| Message ID | 20241004-x1e80100-ps8830-v2-0-5cd8008c8c40@linaro.org (mailing list archive) |
|---|---|
| Headers | show |
| Series | usb: typec: Add new driver for Parade PS8830 Type-C Retimer | expand |
On Fri, Oct 04, 2024 at 04:57:36PM +0300, Abel Vesa wrote: > The Parade PS8830 is a Type-C multi-protocol retimer that is controlled > via I2C. It provides altmode and orientation handling and usually sits > between the Type-C port and the PHY. > > It is currently used alongside Qualcomm Snapdragon X Elite SoCs on quite > a few laptops already. > > This new driver adds support for the following 3 modes: > - DP 4lanes (pin assignments C and E) > - DP 2lanes + USB3 (pin assignment D) > - USB3 > > This retimer is a LTTPR (Link-Training Tunable PHY Repeater) which means > it can support link training from source to itself. This means that the > DP driver needs to be aware of the repeater presence and to handle > the link training accordingly. This is currently missing from msm dp > driver, but there is already effort going on to add it. Once done, > full external DP will be working on all X1E laptops that make use of > this retimer. I was gonna ask you to include the devicetree changes that enables the retimers as part of this series (to facilitate review and testing), but perhaps you should indeed not post them again until LTTPR support is in place. > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > --- > Changes in v2: > - Addressed all comments from Johan and Konrad. > - Reworked the handling of the vregs so it would be more cleaner. > Dropped the usage of bulk regulators API and handled them separately. > Also discribed all regulators according to data sheet. > - Added all delays according to data sheet. > - Fixed coldplug (on boot) orientation detection. Coldplug orientation detection still does not work here with this series applied. I'm not entirely sure this whether worked better with v1, but with v2 my SuperSpeed ethernet device shows up as a HighSpeed device in one orientation. It is also not disconnected an re-enumerated as SS as is the case on the X13s (and possibly with v1): usb 1-1: new high-speed USB device number 2 using xhci-hcd > - Didn't pick Krzysztof's R-b tag because the bindings changed w.r.t > supplies. > - Link to v1: https://lore.kernel.org/r/20240829-x1e80100-ps8830-v1-0-bcc4790b1d45@linaro.org > > --- > Abel Vesa (2): > dt-bindings: usb: Add Parade PS8830 Type-C retimer bindings > usb: typec: Add support for Parade PS8830 Type-C Retimer Johan
On 24-10-15 14:41:25, Johan Hovold wrote: > On Fri, Oct 04, 2024 at 04:57:36PM +0300, Abel Vesa wrote: > > The Parade PS8830 is a Type-C multi-protocol retimer that is controlled > > via I2C. It provides altmode and orientation handling and usually sits > > between the Type-C port and the PHY. > > > > It is currently used alongside Qualcomm Snapdragon X Elite SoCs on quite > > a few laptops already. > > > > This new driver adds support for the following 3 modes: > > - DP 4lanes (pin assignments C and E) > > - DP 2lanes + USB3 (pin assignment D) > > - USB3 > > > > This retimer is a LTTPR (Link-Training Tunable PHY Repeater) which means > > it can support link training from source to itself. This means that the > > DP driver needs to be aware of the repeater presence and to handle > > the link training accordingly. This is currently missing from msm dp > > driver, but there is already effort going on to add it. Once done, > > full external DP will be working on all X1E laptops that make use of > > this retimer. > > I was gonna ask you to include the devicetree changes that enables the > retimers as part of this series (to facilitate review and testing), but > perhaps you should indeed not post them again until LTTPR support is in > place. I was thinking maybe we should not wait for LTTPR support as this series brings orientation support as is. I still need to figure out how to strip out the DP parts of it in such a way that orientation should still be working but DP should not (until LTTPR is in). > > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > > --- > > Changes in v2: > > - Addressed all comments from Johan and Konrad. > > - Reworked the handling of the vregs so it would be more cleaner. > > Dropped the usage of bulk regulators API and handled them separately. > > Also discribed all regulators according to data sheet. > > - Added all delays according to data sheet. > > - Fixed coldplug (on boot) orientation detection. > > Coldplug orientation detection still does not work here with this series > applied. > > I'm not entirely sure this whether worked better with v1, but with v2 > my SuperSpeed ethernet device shows up as a HighSpeed device in one > orientation. It is also not disconnected an re-enumerated as SS as is > the case on the X13s (and possibly with v1): > > usb 1-1: new high-speed USB device number 2 using xhci-hcd For coldplug, this series does the right thing as it leaves the retimer initialized if it was left enabled at boot. There is a second part needed for the coldplug to work. That is the regulator-boot-on property in retimer's vregs nodes. That will ensure that the regulator is not disabled until retimer driver probes and will keep the retimer initialized until USB device is enumerated. > > > - Didn't pick Krzysztof's R-b tag because the bindings changed w.r.t > > supplies. > > - Link to v1: https://lore.kernel.org/r/20240829-x1e80100-ps8830-v1-0-bcc4790b1d45@linaro.org > > > > --- > > Abel Vesa (2): > > dt-bindings: usb: Add Parade PS8830 Type-C retimer bindings > > usb: typec: Add support for Parade PS8830 Type-C Retimer > > Johan
On 10/15/24 15:03, Abel Vesa wrote: > On 24-10-15 14:41:25, Johan Hovold wrote: >> On Fri, Oct 04, 2024 at 04:57:36PM +0300, Abel Vesa wrote: >>> The Parade PS8830 is a Type-C multi-protocol retimer that is controlled >>> via I2C. It provides altmode and orientation handling and usually sits >>> between the Type-C port and the PHY. >>> >>> It is currently used alongside Qualcomm Snapdragon X Elite SoCs on quite >>> a few laptops already. >>> >>> This new driver adds support for the following 3 modes: >>> - DP 4lanes (pin assignments C and E) >>> - DP 2lanes + USB3 (pin assignment D) >>> - USB3 >>> >>> This retimer is a LTTPR (Link-Training Tunable PHY Repeater) which means >>> it can support link training from source to itself. This means that the >>> DP driver needs to be aware of the repeater presence and to handle >>> the link training accordingly. This is currently missing from msm dp >>> driver, but there is already effort going on to add it. Once done, >>> full external DP will be working on all X1E laptops that make use of >>> this retimer. >> >> I was gonna ask you to include the devicetree changes that enables the >> retimers as part of this series (to facilitate review and testing), but >> perhaps you should indeed not post them again until LTTPR support is in >> place. > > I was thinking maybe we should not wait for LTTPR support as this series > brings orientation support as is. It also happens to bring an undesired crash-on-unplug feature when DP is enabled.. I suppose it's fine to bring this series in if you separate enabling the retimer on devices from wiring DP up. Konrad
On Tue, Oct 15, 2024 at 04:03:53PM +0300, Abel Vesa wrote: > On 24-10-15 14:41:25, Johan Hovold wrote: > > On Fri, Oct 04, 2024 at 04:57:36PM +0300, Abel Vesa wrote: > > > The Parade PS8830 is a Type-C multi-protocol retimer that is controlled > > > via I2C. It provides altmode and orientation handling and usually sits > > > between the Type-C port and the PHY. > > > This retimer is a LTTPR (Link-Training Tunable PHY Repeater) which means > > > it can support link training from source to itself. This means that the > > > DP driver needs to be aware of the repeater presence and to handle > > > the link training accordingly. This is currently missing from msm dp > > > driver, but there is already effort going on to add it. Once done, > > > full external DP will be working on all X1E laptops that make use of > > > this retimer. > > > > I was gonna ask you to include the devicetree changes that enables the > > retimers as part of this series (to facilitate review and testing), but > > perhaps you should indeed not post them again until LTTPR support is in > > place. > > I was thinking maybe we should not wait for LTTPR support as this series > brings orientation support as is. I still need to figure out how to > strip out the DP parts of it in such a way that orientation should still > be working but DP should not (until LTTPR is in). Yeah, possible, or you can at least include the DT patches here but mark them as do-not-merge-yet or similar. > > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > > > --- > > > Changes in v2: > > > - Fixed coldplug (on boot) orientation detection. > > > > Coldplug orientation detection still does not work here with this series > > applied. > > > > I'm not entirely sure this whether worked better with v1, but with v2 > > my SuperSpeed ethernet device shows up as a HighSpeed device in one > > orientation. It is also not disconnected an re-enumerated as SS as is > > the case on the X13s (and possibly with v1): > > > > usb 1-1: new high-speed USB device number 2 using xhci-hcd > > For coldplug, this series does the right thing as it leaves the retimer > initialized if it was left enabled at boot. There is a second part > needed for the coldplug to work. That is the regulator-boot-on property > in retimer's vregs nodes. That will ensure that the regulator is not > disabled until retimer driver probes and will keep the retimer initialized > until USB device is enumerated. I can confirm that marking the regulators as having been left on by the bootloader so that they are not disabled temporarily during boot indeed fixes the coldplug issue here. That however makes me wonder whether something is missing in the driver so that it still relies on setup having been done by the boot firmware. Have you tried actually asserting reset during probe to verify that driver can configure the retimers itself without relying on the boot firmware? Johan
On 24-10-17 08:00:44, Johan Hovold wrote: > On Tue, Oct 15, 2024 at 04:03:53PM +0300, Abel Vesa wrote: > > On 24-10-15 14:41:25, Johan Hovold wrote: > > > On Fri, Oct 04, 2024 at 04:57:36PM +0300, Abel Vesa wrote: > > > > The Parade PS8830 is a Type-C multi-protocol retimer that is controlled > > > > via I2C. It provides altmode and orientation handling and usually sits > > > > between the Type-C port and the PHY. > > > > > This retimer is a LTTPR (Link-Training Tunable PHY Repeater) which means > > > > it can support link training from source to itself. This means that the > > > > DP driver needs to be aware of the repeater presence and to handle > > > > the link training accordingly. This is currently missing from msm dp > > > > driver, but there is already effort going on to add it. Once done, > > > > full external DP will be working on all X1E laptops that make use of > > > > this retimer. > > > > > > I was gonna ask you to include the devicetree changes that enables the > > > retimers as part of this series (to facilitate review and testing), but > > > perhaps you should indeed not post them again until LTTPR support is in > > > place. > > > > I was thinking maybe we should not wait for LTTPR support as this series > > brings orientation support as is. I still need to figure out how to > > strip out the DP parts of it in such a way that orientation should still > > be working but DP should not (until LTTPR is in). > > Yeah, possible, or you can at least include the DT patches here but mark > them as do-not-merge-yet or similar. Sure, will do that. Will have to split the DP part of it into separate patches and mark only those as do-not-merge-yet. > > > > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > > > > --- > > > > Changes in v2: > > > > > - Fixed coldplug (on boot) orientation detection. > > > > > > Coldplug orientation detection still does not work here with this series > > > applied. > > > > > > I'm not entirely sure this whether worked better with v1, but with v2 > > > my SuperSpeed ethernet device shows up as a HighSpeed device in one > > > orientation. It is also not disconnected an re-enumerated as SS as is > > > the case on the X13s (and possibly with v1): > > > > > > usb 1-1: new high-speed USB device number 2 using xhci-hcd > > > > For coldplug, this series does the right thing as it leaves the retimer > > initialized if it was left enabled at boot. There is a second part > > needed for the coldplug to work. That is the regulator-boot-on property > > in retimer's vregs nodes. That will ensure that the regulator is not > > disabled until retimer driver probes and will keep the retimer initialized > > until USB device is enumerated. > > I can confirm that marking the regulators as having been left on by the > bootloader so that they are not disabled temporarily during boot indeed > fixes the coldplug issue here. > > That however makes me wonder whether something is missing in the driver > so that it still relies on setup having been done by the boot firmware. > > Have you tried actually asserting reset during probe to verify that > driver can configure the retimers itself without relying on the boot > firmware? We do not want to reset the retimers on probe because we won't be able to figure out the orientation config until next pmic glink notify comes. The pmic glink notify only triggers on USB event, which never comes until you replug the device. So in order to have coldplug orientation configured correctly in the retimer, we need to make sure the retimer holds state until unplug. > > Johan
On Thu, Oct 17, 2024 at 11:25:20AM +0300, Abel Vesa wrote: > On 24-10-17 08:00:44, Johan Hovold wrote: > > I can confirm that marking the regulators as having been left on by the > > bootloader so that they are not disabled temporarily during boot indeed > > fixes the coldplug issue here. > > > > That however makes me wonder whether something is missing in the driver > > so that it still relies on setup having been done by the boot firmware. > > > > Have you tried actually asserting reset during probe to verify that > > driver can configure the retimers itself without relying on the boot > > firmware? > > We do not want to reset the retimers on probe because we won't be able > to figure out the orientation config until next pmic glink notify comes. > The pmic glink notify only triggers on USB event, which never comes > until you replug the device. So in order to have coldplug orientation > configured correctly in the retimer, we need to make sure the retimer > holds state until unplug. Ok, thanks for clarifying. As we've discussed off-list it should be possible to retrieve the orientation from the orientation gpios, but I'm sure there are bits missing in the kernel for propagating that information to the retimers currently. If I understood you correctly you did reset and reinitialise the retimers in v1, which is useful during development at least to make sure that the driver is complete. Johan
The Parade PS8830 is a Type-C multi-protocol retimer that is controlled via I2C. It provides altmode and orientation handling and usually sits between the Type-C port and the PHY. It is currently used alongside Qualcomm Snapdragon X Elite SoCs on quite a few laptops already. This new driver adds support for the following 3 modes: - DP 4lanes (pin assignments C and E) - DP 2lanes + USB3 (pin assignment D) - USB3 This retimer is a LTTPR (Link-Training Tunable PHY Repeater) which means it can support link training from source to itself. This means that the DP driver needs to be aware of the repeater presence and to handle the link training accordingly. This is currently missing from msm dp driver, but there is already effort going on to add it. Once done, full external DP will be working on all X1E laptops that make use of this retimer. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- Changes in v2: - Addressed all comments from Johan and Konrad. - Reworked the handling of the vregs so it would be more cleaner. Dropped the usage of bulk regulators API and handled them separately. Also discribed all regulators according to data sheet. - Added all delays according to data sheet. - Fixed coldplug (on boot) orientation detection. - Didn't pick Krzysztof's R-b tag because the bindings changed w.r.t supplies. - Link to v1: https://lore.kernel.org/r/20240829-x1e80100-ps8830-v1-0-bcc4790b1d45@linaro.org --- Abel Vesa (2): dt-bindings: usb: Add Parade PS8830 Type-C retimer bindings usb: typec: Add support for Parade PS8830 Type-C Retimer .../devicetree/bindings/usb/parade,ps8830.yaml | 129 +++++++ drivers/usb/typec/mux/Kconfig | 10 + drivers/usb/typec/mux/Makefile | 1 + drivers/usb/typec/mux/ps8830.c | 424 +++++++++++++++++++++ 4 files changed, 564 insertions(+) --- base-commit: c02d24a5af66a9806922391493205a344749f2c4 change-id: 20240521-x1e80100-ps8830-d5ccca95b557 Best regards,