| Message ID | 1730705521-23081-8-git-send-email-shawn.lin@rock-chips.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Initial support for RK3576 UFS controller | expand |
在 2024/11/4 18:57, Ulf Hansson 写道: > On Mon, 4 Nov 2024 at 08:34, Shawn Lin <shawn.lin@rock-chips.com> wrote: >> >> RK3576 SoC contains a UFS controller, add initial support for it. >> The features are: >> (1) support UFS 2.0 features >> (2) High speed up to HS-G3 >> (3) 2RX-2TX lanes >> (4) auto H8 entry and exit >> >> Software limitation: >> (1) HCE procedure: enable controller->enable intr->dme_reset->dme_enable >> (2) disable unipro timeout values before power mode change >> >> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> >> --- >> >> Changes in v4: >> - deal with power domain of rpm and spm suggested by Ulf >> - Fix typo and disable clks in ufs_rockchip_remove >> - remove clk_disable_unprepare(host->ref_out_clk) from >> ufs_rockchip_remove >> > > [...] > >> +#ifdef CONFIG_PM >> +static int ufs_rockchip_runtime_suspend(struct device *dev) >> +{ >> + struct ufs_hba *hba = dev_get_drvdata(dev); >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + >> + clk_disable_unprepare(host->ref_out_clk); >> + >> + /* Shouldn't power down if rpm_lvl is less than level 5. */ >> + dev_pm_genpd_rpm_always_on(dev, hba->rpm_lvl < UFS_PM_LVL_5 ? true : false); >> + >> + return ufshcd_runtime_suspend(dev); >> +} >> + >> +static int ufs_rockchip_runtime_resume(struct device *dev) >> +{ >> + struct ufs_hba *hba = dev_get_drvdata(dev); >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + int err; >> + >> + err = clk_prepare_enable(host->ref_out_clk); >> + if (err) { >> + dev_err(hba->dev, "failed to enable ref out clock %d\n", err); >> + return err; >> + } >> + >> + reset_control_assert(host->rst); >> + usleep_range(1, 2); >> + reset_control_deassert(host->rst); >> + >> + return ufshcd_runtime_resume(dev); >> +} >> +#endif >> + >> +#ifdef CONFIG_PM_SLEEP >> +static int ufs_rockchip_system_suspend(struct device *dev) >> +{ >> + struct ufs_hba *hba = dev_get_drvdata(dev); >> + >> + if (hba->spm_lvl < 5) >> + device_set_wakeup_path(dev); > > Please use device_set_awake_path() instead. > > Ideally all users of device_set_wakeup_path() should convert into > device_set_awake_path(), it's just that we haven't been able to > complete the conversion yet. Will use device_set_awake_path(). > >> + else >> + device_clr_wakeup_path(dev); > > This isn't needed. The flag is getting cleared in device_prepare(). > >> + >> + return ufshcd_system_suspend(dev); > > Don't you want to disable the clock during system suspend too? If the > device is runtime resumed at this point, the clock will be left > enabled, no? Good point. Will fix it. > >> +} >> +#endif >> + >> +static const struct dev_pm_ops ufs_rockchip_pm_ops = { >> + SET_SYSTEM_SLEEP_PM_OPS(ufs_rockchip_system_suspend, ufshcd_system_resume) >> + SET_RUNTIME_PM_OPS(ufs_rockchip_runtime_suspend, ufs_rockchip_runtime_resume, NULL) >> + .prepare = ufshcd_suspend_prepare, >> + .complete = ufshcd_resume_complete, >> +}; >> + > > [...] > > Kind regards > Uffe >
On Mon, Nov 04, 2024 at 03:32:01PM +0800, Shawn Lin wrote: > RK3576 SoC contains a UFS controller, add initial support for it. > The features are: > (1) support UFS 2.0 features > (2) High speed up to HS-G3 > (3) 2RX-2TX lanes > (4) auto H8 entry and exit > > Software limitation: > (1) HCE procedure: enable controller->enable intr->dme_reset->dme_enable > (2) disable unipro timeout values before power mode change > > Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> > --- > > Changes in v4: > - deal with power domain of rpm and spm suggested by Ulf > - Fix typo and disable clks in ufs_rockchip_remove > - remove clk_disable_unprepare(host->ref_out_clk) from > ufs_rockchip_remove > > Changes in v3: > - reword Kconfig description > - elaborate more about controller in commit msg > - use rockchip,rk3576-ufshc for compatible > - remove useless header file > - remove inline for ufshcd_is_device_present > - use usleep_range instead > - remove initialization, reverse Xmas order > - remove useless varibles > - check vops for null > - other small fixes for err path > - remove pm_runtime_set_active > - fix the active and inactive reset-gpios logic > - fix rpm_lvl and spm_lvl to 5 and move to end of probe path > - remove unnecessary system PM callbacks > - use UFSHCI_QUIRK_DME_RESET_ENABLE_AFTER_HCE instead > of UFSHCI_QUIRK_BROKEN_HCE > > Changes in v2: None > > drivers/ufs/host/Kconfig | 12 ++ > drivers/ufs/host/Makefile | 1 + > drivers/ufs/host/ufs-rockchip.c | 340 ++++++++++++++++++++++++++++++++++++++++ > drivers/ufs/host/ufs-rockchip.h | 51 ++++++ > 4 files changed, 404 insertions(+) > create mode 100644 drivers/ufs/host/ufs-rockchip.c > create mode 100644 drivers/ufs/host/ufs-rockchip.h > > diff --git a/drivers/ufs/host/Kconfig b/drivers/ufs/host/Kconfig > index 580c8d0..191fbd7 100644 > --- a/drivers/ufs/host/Kconfig > +++ b/drivers/ufs/host/Kconfig > @@ -142,3 +142,15 @@ config SCSI_UFS_SPRD > > Select this if you have UFS controller on Unisoc chipset. > If unsure, say N. > + > +config SCSI_UFS_ROCKCHIP > + tristate "Rockchip UFS host controller driver" > + depends on SCSI_UFSHCD_PLATFORM && (ARCH_ROCKCHIP || COMPILE_TEST) > + help > + This selects the Rockchip specific additions to UFSHCD platform driver. > + UFS host on Rockchip needs some vendor specific configuration before > + accessing the hardware which includes PHY configuration and vendor > + specific registers. > + > + Select this if you have UFS controller on Rockchip chipset. > + If unsure, say N. > diff --git a/drivers/ufs/host/Makefile b/drivers/ufs/host/Makefile > index 4573aea..2f97feb 100644 > --- a/drivers/ufs/host/Makefile > +++ b/drivers/ufs/host/Makefile > @@ -10,5 +10,6 @@ obj-$(CONFIG_SCSI_UFSHCD_PLATFORM) += ufshcd-pltfrm.o > obj-$(CONFIG_SCSI_UFS_HISI) += ufs-hisi.o > obj-$(CONFIG_SCSI_UFS_MEDIATEK) += ufs-mediatek.o > obj-$(CONFIG_SCSI_UFS_RENESAS) += ufs-renesas.o > +obj-$(CONFIG_SCSI_UFS_ROCKCHIP) += ufs-rockchip.o > obj-$(CONFIG_SCSI_UFS_SPRD) += ufs-sprd.o > obj-$(CONFIG_SCSI_UFS_TI_J721E) += ti-j721e-ufs.o > diff --git a/drivers/ufs/host/ufs-rockchip.c b/drivers/ufs/host/ufs-rockchip.c > new file mode 100644 > index 0000000..9c277bc > --- /dev/null > +++ b/drivers/ufs/host/ufs-rockchip.c > @@ -0,0 +1,340 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Rockchip UFS Host Controller driver > + * > + * Copyright (C) 2024 Rockchip Electronics Co.Ltd. > + */ > + > +#include <linux/clk.h> > +#include <linux/gpio.h> > +#include <linux/mfd/syscon.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/pm_domain.h> > +#include <linux/pm_wakeup.h> > +#include <linux/regmap.h> > +#include <linux/reset.h> > + > +#include <ufs/ufshcd.h> > +#include <ufs/unipro.h> > +#include "ufshcd-pltfrm.h" > +#include "ufs-rockchip.h" > + > +static int ufs_rockchip_hce_enable_notify(struct ufs_hba *hba, > + enum ufs_notify_change_status status) > +{ > + int err = 0; > + > + if (status == POST_CHANGE) > + err = ufshcd_vops_phy_initialization(hba); return ufshcd_vops_phy_initialization() > + > + return err; return 0 > +} > + > +static void ufs_rockchip_set_pm_lvl(struct ufs_hba *hba) > +{ > + hba->rpm_lvl = UFS_PM_LVL_5; Are you sure that you want to power down both the device and link during runtime suspend? > + hba->spm_lvl = UFS_PM_LVL_5; > +} > + > +static int ufs_rockchip_rk3576_phy_init(struct ufs_hba *hba) > +{ > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > + > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(PA_LOCAL_TX_LCC_ENABLE, 0x0), 0x0); > + /* enable the mphy DME_SET cfg */ > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x200, 0x0), 0x40); > + for (int i = 0; i < 2; i++) { > + /* Configuration M-TX */ > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xaa, SEL_TX_LANE0 + i), 0x06); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xa9, SEL_TX_LANE0 + i), 0x02); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xad, SEL_TX_LANE0 + i), 0x44); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xac, SEL_TX_LANE0 + i), 0xe6); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xab, SEL_TX_LANE0 + i), 0x07); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x94, SEL_TX_LANE0 + i), 0x93); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x93, SEL_TX_LANE0 + i), 0xc9); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x7f, SEL_TX_LANE0 + i), 0x00); > + /* Configuration M-RX */ > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x12, SEL_RX_LANE0 + i), 0x06); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x11, SEL_RX_LANE0 + i), 0x00); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1d, SEL_RX_LANE0 + i), 0x58); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1c, SEL_RX_LANE0 + i), 0x8c); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1b, SEL_RX_LANE0 + i), 0x02); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x25, SEL_RX_LANE0 + i), 0xf6); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x2f, SEL_RX_LANE0 + i), 0x69); > + } > + /* disable the mphy DME_SET cfg */ > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x200, 0x0), 0x00); > + > + ufs_sys_writel(host->mphy_base, 0x80, 0x08C); > + ufs_sys_writel(host->mphy_base, 0xB5, 0x110); > + ufs_sys_writel(host->mphy_base, 0xB5, 0x250); > + > + ufs_sys_writel(host->mphy_base, 0x03, 0x134); > + ufs_sys_writel(host->mphy_base, 0x03, 0x274); > + > + ufs_sys_writel(host->mphy_base, 0x38, 0x0E0); > + ufs_sys_writel(host->mphy_base, 0x38, 0x220); > + > + ufs_sys_writel(host->mphy_base, 0x50, 0x164); > + ufs_sys_writel(host->mphy_base, 0x50, 0x2A4); > + > + ufs_sys_writel(host->mphy_base, 0x80, 0x178); > + ufs_sys_writel(host->mphy_base, 0x80, 0x2B8); > + > + ufs_sys_writel(host->mphy_base, 0x18, 0x1B0); > + ufs_sys_writel(host->mphy_base, 0x18, 0x2F0); > + > + ufs_sys_writel(host->mphy_base, 0x03, 0x128); > + ufs_sys_writel(host->mphy_base, 0x03, 0x268); > + > + ufs_sys_writel(host->mphy_base, 0x20, 0x12C); > + ufs_sys_writel(host->mphy_base, 0x20, 0x26C); > + > + ufs_sys_writel(host->mphy_base, 0xC0, 0x120); > + ufs_sys_writel(host->mphy_base, 0xC0, 0x260); > + > + ufs_sys_writel(host->mphy_base, 0x03, 0x094); > + > + ufs_sys_writel(host->mphy_base, 0x03, 0x1B4); > + ufs_sys_writel(host->mphy_base, 0x03, 0x2F4); > + > + ufs_sys_writel(host->mphy_base, 0xC0, 0x08C); > + usleep_range(1, 2); > + ufs_sys_writel(host->mphy_base, 0x00, 0x08C); > + > + usleep_range(200, 250); > + /* start link up */ > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(MIB_T_DBG_CPORT_TX_ENDIAN, 0), 0x0); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(MIB_T_DBG_CPORT_RX_ENDIAN, 0), 0x0); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID, 0), 0x0); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID_VALID, 0), 0x1); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(T_PEERDEVICEID, 0), 0x1); > + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(T_CONNECTIONSTATE, 0), 0x1); I assume that the PHY doesn't have any separate resources like clocks and you just need to write these registers. > + > + return 0; > +} > + > +static int ufs_rockchip_common_init(struct ufs_hba *hba) > +{ > + struct device *dev = hba->dev; > + struct platform_device *pdev = to_platform_device(dev); > + struct ufs_rockchip_host *host; > + int err; Reverse Xmas tree please (but I don't insist). > + > + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); > + if (!host) > + return -ENOMEM; > + > + /* system control register for hci */ > + host->ufs_sys_ctrl = devm_platform_ioremap_resource_byname(pdev, "hci_grf"); > + if (IS_ERR(host->ufs_sys_ctrl)) > + return dev_err_probe(dev, PTR_ERR(host->ufs_sys_ctrl), > + "cannot ioremap for hci system control register\n"); "Failed to map HCI system control registers" Similar for other messages below. > + > + /* system control register for mphy */ > + host->ufs_phy_ctrl = devm_platform_ioremap_resource_byname(pdev, "mphy_grf"); > + if (IS_ERR(host->ufs_phy_ctrl)) > + return dev_err_probe(dev, PTR_ERR(host->ufs_phy_ctrl), > + "cannot ioremap for mphy system control register\n"); > + > + /* mphy base register */ > + host->mphy_base = devm_platform_ioremap_resource_byname(pdev, "mphy"); > + if (IS_ERR(host->mphy_base)) > + return dev_err_probe(dev, PTR_ERR(host->mphy_base), > + "cannot ioremap for mphy base register\n"); > + > + host->rst = devm_reset_control_array_get_exclusive(dev); > + if (IS_ERR(host->rst)) > + return dev_err_probe(dev, PTR_ERR(host->rst), > + "failed to get reset control\n"); > + > + reset_control_assert(host->rst); > + usleep_range(1, 2); > + reset_control_deassert(host->rst); > + > + host->ref_out_clk = devm_clk_get_enabled(dev, "ref_out"); > + if (IS_ERR(host->ref_out_clk)) > + return dev_err_probe(dev, PTR_ERR(host->ref_out_clk), > + "ref_out unavailable\n"); > + > + host->rst_gpio = devm_gpiod_get(&pdev->dev, "reset", GPIOD_OUT_LOW); > + if (IS_ERR(host->rst_gpio)) > + return dev_err_probe(&pdev->dev, PTR_ERR(host->rst_gpio), > + "invalid reset-gpios property in node\n"); > + > + host->clks[0].id = "core"; > + host->clks[1].id = "pclk"; > + host->clks[2].id = "pclk_mphy"; No need to hardcode clocks in the driver. You can just use clk_bulk_get_all() to get the clocks from DT. DT binding should make sure that the clocks are present in DT. > + err = devm_clk_bulk_get_optional(dev, UFS_MAX_CLKS, host->clks); > + if (err) > + return dev_err_probe(dev, err, "failed to get clocks\n"); > + > + err = clk_bulk_prepare_enable(UFS_MAX_CLKS, host->clks); > + if (err) > + return dev_err_probe(dev, err, "failed to enable clocks\n"); > + > + host->hba = hba; > + > + ufshcd_set_variant(hba, host); > + > + return 0; > +} > + > +static int ufs_rockchip_rk3576_init(struct ufs_hba *hba) > +{ > + struct device *dev = hba->dev; > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > + int ret; > + > + hba->quirks = UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING | > + UFSHCI_QUIRK_DME_RESET_ENABLE_AFTER_HCE; > + > + /* Enable BKOPS when suspend */ > + hba->caps |= UFSHCD_CAP_AUTO_BKOPS_SUSPEND; > + /* Enable putting device into deep sleep */ > + hba->caps |= UFSHCD_CAP_DEEPSLEEP; > + /* Enable devfreq of UFS */ > + hba->caps |= UFSHCD_CAP_CLK_SCALING; > + /* Enable WriteBooster */ > + hba->caps |= UFSHCD_CAP_WB_EN; > + > + host->pd_id = RK3576_PD_UFS; > + > + ret = ufs_rockchip_common_init(hba); > + if (ret) > + return dev_err_probe(dev, ret, "ufs common init fail\n"); > + > + return 0; > +} > + > +static int ufs_rockchip_device_reset(struct ufs_hba *hba) > +{ > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > + > + /* Active the reset-gpios */ No need of this and below comment. > + gpiod_set_value_cansleep(host->rst_gpio, 1); > + usleep_range(20, 25); > + > + /* Inactive the reset-gpios */ > + gpiod_set_value_cansleep(host->rst_gpio, 0); > + usleep_range(20, 25); > + > + return 0; > +} > + > +static const struct ufs_hba_variant_ops ufs_hba_rk3576_vops = { > + .name = "rk3576", Unless you expect different variant ops for each chipset, you can just use "rockchip". > + .init = ufs_rockchip_rk3576_init, > + .device_reset = ufs_rockchip_device_reset, > + .hce_enable_notify = ufs_rockchip_hce_enable_notify, > + .phy_initialization = ufs_rockchip_rk3576_phy_init, > +}; > + > +static const struct of_device_id ufs_rockchip_of_match[] = { > + { .compatible = "rockchip,rk3576-ufshc", .data = &ufs_hba_rk3576_vops }, > +}; > +MODULE_DEVICE_TABLE(of, ufs_rockchip_of_match); > + > +static int ufs_rockchip_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + const struct ufs_hba_variant_ops *vops; > + struct ufs_hba *hba; > + int err; > + > + vops = device_get_match_data(dev); > + if (!vops) > + return dev_err_probe(dev, -EINVAL, "ufs_hba_variant_ops not defined.\n"); > + > + err = ufshcd_pltfrm_init(pdev, vops); > + if (err) > + return dev_err_probe(dev, err, "ufshcd_pltfrm_init failed\n"); > + > + hba = platform_get_drvdata(pdev); > + /* Set the default desired pm level in case no users set via sysfs */ > + ufs_rockchip_set_pm_lvl(hba); > + > + return 0; > +} > + > +static void ufs_rockchip_remove(struct platform_device *pdev) > +{ > + struct ufs_hba *hba = platform_get_drvdata(pdev); > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > + > + pm_runtime_forbid(&pdev->dev); > + pm_runtime_get_noresume(&pdev->dev); Why do you need these? You are not incrementing the refcount in probe() and there is no auto PM involved. > + ufshcd_remove(hba); > + ufshcd_dealloc_host(hba); > + clk_bulk_disable_unprepare(UFS_MAX_CLKS, host->clks); > +} > + > +#ifdef CONFIG_PM > +static int ufs_rockchip_runtime_suspend(struct device *dev) > +{ > + struct ufs_hba *hba = dev_get_drvdata(dev); > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > + > + clk_disable_unprepare(host->ref_out_clk); > + > + /* Shouldn't power down if rpm_lvl is less than level 5. */ > + dev_pm_genpd_rpm_always_on(dev, hba->rpm_lvl < UFS_PM_LVL_5 ? true : false); > + > + return ufshcd_runtime_suspend(dev); > +} > + > +static int ufs_rockchip_runtime_resume(struct device *dev) > +{ > + struct ufs_hba *hba = dev_get_drvdata(dev); > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > + int err; > + > + err = clk_prepare_enable(host->ref_out_clk); > + if (err) { > + dev_err(hba->dev, "failed to enable ref out clock %d\n", err); > + return err; > + } > + > + reset_control_assert(host->rst); > + usleep_range(1, 2); > + reset_control_deassert(host->rst); > + > + return ufshcd_runtime_resume(dev); > +} > +#endif > + > +#ifdef CONFIG_PM_SLEEP > +static int ufs_rockchip_system_suspend(struct device *dev) > +{ > + struct ufs_hba *hba = dev_get_drvdata(dev); > + > + if (hba->spm_lvl < 5) > + device_set_wakeup_path(dev); > + else > + device_clr_wakeup_path(dev); This should be taken care by driver core. - Mani
Hi Mani, 在 2024/11/9 20:12, Manivannan Sadhasivam 写道: > On Mon, Nov 04, 2024 at 03:32:01PM +0800, Shawn Lin wrote: >> RK3576 SoC contains a UFS controller, add initial support for it. >> The features are: >> (1) support UFS 2.0 features >> (2) High speed up to HS-G3 >> (3) 2RX-2TX lanes >> (4) auto H8 entry and exit >> >> Software limitation: >> (1) HCE procedure: enable controller->enable intr->dme_reset->dme_enable >> (2) disable unipro timeout values before power mode change >> >> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> >> --- >> >> Changes in v4: >> - deal with power domain of rpm and spm suggested by Ulf >> - Fix typo and disable clks in ufs_rockchip_remove >> - remove clk_disable_unprepare(host->ref_out_clk) from >> ufs_rockchip_remove >> >> Changes in v3: >> - reword Kconfig description >> - elaborate more about controller in commit msg >> - use rockchip,rk3576-ufshc for compatible >> - remove useless header file >> - remove inline for ufshcd_is_device_present >> - use usleep_range instead >> - remove initialization, reverse Xmas order >> - remove useless varibles >> - check vops for null >> - other small fixes for err path >> - remove pm_runtime_set_active >> - fix the active and inactive reset-gpios logic >> - fix rpm_lvl and spm_lvl to 5 and move to end of probe path >> - remove unnecessary system PM callbacks >> - use UFSHCI_QUIRK_DME_RESET_ENABLE_AFTER_HCE instead >> of UFSHCI_QUIRK_BROKEN_HCE >> >> Changes in v2: None >> >> drivers/ufs/host/Kconfig | 12 ++ >> drivers/ufs/host/Makefile | 1 + >> drivers/ufs/host/ufs-rockchip.c | 340 ++++++++++++++++++++++++++++++++++++++++ >> drivers/ufs/host/ufs-rockchip.h | 51 ++++++ >> 4 files changed, 404 insertions(+) >> create mode 100644 drivers/ufs/host/ufs-rockchip.c >> create mode 100644 drivers/ufs/host/ufs-rockchip.h >> >> diff --git a/drivers/ufs/host/Kconfig b/drivers/ufs/host/Kconfig >> index 580c8d0..191fbd7 100644 >> --- a/drivers/ufs/host/Kconfig >> +++ b/drivers/ufs/host/Kconfig >> @@ -142,3 +142,15 @@ config SCSI_UFS_SPRD >> >> Select this if you have UFS controller on Unisoc chipset. >> If unsure, say N. >> + >> +config SCSI_UFS_ROCKCHIP >> + tristate "Rockchip UFS host controller driver" >> + depends on SCSI_UFSHCD_PLATFORM && (ARCH_ROCKCHIP || COMPILE_TEST) >> + help >> + This selects the Rockchip specific additions to UFSHCD platform driver. >> + UFS host on Rockchip needs some vendor specific configuration before >> + accessing the hardware which includes PHY configuration and vendor >> + specific registers. >> + >> + Select this if you have UFS controller on Rockchip chipset. >> + If unsure, say N. >> diff --git a/drivers/ufs/host/Makefile b/drivers/ufs/host/Makefile >> index 4573aea..2f97feb 100644 >> --- a/drivers/ufs/host/Makefile >> +++ b/drivers/ufs/host/Makefile >> @@ -10,5 +10,6 @@ obj-$(CONFIG_SCSI_UFSHCD_PLATFORM) += ufshcd-pltfrm.o >> obj-$(CONFIG_SCSI_UFS_HISI) += ufs-hisi.o >> obj-$(CONFIG_SCSI_UFS_MEDIATEK) += ufs-mediatek.o >> obj-$(CONFIG_SCSI_UFS_RENESAS) += ufs-renesas.o >> +obj-$(CONFIG_SCSI_UFS_ROCKCHIP) += ufs-rockchip.o >> obj-$(CONFIG_SCSI_UFS_SPRD) += ufs-sprd.o >> obj-$(CONFIG_SCSI_UFS_TI_J721E) += ti-j721e-ufs.o >> diff --git a/drivers/ufs/host/ufs-rockchip.c b/drivers/ufs/host/ufs-rockchip.c >> new file mode 100644 >> index 0000000..9c277bc >> --- /dev/null >> +++ b/drivers/ufs/host/ufs-rockchip.c >> @@ -0,0 +1,340 @@ >> +// SPDX-License-Identifier: GPL-2.0-only >> +/* >> + * Rockchip UFS Host Controller driver >> + * >> + * Copyright (C) 2024 Rockchip Electronics Co.Ltd. >> + */ >> + >> +#include <linux/clk.h> >> +#include <linux/gpio.h> >> +#include <linux/mfd/syscon.h> >> +#include <linux/of.h> >> +#include <linux/platform_device.h> >> +#include <linux/pm_domain.h> >> +#include <linux/pm_wakeup.h> >> +#include <linux/regmap.h> >> +#include <linux/reset.h> >> + >> +#include <ufs/ufshcd.h> >> +#include <ufs/unipro.h> >> +#include "ufshcd-pltfrm.h" >> +#include "ufs-rockchip.h" >> + >> +static int ufs_rockchip_hce_enable_notify(struct ufs_hba *hba, >> + enum ufs_notify_change_status status) >> +{ >> + int err = 0; >> + >> + if (status == POST_CHANGE) >> + err = ufshcd_vops_phy_initialization(hba); > > return ufshcd_vops_phy_initialization() > >> + >> + return err; > > return 0 Will fix this. > >> +} >> + >> +static void ufs_rockchip_set_pm_lvl(struct ufs_hba *hba) >> +{ >> + hba->rpm_lvl = UFS_PM_LVL_5; > > Are you sure that you want to power down both the device and link during runtime > suspend? > Yes, this is what we need for our product by default. >> + hba->spm_lvl = UFS_PM_LVL_5; >> +} >> + >> +static int ufs_rockchip_rk3576_phy_init(struct ufs_hba *hba) >> +{ >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(PA_LOCAL_TX_LCC_ENABLE, 0x0), 0x0); >> + /* enable the mphy DME_SET cfg */ >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x200, 0x0), 0x40); >> + for (int i = 0; i < 2; i++) { >> + /* Configuration M-TX */ >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xaa, SEL_TX_LANE0 + i), 0x06); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xa9, SEL_TX_LANE0 + i), 0x02); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xad, SEL_TX_LANE0 + i), 0x44); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xac, SEL_TX_LANE0 + i), 0xe6); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xab, SEL_TX_LANE0 + i), 0x07); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x94, SEL_TX_LANE0 + i), 0x93); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x93, SEL_TX_LANE0 + i), 0xc9); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x7f, SEL_TX_LANE0 + i), 0x00); >> + /* Configuration M-RX */ >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x12, SEL_RX_LANE0 + i), 0x06); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x11, SEL_RX_LANE0 + i), 0x00); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1d, SEL_RX_LANE0 + i), 0x58); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1c, SEL_RX_LANE0 + i), 0x8c); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1b, SEL_RX_LANE0 + i), 0x02); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x25, SEL_RX_LANE0 + i), 0xf6); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x2f, SEL_RX_LANE0 + i), 0x69); >> + } >> + /* disable the mphy DME_SET cfg */ >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x200, 0x0), 0x00); >> + >> + ufs_sys_writel(host->mphy_base, 0x80, 0x08C); >> + ufs_sys_writel(host->mphy_base, 0xB5, 0x110); >> + ufs_sys_writel(host->mphy_base, 0xB5, 0x250); >> + >> + ufs_sys_writel(host->mphy_base, 0x03, 0x134); >> + ufs_sys_writel(host->mphy_base, 0x03, 0x274); >> + >> + ufs_sys_writel(host->mphy_base, 0x38, 0x0E0); >> + ufs_sys_writel(host->mphy_base, 0x38, 0x220); >> + >> + ufs_sys_writel(host->mphy_base, 0x50, 0x164); >> + ufs_sys_writel(host->mphy_base, 0x50, 0x2A4); >> + >> + ufs_sys_writel(host->mphy_base, 0x80, 0x178); >> + ufs_sys_writel(host->mphy_base, 0x80, 0x2B8); >> + >> + ufs_sys_writel(host->mphy_base, 0x18, 0x1B0); >> + ufs_sys_writel(host->mphy_base, 0x18, 0x2F0); >> + >> + ufs_sys_writel(host->mphy_base, 0x03, 0x128); >> + ufs_sys_writel(host->mphy_base, 0x03, 0x268); >> + >> + ufs_sys_writel(host->mphy_base, 0x20, 0x12C); >> + ufs_sys_writel(host->mphy_base, 0x20, 0x26C); >> + >> + ufs_sys_writel(host->mphy_base, 0xC0, 0x120); >> + ufs_sys_writel(host->mphy_base, 0xC0, 0x260); >> + >> + ufs_sys_writel(host->mphy_base, 0x03, 0x094); >> + >> + ufs_sys_writel(host->mphy_base, 0x03, 0x1B4); >> + ufs_sys_writel(host->mphy_base, 0x03, 0x2F4); >> + >> + ufs_sys_writel(host->mphy_base, 0xC0, 0x08C); >> + usleep_range(1, 2); >> + ufs_sys_writel(host->mphy_base, 0x00, 0x08C); >> + >> + usleep_range(200, 250); >> + /* start link up */ >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(MIB_T_DBG_CPORT_TX_ENDIAN, 0), 0x0); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(MIB_T_DBG_CPORT_RX_ENDIAN, 0), 0x0); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID, 0), 0x0); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID_VALID, 0), 0x1); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(T_PEERDEVICEID, 0), 0x1); >> + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(T_CONNECTIONSTATE, 0), 0x1); > > I assume that the PHY doesn't have any separate resources like clocks and you > just need to write these registers. > yes. >> + >> + return 0; >> +} >> + >> +static int ufs_rockchip_common_init(struct ufs_hba *hba) >> +{ >> + struct device *dev = hba->dev; >> + struct platform_device *pdev = to_platform_device(dev); >> + struct ufs_rockchip_host *host; >> + int err; > > Reverse Xmas tree please (but I don't insist). Will fix. > >> + >> + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); >> + if (!host) >> + return -ENOMEM; >> + >> + /* system control register for hci */ >> + host->ufs_sys_ctrl = devm_platform_ioremap_resource_byname(pdev, "hci_grf"); >> + if (IS_ERR(host->ufs_sys_ctrl)) >> + return dev_err_probe(dev, PTR_ERR(host->ufs_sys_ctrl), >> + "cannot ioremap for hci system control register\n"); > > "Failed to map HCI system control registers" > > Similar for other messages below. > >> + >> + /* system control register for mphy */ >> + host->ufs_phy_ctrl = devm_platform_ioremap_resource_byname(pdev, "mphy_grf"); >> + if (IS_ERR(host->ufs_phy_ctrl)) >> + return dev_err_probe(dev, PTR_ERR(host->ufs_phy_ctrl), >> + "cannot ioremap for mphy system control register\n"); >> + >> + /* mphy base register */ >> + host->mphy_base = devm_platform_ioremap_resource_byname(pdev, "mphy"); >> + if (IS_ERR(host->mphy_base)) >> + return dev_err_probe(dev, PTR_ERR(host->mphy_base), >> + "cannot ioremap for mphy base register\n"); >> + >> + host->rst = devm_reset_control_array_get_exclusive(dev); >> + if (IS_ERR(host->rst)) >> + return dev_err_probe(dev, PTR_ERR(host->rst), >> + "failed to get reset control\n"); >> + >> + reset_control_assert(host->rst); >> + usleep_range(1, 2); >> + reset_control_deassert(host->rst); >> + >> + host->ref_out_clk = devm_clk_get_enabled(dev, "ref_out"); >> + if (IS_ERR(host->ref_out_clk)) >> + return dev_err_probe(dev, PTR_ERR(host->ref_out_clk), >> + "ref_out unavailable\n"); >> + >> + host->rst_gpio = devm_gpiod_get(&pdev->dev, "reset", GPIOD_OUT_LOW); >> + if (IS_ERR(host->rst_gpio)) >> + return dev_err_probe(&pdev->dev, PTR_ERR(host->rst_gpio), >> + "invalid reset-gpios property in node\n"); >> + >> + host->clks[0].id = "core"; >> + host->clks[1].id = "pclk"; >> + host->clks[2].id = "pclk_mphy"; > > No need to hardcode clocks in the driver. You can just use clk_bulk_get_all() to > get the clocks from DT. DT binding should make sure that the clocks are present > in DT. Good idea, will fix. > >> + err = devm_clk_bulk_get_optional(dev, UFS_MAX_CLKS, host->clks); >> + if (err) >> + return dev_err_probe(dev, err, "failed to get clocks\n"); >> + >> + err = clk_bulk_prepare_enable(UFS_MAX_CLKS, host->clks); >> + if (err) >> + return dev_err_probe(dev, err, "failed to enable clocks\n"); >> + >> + host->hba = hba; >> + >> + ufshcd_set_variant(hba, host); >> + >> + return 0; >> +} >> + >> +static int ufs_rockchip_rk3576_init(struct ufs_hba *hba) >> +{ >> + struct device *dev = hba->dev; >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + int ret; >> + >> + hba->quirks = UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING | >> + UFSHCI_QUIRK_DME_RESET_ENABLE_AFTER_HCE; >> + >> + /* Enable BKOPS when suspend */ >> + hba->caps |= UFSHCD_CAP_AUTO_BKOPS_SUSPEND; >> + /* Enable putting device into deep sleep */ >> + hba->caps |= UFSHCD_CAP_DEEPSLEEP; >> + /* Enable devfreq of UFS */ >> + hba->caps |= UFSHCD_CAP_CLK_SCALING; >> + /* Enable WriteBooster */ >> + hba->caps |= UFSHCD_CAP_WB_EN; >> + >> + host->pd_id = RK3576_PD_UFS; >> + >> + ret = ufs_rockchip_common_init(hba); >> + if (ret) >> + return dev_err_probe(dev, ret, "ufs common init fail\n"); >> + >> + return 0; >> +} >> + >> +static int ufs_rockchip_device_reset(struct ufs_hba *hba) >> +{ >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + >> + /* Active the reset-gpios */ > > No need of this and below comment. Will remove. > >> + gpiod_set_value_cansleep(host->rst_gpio, 1); >> + usleep_range(20, 25); >> + >> + /* Inactive the reset-gpios */ >> + gpiod_set_value_cansleep(host->rst_gpio, 0); >> + usleep_range(20, 25); >> + >> + return 0; >> +} >> + >> +static const struct ufs_hba_variant_ops ufs_hba_rk3576_vops = { >> + .name = "rk3576", > > Unless you expect different variant ops for each chipset, you can just use > "rockchip". Probably we need a different variant ops, for insatnce, we may seek to fix the hce process problem, also we probably need a different .init process. > >> + .init = ufs_rockchip_rk3576_init, >> + .device_reset = ufs_rockchip_device_reset, >> + .hce_enable_notify = ufs_rockchip_hce_enable_notify, >> + .phy_initialization = ufs_rockchip_rk3576_phy_init, >> +}; >> + >> +static const struct of_device_id ufs_rockchip_of_match[] = { >> + { .compatible = "rockchip,rk3576-ufshc", .data = &ufs_hba_rk3576_vops }, >> +}; >> +MODULE_DEVICE_TABLE(of, ufs_rockchip_of_match); >> + >> +static int ufs_rockchip_probe(struct platform_device *pdev) >> +{ >> + struct device *dev = &pdev->dev; >> + const struct ufs_hba_variant_ops *vops; >> + struct ufs_hba *hba; >> + int err; >> + >> + vops = device_get_match_data(dev); >> + if (!vops) >> + return dev_err_probe(dev, -EINVAL, "ufs_hba_variant_ops not defined.\n"); >> + >> + err = ufshcd_pltfrm_init(pdev, vops); >> + if (err) >> + return dev_err_probe(dev, err, "ufshcd_pltfrm_init failed\n"); >> + >> + hba = platform_get_drvdata(pdev); >> + /* Set the default desired pm level in case no users set via sysfs */ >> + ufs_rockchip_set_pm_lvl(hba); >> + >> + return 0; >> +} >> + >> +static void ufs_rockchip_remove(struct platform_device *pdev) >> +{ >> + struct ufs_hba *hba = platform_get_drvdata(pdev); >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + >> + pm_runtime_forbid(&pdev->dev); >> + pm_runtime_get_noresume(&pdev->dev); > > Why do you need these? You are not incrementing the refcount in probe() and > there is no auto PM involved. Oh, it was a leftover from former version I haven't noticed. Will remove. > >> + ufshcd_remove(hba); >> + ufshcd_dealloc_host(hba); >> + clk_bulk_disable_unprepare(UFS_MAX_CLKS, host->clks); >> +} >> + >> +#ifdef CONFIG_PM >> +static int ufs_rockchip_runtime_suspend(struct device *dev) >> +{ >> + struct ufs_hba *hba = dev_get_drvdata(dev); >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + >> + clk_disable_unprepare(host->ref_out_clk); >> + >> + /* Shouldn't power down if rpm_lvl is less than level 5. */ >> + dev_pm_genpd_rpm_always_on(dev, hba->rpm_lvl < UFS_PM_LVL_5 ? true : false); >> + >> + return ufshcd_runtime_suspend(dev); >> +} >> + >> +static int ufs_rockchip_runtime_resume(struct device *dev) >> +{ >> + struct ufs_hba *hba = dev_get_drvdata(dev); >> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >> + int err; >> + >> + err = clk_prepare_enable(host->ref_out_clk); >> + if (err) { >> + dev_err(hba->dev, "failed to enable ref out clock %d\n", err); >> + return err; >> + } >> + >> + reset_control_assert(host->rst); >> + usleep_range(1, 2); >> + reset_control_deassert(host->rst); >> + >> + return ufshcd_runtime_resume(dev); >> +} >> +#endif >> + >> +#ifdef CONFIG_PM_SLEEP >> +static int ufs_rockchip_system_suspend(struct device *dev) >> +{ >> + struct ufs_hba *hba = dev_get_drvdata(dev); >> + >> + if (hba->spm_lvl < 5) >> + device_set_wakeup_path(dev); >> + else >> + device_clr_wakeup_path(dev); > > This should be taken care by driver core. > > - Mani >
On Mon, Nov 11, 2024 at 09:10:39AM +0800, Shawn Lin wrote: [...] > > > +static void ufs_rockchip_remove(struct platform_device *pdev) > > > +{ > > > + struct ufs_hba *hba = platform_get_drvdata(pdev); > > > + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); > > > + > > > + pm_runtime_forbid(&pdev->dev); > > > + pm_runtime_get_noresume(&pdev->dev); > > > > Why do you need these? You are not incrementing the refcount in probe() and > > there is no auto PM involved. > > Oh, it was a leftover from former version I haven't noticed. Will > remove. > I've sent a series [1] that addresses the runtime PM issues. Could you please give it a try and give your tested-by maybe? - Mani [1] https://lore.kernel.org/linux-scsi/20241111-ufs_bug_fix-v1-0-45ad8b62f02e@linaro.org/
在 2024/11/12 14:43, Manivannan Sadhasivam 写道: > On Mon, Nov 11, 2024 at 09:10:39AM +0800, Shawn Lin wrote: > > [...] > >>>> +static void ufs_rockchip_remove(struct platform_device *pdev) >>>> +{ >>>> + struct ufs_hba *hba = platform_get_drvdata(pdev); >>>> + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); >>>> + >>>> + pm_runtime_forbid(&pdev->dev); >>>> + pm_runtime_get_noresume(&pdev->dev); >>> >>> Why do you need these? You are not incrementing the refcount in probe() and >>> there is no auto PM involved. >> >> Oh, it was a leftover from former version I haven't noticed. Will >> remove. >> > > I've sent a series [1] that addresses the runtime PM issues. Could you please > give it a try and give your tested-by maybe? Sure, I will give it a try, thanks. > > - Mani > > [1] https://lore.kernel.org/linux-scsi/20241111-ufs_bug_fix-v1-0-45ad8b62f02e@linaro.org/ >
diff --git a/drivers/ufs/host/Kconfig b/drivers/ufs/host/Kconfig index 580c8d0..191fbd7 100644 --- a/drivers/ufs/host/Kconfig +++ b/drivers/ufs/host/Kconfig @@ -142,3 +142,15 @@ config SCSI_UFS_SPRD Select this if you have UFS controller on Unisoc chipset. If unsure, say N. + +config SCSI_UFS_ROCKCHIP + tristate "Rockchip UFS host controller driver" + depends on SCSI_UFSHCD_PLATFORM && (ARCH_ROCKCHIP || COMPILE_TEST) + help + This selects the Rockchip specific additions to UFSHCD platform driver. + UFS host on Rockchip needs some vendor specific configuration before + accessing the hardware which includes PHY configuration and vendor + specific registers. + + Select this if you have UFS controller on Rockchip chipset. + If unsure, say N. diff --git a/drivers/ufs/host/Makefile b/drivers/ufs/host/Makefile index 4573aea..2f97feb 100644 --- a/drivers/ufs/host/Makefile +++ b/drivers/ufs/host/Makefile @@ -10,5 +10,6 @@ obj-$(CONFIG_SCSI_UFSHCD_PLATFORM) += ufshcd-pltfrm.o obj-$(CONFIG_SCSI_UFS_HISI) += ufs-hisi.o obj-$(CONFIG_SCSI_UFS_MEDIATEK) += ufs-mediatek.o obj-$(CONFIG_SCSI_UFS_RENESAS) += ufs-renesas.o +obj-$(CONFIG_SCSI_UFS_ROCKCHIP) += ufs-rockchip.o obj-$(CONFIG_SCSI_UFS_SPRD) += ufs-sprd.o obj-$(CONFIG_SCSI_UFS_TI_J721E) += ti-j721e-ufs.o diff --git a/drivers/ufs/host/ufs-rockchip.c b/drivers/ufs/host/ufs-rockchip.c new file mode 100644 index 0000000..9c277bc --- /dev/null +++ b/drivers/ufs/host/ufs-rockchip.c @@ -0,0 +1,340 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Rockchip UFS Host Controller driver + * + * Copyright (C) 2024 Rockchip Electronics Co.Ltd. + */ + +#include <linux/clk.h> +#include <linux/gpio.h> +#include <linux/mfd/syscon.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_domain.h> +#include <linux/pm_wakeup.h> +#include <linux/regmap.h> +#include <linux/reset.h> + +#include <ufs/ufshcd.h> +#include <ufs/unipro.h> +#include "ufshcd-pltfrm.h" +#include "ufs-rockchip.h" + +static int ufs_rockchip_hce_enable_notify(struct ufs_hba *hba, + enum ufs_notify_change_status status) +{ + int err = 0; + + if (status == POST_CHANGE) + err = ufshcd_vops_phy_initialization(hba); + + return err; +} + +static void ufs_rockchip_set_pm_lvl(struct ufs_hba *hba) +{ + hba->rpm_lvl = UFS_PM_LVL_5; + hba->spm_lvl = UFS_PM_LVL_5; +} + +static int ufs_rockchip_rk3576_phy_init(struct ufs_hba *hba) +{ + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); + + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(PA_LOCAL_TX_LCC_ENABLE, 0x0), 0x0); + /* enable the mphy DME_SET cfg */ + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x200, 0x0), 0x40); + for (int i = 0; i < 2; i++) { + /* Configuration M-TX */ + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xaa, SEL_TX_LANE0 + i), 0x06); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xa9, SEL_TX_LANE0 + i), 0x02); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xad, SEL_TX_LANE0 + i), 0x44); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xac, SEL_TX_LANE0 + i), 0xe6); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xab, SEL_TX_LANE0 + i), 0x07); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x94, SEL_TX_LANE0 + i), 0x93); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x93, SEL_TX_LANE0 + i), 0xc9); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x7f, SEL_TX_LANE0 + i), 0x00); + /* Configuration M-RX */ + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x12, SEL_RX_LANE0 + i), 0x06); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x11, SEL_RX_LANE0 + i), 0x00); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1d, SEL_RX_LANE0 + i), 0x58); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1c, SEL_RX_LANE0 + i), 0x8c); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x1b, SEL_RX_LANE0 + i), 0x02); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x25, SEL_RX_LANE0 + i), 0xf6); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x2f, SEL_RX_LANE0 + i), 0x69); + } + /* disable the mphy DME_SET cfg */ + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x200, 0x0), 0x00); + + ufs_sys_writel(host->mphy_base, 0x80, 0x08C); + ufs_sys_writel(host->mphy_base, 0xB5, 0x110); + ufs_sys_writel(host->mphy_base, 0xB5, 0x250); + + ufs_sys_writel(host->mphy_base, 0x03, 0x134); + ufs_sys_writel(host->mphy_base, 0x03, 0x274); + + ufs_sys_writel(host->mphy_base, 0x38, 0x0E0); + ufs_sys_writel(host->mphy_base, 0x38, 0x220); + + ufs_sys_writel(host->mphy_base, 0x50, 0x164); + ufs_sys_writel(host->mphy_base, 0x50, 0x2A4); + + ufs_sys_writel(host->mphy_base, 0x80, 0x178); + ufs_sys_writel(host->mphy_base, 0x80, 0x2B8); + + ufs_sys_writel(host->mphy_base, 0x18, 0x1B0); + ufs_sys_writel(host->mphy_base, 0x18, 0x2F0); + + ufs_sys_writel(host->mphy_base, 0x03, 0x128); + ufs_sys_writel(host->mphy_base, 0x03, 0x268); + + ufs_sys_writel(host->mphy_base, 0x20, 0x12C); + ufs_sys_writel(host->mphy_base, 0x20, 0x26C); + + ufs_sys_writel(host->mphy_base, 0xC0, 0x120); + ufs_sys_writel(host->mphy_base, 0xC0, 0x260); + + ufs_sys_writel(host->mphy_base, 0x03, 0x094); + + ufs_sys_writel(host->mphy_base, 0x03, 0x1B4); + ufs_sys_writel(host->mphy_base, 0x03, 0x2F4); + + ufs_sys_writel(host->mphy_base, 0xC0, 0x08C); + usleep_range(1, 2); + ufs_sys_writel(host->mphy_base, 0x00, 0x08C); + + usleep_range(200, 250); + /* start link up */ + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(MIB_T_DBG_CPORT_TX_ENDIAN, 0), 0x0); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(MIB_T_DBG_CPORT_RX_ENDIAN, 0), 0x0); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID, 0), 0x0); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID_VALID, 0), 0x1); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(T_PEERDEVICEID, 0), 0x1); + ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(T_CONNECTIONSTATE, 0), 0x1); + + return 0; +} + +static int ufs_rockchip_common_init(struct ufs_hba *hba) +{ + struct device *dev = hba->dev; + struct platform_device *pdev = to_platform_device(dev); + struct ufs_rockchip_host *host; + int err; + + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); + if (!host) + return -ENOMEM; + + /* system control register for hci */ + host->ufs_sys_ctrl = devm_platform_ioremap_resource_byname(pdev, "hci_grf"); + if (IS_ERR(host->ufs_sys_ctrl)) + return dev_err_probe(dev, PTR_ERR(host->ufs_sys_ctrl), + "cannot ioremap for hci system control register\n"); + + /* system control register for mphy */ + host->ufs_phy_ctrl = devm_platform_ioremap_resource_byname(pdev, "mphy_grf"); + if (IS_ERR(host->ufs_phy_ctrl)) + return dev_err_probe(dev, PTR_ERR(host->ufs_phy_ctrl), + "cannot ioremap for mphy system control register\n"); + + /* mphy base register */ + host->mphy_base = devm_platform_ioremap_resource_byname(pdev, "mphy"); + if (IS_ERR(host->mphy_base)) + return dev_err_probe(dev, PTR_ERR(host->mphy_base), + "cannot ioremap for mphy base register\n"); + + host->rst = devm_reset_control_array_get_exclusive(dev); + if (IS_ERR(host->rst)) + return dev_err_probe(dev, PTR_ERR(host->rst), + "failed to get reset control\n"); + + reset_control_assert(host->rst); + usleep_range(1, 2); + reset_control_deassert(host->rst); + + host->ref_out_clk = devm_clk_get_enabled(dev, "ref_out"); + if (IS_ERR(host->ref_out_clk)) + return dev_err_probe(dev, PTR_ERR(host->ref_out_clk), + "ref_out unavailable\n"); + + host->rst_gpio = devm_gpiod_get(&pdev->dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(host->rst_gpio)) + return dev_err_probe(&pdev->dev, PTR_ERR(host->rst_gpio), + "invalid reset-gpios property in node\n"); + + host->clks[0].id = "core"; + host->clks[1].id = "pclk"; + host->clks[2].id = "pclk_mphy"; + err = devm_clk_bulk_get_optional(dev, UFS_MAX_CLKS, host->clks); + if (err) + return dev_err_probe(dev, err, "failed to get clocks\n"); + + err = clk_bulk_prepare_enable(UFS_MAX_CLKS, host->clks); + if (err) + return dev_err_probe(dev, err, "failed to enable clocks\n"); + + host->hba = hba; + + ufshcd_set_variant(hba, host); + + return 0; +} + +static int ufs_rockchip_rk3576_init(struct ufs_hba *hba) +{ + struct device *dev = hba->dev; + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); + int ret; + + hba->quirks = UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING | + UFSHCI_QUIRK_DME_RESET_ENABLE_AFTER_HCE; + + /* Enable BKOPS when suspend */ + hba->caps |= UFSHCD_CAP_AUTO_BKOPS_SUSPEND; + /* Enable putting device into deep sleep */ + hba->caps |= UFSHCD_CAP_DEEPSLEEP; + /* Enable devfreq of UFS */ + hba->caps |= UFSHCD_CAP_CLK_SCALING; + /* Enable WriteBooster */ + hba->caps |= UFSHCD_CAP_WB_EN; + + host->pd_id = RK3576_PD_UFS; + + ret = ufs_rockchip_common_init(hba); + if (ret) + return dev_err_probe(dev, ret, "ufs common init fail\n"); + + return 0; +} + +static int ufs_rockchip_device_reset(struct ufs_hba *hba) +{ + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); + + /* Active the reset-gpios */ + gpiod_set_value_cansleep(host->rst_gpio, 1); + usleep_range(20, 25); + + /* Inactive the reset-gpios */ + gpiod_set_value_cansleep(host->rst_gpio, 0); + usleep_range(20, 25); + + return 0; +} + +static const struct ufs_hba_variant_ops ufs_hba_rk3576_vops = { + .name = "rk3576", + .init = ufs_rockchip_rk3576_init, + .device_reset = ufs_rockchip_device_reset, + .hce_enable_notify = ufs_rockchip_hce_enable_notify, + .phy_initialization = ufs_rockchip_rk3576_phy_init, +}; + +static const struct of_device_id ufs_rockchip_of_match[] = { + { .compatible = "rockchip,rk3576-ufshc", .data = &ufs_hba_rk3576_vops }, +}; +MODULE_DEVICE_TABLE(of, ufs_rockchip_of_match); + +static int ufs_rockchip_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + const struct ufs_hba_variant_ops *vops; + struct ufs_hba *hba; + int err; + + vops = device_get_match_data(dev); + if (!vops) + return dev_err_probe(dev, -EINVAL, "ufs_hba_variant_ops not defined.\n"); + + err = ufshcd_pltfrm_init(pdev, vops); + if (err) + return dev_err_probe(dev, err, "ufshcd_pltfrm_init failed\n"); + + hba = platform_get_drvdata(pdev); + /* Set the default desired pm level in case no users set via sysfs */ + ufs_rockchip_set_pm_lvl(hba); + + return 0; +} + +static void ufs_rockchip_remove(struct platform_device *pdev) +{ + struct ufs_hba *hba = platform_get_drvdata(pdev); + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); + + pm_runtime_forbid(&pdev->dev); + pm_runtime_get_noresume(&pdev->dev); + ufshcd_remove(hba); + ufshcd_dealloc_host(hba); + clk_bulk_disable_unprepare(UFS_MAX_CLKS, host->clks); +} + +#ifdef CONFIG_PM +static int ufs_rockchip_runtime_suspend(struct device *dev) +{ + struct ufs_hba *hba = dev_get_drvdata(dev); + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); + + clk_disable_unprepare(host->ref_out_clk); + + /* Shouldn't power down if rpm_lvl is less than level 5. */ + dev_pm_genpd_rpm_always_on(dev, hba->rpm_lvl < UFS_PM_LVL_5 ? true : false); + + return ufshcd_runtime_suspend(dev); +} + +static int ufs_rockchip_runtime_resume(struct device *dev) +{ + struct ufs_hba *hba = dev_get_drvdata(dev); + struct ufs_rockchip_host *host = ufshcd_get_variant(hba); + int err; + + err = clk_prepare_enable(host->ref_out_clk); + if (err) { + dev_err(hba->dev, "failed to enable ref out clock %d\n", err); + return err; + } + + reset_control_assert(host->rst); + usleep_range(1, 2); + reset_control_deassert(host->rst); + + return ufshcd_runtime_resume(dev); +} +#endif + +#ifdef CONFIG_PM_SLEEP +static int ufs_rockchip_system_suspend(struct device *dev) +{ + struct ufs_hba *hba = dev_get_drvdata(dev); + + if (hba->spm_lvl < 5) + device_set_wakeup_path(dev); + else + device_clr_wakeup_path(dev); + + return ufshcd_system_suspend(dev); +} +#endif + +static const struct dev_pm_ops ufs_rockchip_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(ufs_rockchip_system_suspend, ufshcd_system_resume) + SET_RUNTIME_PM_OPS(ufs_rockchip_runtime_suspend, ufs_rockchip_runtime_resume, NULL) + .prepare = ufshcd_suspend_prepare, + .complete = ufshcd_resume_complete, +}; + +static struct platform_driver ufs_rockchip_pltform = { + .probe = ufs_rockchip_probe, + .remove = ufs_rockchip_remove, + .driver = { + .name = "ufshcd-rockchip", + .pm = &ufs_rockchip_pm_ops, + .of_match_table = ufs_rockchip_of_match, + }, +}; +module_platform_driver(ufs_rockchip_pltform); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Rockchip UFS Host Driver"); diff --git a/drivers/ufs/host/ufs-rockchip.h b/drivers/ufs/host/ufs-rockchip.h new file mode 100644 index 0000000..37c45a5 --- /dev/null +++ b/drivers/ufs/host/ufs-rockchip.h @@ -0,0 +1,51 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Rockchip UFS Host Controller driver + * + * Copyright (C) 2024 Rockchip Electronics Co.Ltd. + */ + +#ifndef _UFS_ROCKCHIP_H_ +#define _UFS_ROCKCHIP_H_ + +#define UFS_MAX_CLKS 3 + +#define SEL_TX_LANE0 0x0 +#define SEL_TX_LANE1 0x1 +#define SEL_TX_LANE2 0x2 +#define SEL_TX_LANE3 0x3 +#define SEL_RX_LANE0 0x4 +#define SEL_RX_LANE1 0x5 +#define SEL_RX_LANE2 0x6 +#define SEL_RX_LANE3 0x7 + +#define MIB_T_DBG_CPORT_TX_ENDIAN 0xc022 +#define MIB_T_DBG_CPORT_RX_ENDIAN 0xc023 + +#define RK3576_PD_UFS 0x7 + +struct ufs_rockchip_host { + struct ufs_hba *hba; + void __iomem *ufs_phy_ctrl; + void __iomem *ufs_sys_ctrl; + void __iomem *mphy_base; + struct gpio_desc *rst_gpio; + struct reset_control *rst; + struct clk *ref_out_clk; + struct clk_bulk_data clks[UFS_MAX_CLKS]; + uint64_t caps; + uint64_t pd_id; +}; + +#define ufs_sys_writel(base, val, reg) \ + writel((val), (base) + (reg)) +#define ufs_sys_readl(base, reg) readl((base) + (reg)) +#define ufs_sys_set_bits(base, mask, reg) \ + ufs_sys_writel( \ + (base), ((mask) | (ufs_sys_readl((base), (reg)))), (reg)) +#define ufs_sys_ctrl_clr_bits(base, mask, reg) \ + ufs_sys_writel((base), \ + ((~(mask)) & (ufs_sys_readl((base), (reg)))), \ + (reg)) + +#endif /* _UFS_ROCKCHIP_H_ */
RK3576 SoC contains a UFS controller, add initial support for it. The features are: (1) support UFS 2.0 features (2) High speed up to HS-G3 (3) 2RX-2TX lanes (4) auto H8 entry and exit Software limitation: (1) HCE procedure: enable controller->enable intr->dme_reset->dme_enable (2) disable unipro timeout values before power mode change Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> --- Changes in v4: - deal with power domain of rpm and spm suggested by Ulf - Fix typo and disable clks in ufs_rockchip_remove - remove clk_disable_unprepare(host->ref_out_clk) from ufs_rockchip_remove Changes in v3: - reword Kconfig description - elaborate more about controller in commit msg - use rockchip,rk3576-ufshc for compatible - remove useless header file - remove inline for ufshcd_is_device_present - use usleep_range instead - remove initialization, reverse Xmas order - remove useless varibles - check vops for null - other small fixes for err path - remove pm_runtime_set_active - fix the active and inactive reset-gpios logic - fix rpm_lvl and spm_lvl to 5 and move to end of probe path - remove unnecessary system PM callbacks - use UFSHCI_QUIRK_DME_RESET_ENABLE_AFTER_HCE instead of UFSHCI_QUIRK_BROKEN_HCE Changes in v2: None drivers/ufs/host/Kconfig | 12 ++ drivers/ufs/host/Makefile | 1 + drivers/ufs/host/ufs-rockchip.c | 340 ++++++++++++++++++++++++++++++++++++++++ drivers/ufs/host/ufs-rockchip.h | 51 ++++++ 4 files changed, 404 insertions(+) create mode 100644 drivers/ufs/host/ufs-rockchip.c create mode 100644 drivers/ufs/host/ufs-rockchip.h