| Message ID | 20241021103617.653386-5-inochiama@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | riscv: sophgo: Add ethernet support for SG2044 | expand |
> +static void sophgo_dwmac_fix_mac_speed(void *priv, unsigned int speed, unsigned int mode) > +{ > + struct sophgo_dwmac *dwmac = priv; > + unsigned long rate; > + int ret; > + > + switch (speed) { > + case SPEED_1000: > + rate = 125000000; > + break; > + case SPEED_100: > + rate = 25000000; > + break; > + case SPEED_10: > + rate = 2500000; > + break; > + default: > + dev_err(dwmac->dev, "invalid speed %u\n", speed); > + break; > + } There was a helper added recently for this, since it appears repeatedly in drivers. > + ret = regmap_set_bits(regmap, args[0], DWMAC_SG2044_FLAG_USE_RX_DELAY); > + if (ret) > + return dev_err_probe(&pdev->dev, ret, > + "failed to set the phy rx delay\n"); Please could you explain what this delay is for. Is it the 2ns RGMII delay? Andrew
On Mon, Oct 21, 2024 at 02:22:47PM +0200, Andrew Lunn wrote: > > +static void sophgo_dwmac_fix_mac_speed(void *priv, unsigned int speed, unsigned int mode) > > +{ > > + struct sophgo_dwmac *dwmac = priv; > > + unsigned long rate; > > + int ret; > > + > > + switch (speed) { > > + case SPEED_1000: > > + rate = 125000000; > > + break; > > + case SPEED_100: > > + rate = 25000000; > > + break; > > + case SPEED_10: > > + rate = 2500000; > > + break; > > + default: > > + dev_err(dwmac->dev, "invalid speed %u\n", speed); > > + break; > > + } > > There was a helper added recently for this, since it appears > repeatedly in drivers. > OK, I will change it. > > + ret = regmap_set_bits(regmap, args[0], DWMAC_SG2044_FLAG_USE_RX_DELAY); > > + if (ret) > > + return dev_err_probe(&pdev->dev, ret, > > + "failed to set the phy rx delay\n"); > > Please could you explain what this delay is for. Is it the 2ns RGMII > delay? > > Andrew It is related to the RGMII delay. On sg2044, when the phy sets rx-delay, the interal mac is not set the same delay, so this is needed to be set. Regards, Inochi
> It is related to the RGMII delay. On sg2044, when the phy > sets rx-delay, the interal mac is not set the same delay, > so this is needed to be set. This is the wrong way to do it. Please look at how phy-mode should be used, the four different "rgmii" values. Nearly everybody gets this wrong, so there are plenty of emails from me in the netdev list about how it should be done. Andrew --- pw-bot: cr
On 2024/10/21 18:36, Inochi Amaoto wrote: [......] > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c > new file mode 100644 > index 000000000000..83c67c061182 > --- /dev/null > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c > @@ -0,0 +1,132 @@ [......] > +module_platform_driver(sophgo_dwmac_driver); > + > +MODULE_LICENSE("GPL"); > +MODULE_DESCRIPTION("Sophgo DWMAC platform driver"); Missing MODULE_AUTHOR ......
On Mon, Oct 21, 2024 at 03:27:18PM +0200, Andrew Lunn wrote: > > It is related to the RGMII delay. On sg2044, when the phy > > sets rx-delay, the interal mac is not set the same delay, > > so this is needed to be set. > > This is the wrong way to do it. Please look at how phy-mode should be > used, the four different "rgmii" values. Nearly everybody gets this > wrong, so there are plenty of emails from me in the netdev list about > how it should be done. > The phy-mode is alreay set to the "rgmii-id" and a rx delay is already set (a default tx delay is set by the phy driver). In the scenario the extra bit is used to fix 2ns difference between the sampling clock and data. It is more like an extra setting and the kernel can not handle it by only setting the phy-mode. This is draft dts patch for the sg2044 gmac. https://github.com/project-inochi/linux/commit/381cb6000044a89cb13d6d9c839e9bbc7b9d2e5a Regards, Inochi
Hi Inochi, kernel test robot noticed the following build warnings: [auto build test WARNING on robh/for-next] [also build test WARNING on sophgo/for-next sophgo/fixes net-next/main net/main linus/master v6.12-rc4 next-20241021] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Inochi-Amaoto/dt-bindings-net-snps-dwmac-Add-dwmac-5-30a-version/20241021-184301 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next patch link: https://lore.kernel.org/r/20241021103617.653386-5-inochiama%40gmail.com patch subject: [PATCH 4/4] net: stmmac: Add glue layer for Sophgo SG2044 SoC config: x86_64-allyesconfig (https://download.01.org/0day-ci/archive/20241022/202410221853.0nt4WyvW-lkp@intel.com/config) compiler: clang version 18.1.8 (https://github.com/llvm/llvm-project 3b5b5c1ec4a3095ab096dd780e84d7ab81f3d7ff) reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20241022/202410221853.0nt4WyvW-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202410221853.0nt4WyvW-lkp@intel.com/ All warnings (new ones prefixed by >>): >> drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c:41:2: warning: variable 'rate' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized] 41 | default: | ^~~~~~~ drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c:46:36: note: uninitialized use occurs here 46 | ret = clk_set_rate(dwmac->clk_tx, rate); | ^~~~ drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c:28:20: note: initialize the variable 'rate' to silence this warning 28 | unsigned long rate; | ^ | = 0 1 warning generated. Kconfig warnings: (for reference only) WARNING: unmet direct dependencies detected for MODVERSIONS Depends on [n]: MODULES [=y] && !COMPILE_TEST [=y] Selected by [y]: - RANDSTRUCT_FULL [=y] && (CC_HAS_RANDSTRUCT [=y] || GCC_PLUGINS [=n]) && MODULES [=y] vim +/rate +41 drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c 24 25 static void sophgo_dwmac_fix_mac_speed(void *priv, unsigned int speed, unsigned int mode) 26 { 27 struct sophgo_dwmac *dwmac = priv; 28 unsigned long rate; 29 int ret; 30 31 switch (speed) { 32 case SPEED_1000: 33 rate = 125000000; 34 break; 35 case SPEED_100: 36 rate = 25000000; 37 break; 38 case SPEED_10: 39 rate = 2500000; 40 break; > 41 default: 42 dev_err(dwmac->dev, "invalid speed %u\n", speed); 43 break; 44 } 45 46 ret = clk_set_rate(dwmac->clk_tx, rate); 47 if (ret) 48 dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate); 49 } 50
On Tue, Oct 22, 2024 at 06:21:49PM +0800, Inochi Amaoto wrote: > On Mon, Oct 21, 2024 at 03:27:18PM +0200, Andrew Lunn wrote: > > > It is related to the RGMII delay. On sg2044, when the phy > > > sets rx-delay, the interal mac is not set the same delay, > > > so this is needed to be set. > > > > This is the wrong way to do it. Please look at how phy-mode should be > > used, the four different "rgmii" values. Nearly everybody gets this > > wrong, so there are plenty of emails from me in the netdev list about > > how it should be done. > > > > The phy-mode is alreay set to the "rgmii-id" and a rx delay is already > set (a default tx delay is set by the phy driver). In the scenario > the extra bit is used to fix 2ns difference between the sampling clock > and data. It is more like an extra setting and the kernel can not handle > it by only setting the phy-mode. This sounds wrong. So in DT you have rgmii-id? You say the PHY is doing TX delay. So you pass PHY_INTERFACE_MODE_RGMII_TXID to the PHY? It is not clear from this patch, i don't see any code mentioning PHY_INTERFACE_MODE_RGMII_TXID. Could you point me at that code. Andrew
On Tue, Oct 22, 2024 at 03:51:08PM +0200, Andrew Lunn wrote: > On Tue, Oct 22, 2024 at 06:21:49PM +0800, Inochi Amaoto wrote: > > On Mon, Oct 21, 2024 at 03:27:18PM +0200, Andrew Lunn wrote: > > > > It is related to the RGMII delay. On sg2044, when the phy > > > > sets rx-delay, the interal mac is not set the same delay, > > > > so this is needed to be set. > > > > > > This is the wrong way to do it. Please look at how phy-mode should be > > > used, the four different "rgmii" values. Nearly everybody gets this > > > wrong, so there are plenty of emails from me in the netdev list about > > > how it should be done. > > > > > > > The phy-mode is alreay set to the "rgmii-id" and a rx delay is already > > set (a default tx delay is set by the phy driver). In the scenario > > the extra bit is used to fix 2ns difference between the sampling clock > > and data. It is more like an extra setting and the kernel can not handle > > it by only setting the phy-mode. > > This sounds wrong. > > So in DT you have rgmii-id? You say the PHY is doing TX delay. So you > pass PHY_INTERFACE_MODE_RGMII_TXID to the PHY? It is not clear from > this patch, i don't see any code mentioning > PHY_INTERFACE_MODE_RGMII_TXID. Could you point me at that code. > > Andrew The phy on the board I have is YT8531, The config code is here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/motorcomm.c#n868 As the syscon only has a config on rx delay. I have already fix the code and only set the bit when the mac is rgmii-rxid/id. Regards, Inochi.
On Wed, Oct 23, 2024 at 08:41:36AM +0800, Inochi Amaoto wrote: > On Tue, Oct 22, 2024 at 03:51:08PM +0200, Andrew Lunn wrote: > > On Tue, Oct 22, 2024 at 06:21:49PM +0800, Inochi Amaoto wrote: > > > On Mon, Oct 21, 2024 at 03:27:18PM +0200, Andrew Lunn wrote: > > > > > It is related to the RGMII delay. On sg2044, when the phy > > > > > sets rx-delay, the interal mac is not set the same delay, > > > > > so this is needed to be set. > > > > > > > > This is the wrong way to do it. Please look at how phy-mode should be > > > > used, the four different "rgmii" values. Nearly everybody gets this > > > > wrong, so there are plenty of emails from me in the netdev list about > > > > how it should be done. > > > > > > > > > > The phy-mode is alreay set to the "rgmii-id" and a rx delay is already > > > set (a default tx delay is set by the phy driver). In the scenario > > > the extra bit is used to fix 2ns difference between the sampling clock > > > and data. It is more like an extra setting and the kernel can not handle > > > it by only setting the phy-mode. > > > > This sounds wrong. > > > > So in DT you have rgmii-id? You say the PHY is doing TX delay. So you > > pass PHY_INTERFACE_MODE_RGMII_TXID to the PHY? It is not clear from > > this patch, i don't see any code mentioning > > PHY_INTERFACE_MODE_RGMII_TXID. Could you point me at that code. > > > > Andrew > > The phy on the board I have is YT8531, The config code is here: > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/motorcomm.c#n868 This PHY should be able to do rgmii-id, so there is no need for the MAC to add delays. We encourage that setup in linux, so all RGMII MAC/PHY pairs are the same, the PHY add the delays. Andrew
On Wed, Oct 23, 2024 at 03:08:52AM +0200, Andrew Lunn wrote: > On Wed, Oct 23, 2024 at 08:41:36AM +0800, Inochi Amaoto wrote: > > On Tue, Oct 22, 2024 at 03:51:08PM +0200, Andrew Lunn wrote: > > > On Tue, Oct 22, 2024 at 06:21:49PM +0800, Inochi Amaoto wrote: > > > > On Mon, Oct 21, 2024 at 03:27:18PM +0200, Andrew Lunn wrote: > > > > > > It is related to the RGMII delay. On sg2044, when the phy > > > > > > sets rx-delay, the interal mac is not set the same delay, > > > > > > so this is needed to be set. > > > > > > > > > > This is the wrong way to do it. Please look at how phy-mode should be > > > > > used, the four different "rgmii" values. Nearly everybody gets this > > > > > wrong, so there are plenty of emails from me in the netdev list about > > > > > how it should be done. > > > > > > > > > > > > > The phy-mode is alreay set to the "rgmii-id" and a rx delay is already > > > > set (a default tx delay is set by the phy driver). In the scenario > > > > the extra bit is used to fix 2ns difference between the sampling clock > > > > and data. It is more like an extra setting and the kernel can not handle > > > > it by only setting the phy-mode. > > > > > > This sounds wrong. > > > > > > So in DT you have rgmii-id? You say the PHY is doing TX delay. So you > > > pass PHY_INTERFACE_MODE_RGMII_TXID to the PHY? It is not clear from > > > this patch, i don't see any code mentioning > > > PHY_INTERFACE_MODE_RGMII_TXID. Could you point me at that code. > > > > > > Andrew > > > > The phy on the board I have is YT8531, The config code is here: > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/motorcomm.c#n868 > > This PHY should be able to do rgmii-id, so there is no need for the > MAC to add delays. We encourage that setup in linux, so all RGMII > MAC/PHY pairs are the same, the PHY add the delays. > Yes, this is what I have done at the beginning. At first I only set up the phy setting and not set the config in the syscon. But I got a weird thing: the phy lookback test is timeout. Although the datasheet told it just adds a internal delay for the phy, I suspect sophgo does something more to set this delay. Regards, Inochi
> Yes, this is what I have done at the beginning. At first I only > set up the phy setting and not set the config in the syscon. > But I got a weird thing: the phy lookback test is timeout. > Although the datasheet told it just adds a internal delay for > the phy, I suspect sophgo does something more to set this delay. You need to understand what is going on here. Just because it works does not mean it is correct. Andrew
On Wed, Oct 23, 2024 at 02:42:16PM +0200, Andrew Lunn wrote: > > Yes, this is what I have done at the beginning. At first I only > > set up the phy setting and not set the config in the syscon. > > But I got a weird thing: the phy lookback test is timeout. > > Although the datasheet told it just adds a internal delay for > > the phy, I suspect sophgo does something more to set this delay. > > You need to understand what is going on here. Just because it works > does not mean it is correct. > It seems like there is a missing info in the SG2044 doc: setting the syscon internal delay bit is not enabling the internal mac delay, but disable it. Now everything seems like normal: the mac adds no delay, and the phy adds its delay. The sophgo have already confirmed this is a firmware issue that does not set up the mac delay correctly and will fix this in the firmware, so the kernal can always have not mac delay. Since this will be fixed in the firmware and this interface is not exposed to the kernel, I will remove the code setting the syscon bit. Thanks for your effort on this. Regards, Inochi
On Thu, Oct 24, 2024 at 06:36:06AM +0800, Inochi Amaoto wrote: > On Wed, Oct 23, 2024 at 02:42:16PM +0200, Andrew Lunn wrote: > > > Yes, this is what I have done at the beginning. At first I only > > > set up the phy setting and not set the config in the syscon. > > > But I got a weird thing: the phy lookback test is timeout. > > > Although the datasheet told it just adds a internal delay for > > > the phy, I suspect sophgo does something more to set this delay. > > > > You need to understand what is going on here. Just because it works > > does not mean it is correct. > > > > It seems like there is a missing info in the SG2044 doc: setting the > syscon internal delay bit is not enabling the internal mac delay, but > disable it. Now everything seems like normal: the mac adds no delay, > and the phy adds its delay. That makes a lot more sense. Thanks for digging into the details. Andrew
Hello, On Mon, Oct 21, 2024 at 06:36:17PM +0800, Inochi Amaoto wrote: > +static struct platform_driver sophgo_dwmac_driver = { > + .probe = sophgo_dwmac_probe, > + .remove_new = stmmac_pltfr_remove, > + .driver = { > + .name = "sophgo-dwmac", > + .pm = &stmmac_pltfr_pm_ops, > + .of_match_table = sophgo_dwmac_match, > + }, > +}; After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Please just drop "_new". Best regards Uwe
On Thu, Oct 24, 2024 at 05:37:03PM +0200, Uwe Kleine-König wrote: > Hello, > > On Mon, Oct 21, 2024 at 06:36:17PM +0800, Inochi Amaoto wrote: > > +static struct platform_driver sophgo_dwmac_driver = { > > + .probe = sophgo_dwmac_probe, > > + .remove_new = stmmac_pltfr_remove, > > + .driver = { > > + .name = "sophgo-dwmac", > > + .pm = &stmmac_pltfr_pm_ops, > > + .of_match_table = sophgo_dwmac_match, > > + }, > > +}; > > After commit 0edb555a65d1 ("platform: Make platform_driver::remove() > return void") .remove() is (again) the right callback to implement for > platform drivers. Please just drop "_new". > > Best regards > Uwe Thanks, I will fix it. Regards, Inochi
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig index 05cc07b8f48c..bc44b21c593f 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig @@ -169,6 +169,17 @@ config DWMAC_SOCFPGA for the stmmac device driver. This driver is used for arria5 and cyclone5 FPGA SoCs. +config DWMAC_SOPHGO + tristate "Sophgo dwmac support" + depends on OF && (ARCH_SOPHGO || COMPILE_TEST) + default m if ARCH_SOPHGO + help + Support for ethernet controllers on Sophgo RISC-V SoCs + + This selects the Sophgo SoC specific glue layer support + for the stmmac device driver. This driver is used for the + ethernet controllers on various Sophgo SoCs. + config DWMAC_STARFIVE tristate "StarFive dwmac support" depends on OF && (ARCH_STARFIVE || COMPILE_TEST) diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile index c2f0e91f6bf8..e1287b53047b 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Makefile +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile @@ -23,6 +23,7 @@ obj-$(CONFIG_DWMAC_QCOM_ETHQOS) += dwmac-qcom-ethqos.o obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o obj-$(CONFIG_DWMAC_RZN1) += dwmac-rzn1.o obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o +obj-$(CONFIG_DWMAC_SOPHGO) += dwmac-sophgo.o obj-$(CONFIG_DWMAC_STARFIVE) += dwmac-starfive.o obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c new file mode 100644 index 000000000000..83c67c061182 --- /dev/null +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c @@ -0,0 +1,132 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Sophgo DWMAC platform driver + * + * Copyright (C) 2024 Inochi Amaoto <inochiama@gmail.com> + * + */ + +#include <linux/bits.h> +#include <linux/mod_devicetable.h> +#include <linux/platform_device.h> +#include <linux/property.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> + +#include "stmmac_platform.h" + +struct sophgo_dwmac { + struct device *dev; + struct clk *clk_tx; +}; + +#define DWMAC_SG2044_FLAG_USE_RX_DELAY BIT(16) + +static void sophgo_dwmac_fix_mac_speed(void *priv, unsigned int speed, unsigned int mode) +{ + struct sophgo_dwmac *dwmac = priv; + unsigned long rate; + int ret; + + switch (speed) { + case SPEED_1000: + rate = 125000000; + break; + case SPEED_100: + rate = 25000000; + break; + case SPEED_10: + rate = 2500000; + break; + default: + dev_err(dwmac->dev, "invalid speed %u\n", speed); + break; + } + + ret = clk_set_rate(dwmac->clk_tx, rate); + if (ret) + dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate); +} + +static int sophgo_sg2044_dwmac_init(struct platform_device *pdev, + struct plat_stmmacenet_data *plat_dat, + struct stmmac_resources *stmmac_res) +{ + struct sophgo_dwmac *dwmac; + struct regmap *regmap; + unsigned int args[2]; + int ret; + + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL); + if (!dwmac) + return -ENOMEM; + + dwmac->clk_tx = devm_clk_get_enabled(&pdev->dev, "tx"); + if (IS_ERR(dwmac->clk_tx)) + return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->clk_tx), + "failed to get tx clock\n"); + + regmap = syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node, + "sophgo,syscon", + 2, args); + if (IS_ERR(regmap)) + return dev_err_probe(&pdev->dev, PTR_ERR(regmap), + "failed to get the regmap\n"); + + ret = regmap_set_bits(regmap, args[0], DWMAC_SG2044_FLAG_USE_RX_DELAY); + if (ret) + return dev_err_probe(&pdev->dev, ret, + "failed to set the phy rx delay\n"); + + dwmac->dev = &pdev->dev; + plat_dat->bsp_priv = dwmac; + plat_dat->flags |= STMMAC_FLAG_SPH_DISABLE; + plat_dat->fix_mac_speed = sophgo_dwmac_fix_mac_speed; + plat_dat->multicast_filter_bins = 0; + plat_dat->unicast_filter_entries = 1; + + return 0; +} + +static int sophgo_dwmac_probe(struct platform_device *pdev) +{ + struct plat_stmmacenet_data *plat_dat; + struct stmmac_resources stmmac_res; + int ret; + + ret = stmmac_get_platform_resources(pdev, &stmmac_res); + if (ret) + return dev_err_probe(&pdev->dev, ret, + "failed to get resources\n"); + + plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return dev_err_probe(&pdev->dev, PTR_ERR(plat_dat), + "dt configuration failed\n"); + + ret = sophgo_sg2044_dwmac_init(pdev, plat_dat, &stmmac_res); + if (ret) + return ret; + + return stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); +} + +static const struct of_device_id sophgo_dwmac_match[] = { + { .compatible = "sophgo,sg2044-dwmac" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, sophgo_dwmac_match); + +static struct platform_driver sophgo_dwmac_driver = { + .probe = sophgo_dwmac_probe, + .remove_new = stmmac_pltfr_remove, + .driver = { + .name = "sophgo-dwmac", + .pm = &stmmac_pltfr_pm_ops, + .of_match_table = sophgo_dwmac_match, + }, +}; +module_platform_driver(sophgo_dwmac_driver); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Sophgo DWMAC platform driver");
Adds Sophgo dwmac driver support on the Sophgo SG2044 SoC. Signed-off-by: Inochi Amaoto <inochiama@gmail.com> --- drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../ethernet/stmicro/stmmac/dwmac-sophgo.c | 132 ++++++++++++++++++ 3 files changed, 144 insertions(+) create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sophgo.c