@@ -5889,6 +5889,11 @@ S: Maintained
F: Documentation/filesystems/cramfs.rst
F: fs/cramfs/
+CRAY CLUSTERSTOR E1000 NVME SLOT LED DRIVER
+M: Tony Hutter <hutter2@llnl.gov>
+S: Maintained
+F: drivers/pci/hotplug/pciehp_craye1k.c
+
CREATIVE SB0540
M: Bastien Nocera <hadess@hadess.net>
L: linux-input@vger.kernel.org
@@ -173,4 +173,16 @@ config HOTPLUG_PCI_S390
When in doubt, say Y.
+config HOTPLUG_PCI_PCIE_CRAY_E1000
+ tristate "PCIE Hotplug extensions for Cray ClusterStor E1000"
+ depends on ACPI_PCI_SLOT && HOTPLUG_PCI_PCIE && IPMI_HANDLER
+ help
+ Say Y here if you have a Cray ClusterStor E1000 and want to control
+ your NVMe slot LEDs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called pciehp_craye1k.
+
+ When in doubt, say N.
+
endif # HOTPLUG_PCI
@@ -65,6 +65,7 @@ pciehp-objs := pciehp_core.o \
pciehp_ctrl.o \
pciehp_pci.o \
pciehp_hpc.o
+obj-$(CONFIG_HOTPLUG_PCI_PCIE_CRAY_E1000) += pciehp_craye1k.o
shpchp-objs := shpchp_core.o \
shpchp_ctrl.o \
new file mode 100644
@@ -0,0 +1,928 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2022-2024 Lawrence Livermore National Security, LLC
+ */
+/*
+ * Cray ClusterStor E1000 hotplug slot LED driver
+ *
+ * This driver controls the NVMe slot LEDs on the Cray ClusterStore E1000.
+ * It provides hotplug attention status callbacks for the 24 NVMe slots on
+ * the E1000. This allows users to access the E1000's locate and fault
+ * LEDs via the normal /sys/bus/pci/slots/<slot>/attention sysfs entries.
+ * This driver uses IPMI to communicate with the E1000 controller to toggle
+ * the LEDs.
+ *
+ * This driver is based off of ibmpex.c
+ */
+
+#include <linux/delay.h>
+#include <linux/dmi.h>
+#include <linux/ipmi.h>
+#include <linux/ipmi_smi.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/pci_hotplug.h>
+#include <linux/random.h>
+#include "pciehp.h"
+
+/* Cray E1000 commands */
+#define CRAYE1K_CMD_NETFN 0x3c
+#define CRAYE1K_CMD_PRIMARY 0x33
+#define CRAYE1K_CMD_FAULT_LED 0x39
+#define CRAYE1K_CMD_LOCATE_LED 0x22
+
+/* Subcommands */
+#define CRAYE1K_GET_LED 0x0
+#define CRAYE1K_SET_LED 0x1
+#define CRAYE1K_SET_PRIMARY 0x1
+
+static bool print_errors;
+module_param(print_errors, bool, 0644);
+MODULE_PARM_DESC(print_errors, "Print info on spurious IPMI messages");
+
+static int ipmi_retries;
+module_param(ipmi_retries, int, 0644);
+MODULE_PARM_DESC(ipmi_retries,
+ "Retries for kernel IPMI layer (-1 = use default_max_retries)");
+
+static int ipmi_timeout = 500;
+module_param(ipmi_timeout, int, 0644);
+MODULE_PARM_DESC(ipmi_timeout,
+ "Timeout in ms for IPMI (0 = use IPMI default_retry_ms)");
+
+static int completion_timeout = 500;
+module_param(completion_timeout, int, 0644);
+MODULE_PARM_DESC(completion_timeout,
+ "Timeout in ms to wait for E1000 message completion");
+
+struct craye1k {
+ struct device *dev; /* BMC device */
+ struct mutex lock;
+ struct completion read_complete;
+ struct ipmi_addr address;
+ struct ipmi_user *user;
+ int iface;
+
+ long tx_msg_id;
+ struct kernel_ipmi_msg tx_msg;
+ unsigned char tx_msg_data[IPMI_MAX_MSG_LENGTH];
+
+ unsigned char rx_msg_data[IPMI_MAX_MSG_LENGTH];
+ unsigned long rx_msg_len;
+ unsigned char rx_result; /* IPMI completion code */
+
+ /*
+ * Record the original set_attention_status()/get_attention_status()
+ * callbacks for the 24 ports so that we can restore them when we
+ * remove the module.
+ */
+ const struct hotplug_slot_ops *orig_ops[24];
+ struct hotplug_slot_ops new_ops[24];
+
+ /*
+ * Debugging stats: /sys/class/ipmi/ipmi0/device/craye1k_stats/
+ */
+ atomic64_t check_primary;
+ atomic64_t check_primary_failed;
+ atomic64_t was_already_primary;
+ atomic64_t was_not_already_primary;
+ atomic64_t set_primary;
+ atomic64_t set_initial_primary_failed;
+ atomic64_t set_primary_failed;
+ atomic64_t set_led_locate_failed;
+ atomic64_t set_led_fault_failed;
+ atomic64_t set_led_readback_failed;
+ atomic64_t set_led_failed;
+ atomic64_t get_led_failed;
+ atomic64_t completion_timeout;
+ atomic64_t wrong_msgid;
+ atomic64_t request_failed;
+};
+
+static ssize_t craye1k_show(struct kobject *kobj, struct kobj_attribute *kattr,
+ char *buf);
+static ssize_t craye1k_store(struct kobject *kobj, struct kobj_attribute *kattr,
+ const char *buf,
+ size_t count);
+static void craye1k_new_smi(int iface, struct device *dev);
+static void craye1k_smi_gone(int iface);
+static void craye1k_msg_handler(struct ipmi_recv_msg *msg, void *user_msg_data);
+
+struct craye1k_driver_data {
+ struct ipmi_smi_watcher smi_watcher;
+ struct ipmi_user_hndl user_hndl;
+ struct craye1k *craye1k;
+};
+
+static struct craye1k_driver_data craye1k_driver_data = {
+ .smi_watcher = {
+ .owner = THIS_MODULE,
+ .new_smi = craye1k_new_smi,
+ .smi_gone = craye1k_smi_gone
+ },
+ .user_hndl = {
+ .ipmi_recv_hndl = craye1k_msg_handler,
+ },
+ .craye1k = NULL,
+};
+
+static const struct kobj_attribute craye1k_kattr[] = {
+ __ATTR(check_primary, 0660, craye1k_show, craye1k_store),
+ __ATTR(check_primary_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(was_already_primary, 0660, craye1k_show, craye1k_store),
+ __ATTR(was_not_already_primary, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_primary, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_initial_primary_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_primary_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_led_locate_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_led_fault_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_led_readback_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(set_led_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(get_led_failed, 0660, craye1k_show, craye1k_store),
+ __ATTR(completion_timeout, 0660, craye1k_show, craye1k_store),
+ __ATTR(wrong_msgid, 0660, craye1k_show, craye1k_store),
+ __ATTR(request_failed, 0660, craye1k_show, craye1k_store),
+};
+
+/*
+ * The individual craye1k_attrs[] entries get initialized in
+ * craye1k_create_sysfs.
+ *
+ * The last craye1k_attrs[] entry is for the NULL terminator.
+ */
+static struct attribute *craye1k_kattrs[ARRAY_SIZE(craye1k_kattr) + 1] = {0};
+static struct attribute_group craye1k_group = {
+ .attrs = craye1k_kattrs,
+ .name = "craye1k_stats"
+};
+
+#define CRAYE1K_TABLE(_name) { \
+ .name = __stringify(_name), \
+ .offset = offsetof(struct craye1k, _name) \
+}
+
+/* Given a kobj_attribute for the stat, return a pointer to its stat value */
+static atomic64_t *craye1k_lookup_stat(struct kobject *kobj, const char *name)
+{
+ struct craye1k *craye1k;
+ struct device *dev;
+ int i;
+
+ /* Lookup table for name -> atomic64_t offset */
+ const struct {
+ const char *name;
+ size_t offset;
+ } table[] = {
+ CRAYE1K_TABLE(check_primary),
+ CRAYE1K_TABLE(check_primary_failed),
+ CRAYE1K_TABLE(was_already_primary),
+ CRAYE1K_TABLE(was_not_already_primary),
+ CRAYE1K_TABLE(set_primary),
+ CRAYE1K_TABLE(set_initial_primary_failed),
+ CRAYE1K_TABLE(set_primary_failed),
+ CRAYE1K_TABLE(set_led_locate_failed),
+ CRAYE1K_TABLE(set_led_fault_failed),
+ CRAYE1K_TABLE(set_led_readback_failed),
+ CRAYE1K_TABLE(set_led_failed),
+ CRAYE1K_TABLE(get_led_failed),
+ CRAYE1K_TABLE(completion_timeout),
+ CRAYE1K_TABLE(wrong_msgid),
+ CRAYE1K_TABLE(request_failed)
+ };
+
+ dev = container_of(kobj, struct device, kobj);
+ craye1k = dev_get_drvdata(dev);
+
+ /* lookup atomic64_t from name */
+ for (i = 0; i < ARRAY_SIZE(table); i++)
+ if (strcmp(table[i].name, name) == 0)
+ return (atomic64_t *)((char *)craye1k + table[i].offset);
+
+ return NULL;
+}
+
+static int craye1k_create_sysfs(struct craye1k *craye1k)
+{
+ int i;
+ atomic64_t *a;
+
+ /*
+ * Fill in craye1k_kattrs[] with the pointers to our kobj_attributes.
+ */
+ for (i = 0; i < ARRAY_SIZE(craye1k_kattrs) - 1; i++) {
+ craye1k_kattrs[i] = (struct attribute *)&craye1k_kattr[i].attr;
+
+ /* For completeness, initialize all atomics to 0 */
+ a = craye1k_lookup_stat(&craye1k->dev->kobj,
+ craye1k_kattr[i].attr.name);
+ atomic64_set(a, 0);
+ }
+
+ craye1k_kattrs[i] = NULL; /* mark end of the list */
+
+ return sysfs_create_group(&craye1k->dev->kobj, &craye1k_group);
+}
+
+static void craye1k_remove_sysfs(struct craye1k *craye1k)
+{
+ sysfs_remove_group(&craye1k->dev->kobj, &craye1k_group);
+}
+
+static ssize_t craye1k_show(struct kobject *kobj, struct kobj_attribute *kattr,
+ char *buf)
+{
+ atomic64_t *val;
+
+ val = craye1k_lookup_stat(kobj, kattr->attr.name);
+ if (!val)
+ return -EINVAL;
+
+ return sprintf(buf, "%llu\n", atomic64_read(val));
+}
+
+/* A write of anything clears counter */
+static ssize_t craye1k_store(struct kobject *kobj, struct kobj_attribute *kattr,
+ const char *buf, size_t count)
+{
+ atomic64_t *val;
+
+ val = craye1k_lookup_stat(kobj, kattr->attr.name);
+ if (!val)
+ return -EINVAL;
+
+ atomic64_set(val, 0);
+
+ return count;
+}
+
+/*
+ * craye1k_msg_handler() - IPMI message response handler
+ */
+static void craye1k_msg_handler(struct ipmi_recv_msg *msg, void *user_msg_data)
+{
+ struct craye1k *craye1k = user_msg_data;
+
+ WARN_ON(craye1k != craye1k_driver_data.craye1k);
+
+ if (msg->msgid != craye1k->tx_msg_id) {
+ atomic64_inc(&craye1k->wrong_msgid);
+ if (print_errors) {
+ dev_warn_ratelimited(craye1k->dev, "rx msgid %d != %d",
+ (int)msg->msgid,
+ (int)craye1k->tx_msg_id);
+ }
+ ipmi_free_recv_msg(msg);
+ return;
+ }
+
+ /* Set rx_result to the IPMI completion code */
+ if (msg->msg.data_len > 0)
+ craye1k->rx_result = msg->msg.data[0];
+ else
+ craye1k->rx_result = IPMI_UNKNOWN_ERR_COMPLETION_CODE;
+
+ if (msg->msg.data_len > 1) {
+ /* Exclude completion code from data bytes */
+ craye1k->rx_msg_len = msg->msg.data_len - 1;
+ memcpy(craye1k->rx_msg_data, msg->msg.data + 1,
+ craye1k->rx_msg_len);
+ } else {
+ craye1k->rx_msg_len = 0;
+ }
+
+ ipmi_free_recv_msg(msg);
+ complete(&craye1k->read_complete);
+}
+
+/*
+ * craye1k_send_message() - Send the message already setup in 'craye1k'
+ *
+ * Context: craye1k->lock is already held.
+ * Return: 0 on success, non-zero on error.
+ */
+static int craye1k_send_message(struct craye1k *craye1k)
+{
+ int rc;
+
+ rc = ipmi_validate_addr(&craye1k->address, sizeof(craye1k->address));
+ if (rc) {
+ dev_err_ratelimited(craye1k->dev, "validate_addr() = %d\n", rc);
+ return rc;
+ }
+
+ craye1k->tx_msg_id++;
+
+ rc = ipmi_request_settime(craye1k->user, &craye1k->address,
+ craye1k->tx_msg_id, &craye1k->tx_msg, craye1k,
+ 0, ipmi_retries, ipmi_timeout);
+ if (rc) {
+ atomic64_inc(&craye1k->request_failed);
+ return rc;
+ }
+
+ return 0;
+}
+
+/*
+ * craye1k_do_message() - Send the message in 'craye1k' and wait for a response
+ *
+ * Context: craye1k->lock is already held.
+ * Return: 0 on success, non-zero on error.
+ */
+static int craye1k_do_message(struct craye1k *craye1k)
+{
+ int rc;
+ long rc2;
+ struct completion *read_complete = &craye1k->read_complete;
+ unsigned long tout = msecs_to_jiffies(completion_timeout);
+
+ rc = craye1k_send_message(craye1k);
+ if (rc == 0) {
+ rc2 = wait_for_completion_killable_timeout(read_complete, tout);
+ if (rc2 == 0) {
+ atomic64_inc(&craye1k->completion_timeout);
+ rc = -ETIME;
+ }
+ }
+
+ if (craye1k->rx_result == IPMI_UNKNOWN_ERR_COMPLETION_CODE || rc2 <= 0)
+ rc = -1;
+
+ return rc;
+}
+
+/*
+ * __craye1k_do_command() - Do an IPMI command
+ *
+ * Send a command with optional data bytes, and read back response bytes.
+ * Context: craye1k->lock is already held.
+ * Returns: 0 on success, non-zero on error.
+ */
+static int __craye1k_do_command(struct craye1k *craye1k, u8 netfn, u8 cmd,
+ u8 *send_data, u8 send_data_len, u8 *recv_data,
+ u8 recv_data_len)
+{
+ int rc;
+
+ craye1k->tx_msg.netfn = netfn;
+ craye1k->tx_msg.cmd = cmd;
+
+ if (send_data) {
+ memcpy(&craye1k->tx_msg_data[0], send_data, send_data_len);
+ craye1k->tx_msg.data_len = send_data_len;
+ } else {
+ craye1k->tx_msg_data[0] = 0;
+ craye1k->tx_msg.data_len = 0;
+ }
+
+ rc = craye1k_do_message(craye1k);
+ memcpy(recv_data, craye1k->rx_msg_data, recv_data_len);
+
+ return rc;
+}
+
+/*
+ * craye1k_do_command_and_netfn() - Do IPMI command and return 1st data byte
+ *
+ * Do an IPMI command with the given netfn, cmd, and optional send payload
+ * bytes.
+ *
+ * Context: craye1k->lock is already held.
+ * Returns: the last byte from the response or 0 if response had no response
+ * data bytes, else -1 on error.
+ */
+static int craye1k_do_command_and_netfn(struct craye1k *craye1k, u8 netfn,
+ u8 cmd, u8 *send_data, u8 send_data_len)
+{
+ int rc;
+
+ rc = __craye1k_do_command(craye1k, netfn, cmd, send_data, send_data_len,
+ NULL, 0);
+ if (rc != 0) {
+ /* Error attempting command */
+ return -1;
+ }
+
+ if (craye1k->tx_msg.data_len == 0)
+ return 0;
+
+ /* Return last received byte value */
+ return craye1k->rx_msg_data[craye1k->rx_msg_len - 1];
+}
+
+/*
+ * craye1k_do_command() - Do a Cray E1000 specific IPMI command.
+ * @cmd: Cray E1000 specific command
+ * @send_data: Data to send after the command
+ * @send_data_len: Data length
+ *
+ * Returns: the last byte from the response or 0 if response had no response
+ * data bytes, else -1 on error.
+ */
+static int craye1k_do_command(struct craye1k *craye1k, u8 cmd, u8 *send_data,
+ u8 send_data_len)
+{
+ int rc;
+
+ if (mutex_lock_interruptible(&craye1k->lock) != 0)
+ return -1;
+
+ rc = craye1k_do_command_and_netfn(craye1k, CRAYE1K_CMD_NETFN, cmd,
+ send_data, send_data_len);
+
+ mutex_unlock(&craye1k->lock);
+
+ return rc;
+}
+
+/*
+ * __craye1k_set_primary() - Tell the BMC we want to be the primary server
+ *
+ * An E1000 board has two physical servers on it. In order to set a slot
+ * NVMe LED, this server needs to first tell the BMC that it's the primary
+ * server.
+ *
+ * Returns: 0 on success, 1 otherwise.
+ */
+
+static int __craye1k_set_primary(struct craye1k *craye1k)
+{
+ u8 bytes[2] = {CRAYE1K_SET_PRIMARY, 1}; /* set primary to 1 */
+ int rc;
+
+ atomic64_inc(&craye1k->set_primary);
+ rc = craye1k_do_command(craye1k, CRAYE1K_CMD_PRIMARY, bytes, 2);
+ if (rc == -1)
+ return 1;
+
+ return 0;
+}
+
+/*
+ * craye1k_is_primary() - Are we the primary server?
+ *
+ * Returns: 1 if we are the primary server, 0 otherwise.
+ */
+static int craye1k_is_primary(struct craye1k *craye1k)
+{
+ u8 byte = 0;
+ int rc;
+
+ /* Response byte is 0x1 on success */
+ rc = craye1k_do_command(craye1k, CRAYE1K_CMD_PRIMARY, &byte, 1);
+ atomic64_inc(&craye1k->check_primary);
+ if (rc == 0x1)
+ return 1; /* success */
+
+ atomic64_inc(&craye1k->check_primary_failed);
+ return 0; /* We are not the primary server node */
+}
+
+/*
+ * craye1k_set_primary() - Attempt to set ourselves as the primary server
+ *
+ * Returns: 0 on success, 1 otherwise.
+ */
+static int craye1k_set_primary(struct craye1k *craye1k)
+{
+ int tries = 10;
+
+ if (craye1k_is_primary(craye1k)) {
+ atomic64_inc(&craye1k->was_already_primary);
+ return 0;
+ }
+ atomic64_inc(&craye1k->was_not_already_primary);
+
+ if (__craye1k_set_primary(craye1k) != 0) {
+ atomic64_inc(&craye1k->set_initial_primary_failed);
+ return 1; /* error */
+ }
+
+ /*
+ * It can take 2 to 3 seconds after setting primary for the controller
+ * to report that it is the primary.
+ */
+ while (tries--) {
+ msleep(500);
+ if (craye1k_is_primary(craye1k))
+ break;
+ }
+
+ if (tries == 0) {
+ atomic64_inc(&craye1k->set_primary_failed);
+ return 1; /* never reported that it's primary */
+ }
+
+ /* Wait for primary switch to finish */
+ msleep(1500);
+
+ return 0;
+}
+
+/*
+ * craye1k_get_slot_led() - Get slot LED value
+ * @slot: Slot number (1-24)
+ * @is_locate_led: 0 = get fault LED value, 1 = get locate LED value
+ *
+ * Returns: slot value on success, -1 on failure.
+ */
+static int craye1k_get_slot_led(struct craye1k *craye1k, unsigned char slot,
+ bool is_locate_led)
+{
+ u8 bytes[2];
+ u8 cmd;
+
+ bytes[0] = CRAYE1K_GET_LED;
+ bytes[1] = slot;
+
+ cmd = is_locate_led ? CRAYE1K_CMD_LOCATE_LED : CRAYE1K_CMD_FAULT_LED;
+
+ return craye1k_do_command(craye1k, cmd, bytes, 2);
+}
+
+/*
+ * craye1k_set_slot_led() - Attempt to set the locate/fault LED to a value
+ * @slot: Slot number (1-24)
+ * @is_locate_led: 0 = use fault LED, 1 = use locate LED
+ * @value: Value to set (0 or 1)
+ *
+ * Check the LED value after calling this function to ensure it has been set
+ * properly.
+ *
+ * Returns: 0 on success, 1 on failure.
+ */
+static int craye1k_set_slot_led(struct craye1k *craye1k, unsigned char slot,
+ unsigned char is_locate_led,
+ unsigned char value)
+{
+ int rc;
+ u8 bytes[3];
+
+ bytes[0] = CRAYE1K_SET_LED;
+ bytes[1] = slot;
+ bytes[2] = value;
+
+ if (is_locate_led)
+ rc = craye1k_do_command(craye1k, CRAYE1K_CMD_LOCATE_LED, bytes,
+ 3);
+ else
+ rc = craye1k_do_command(craye1k, CRAYE1K_CMD_FAULT_LED, bytes, 3);
+
+ if (rc == -1) {
+ /* Error setting LED - let higher level retries deal with it */
+ return 1;
+ }
+
+ return 0;
+}
+
+static struct craye1k *craye1k_from_hotplug_slot(struct hotplug_slot
+ *hotplug_slot)
+{
+ unsigned char slot;
+ const struct hotplug_slot_ops *ops;
+ struct craye1k *craye1k;
+
+ slot = PSN(to_ctrl(hotplug_slot));
+
+ /*
+ * We know that our attention status callback functions have been swapped
+ * into the PCI device's hotplug_slot->ops values. We can use that
+ * knowledge to lookup our craye1k.
+ *
+ * To do that, we use the current hotplug_slot->ops value, which is going
+ * to be one of the entries in craye1k->ops[], and offset our slot number
+ * to get the address of craye1k->ops[0]. We then use that with
+ * container_of() to get craye1k. Slots start at 1, so account for that.
+ */
+ ops = hotplug_slot->ops + 1 - slot;
+ craye1k = container_of(ops, struct craye1k, new_ops[0]);
+
+ return craye1k;
+}
+
+static int __craye1k_get_attention_status(struct hotplug_slot *hotplug_slot,
+ u8 *status, bool set_primary)
+{
+ unsigned char slot;
+ int locate, fault;
+ int rc = 0;
+ struct craye1k *craye1k;
+
+ slot = PSN(to_ctrl(hotplug_slot));
+ if (!(slot >= 1 && slot <= 24)) {
+ rc = -EINVAL;
+ goto out;
+ }
+
+ craye1k = craye1k_from_hotplug_slot(hotplug_slot);
+
+ if (set_primary) {
+ if (craye1k_set_primary(craye1k) != 0) {
+ rc = -EIO;
+ goto out;
+ }
+ }
+
+ locate = craye1k_get_slot_led(craye1k, slot, true);
+ if (locate == -1) {
+ rc = -EINVAL;
+ goto out;
+ }
+
+ fault = craye1k_get_slot_led(craye1k, slot, false);
+ if (fault == -1) {
+ rc = -EINVAL;
+ goto out;
+ }
+
+ if (rc != 0)
+ atomic64_inc(&craye1k->get_led_failed);
+
+ *status = locate << 1 | fault;
+
+out:
+ return rc;
+}
+
+static int craye1k_get_attention_status(struct hotplug_slot *hotplug_slot,
+ u8 *status)
+{
+ return __craye1k_get_attention_status(hotplug_slot, status, true);
+}
+
+static int craye1k_set_attention_status(struct hotplug_slot *hotplug_slot,
+ u8 status)
+{
+ unsigned char slot;
+ int tries = 4;
+ int rc;
+ u8 new_status;
+ struct craye1k *craye1k;
+ bool locate, fault;
+
+ slot = PSN(to_ctrl(hotplug_slot));
+ if (!(slot >= 1 && slot <= 24))
+ return -EINVAL;
+
+ craye1k = craye1k_from_hotplug_slot(hotplug_slot);
+
+ /* Retry to ensure all LEDs are set */
+ while (tries--) {
+ /*
+ * The node must first set itself to be the primary node before
+ * setting the slot LEDs (each board has two nodes, or
+ * "servers" as they're called by the manufacturer). This can
+ * lead to contention if both nodes are trying to set the LEDs
+ * at the same time.
+ */
+ rc = craye1k_set_primary(craye1k);
+ if (rc != 0) {
+ /* Could not set as primary node. Just retry again. */
+ continue;
+ }
+
+ /* locate */
+ locate = (status & 0x2) >> 1;
+ if (craye1k_set_slot_led(craye1k, slot, 1, locate) != 0) {
+ atomic64_inc(&craye1k->set_led_locate_failed);
+ continue; /* fail, retry */
+ }
+
+ /* fault */
+ fault = status & 0x1;
+ if (craye1k_set_slot_led(craye1k, slot, 0, fault) != 0) {
+ atomic64_inc(&craye1k->set_led_fault_failed);
+ continue; /* fail, retry */
+ }
+
+ rc = __craye1k_get_attention_status(hotplug_slot, &new_status,
+ false);
+ if (rc == 0 && new_status == status)
+ break; /* success */
+
+ atomic64_inc(&craye1k->set_led_readback_failed);
+
+ /*
+ * At this point we weren't successful in setting the LED and
+ * need to try again.
+ *
+ * Do a random back-off to reduce contention with other server
+ * node in the unlikely case that both server nodes are trying to
+ * trying to set a LED at the same time.
+ *
+ * The 500ms minimum in the backoff reduced the chance of this
+ * whole retry loop failing from 1 in 700 to none in 10000.
+ */
+ msleep(500 + (get_random_long() % 500));
+ }
+
+ if (tries == 0) {
+ atomic64_inc(&craye1k->set_led_failed);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/*
+ * Returns the hotplug controller for a given pci_dev (if any).
+ */
+static struct controller *craye1k_pci_dev_to_ctrl(struct pci_dev *dev)
+{
+ struct device *device;
+ struct pcie_device *edev;
+ struct controller *ctrl;
+
+ device = pcie_port_find_device(dev, PCIE_PORT_SERVICE_HP);
+ if (!device)
+ return NULL;
+
+ edev = to_pcie_device(device);
+ if (!edev)
+ return NULL;
+
+ ctrl = get_service_data(edev);
+ if (!ctrl)
+ return NULL;
+
+ return ctrl;
+}
+
+/*
+ * Update the hotplug 'attention' callbacks to point to craye1k's callbacks.
+ */
+static void craye1k_setup_attention_callbacks(struct craye1k *craye1k)
+{
+ struct pci_dev *dev = NULL;
+ const struct hotplug_slot_ops *ops;
+ struct hotplug_slot_ops *new_ops;
+ struct controller *ctrl;
+ unsigned char slot;
+
+ /*
+ * Iterate though all the PCI devices looking for the ones controlled
+ * by the pciehp driver.
+ */
+ for_each_pci_dev(dev) {
+ ctrl = craye1k_pci_dev_to_ctrl(dev);
+ if (!ctrl) /* not controlled by pciehp */
+ continue;
+
+ /* craye1k slots are numbered 1-24 */
+ slot = PSN(ctrl);
+ if (!(slot >= 1 && slot <= 24))
+ continue;
+
+ mutex_lock(&ctrl->state_lock);
+ /*
+ * Save old hotplug ops callbacks for restoration when
+ * we unload the driver.
+ *
+ * Note: the craye1k slots are numbered starting at 1, not 0.
+ */
+ ops = ctrl->hotplug_slot.ops;
+ craye1k->orig_ops[slot - 1] = ops;
+
+ /*
+ * 'ops' is const, so we can't just go in and change
+ * ctrl->hotplug_slot.ops.[get|set]_attention_status to
+ * point to our callbacks. Instead we make a copy of ops,
+ * update our callbacks in it, and point ctrl->hotplug_slot.ops
+ * to our new 'ops'.
+ */
+ new_ops = &craye1k->new_ops[slot - 1];
+ memcpy(new_ops, ops, sizeof(*ops));
+ mutex_unlock(&ctrl->state_lock);
+
+ new_ops->set_attention_status = craye1k_set_attention_status;
+ new_ops->get_attention_status = craye1k_get_attention_status;
+
+ /*
+ * Re-generate sysfs entry for our ops. In this case, it will
+ * add our 'attention' sysfs entry for slots 1-24.
+ */
+ pci_hp_del(&ctrl->hotplug_slot);
+
+ mutex_lock(&ctrl->state_lock);
+ ctrl->hotplug_slot.ops = new_ops;
+ mutex_unlock(&ctrl->state_lock);
+
+ pci_hp_add(&ctrl->hotplug_slot);
+ }
+}
+
+static void craye1k_restore_attention_callbacks(struct craye1k *craye1k)
+{
+ struct pci_dev *dev = NULL;
+ unsigned char slot;
+ struct controller *ctrl;
+
+ for_each_pci_dev(dev) {
+ ctrl = craye1k_pci_dev_to_ctrl(dev);
+ if (!ctrl)
+ continue;
+
+ slot = PSN(ctrl);
+ if (!(slot >= 1 && slot <= 24))
+ continue;
+
+ pci_hp_del(&ctrl->hotplug_slot);
+
+ mutex_lock(&ctrl->state_lock);
+ ctrl->hotplug_slot.ops = craye1k->orig_ops[slot - 1];
+ mutex_unlock(&ctrl->state_lock);
+
+ pci_hp_add(&ctrl->hotplug_slot);
+ }
+}
+
+static void craye1k_new_smi(int iface, struct device *dev)
+{
+ int rc;
+ struct craye1k *craye1k;
+
+ WARN_ON(craye1k_driver_data.craye1k);
+
+ craye1k = kzalloc(sizeof(*craye1k), GFP_KERNEL);
+ if (!craye1k)
+ return;
+
+ craye1k->address.addr_type = IPMI_SYSTEM_INTERFACE_ADDR_TYPE;
+ craye1k->address.channel = IPMI_BMC_CHANNEL;
+ craye1k->iface = iface;
+ craye1k->dev = dev;
+ craye1k->tx_msg.data = craye1k->tx_msg_data;
+ init_completion(&craye1k->read_complete);
+ mutex_init(&craye1k->lock);
+
+ dev_set_drvdata(dev, craye1k);
+ craye1k_driver_data.craye1k = craye1k;
+
+ rc = ipmi_create_user(craye1k->iface, &craye1k_driver_data.user_hndl,
+ craye1k, &craye1k->user);
+ if (rc < 0) {
+ dev_err_ratelimited(dev,
+ "Unable to register IPMI user, iface %d\n",
+ craye1k->iface);
+ kfree(craye1k);
+ craye1k = NULL;
+ } else {
+ craye1k_setup_attention_callbacks(craye1k);
+ }
+ if (craye1k_create_sysfs(craye1k) != 0)
+ dev_err_ratelimited(dev, "Couldn't create sysfs entries");
+
+ dev_info_ratelimited(dev, "Cray ClusterStor E1000 slot LEDs registered");
+}
+
+static void craye1k_cleanup(struct craye1k *craye1k)
+{
+ if (craye1k) {
+ craye1k_remove_sysfs(craye1k);
+ craye1k_restore_attention_callbacks(craye1k);
+ ipmi_destroy_user(craye1k->user);
+ craye1k_driver_data.craye1k = NULL;
+ kfree(craye1k);
+ }
+}
+
+static void craye1k_smi_gone(int iface)
+{
+ struct craye1k *craye1k = craye1k_driver_data.craye1k;
+
+ if (craye1k->iface != iface)
+ return;
+
+ craye1k_cleanup(craye1k);
+}
+
+static bool is_craye1k_board(void)
+{
+ return dmi_match(DMI_PRODUCT_NAME, "VSSEP1EC");
+}
+
+static int craye1k_init(void)
+{
+ if (!is_craye1k_board())
+ return 0;
+
+ return ipmi_smi_watcher_register(&craye1k_driver_data.smi_watcher);
+}
+
+static void craye1k_exit(void)
+{
+ if (!is_craye1k_board())
+ return;
+
+ ipmi_smi_watcher_unregister(&craye1k_driver_data.smi_watcher);
+ craye1k_cleanup(craye1k_driver_data.craye1k);
+}
+
+MODULE_SOFTDEP("pre: pciehp");
+
+module_init(craye1k_init);
+module_exit(craye1k_exit);
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Tony Hutter <hutter2@llnl.gov>");
+MODULE_DESCRIPTION("Cray E1000 NVMe Slot LED driver");
Add driver to control the NVMe slot LEDs on the Cray ClusterStor E1000. The driver provides hotplug attention status callbacks for the 24 NVMe slots on the E1000. This allows users to access the E1000's locate and fault LEDs via the normal /sys/bus/pci/slots/<slot>/attention sysfs entries. This driver uses IPMI to communicate with the E1000 controller to toggle the LEDs. Signed-off-by: Tony Hutter <hutter2@llnl.gov> --- MAINTAINERS | 5 + drivers/pci/hotplug/Kconfig | 12 + drivers/pci/hotplug/Makefile | 1 + drivers/pci/hotplug/pciehp_craye1k.c | 928 +++++++++++++++++++++++++++ 4 files changed, 946 insertions(+) create mode 100644 drivers/pci/hotplug/pciehp_craye1k.c