@@ -336,38 +336,3 @@ void __init dwc2_hsotg_set_platdata(struct dwc2_hsotg_plat *pd)
npd->phy_exit = s3c_usb_phy_exit;
}
#endif /* CONFIG_S3C_DEV_USB_HSOTG */
-
-#ifdef CONFIG_S3C64XX_DEV_SPI0
-static struct resource s3c64xx_spi0_resource[] = {
- [0] = DEFINE_RES_MEM(S3C_PA_SPI0, SZ_256),
- [1] = DEFINE_RES_IRQ(IRQ_SPI0),
-};
-
-struct platform_device s3c64xx_device_spi0 = {
- .name = "s3c6410-spi",
- .id = 0,
- .num_resources = ARRAY_SIZE(s3c64xx_spi0_resource),
- .resource = s3c64xx_spi0_resource,
- .dev = {
- .dma_mask = &samsung_device_dma_mask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-};
-
-void __init s3c64xx_spi0_set_platdata(int src_clk_nr, int num_cs)
-{
- struct s3c64xx_spi_info pd;
-
- /* Reject invalid configuration */
- if (!num_cs || src_clk_nr < 0) {
- pr_err("%s: Invalid SPI configuration\n", __func__);
- return;
- }
-
- pd.num_cs = num_cs;
- pd.src_clk_nr = src_clk_nr;
- pd.cfg_gpio = s3c64xx_spi0_cfg_gpio;
-
- s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi0);
-}
-#endif /* CONFIG_S3C64XX_DEV_SPI0 */
@@ -27,7 +27,6 @@ extern struct platform_device *s3c24xx_uart_src[];
extern struct platform_device s3c64xx_device_iis0;
extern struct platform_device s3c64xx_device_iis1;
-extern struct platform_device s3c64xx_device_spi0;
extern struct platform_device s3c_device_fb;
extern struct platform_device s3c_device_hsmmc0;
@@ -435,7 +435,6 @@ static struct platform_device *crag6410_devs0[] __initdata = {
static struct platform_device *crag6410_devs1[] __initdata = {
&crag6410_dm9k_device,
- &s3c64xx_device_spi0,
&crag6410_mmgpio,
&crag6410_lcd_powerdev,
&crag6410_backlight_device,
@@ -654,22 +653,13 @@ static struct wm831x_pdata crag_pmic_pdata = {
.touch = &touch_pdata,
};
-/*
- * VDDARM is eventually ending up as a regulator hanging on the MFD cell device
- * "wm831x-buckv.1" spawn from drivers/mfd/wm831x-core.c.
- *
- * From the note on the platform data we can see that this is clearly DVS1
- * and assigned as dcdc1 resource to the MFD core which sets .id of the cell
- * spawning the DVS1 platform device to 1, then the cell platform device
- * name is calculated from 10*instance + id resulting in the device name
- * "wm831x-buckv.11"
- */
-static struct gpiod_lookup_table crag_pmic_gpiod_table = {
- .dev_id = "wm831x-buckv.11",
- .table = {
- GPIO_LOOKUP("GPIOK", 0, "dvs", GPIO_ACTIVE_HIGH),
- { },
- },
+static const struct property_entry crag_pmic_properties[] = {
+ PROPERTY_ENTRY_GPIO("dvs-gpios",
+ SAMSUNG_GPIO_NODE('K'), 0, GPIO_ACTIVE_HIGH),
+ { }
+};
+static const struct software_node crag_pmic_swnode = {
+ .properties = crag_pmic_properties,
};
static struct i2c_board_info i2c_devs0[] = {
@@ -680,6 +670,7 @@ static struct i2c_board_info i2c_devs0[] = {
{ I2C_BOARD_INFO("wm8312", 0x34),
.platform_data = &crag_pmic_pdata,
.irq = S3C_EINT(23),
+ .swnode = &crag_pmic_swnode,
},
};
@@ -774,17 +765,22 @@ static struct wm831x_pdata glenfarclas_pmic_pdata = {
.disable_touch = true,
};
-static struct gpiod_lookup_table crag_wm1250_ev1_gpiod_table = {
- /* The WM1250-EV1 is device 0027 on I2C bus 1 */
- .dev_id = "1-0027",
- .table = {
- GPIO_LOOKUP("GPION", 12, "clk-ena", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("GPIOL", 12, "clk-sel0", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("GPIOL", 13, "clk-sel1", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("GPIOL", 14, "osr", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("GPIOL", 8, "master", GPIO_ACTIVE_HIGH),
- { },
- },
+static const struct property_entry crag_wm1250_ev1_properties[] = {
+ PROPERTY_ENTRY_GPIO("clk-ena-gpios",
+ SAMSUNG_GPIO_NODE('N'), 12, GPIO_ACTIVE_HIGH),
+ PROPERTY_ENTRY_GPIO("clk-sel0-gpios",
+ SAMSUNG_GPIO_NODE('L'), 12, GPIO_ACTIVE_HIGH),
+ PROPERTY_ENTRY_GPIO("clk-sel1-gpios",
+ SAMSUNG_GPIO_NODE('L'), 13, GPIO_ACTIVE_HIGH),
+ PROPERTY_ENTRY_GPIO("osr-gpios",
+ SAMSUNG_GPIO_NODE('L'), 14, GPIO_ACTIVE_HIGH),
+ PROPERTY_ENTRY_GPIO("master-gpios",
+ SAMSUNG_GPIO_NODE('L'), 8, GPIO_ACTIVE_HIGH),
+ { }
+};
+
+static const struct software_node crag_wm1250_ev1_swnode = {
+ .properties = crag_wm1250_ev1_properties,
};
static struct i2c_board_info i2c_devs1[] = {
@@ -797,7 +793,8 @@ static struct i2c_board_info i2c_devs1[] = {
{ I2C_BOARD_INFO("wlf-gf-module", 0x24) },
{ I2C_BOARD_INFO("wlf-gf-module", 0x25) },
{ I2C_BOARD_INFO("wlf-gf-module", 0x26) },
- { I2C_BOARD_INFO("wm1250-ev1", 0x27), },
+ { I2C_BOARD_INFO("wm1250-ev1", 0x27),
+ .swnode = &crag_wm1250_ev1_swnode, },
};
static struct s3c2410_platform_i2c i2c1_pdata = {
@@ -887,15 +884,48 @@ static const struct gpio_led_platform_data gpio_leds_pdata = {
static struct dwc2_hsotg_plat crag6410_hsotg_pdata;
-static struct gpiod_lookup_table crag_spi0_gpiod_table = {
- .dev_id = "s3c6410-spi.0",
- .table = {
- GPIO_LOOKUP_IDX("GPIOC", 3, "cs", 0, GPIO_ACTIVE_LOW),
- GPIO_LOOKUP_IDX("GPION", 5, "cs", 1, GPIO_ACTIVE_LOW),
- { },
- },
+static const struct software_node_ref_args crag6410_spi0_gpio_refs[] = {
+ SOFTWARE_NODE_REFERENCE(SAMSUNG_GPIO_NODE('C'), 3, GPIO_ACTIVE_LOW),
+ SOFTWARE_NODE_REFERENCE(SAMSUNG_GPIO_NODE('N'), 5, GPIO_ACTIVE_LOW),
+};
+
+static const struct property_entry crag6410_spi0_properties[] __initconst = {
+ PROPERTY_ENTRY_REF_ARRAY("cs-gpios", crag6410_spi0_gpio_refs),
+ { }
};
+static const struct resource crag6410_spi0_resource[] __initconst = {
+ [0] = DEFINE_RES_MEM(S3C_PA_SPI0, SZ_256),
+ [1] = DEFINE_RES_IRQ(IRQ_SPI0),
+};
+
+static const struct s3c64xx_spi_info crag6410_spi0_platform_data __initconst = {
+ .num_cs = 2,
+ .cfg_gpio = s3c64xx_spi0_cfg_gpio,
+};
+
+static const struct platform_device_info crag6410_spi0_info __initconst = {
+ .name = "s3c6410-spi",
+ .id = 0,
+ .res = crag6410_spi0_resource,
+ .num_res = ARRAY_SIZE(crag6410_spi0_resource),
+ .data = &crag6410_spi0_platform_data,
+ .size_data = sizeof(crag6410_spi0_platform_data),
+ .dma_mask = DMA_BIT_MASK(32),
+ .properties = crag6410_spi0_properties,
+};
+
+static void __init crag6410_setup_spi0(void)
+{
+ struct platform_device *pd;
+ int err;
+
+ pd = platform_device_register_full(&crag6410_spi0_info);
+ err = PTR_ERR_OR_ZERO(pd);
+ if (err)
+ pr_err("failed to create spi0 device: %d\n", err);
+}
+
static void __init crag6410_machine_init(void)
{
/* Open drain IRQs need pullups */
@@ -922,19 +952,15 @@ static void __init crag6410_machine_init(void)
s3c_fb_set_platdata(&crag6410_lcd_pdata);
dwc2_hsotg_set_platdata(&crag6410_hsotg_pdata);
- gpiod_add_lookup_table(&crag_pmic_gpiod_table);
i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
- gpiod_add_lookup_table(&crag_wm1250_ev1_gpiod_table);
i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
- gpiod_add_lookup_table(&crag_spi0_gpiod_table);
- s3c64xx_spi0_set_platdata(0, 2);
-
pwm_add_table(crag6410_pwm_lookup, ARRAY_SIZE(crag6410_pwm_lookup));
platform_add_devices(crag6410_devs0, ARRAY_SIZE(crag6410_devs0));
crag6410_setup_keypad();
crag6410_setup_gpio_keys();
+ crag6410_setup_spi0();
platform_add_devices(crag6410_devs1, ARRAY_SIZE(crag6410_devs1));
Static property entries support defining GPIOs and are more similar to device tree properties and are not prone to losing link between device and a lookup table because of changes in device name. Convert the board to use them. This also fixes issue with recent conversion to GPIO descriptors where GPIO lookup tables were specifying incorrect GPIO chip name ("GPIO<N>" vs "GP<N>"). Fixes: 10a366f36e2a ("ASoC: wm1250-ev1: Convert to GPIO descriptors") Fixes: a45cf3cc72dd ("spi: s3c64xx: Convert to use GPIO descriptors") Fixes: 9a5ed0bac86e ("regulator: wm831x: Convert to use GPIO descriptors") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> --- arch/arm/mach-s3c/devs.c | 35 ---------- arch/arm/mach-s3c/devs.h | 1 - arch/arm/mach-s3c/mach-crag6410.c | 108 ++++++++++++++++++------------ 3 files changed, 67 insertions(+), 77 deletions(-)