| Message ID | 20240910102326.927544-1-lukma@denx.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v5] dts: nxp: mxs: Add descriptions for imx287 based btt3-[012] devices | expand |
On Tue, 10 Sep 2024 12:23:26 +0200, Lukasz Majewski wrote: > The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to > some extend similar to already upstreamed XEA devices, hence are > using common imx28-lwe.dtsi file. > > New, imx28-btt3.dtsi file has been added to embrace common DTS > properties for different HW revisions for this device. > > As a result - changes introduced in imx28-btt3-[012].dts are > minimal. > > This patch also adds entry to fsl.yaml for btt3 board. > > Signed-off-by: Lukasz Majewski <lukma@denx.de> > > --- > Changes for v2: > - Rename dts file from btt3-[012] to imx28-btt3-[012] to match current > linux kernel naming convention > - Remove 'wlf,wm8974' from compatible for codec@1a > > Changes for v3: > - Keep alphabethical order for Makefile entries > > Changes for v4: > - Change compatible for btt3 board (to 'lwn,imx28-btt3') > > Changes for v5: > - Combine patch, which adds btt3-[012] with one adding board entry to > fsl.yaml > --- > .../devicetree/bindings/arm/fsl.yaml | 1 + > arch/arm/boot/dts/nxp/mxs/Makefile | 3 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts | 12 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts | 8 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts | 12 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi | 320 ++++++++++++++++++ > 6 files changed, 356 insertions(+) > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y nxp/mxs/imx28-btt3-0.dtb nxp/mxs/imx28-btt3-1.dtb nxp/mxs/imx28-btt3-2.dtb' for 20240910102326.927544-1-lukma@denx.de: arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: nand-controller@8000c000: #size-cells: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: nand-controller@8000c000: #size-cells: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/nand-controller.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80010000: $nodename:0: 'spi@80010000' does not match '^mmc(@.*)?$' from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: nand-controller@8000c000: #size-cells: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80010000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'non-removable', 'vmmc-supply' were unexpected) from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/interrupt-controller@80000000: failed to match any schema with compatible: ['fsl,imx28-icoll', 'fsl,icoll'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: nand-controller@8000c000: #size-cells: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/nand-controller.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80012000: $nodename:0: 'spi@80012000' does not match '^mmc(@.*)?$' from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80010000: $nodename:0: 'spi@80010000' does not match '^mmc(@.*)?$' from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80012000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'keep-power-in-suspend', 'mmc-pwrseq', 'no-1-8-v', 'non-removable', 'pm-ignore-notify', 'vmmc-supply', 'wlan@1' were unexpected) from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80010000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'non-removable', 'vmmc-supply' were unexpected) from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: nand-controller@8000c000: #size-cells: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80012000: $nodename:0: 'spi@80012000' does not match '^mmc(@.*)?$' from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80012000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'keep-power-in-suspend', 'mmc-pwrseq', 'no-1-8-v', 'non-removable', 'pm-ignore-notify', 'vmmc-supply', 'wlan@1' were unexpected) from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: nand-controller@8000c000: #size-cells: 0 was expected from schema $id: http://devicetree.org/schemas/mtd/nand-controller.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80014000: Unevaluated properties are not allowed ('clocks' was unexpected) from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80010000: $nodename:0: 'spi@80010000' does not match '^mmc(@.*)?$' from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80010000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'non-removable', 'vmmc-supply' were unexpected) from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: spi@80016000: Unevaluated properties are not allowed ('clocks' was unexpected) from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80014000: Unevaluated properties are not allowed ('clocks' was unexpected) from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80012000: $nodename:0: 'spi@80012000' does not match '^mmc(@.*)?$' from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80012000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bus-width', 'clocks', 'keep-power-in-suspend', 'mmc-pwrseq', 'no-1-8-v', 'non-removable', 'pm-ignore-notify', 'vmmc-supply', 'wlan@1' were unexpected) from schema $id: http://devicetree.org/schemas/mmc/mxs-mmc.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: spi@80016000: Unevaluated properties are not allowed ('clocks' was unexpected) from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80014000: Unevaluated properties are not allowed ('clocks' was unexpected) from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: spi@80016000: Unevaluated properties are not allowed ('clocks' was unexpected) from schema $id: http://devicetree.org/schemas/spi/mxs-spi.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: pinctrl@80018000: compatible: ['fsl,imx28-pinctrl', 'simple-bus'] is too long from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: pinctrl@80018000: 'auart0-2pins@0', 'auart0@0', 'auart1-2pins@0', 'auart1@0', 'auart2-2pins@0', 'auart2-2pins@1', 'auart2-pins@0', 'auart3-2pins@0', 'auart3-2pins@1', 'auart3@0', 'auart4@0', 'auart4@1', 'can0@0', 'can1@0', 'duart-4pins@0', 'duart@0', 'duart@1', 'gpmi-nand@0', 'gpmi-status-cfg@0', 'hog@0', 'hog@1', 'i2c0@0', 'i2c0@1', 'i2c1@0', 'i2c1@1', 'keypad-bttc@0', 'lcdif-16bit@0', 'lcdif-18bit@0', 'lcdif-24bit@0', 'lcdif-bttc@0', 'lcdif-bttc@1', 'lcdif-sync@0', 'mac0@0', 'mac0@1', 'mac1@0', 'mmc0-4bit@0', 'mmc0-8bit@0', 'mmc0-cd-cfg@0', 'mmc0-sck-cfg@0', 'mmc1-4bit@0', 'mmc1-cd-cfg@0', 'mmc1-sck-cfg@0', 'mmc2-4bit@0', 'mmc2-4bit@1', 'mmc2-cd-cfg@0', 'mmc2-sck-cfg@0', 'mmc2-sck-cfg@1', 'pwm0@0', 'pwm2@0', 'pwm3@0', 'pwm3@1', 'pwm4@0', 'saif0@0', 'saif0@1', 'saif1@0', 'spi2@0', 'spi3@0', 'spi3@1', 'ssp1-sdio@0', 'usb0@0', 'usb0@1', 'usb0id1@0', 'usb0id@0', 'usb1@0', 'usb1@1', 'wifi_en_pin@0' do not match any of the regexes: 'gpio@[0-9]+ $', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: pinctrl@80018000: compatible: ['fsl,imx28-pinctrl', 'simple-bus'] is too long from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: pinctrl@80018000: 'auart0-2pins@0', 'auart0@0', 'auart1-2pins@0', 'auart1@0', 'auart2-2pins@0', 'auart2-2pins@1', 'auart2-pins@0', 'auart3-2pins@0', 'auart3-2pins@1', 'auart3@0', 'auart4@0', 'auart4@1', 'can0@0', 'can1@0', 'duart-4pins@0', 'duart@0', 'duart@1', 'gpmi-nand@0', 'gpmi-status-cfg@0', 'hog@0', 'hog@1', 'i2c0@0', 'i2c0@1', 'i2c1@0', 'i2c1@1', 'keypad-bttc@0', 'lcdif-16bit@0', 'lcdif-18bit@0', 'lcdif-24bit@0', 'lcdif-bttc@0', 'lcdif-bttc@1', 'lcdif-sync@0', 'mac0@0', 'mac0@1', 'mac1@0', 'mmc0-4bit@0', 'mmc0-8bit@0', 'mmc0-cd-cfg@0', 'mmc0-sck-cfg@0', 'mmc1-4bit@0', 'mmc1-cd-cfg@0', 'mmc1-sck-cfg@0', 'mmc2-4bit@0', 'mmc2-4bit@1', 'mmc2-cd-cfg@0', 'mmc2-sck-cfg@0', 'mmc2-sck-cfg@1', 'pwm0@0', 'pwm2@0', 'pwm3@0', 'pwm3@1', 'pwm4@0', 'saif0@0', 'saif0@1', 'saif1@0', 'spi2@0', 'spi3@0', 'spi3@1', 'ssp1-sdio@0', 'usb0@0', 'usb0@1', 'usb0id1@0', 'usb0id@0', 'usb1@0', 'usb1@1', 'wifi_en_pin@0' do not match any of the regexes: 'gpio@[0-9]+ $', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: pinctrl@80018000: compatible: ['fsl,imx28-pinctrl', 'simple-bus'] is too long from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: pinctrl@80018000: 'auart0-2pins@0', 'auart0@0', 'auart1-2pins@0', 'auart1@0', 'auart2-2pins@0', 'auart2-2pins@1', 'auart2-pins@0', 'auart3-2pins@0', 'auart3-2pins@1', 'auart3@0', 'auart4@0', 'auart4@1', 'can0@0', 'can1@0', 'duart-4pins@0', 'duart@0', 'duart@1', 'gpmi-nand@0', 'gpmi-status-cfg@0', 'hog@0', 'hog@1', 'i2c0@0', 'i2c0@1', 'i2c1@0', 'i2c1@1', 'keypad-bttc@0', 'lcdif-16bit@0', 'lcdif-18bit@0', 'lcdif-24bit@0', 'lcdif-bttc@0', 'lcdif-bttc@1', 'lcdif-sync@0', 'mac0@0', 'mac0@1', 'mac1@0', 'mmc0-4bit@0', 'mmc0-8bit@0', 'mmc0-cd-cfg@0', 'mmc0-sck-cfg@0', 'mmc1-4bit@0', 'mmc1-cd-cfg@0', 'mmc1-sck-cfg@0', 'mmc2-4bit@0', 'mmc2-4bit@1', 'mmc2-cd-cfg@0', 'mmc2-sck-cfg@0', 'mmc2-sck-cfg@1', 'pwm0@0', 'pwm2@0', 'pwm3@0', 'pwm3@1', 'pwm4@0', 'saif0@0', 'saif0@1', 'saif1@0', 'spi2@0', 'spi3@0', 'spi3@1', 'ssp1-sdio@0', 'usb0@0', 'usb0@1', 'usb0id1@0', 'usb0id@0', 'usb1@0', 'usb1@1', 'wifi_en_pin@0' do not match any of the regexes: 'gpio@[0-9]+ $', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbh-bus@80000000/digctl@8001c000: failed to match any schema with compatible: ['fsl,imx28-digctl', 'fsl,imx23-digctl'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: lcdif@80030000: 'port' is a required property from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: lcdif@80030000: 'display', 'display0', 'display1', 'lcd-supply' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: lcdif@80030000: 'port' is a required property from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: lcdif@80030000: 'display', 'display0', 'display1', 'lcd-supply' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: lcdif@80030000: 'port' is a required property from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: lcdif@80030000: 'display', 'display0', 'display1', 'lcd-supply' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml# arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbx-bus@80040000/lradc@80050000: failed to match any schema with compatible: ['fsl,imx28-lradc'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbx-bus@80040000/lradc@80050000: failed to match any schema with compatible: ['fsl,imx28-lradc'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbx-bus@80040000/lradc@80050000: failed to match any schema with compatible: ['fsl,imx28-lradc'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot'] arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dtb: /apb@80000000/apbx-bus@80040000/timrot@80068000: failed to match any schema with compatible: ['fsl,imx28-timrot', 'fsl,timrot']
On Tue, Sep 10, 2024 at 5:23 AM Lukasz Majewski <lukma@denx.de> wrote: > > The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to > some extend similar to already upstreamed XEA devices, hence are > using common imx28-lwe.dtsi file. > > New, imx28-btt3.dtsi file has been added to embrace common DTS > properties for different HW revisions for this device. > > As a result - changes introduced in imx28-btt3-[012].dts are > minimal. > > This patch also adds entry to fsl.yaml for btt3 board. > > Signed-off-by: Lukasz Majewski <lukma@denx.de> > > --- > Changes for v2: > - Rename dts file from btt3-[012] to imx28-btt3-[012] to match current > linux kernel naming convention > - Remove 'wlf,wm8974' from compatible for codec@1a > > Changes for v3: > - Keep alphabethical order for Makefile entries > > Changes for v4: > - Change compatible for btt3 board (to 'lwn,imx28-btt3') > > Changes for v5: > - Combine patch, which adds btt3-[012] with one adding board entry to > fsl.yaml > --- > .../devicetree/bindings/arm/fsl.yaml | 1 + I said 1 series, not 1 patch. checkpatch.pl will also tell you bindings should be a separate patch. > arch/arm/boot/dts/nxp/mxs/Makefile | 3 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts | 12 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts | 8 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts | 12 + > arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi | 320 ++++++++++++++++++ > 6 files changed, 356 insertions(+) > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts > create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 80747d79418a..f290c824a91b 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -97,6 +97,7 @@ properties: - i2se,duckbill - i2se,duckbill-2 - karo,tx28 # Ka-Ro electronics TX28 module + - lwn,imx28-btt3 - lwn,imx28-xea - msr,m28cu3 # M28 SoM with custom base board - schulercontrol,imx28-sps1 diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile b/arch/arm/boot/dts/nxp/mxs/Makefile index a430d04f9c69..96dd31ea19ba 100644 --- a/arch/arm/boot/dts/nxp/mxs/Makefile +++ b/arch/arm/boot/dts/nxp/mxs/Makefile @@ -8,6 +8,9 @@ dtb-$(CONFIG_ARCH_MXS) += \ imx28-apf28.dtb \ imx28-apf28dev.dtb \ imx28-apx4devkit.dtb \ + imx28-btt3-0.dtb \ + imx28-btt3-1.dtb \ + imx28-btt3-2.dtb \ imx28-cfa10036.dtb \ imx28-cfa10037.dtb \ imx28-cfa10049.dtb \ diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts new file mode 100644 index 000000000000..6ac46e4b21bb --- /dev/null +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2024 + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + */ + +/dts-v1/; +#include "imx28-btt3.dtsi" + +&hog_pins_rev { + fsl,pull-up = <MXS_PULL_ENABLE>; +}; diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts new file mode 100644 index 000000000000..213fe931c58b --- /dev/null +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2024 + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + */ + +/dts-v1/; +#include "imx28-btt3.dtsi" diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts new file mode 100644 index 000000000000..c787c2d03463 --- /dev/null +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2024 + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + */ + +/dts-v1/; +#include "imx28-btt3.dtsi" + +&lcdif { + display = <&display_te_b>; +}; diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi new file mode 100644 index 000000000000..94a21ea8d5d2 --- /dev/null +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi @@ -0,0 +1,320 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2024 + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de + */ +/dts-v1/; +#include "imx28-lwe.dtsi" + +/ { + model = "BTT3"; + + compatible = "lwn,imx28-btt3", "fsl,imx28"; + + chosen { + bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1 quiet"; + }; + + memory@40000000 { + reg = <0x40000000 0x10000000>; + device_type = "memory"; + }; + + poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 24 0>; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "BTTC Audio"; + simple-audio-card,widgets = "Speaker", "BTTC Speaker"; + simple-audio-card,routing = "BTTC Speaker", "SPKOUTN", "BTTC Speaker", "SPKOUTP"; + simple-audio-card,dai-link@0 { + format = "left_j"; + bitclock-master = <&dai0_master>; + frame-master = <&dai0_master>; + mclk-fs = <256>; + dai0_master: cpu { + sound-dai = <&saif0>; + }; + codec { + sound-dai = <&wm89xx>; + clocks = <&saif0>; + }; + }; + }; + + wifi_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_en_pin_bttc>; + reset-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + /* W1-163 needs 60us for WL_EN to be low and */ + /* 150ms after high before downloading FW is possible */ + post-power-on-delay-ms = <200>; + power-off-delay-us = <100>; + }; +}; + +&auart0 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + status = "okay"; +}; + +&auart3 { + pinctrl-names = "default"; + pinctrl-0 = <&auart3_pins_a>; + uart-has-rtscts; + status = "okay"; +}; + +&i2c0 { + wm89xx: codec@1a { + compatible = "wlf,wm8940"; + reg = <0x1a>; + #sound-dai-cells = <0>; + }; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a>, <&lcdif_sync_pins_bttc>, + <&lcdif_reset_pins_bttc>; + lcd-supply = <®_3v3>; + display = <&display0>; + status = "okay"; + display0: display0 { + bits-per-pixel = <32>; + bus-width = <24>; + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <6500000>; + hactive = <320>; + vactive = <240>; + hfront-porch = <20>; + hback-porch = <38>; + hsync-len = <30>; + vfront-porch = <4>; + vback-porch = <14>; + vsync-len = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <0>; + pixelclk-active = <1>; + }; + }; + }; + display_te_b: display1 { + bits-per-pixel = <32>; + bus-width = <24>; + display-timings { + native-mode = <&timing0>; + timing_te_b: timing0 { + clock-frequency = <6500000>; + hactive = <320>; + vactive = <240>; + hfront-porch = <20>; + hback-porch = <68>; + hsync-len = <30>; + vfront-porch = <4>; + vback-porch = <14>; + vsync-len = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; + +}; + +&mac0 { + clocks = <&clks 57>, <&clks 57>, <&clks 64>; + clock-names = "ipg", "ahb", "enet_out"; + phy-handle = <&mac0_phy>; + phy-mode = "rmii"; + phy-supply = <®_3v3>; + local-mac-address = [ 00 11 B8 00 BF 8A ]; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + mac0_phy: ethernet-phy@0 { + /* LAN8720Ai - PHY ID */ + compatible = "ethernet-phy-id0007.c0f0","ethernet-phy-ieee802.3-c22"; + reg = <0>; + smsc,disable-energy-detect; + max-speed = <100>; + + reset-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; /* GPIO4_12 */ + reset-assert-us = <1000>; + reset-deassert-us = <1000>; + }; + }; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>, <&hog_pins_rev>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_RDY2__GPIO_0_22 + MX28_PAD_GPMI_RDY3__GPIO_0_23 + MX28_PAD_GPMI_RDN__GPIO_0_24 + MX28_PAD_LCD_VSYNC__GPIO_1_28 + MX28_PAD_SSP2_SS1__GPIO_2_20 + MX28_PAD_SSP2_SS2__GPIO_2_21 + MX28_PAD_AUART2_CTS__GPIO_3_10 + MX28_PAD_AUART2_RTS__GPIO_3_11 + MX28_PAD_GPMI_WRN__GPIO_0_25 + MX28_PAD_ENET0_RXD2__GPIO_4_9 + MX28_PAD_ENET0_TXD2__GPIO_4_11 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + hog_pins_rev: hog@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_RXD3__GPIO_4_10 + MX28_PAD_ENET0_TX_CLK__GPIO_4_5 + MX28_PAD_ENET0_COL__GPIO_4_14 + MX28_PAD_ENET0_CRS__GPIO_4_15 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + keypad_pins_bttc: keypad-bttc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_D00__GPIO_0_0 + MX28_PAD_AUART0_CTS__GPIO_3_2 + MX28_PAD_AUART0_RTS__GPIO_3_3 + MX28_PAD_GPMI_D03__GPIO_0_3 + MX28_PAD_GPMI_D04__GPIO_0_4 + MX28_PAD_GPMI_D05__GPIO_0_5 + MX28_PAD_GPMI_D06__GPIO_0_6 + MX28_PAD_GPMI_D07__GPIO_0_7 + MX28_PAD_GPMI_CE1N__GPIO_0_17 + MX28_PAD_GPMI_CE2N__GPIO_0_18 + MX28_PAD_GPMI_CE3N__GPIO_0_19 + MX28_PAD_GPMI_RDY0__GPIO_0_20 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_sync_pins_bttc: lcdif-bttc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_DOTCLK__LCD_DOTCLK + MX28_PAD_LCD_ENABLE__LCD_ENABLE + MX28_PAD_LCD_HSYNC__LCD_HSYNC + MX28_PAD_LCD_RD_E__LCD_VSYNC + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_reset_pins_bttc: lcdif-bttc@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_LCD_RESET__GPIO_3_30 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + ssp1_sdio_pins_a: ssp1-sdio@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP1_DATA0__SSP1_D0 + MX28_PAD_GPMI_D01__SSP1_D1 + MX28_PAD_GPMI_D02__SSP1_D2 + MX28_PAD_SSP1_DATA3__SSP1_D3 + MX28_PAD_SSP1_CMD__SSP1_CMD + MX28_PAD_SSP1_SCK__SSP1_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + wifi_en_pin_bttc: wifi_en_pin@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_CLE__GPIO_0_27 + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pins_a>; + status = "okay"; +}; + +®_usb_5v { + gpio = <&gpio1 28 0>; +}; + +&saif0 { + pinctrl-names = "default"; + pinctrl-0 = <&saif0_pins_a>; + #sound-dai-cells = <0>; + assigned-clocks = <&clks 53>; + assigned-clock-rates = <12000000>; + status = "okay"; +}; + +&saif1 { + pinctrl-names = "default"; + pinctrl-0 = <&saif1_pins_a>; + fsl,saif-master = <&saif0>; + #sound-dai-cells = <0>; + status = "okay"; +}; + +&ssp1 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&ssp1_sdio_pins_a>; + bus-width = <4>; + no-1-8-v; /* force 3.3V VIO */ + pm-ignore-notify; + non-removable; + vmmc-supply = <®_3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + keep-power-in-suspend; + status = "okay"; + + wlan@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +&ssp2 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; +};
The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to some extend similar to already upstreamed XEA devices, hence are using common imx28-lwe.dtsi file. New, imx28-btt3.dtsi file has been added to embrace common DTS properties for different HW revisions for this device. As a result - changes introduced in imx28-btt3-[012].dts are minimal. This patch also adds entry to fsl.yaml for btt3 board. Signed-off-by: Lukasz Majewski <lukma@denx.de> --- Changes for v2: - Rename dts file from btt3-[012] to imx28-btt3-[012] to match current linux kernel naming convention - Remove 'wlf,wm8974' from compatible for codec@1a Changes for v3: - Keep alphabethical order for Makefile entries Changes for v4: - Change compatible for btt3 board (to 'lwn,imx28-btt3') Changes for v5: - Combine patch, which adds btt3-[012] with one adding board entry to fsl.yaml --- .../devicetree/bindings/arm/fsl.yaml | 1 + arch/arm/boot/dts/nxp/mxs/Makefile | 3 + arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts | 12 + arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts | 8 + arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts | 12 + arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi | 320 ++++++++++++++++++ 6 files changed, 356 insertions(+) create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi