[v12,00/28] Add i2c-mux and eeprom devices for Meta Yosemite 4

Message

Delphine CC Chiu Aug. 16, 2024, 9:23 a.m. UTC

Changelog:
  - v12
    - Fix GPIO linename typo and add missing GPIO pin initial state.
  - v11
    - Revise all GPIO line name with bottom line
  - v10
    - adjust mgm cpld ioexp bus
    - add GPIOO7 name
    - remove mctp driver
  - v9
    - add XDP710 support
    - add RTQ6056 support
    - add MP5990 support
  - v8
    - add fan led config
  - v7
    - Revise pca9506 i2c address
  - v6
    - Revise i2c duty-cycle for meeting 400khz spec
  - v5
    - Support medusa board adc sensors
    - support NIC eeprom
  - v4
    - Re-format gpio linename
    - Revise i2c device node names
    - Split patches by logic changes
  - v3
    - Correct patch for revising gpio name
  - v2
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name
  - v1
    - Add gpio and eeprom behind i2c-mux
    - Remove redundant idle-state setting for i2c-mux
    - Enable adc 15, wdt2,spi gpio for yosemite4 use
    - Revise quad mode to dual mode to avoid WP pin influnece the SPI
    - Revise power sensor adm1281 for yosemite4 schematic change
    - Add gpio pca9506 I/O expander for yosemite4 use
    - remove space for adm1272 compatible
    - enable interrupt setting for pca9555
    - add eeprom for yosemite4 medusa board/BSM use
    - remove temperature sensor for yosemite4 schematic change
    - add power sensor for power module reading
    - Revise adc128d818 adc mode for yosemite4 schematic change
    - Revise ina233 for yosemite4 schematic change
    - Remove idle state setting for yosemite4 NIC connection
    - Initialize bmc gpio state
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name

Delphine CC Chiu (28):
  ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
  ARM: dts: aspeed: yosemite4: Enable adc15
  ARM: dts: aspeed: yosemite4: Enable spi-gpio setting
  ARM: dts: aspeed: yosemite4: Enable watchdog2
  ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode
  ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic
    change
  ARM: dts: aspeed: yosemite4: Add gpio pca9506
  ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible
  ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555
  ARM: dts: aspeed: yosemite4: Add power sensor for power module reading
  ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use
  ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4
    NIC connection
  ARM: dts: aspeed: yosemite4: Initialize bmc gpio state
  ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config
  ARM: dts: aspeed: yosemite4: add mctp config for NIC
  ARM: dts: aspeed: yosemite4: support mux to cpld
  ARM: dts: aspeed: yosemite4: support medusa board adc sensors
  ARM: dts: aspeed: yosemite4: support NIC eeprom
  ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle
  ARM: dts: aspeed: yosemite4: add fan led config
  ARM: dts: aspeed: yosemite4: add XDP710
  ARM: dts: aspeed: yosemite4: add RTQ6056 support
  ARM: dts: aspeed: yosemite4: add MP5990 support
  ARM: dts: aspeed: yosemite4: Adjust ioexp bus and remove mctp driver
  ARM: dts: aspeed: yosemite4: fix GPIO linename typo

 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 1749 ++++++++++++++++-
 1 file changed, 1653 insertions(+), 96 deletions(-)

Comments

Andrew Jeffery Aug. 19, 2024, 1:09 a.m. UTC | #1

On Fri, 2024-08-16 at 17:23 +0800, Delphine CC Chiu wrote:
> Changelog:
>   - v12
>     - Fix GPIO linename typo and add missing GPIO pin initial state.

Please make sure to run `./scripts/checkpatch.pl` and `make dtbs_check`
over each patch in your series before sending it. Also, please respond
to review comments. Either acknowledge them and change your work, or
discuss the problems to get consensus on how the changes should
proceed.

Your patches will not be merged if you don't engage with the feedback
from the people reviewing them.

Finally, as it stands, the additions in the series amount to 75% of the
existing devicetree. I feel like it would be more effective to replace
it in a single patch or rename the existing devicetree out of the way,
and not try to maintain a 28-patch series. I assume all these changes
correspond to an iteration of the hardware design rather than some set
of incremental changes in their own right, in which case a new
devicetree seems appropriate.

Andrew