| Message ID | 20240819221051.31489-12-mailingradian@gmail.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add SDM670 camera subsystem | expand |
On 19/08/2024 23:10, Richard Acayan wrote: > Add the camera subsystem and CCI used to interface with cameras on the > Snapdragon 670. > > Signed-off-by: Richard Acayan <mailingradian@gmail.com> > --- > arch/arm64/boot/dts/qcom/sdm670.dtsi | 188 +++++++++++++++++++++++++++ > 1 file changed, 188 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi > index ba93cef33dbb..37bc4fa04286 100644 > --- a/arch/arm64/boot/dts/qcom/sdm670.dtsi > +++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi This looks neater - better indentation for example than what we have for 845 upstream. Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
On 8/20/24 01:10, Richard Acayan wrote: > Add the camera subsystem and CCI used to interface with cameras on the > Snapdragon 670. > > Signed-off-by: Richard Acayan <mailingradian@gmail.com> > --- > arch/arm64/boot/dts/qcom/sdm670.dtsi | 188 +++++++++++++++++++++++++++ > 1 file changed, 188 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi > index ba93cef33dbb..37bc4fa04286 100644 > --- a/arch/arm64/boot/dts/qcom/sdm670.dtsi > +++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi > @@ -6,6 +6,7 @@ > * Copyright (c) 2022, Richard Acayan. All rights reserved. > */ > > +#include <dt-bindings/clock/qcom,camcc-sdm845.h> > #include <dt-bindings/clock/qcom,dispcc-sdm845.h> > #include <dt-bindings/clock/qcom,gcc-sdm845.h> > #include <dt-bindings/clock/qcom,rpmh.h> > @@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 { > gpio-ranges = <&tlmm 0 0 151>; > wakeup-parent = <&pdc>; > > + cci0_default: cci0-default-state { > + pins = "gpio17", "gpio18"; > + function = "cci_i2c"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + cci0_sleep: cci0-sleep-state { > + pins = "gpio17", "gpio18"; > + function = "cci_i2c"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + cci1_default: cci1-default-state { > + pins = "gpio19", "gpio20"; > + function = "cci_i2c"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + cci1_sleep: cci1-sleep-state { > + pins = "gpio19", "gpio20"; > + function = "cci_i2c"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > qup_i2c0_default: qup-i2c0-default-state { > pins = "gpio0", "gpio1"; > function = "qup0"; > @@ -1400,6 +1429,165 @@ spmi_bus: spmi@c440000 { > #interrupt-cells = <4>; > }; > > + cci: cci@ac4a000 { > + compatible = "qcom,sdm670-cci", "qcom,msm8996-cci"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg = <0 0x0ac4a000 0 0x4000>; > + interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>; > + power-domains = <&camcc TITAN_TOP_GDSC>; > + > + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, > + <&camcc CAM_CC_SOC_AHB_CLK>, > + <&camcc CAM_CC_CPAS_AHB_CLK>, > + <&camcc CAM_CC_CCI_CLK>; > + clock-names = "camnoc_axi", > + "soc_ahb", > + "cpas_ahb", > + "cci"; > + > + assigned-clocks = <&camcc CAM_CC_CCI_CLK>; > + assigned-clock-rates = <37500000>; Please remove assigned-clocks and assigned-clock-rates properties. > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&cci0_default &cci1_default>; > + pinctrl-1 = <&cci0_sleep &cci1_sleep>; > + > + status = "disabled"; > + > + cci_i2c0: i2c-bus@0 { > + reg = <0>; > + clock-frequency = <1000000>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + cci_i2c1: i2c-bus@1 { > + reg = <1>; > + clock-frequency = <1000000>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > + camss: camera-controller@ac65000 { > + compatible = "qcom,sdm670-camss"; > + reg = <0 0x0ac65000 0 0x1000>, > + <0 0x0ac66000 0 0x1000>, > + <0 0x0ac67000 0 0x1000>, > + <0 0x0acaf000 0 0x4000>, > + <0 0x0acb3000 0 0x1000>, > + <0 0x0acb6000 0 0x4000>, > + <0 0x0acba000 0 0x1000>, > + <0 0x0acc4000 0 0x4000>, > + <0 0x0acc8000 0 0x1000>; > + reg-names = "csiphy0", > + "csiphy1", > + "csiphy2", > + "vfe0", > + "csid0", > + "vfe1", > + "csid1", > + "vfe_lite", > + "csid2"; > + > + interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "csid0", > + "csid1", > + "csid2", > + "csiphy0", > + "csiphy1", > + "csiphy2", > + "vfe0", > + "vfe1", > + "vfe_lite"; > + > + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, > + <&camcc CAM_CC_CPAS_AHB_CLK>, > + <&camcc CAM_CC_IFE_0_CSID_CLK>, > + <&camcc CAM_CC_IFE_1_CSID_CLK>, > + <&camcc CAM_CC_IFE_LITE_CSID_CLK>, > + <&camcc CAM_CC_CSIPHY0_CLK>, > + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, > + <&camcc CAM_CC_CSIPHY1_CLK>, > + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, > + <&camcc CAM_CC_CSIPHY2_CLK>, > + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, > + <&gcc GCC_CAMERA_AHB_CLK>, > + <&gcc GCC_CAMERA_AXI_CLK>, > + <&camcc CAM_CC_SOC_AHB_CLK>, Please put two &gcc and "soc_ahb" clock sources on top, it will require a change in dt bindings documentation also. > + <&camcc CAM_CC_IFE_0_AXI_CLK>, > + <&camcc CAM_CC_IFE_0_CLK>, > + <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>, > + <&camcc CAM_CC_IFE_1_AXI_CLK>, > + <&camcc CAM_CC_IFE_1_CLK>, > + <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>, > + <&camcc CAM_CC_IFE_LITE_CLK>, > + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>; > + clock-names = "camnoc_axi", > + "cpas_ahb", > + "csi0", > + "csi1", > + "csi2", > + "csiphy0", > + "csiphy0_timer", > + "csiphy1", > + "csiphy1_timer", > + "csiphy2", > + "csiphy2_timer", > + "gcc_camera_ahb", > + "gcc_camera_axi", > + "soc_ahb", > + "vfe0_axi", > + "vfe0", > + "vfe0_cphy_rx", > + "vfe1_axi", > + "vfe1", > + "vfe1_cphy_rx", > + "vfe_lite", > + "vfe_lite_cphy_rx"; > + > + iommus = <&apps_smmu 0x808 0x0>, > + <&apps_smmu 0x810 0x8>, > + <&apps_smmu 0xc08 0x0>, > + <&apps_smmu 0xc10 0x8>; > + > + power-domains = <&camcc IFE_0_GDSC>, > + <&camcc IFE_1_GDSC>, > + <&camcc TITAN_TOP_GDSC>; > + power-domain-names = "ife0", > + "ife1", > + "top"; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + camss_port0: port@0 { > + reg = <0>; > + }; > + > + camss_port1: port@1 { > + reg = <1>; > + }; > + > + camss_port2: port@2 { > + reg = <2>; > + }; > + }; > + }; > + > camcc: clock-controller@ad00000 { > compatible = "qcom,sdm845-camcc"; > reg = <0 0x0ad00000 0 0x10000>; -- Best wishes, Vladimir
On Wed, Aug 21, 2024 at 01:40:14PM +0300, Vladimir Zapolskiy wrote: > On 8/20/24 01:10, Richard Acayan wrote: > > Add the camera subsystem and CCI used to interface with cameras on the > > Snapdragon 670. > > > > Signed-off-by: Richard Acayan <mailingradian@gmail.com> > > --- > > arch/arm64/boot/dts/qcom/sdm670.dtsi | 188 +++++++++++++++++++++++++++ > > 1 file changed, 188 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi > > index ba93cef33dbb..37bc4fa04286 100644 > > --- a/arch/arm64/boot/dts/qcom/sdm670.dtsi > > +++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi > > @@ -6,6 +6,7 @@ > > * Copyright (c) 2022, Richard Acayan. All rights reserved. > > */ > > +#include <dt-bindings/clock/qcom,camcc-sdm845.h> > > #include <dt-bindings/clock/qcom,dispcc-sdm845.h> > > #include <dt-bindings/clock/qcom,gcc-sdm845.h> > > #include <dt-bindings/clock/qcom,rpmh.h> > > @@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 { > > gpio-ranges = <&tlmm 0 0 151>; > > wakeup-parent = <&pdc>; > > + cci0_default: cci0-default-state { > > + pins = "gpio17", "gpio18"; > > + function = "cci_i2c"; > > + drive-strength = <2>; > > + bias-pull-up; > > + }; > > + > > + cci0_sleep: cci0-sleep-state { > > + pins = "gpio17", "gpio18"; > > + function = "cci_i2c"; > > + drive-strength = <2>; > > + bias-pull-down; > > + }; > > + > > + cci1_default: cci1-default-state { > > + pins = "gpio19", "gpio20"; > > + function = "cci_i2c"; > > + drive-strength = <2>; > > + bias-pull-up; > > + }; > > + > > + cci1_sleep: cci1-sleep-state { > > + pins = "gpio19", "gpio20"; > > + function = "cci_i2c"; > > + drive-strength = <2>; > > + bias-pull-down; > > + }; > > + > > qup_i2c0_default: qup-i2c0-default-state { > > pins = "gpio0", "gpio1"; > > function = "qup0"; > > @@ -1400,6 +1429,165 @@ spmi_bus: spmi@c440000 { > > #interrupt-cells = <4>; > > }; > > + cci: cci@ac4a000 { > > + compatible = "qcom,sdm670-cci", "qcom,msm8996-cci"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + reg = <0 0x0ac4a000 0 0x4000>; > > + interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>; > > + power-domains = <&camcc TITAN_TOP_GDSC>; > > + > > + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, > > + <&camcc CAM_CC_SOC_AHB_CLK>, > > + <&camcc CAM_CC_CPAS_AHB_CLK>, > > + <&camcc CAM_CC_CCI_CLK>; > > + clock-names = "camnoc_axi", > > + "soc_ahb", > > + "cpas_ahb", > > + "cci"; > > + > > + assigned-clocks = <&camcc CAM_CC_CCI_CLK>; > > + assigned-clock-rates = <37500000>; > > Please remove assigned-clocks and assigned-clock-rates properties. Doing this adds a warning to dmesg, where the clock rate is set to 19.2 MHz by default. > > + > > + pinctrl-names = "default", "sleep"; > > + pinctrl-0 = <&cci0_default &cci1_default>; > > + pinctrl-1 = <&cci0_sleep &cci1_sleep>; > > + > > + status = "disabled"; > > + > > + cci_i2c0: i2c-bus@0 { > > + reg = <0>; > > + clock-frequency = <1000000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + > > + cci_i2c1: i2c-bus@1 { > > + reg = <1>; > > + clock-frequency = <1000000>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + }; > > + }; > > + > > + camss: camera-controller@ac65000 { > > + compatible = "qcom,sdm670-camss"; > > + reg = <0 0x0ac65000 0 0x1000>, > > + <0 0x0ac66000 0 0x1000>, > > + <0 0x0ac67000 0 0x1000>, > > + <0 0x0acaf000 0 0x4000>, > > + <0 0x0acb3000 0 0x1000>, > > + <0 0x0acb6000 0 0x4000>, > > + <0 0x0acba000 0 0x1000>, > > + <0 0x0acc4000 0 0x4000>, > > + <0 0x0acc8000 0 0x1000>; > > + reg-names = "csiphy0", > > + "csiphy1", > > + "csiphy2", > > + "vfe0", > > + "csid0", > > + "vfe1", > > + "csid1", > > + "vfe_lite", > > + "csid2"; > > + > > + interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "csid0", > > + "csid1", > > + "csid2", > > + "csiphy0", > > + "csiphy1", > > + "csiphy2", > > + "vfe0", > > + "vfe1", > > + "vfe_lite"; > > + > > + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, > > + <&camcc CAM_CC_CPAS_AHB_CLK>, > > + <&camcc CAM_CC_IFE_0_CSID_CLK>, > > + <&camcc CAM_CC_IFE_1_CSID_CLK>, > > + <&camcc CAM_CC_IFE_LITE_CSID_CLK>, > > + <&camcc CAM_CC_CSIPHY0_CLK>, > > + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, > > + <&camcc CAM_CC_CSIPHY1_CLK>, > > + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, > > + <&camcc CAM_CC_CSIPHY2_CLK>, > > + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, > > + <&gcc GCC_CAMERA_AHB_CLK>, > > + <&gcc GCC_CAMERA_AXI_CLK>, > > + <&camcc CAM_CC_SOC_AHB_CLK>, > > Please put two &gcc and "soc_ahb" clock sources on top, it will > require a change in dt bindings documentation also. I'll do this for the clocks themselves because they have no parents (so no obvious clock sources).
On 24/08/2024 00:44, Richard Acayan wrote: >>> + >>> + assigned-clocks = <&camcc CAM_CC_CCI_CLK>; >>> + assigned-clock-rates = <37500000>; >> Please remove assigned-clocks and assigned-clock-rates properties. > Doing this adds a warning to dmesg, where the clock rate is set to 19.2 > MHz by default. I have a patch for this. Feel free to take into your series and then update the dts here. --- bod
diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi index ba93cef33dbb..37bc4fa04286 100644 --- a/arch/arm64/boot/dts/qcom/sdm670.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi @@ -6,6 +6,7 @@ * Copyright (c) 2022, Richard Acayan. All rights reserved. */ +#include <dt-bindings/clock/qcom,camcc-sdm845.h> #include <dt-bindings/clock/qcom,dispcc-sdm845.h> #include <dt-bindings/clock/qcom,gcc-sdm845.h> #include <dt-bindings/clock/qcom,rpmh.h> @@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 { gpio-ranges = <&tlmm 0 0 151>; wakeup-parent = <&pdc>; + cci0_default: cci0-default-state { + pins = "gpio17", "gpio18"; + function = "cci_i2c"; + drive-strength = <2>; + bias-pull-up; + }; + + cci0_sleep: cci0-sleep-state { + pins = "gpio17", "gpio18"; + function = "cci_i2c"; + drive-strength = <2>; + bias-pull-down; + }; + + cci1_default: cci1-default-state { + pins = "gpio19", "gpio20"; + function = "cci_i2c"; + drive-strength = <2>; + bias-pull-up; + }; + + cci1_sleep: cci1-sleep-state { + pins = "gpio19", "gpio20"; + function = "cci_i2c"; + drive-strength = <2>; + bias-pull-down; + }; + qup_i2c0_default: qup-i2c0-default-state { pins = "gpio0", "gpio1"; function = "qup0"; @@ -1400,6 +1429,165 @@ spmi_bus: spmi@c440000 { #interrupt-cells = <4>; }; + cci: cci@ac4a000 { + compatible = "qcom,sdm670-cci", "qcom,msm8996-cci"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0x0ac4a000 0 0x4000>; + interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>; + power-domains = <&camcc TITAN_TOP_GDSC>; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_SOC_AHB_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_CCI_CLK>; + clock-names = "camnoc_axi", + "soc_ahb", + "cpas_ahb", + "cci"; + + assigned-clocks = <&camcc CAM_CC_CCI_CLK>; + assigned-clock-rates = <37500000>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cci0_default &cci1_default>; + pinctrl-1 = <&cci0_sleep &cci1_sleep>; + + status = "disabled"; + + cci_i2c0: i2c-bus@0 { + reg = <0>; + clock-frequency = <1000000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + cci_i2c1: i2c-bus@1 { + reg = <1>; + clock-frequency = <1000000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + camss: camera-controller@ac65000 { + compatible = "qcom,sdm670-camss"; + reg = <0 0x0ac65000 0 0x1000>, + <0 0x0ac66000 0 0x1000>, + <0 0x0ac67000 0 0x1000>, + <0 0x0acaf000 0 0x4000>, + <0 0x0acb3000 0 0x1000>, + <0 0x0acb6000 0 0x4000>, + <0 0x0acba000 0 0x1000>, + <0 0x0acc4000 0 0x4000>, + <0 0x0acc8000 0 0x1000>; + reg-names = "csiphy0", + "csiphy1", + "csiphy2", + "vfe0", + "csid0", + "vfe1", + "csid1", + "vfe_lite", + "csid2"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "vfe0", + "vfe1", + "vfe_lite"; + + clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>, + <&camcc CAM_CC_CPAS_AHB_CLK>, + <&camcc CAM_CC_IFE_0_CSID_CLK>, + <&camcc CAM_CC_IFE_1_CSID_CLK>, + <&camcc CAM_CC_IFE_LITE_CSID_CLK>, + <&camcc CAM_CC_CSIPHY0_CLK>, + <&camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY1_CLK>, + <&camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&camcc CAM_CC_CSIPHY2_CLK>, + <&camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_AXI_CLK>, + <&camcc CAM_CC_SOC_AHB_CLK>, + <&camcc CAM_CC_IFE_0_AXI_CLK>, + <&camcc CAM_CC_IFE_0_CLK>, + <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_1_AXI_CLK>, + <&camcc CAM_CC_IFE_1_CLK>, + <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&camcc CAM_CC_IFE_LITE_CLK>, + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>; + clock-names = "camnoc_axi", + "cpas_ahb", + "csi0", + "csi1", + "csi2", + "csiphy0", + "csiphy0_timer", + "csiphy1", + "csiphy1_timer", + "csiphy2", + "csiphy2_timer", + "gcc_camera_ahb", + "gcc_camera_axi", + "soc_ahb", + "vfe0_axi", + "vfe0", + "vfe0_cphy_rx", + "vfe1_axi", + "vfe1", + "vfe1_cphy_rx", + "vfe_lite", + "vfe_lite_cphy_rx"; + + iommus = <&apps_smmu 0x808 0x0>, + <&apps_smmu 0x810 0x8>, + <&apps_smmu 0xc08 0x0>, + <&apps_smmu 0xc10 0x8>; + + power-domains = <&camcc IFE_0_GDSC>, + <&camcc IFE_1_GDSC>, + <&camcc TITAN_TOP_GDSC>; + power-domain-names = "ife0", + "ife1", + "top"; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + camss_port0: port@0 { + reg = <0>; + }; + + camss_port1: port@1 { + reg = <1>; + }; + + camss_port2: port@2 { + reg = <2>; + }; + }; + }; + camcc: clock-controller@ad00000 { compatible = "qcom,sdm845-camcc"; reg = <0 0x0ad00000 0 0x10000>;
Add the camera subsystem and CCI used to interface with cameras on the Snapdragon 670. Signed-off-by: Richard Acayan <mailingradian@gmail.com> --- arch/arm64/boot/dts/qcom/sdm670.dtsi | 188 +++++++++++++++++++++++++++ 1 file changed, 188 insertions(+)