miss these alert. If you do not want to implement this, move your driver to staging as it is not complete. Regard, Inochi
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 204ed89a3ec9..f53c973a361d 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -514,4 +514,10 @@ config LOONGSON2_THERMAL is higher than the high temperature threshold or lower than the low temperature threshold, the interrupt will occur. +config CV180X_THERMAL + tristate "Temperature sensor driver for Sophgo CV180X" + help + If you say yes here you get support for thermal sensor integrated in + Sophgo CV180X SoCs. + endif diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index 5cdf7d68687f..5b59bde8a579 100644 --- a/drivers/thermal/Makefile +++ b/drivers/thermal/Makefile @@ -65,3 +65,4 @@ obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o +obj-$(CONFIG_CV180X_THERMAL) += cv180x_thermal.o diff --git a/drivers/thermal/cv180x_thermal.c b/drivers/thermal/cv180x_thermal.c new file mode 100644 index 000000000000..8b726c0ad848 --- /dev/null +++ b/drivers/thermal/cv180x_thermal.c @@ -0,0 +1,241 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Sophgo Inc. + * Copyright (C) 2024 Haylen Chu <heylenay@outlook.com> + */ + +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/thermal.h> + +#define TEMPSEN_VERSION 0x0 +#define TEMPSEN_CTRL 0x4 +#define TEMPSEN_CTRL_EN BIT(0) +#define TEMPSEN_CTRL_SEL_MASK GENMASK(7, 4) +#define TEMPSEN_CTRL_SEL_OFFSET 4 +#define TEMPSEN_STATUS 0x8 +#define TEMPSEN_SET 0xc +#define TEMPSEN_SET_CHOPSEL_MASK GENMASK(5, 4) +#define TEMPSEN_SET_CHOPSEL_OFFSET 4 +#define TEMPSEN_SET_CHOPSEL_128T 0 +#define TEMPSEN_SET_CHOPSEL_256T 1 +#define TEMPSEN_SET_CHOPSEL_512T 2 +#define TEMPSEN_SET_CHOPSEL_1024T 3 +#define TEMPSEN_SET_ACCSEL_MASK GENMASK(7, 6) +#define TEMPSEN_SET_ACCSEL_OFFSET 6 +#define TEMPSEN_SET_ACCSEL_512T 0 +#define TEMPSEN_SET_ACCSEL_1024T 1 +#define TEMPSEN_SET_ACCSEL_2048T 2 +#define TEMPSEN_SET_ACCSEL_4096T 3 +#define TEMPSEN_SET_CYC_CLKDIV_MASK GENMASK(15, 8) +#define TEMPSEN_SET_CYC_CLKDIV_OFFSET 8 +#define TEMPSEN_INTR_EN 0x10 +#define TEMPSEN_INTR_CLR 0x14 +#define TEMPSEN_INTR_STA 0x18 +#define TEMPSEN_INTR_RAW 0x1c +#define TEMPSEN_RESULT(n) (0x20 + (n) * 4) +#define TEMPSEN_RESULT_RESULT_MASK GENMASK(12, 0) +#define TEMPSEN_RESULT_MAX_RESULT_MASK GENMASK(28, 16) +#define TEMPSEN_RESULT_CLR_MAX_RESULT BIT(31) +#define TEMPSEN_AUTO_PERIOD 0x64 +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK GENMASK(23, 0) +#define TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET 0 + +struct cv180x_thermal_zone { + struct device *dev; + void __iomem *base; + struct clk *clk_tempsen; + u32 sample_cycle; +}; + +static void cv180x_thermal_init(struct cv180x_thermal_zone *ctz) +{ + void __iomem *base = ctz->base; + u32 regval; + + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); + writel(TEMPSEN_RESULT_CLR_MAX_RESULT, base + TEMPSEN_RESULT(0)); + + regval = readl(base + TEMPSEN_SET); + regval &= ~TEMPSEN_SET_CHOPSEL_MASK; + regval &= ~TEMPSEN_SET_ACCSEL_MASK; + regval &= ~TEMPSEN_SET_CYC_CLKDIV_MASK; + regval |= TEMPSEN_SET_CHOPSEL_1024T << TEMPSEN_SET_CHOPSEL_OFFSET; + regval |= TEMPSEN_SET_ACCSEL_2048T << TEMPSEN_SET_ACCSEL_OFFSET; + regval |= 0x31 << TEMPSEN_SET_CYC_CLKDIV_OFFSET; + writel(regval, base + TEMPSEN_SET); + + regval = readl(base + TEMPSEN_AUTO_PERIOD); + regval &= ~TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_MASK; + regval |= ctz->sample_cycle << TEMPSEN_AUTO_PERIOD_AUTO_CYCLE_OFFSET; + writel(regval, base + TEMPSEN_AUTO_PERIOD); + + regval = readl(base + TEMPSEN_CTRL); + regval &= ~TEMPSEN_CTRL_SEL_MASK; + regval |= 1 << TEMPSEN_CTRL_SEL_OFFSET; + regval |= TEMPSEN_CTRL_EN; + writel(regval, base + TEMPSEN_CTRL); +} + +static void cv180x_thermal_deinit(struct cv180x_thermal_zone *ct) +{ + void __iomem *base = ct->base; + u32 regval; + + regval = readl(base + TEMPSEN_CTRL); + regval &= ~(TEMPSEN_CTRL_SEL_MASK | TEMPSEN_CTRL_EN); + writel(regval, base + TEMPSEN_CTRL); + + writel(readl(base + TEMPSEN_INTR_RAW), base + TEMPSEN_INTR_CLR); +} + +/* + * Raw register value to temperature (mC) formula: + * + * read_val * 1000 * 716 + * Temperature = ----------------------- - 273000 + * divider + * + * where divider should be ticks number of accumulation period, + * e.g. 2048 for TEMPSEN_CTRL_ACCSEL_2048T + */ +static int cv180x_calc_temp(struct cv180x_thermal_zone *ctz, u32 result) +{ + return (result * 1000) * 716 / 2048 - 273000; +} + +static int cv180x_get_temp(struct thermal_zone_device *tdev, int *temperature) +{ + struct cv180x_thermal_zone *ctz = thermal_zone_device_priv(tdev); + void __iomem *base = ctz->base; + u32 result; + + result = readl(base + TEMPSEN_RESULT(0)) & TEMPSEN_RESULT_RESULT_MASK; + *temperature = cv180x_calc_temp(ctz, result); + + return 0; +} + +static const struct thermal_zone_device_ops cv180x_thermal_ops = { + .get_temp = cv180x_get_temp, +}; + +static const struct of_device_id cv180x_thermal_of_match[] = { + { .compatible = "sophgo,cv1800-thermal" }, + {}, +}; +MODULE_DEVICE_TABLE(of, cv180x_thermal_of_match); + +static int +cv180x_parse_dt(struct cv180x_thermal_zone *ctz) +{ + struct device_node *np = ctz->dev->of_node; + u32 tmp; + + if (of_property_read_u32(np, "sample-rate-hz", &tmp)) { + ctz->sample_cycle = 1000000; + } else { + /* sample cycle should be at least 524us */ + if (tmp > 1000000 / 524) { + dev_err(ctz->dev, "invalid sample rate %d\n", tmp); + return -EINVAL; + } + + ctz->sample_cycle = 1000000 / tmp; + } + + return 0; +} + +static int cv180x_thermal_probe(struct platform_device *pdev) +{ + struct cv180x_thermal_zone *ctz; + struct thermal_zone_device *tz; + struct resource *res; + int ret; + + ctz = devm_kzalloc(&pdev->dev, sizeof(*ctz), GFP_KERNEL); + if (!ctz) + return -ENOMEM; + + ctz->dev = &pdev->dev; + + ret = cv180x_parse_dt(ctz); + if (ret) + return dev_err_probe(&pdev->dev, ret, "failed to parse dt\n"); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + ctz->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(ctz->base)) + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->base), + "failed to map tempsen registers\n"); + + ctz->clk_tempsen = devm_clk_get_enabled(&pdev->dev, NULL); + if (IS_ERR(ctz->clk_tempsen)) + return dev_err_probe(&pdev->dev, PTR_ERR(ctz->clk_tempsen), + "failed to get clk_tempsen\n"); + + cv180x_thermal_init(ctz); + + tz = devm_thermal_of_zone_register(&pdev->dev, 0, ctz, + &cv180x_thermal_ops); + if (IS_ERR(tz)) + return dev_err_probe(&pdev->dev, PTR_ERR(tz), + "failed to register thermal zone\n"); + + platform_set_drvdata(pdev, ctz); + + return 0; +} + +static int cv180x_thermal_remove(struct platform_device *pdev) +{ + struct cv180x_thermal_zone *ctz = platform_get_drvdata(pdev); + + cv180x_thermal_deinit(ctz); + + return 0; +} + +static int __maybe_unused cv180x_thermal_suspend(struct device *dev) +{ + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); + + cv180x_thermal_deinit(ctz); + clk_disable_unprepare(ctz->clk_tempsen); + + return 0; +} + +static int __maybe_unused cv180x_thermal_resume(struct device *dev) +{ + struct cv180x_thermal_zone *ctz = dev_get_drvdata(dev); + + clk_prepare_enable(ctz->clk_tempsen); + cv180x_thermal_init(ctz); + + return 0; +} + +static SIMPLE_DEV_PM_OPS(cv180x_thermal_pm_ops, + cv180x_thermal_suspend, cv180x_thermal_resume); + +static struct platform_driver cv180x_thermal_driver = { + .probe = cv180x_thermal_probe, + .remove = cv180x_thermal_remove, + .driver = { + .name = "cv180x-thermal", + .pm = &cv180x_thermal_pm_ops, + .of_match_table = cv180x_thermal_of_match, + }, +}; + +module_platform_driver(cv180x_thermal_driver); + +MODULE_DESCRIPTION("Sophgo CV180x thermal driver"); +MODULE_AUTHOR("Haylen Chu <heylenay@outlook.com>"); +MODULE_LICENSE("GPL");
Add support for cv180x SoCs integrated thermal sensors. Signed-off-by: Haylen Chu <heylenay@outlook.com> --- drivers/thermal/Kconfig | 6 + drivers/thermal/Makefile | 1 + drivers/thermal/cv180x_thermal.c | 241 +++++++++++++++++++++++++++++++ 3 files changed, 248 insertions(+) create mode 100644 drivers/thermal/cv180x_thermal.c