@@ -59,6 +59,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-magneton-sku393216.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-magneton-sku393217.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-magneton-sku393218.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-rusty-sku196608.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-starmie-sku0.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-starmie-sku1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-steelix-sku131072.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-steelix-sku131073.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
new file mode 100644
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8186-corsola-starmie.dtsi"
+
+/ {
+ model = "Google Starmie sku0 board";
+ compatible = "google,starmie-sku0", "google,starmie-sku2",
+ "google,starmie-sku3", "google,starmie",
+ "mediatek,mt8186";
+};
+
+&panel {
+ compatible = "starry,ili9882t";
+};
+
+&i2c1 {
+ touchscreen: touchscreen@41 {
+ compatible = "ilitek,ili9882t";
+ reg = <0x41>;
+ interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_pins>;
+ panel = <&panel>;
+ reset-gpios = <&pio 60 GPIO_ACTIVE_LOW>;
+ vccio-supply = <&mt6366_vio18_reg>;
+ };
+};
new file mode 100644
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8186-corsola-starmie.dtsi"
+
+/ {
+ model = "Google Starmie sku1 board";
+ compatible = "google,starmie-sku1", "google,starmie-sku4",
+ "google,starmie", "mediatek,mt8186";
+};
+
+&panel {
+ compatible = "starry,himax83102-j02";
+};
+
+&i2c1 {
+ touchscreen_himax: touchscreen@4f {
+ compatible = "hid-over-i2c";
+ reg = <0x4f>;
+ interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_pins>;
+ vdd-supply = <&mt6366_vio18_reg>;
+ panel = <&panel>;
+ post-power-on-delay-ms = <450>;
+ hid-descr-addr = <0x0001>;
+ };
+};
new file mode 100644
@@ -0,0 +1,465 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8186-corsola.dtsi"
+
+/ {
+ en_pp6000_mipi_disp_150ma: en-pp6000-mipi-disp-150ma {
+ compatible = "regulator-fixed";
+ regulator-name = "en_pp6000_mipi_disp_150ma";
+ gpio = <&pio 154 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&en_pp6000_mipi_disp_150ma_fixed_pins>;
+ };
+
+ /*
+ * Starmie does not have 3.3V display regulator. It is replaced
+ * with 6V module for enabling panel, re-using eDP GPIOs.
+ */
+ /delete-node/ pp3300_disp_x;
+ en_pp6000_mipi_disp: en-regulator-pp6000-mipi-disp {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_panel_fixed_pins>;
+ gpios = <&pio 153 GPIO_ACTIVE_HIGH>;
+ regulator-name = "en_pp6000_mipi_disp";
+ enable-active-high;
+ regulator-enable-ramp-delay = <3000>;
+ vin-supply = <&pp3300_z2>;
+ };
+
+ tboard_thermistor1: thermal-sensor1 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&auxadc 0>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-5000) 1492
+ 0 1413
+ 5000 1324
+ 10000 1227
+ 15000 1121
+ 20000 1017
+ 25000 900
+ 30000 797
+ 35000 698
+ 40000 606
+ 45000 522
+ 50000 449
+ 55000 383
+ 60000 327
+ 65000 278
+ 70000 236
+ 75000 201
+ 80000 171
+ 85000 145
+ 90000 163
+ 95000 124
+ 100000 91
+ 105000 78
+ 110000 67
+ 115000 58
+ 120000 50
+ 125000 44>;
+ };
+
+ tboard_thermistor2: thermal-sensor2 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&auxadc 1>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-5000) 1492
+ 0 1413
+ 5000 1324
+ 10000 1227
+ 15000 1121
+ 20000 1017
+ 25000 900
+ 30000 797
+ 35000 698
+ 40000 606
+ 45000 522
+ 50000 449
+ 55000 383
+ 60000 327
+ 65000 278
+ 70000 236
+ 75000 201
+ 80000 171
+ 85000 145
+ 90000 163
+ 95000 124
+ 100000 91
+ 105000 78
+ 110000 67
+ 115000 58
+ 120000 50
+ 125000 44>;
+ };
+};
+
+/*
+ * Starmie does not have EC keyboard. Remove default keyboard controller
+ * and replace it with the driver for side switches.
+ */
+/delete-node/ &keyboard_controller;
+
+&cros_ec {
+ cbas: cbas {
+ compatible = "google,cros-cbas";
+ };
+
+ keyboard-controller {
+ compatible = "google,cros-ec-keyb-switches";
+ };
+};
+
+&dsi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel: panel@0 {
+ /* compatible will be set in board dts */
+ reg = <0>;
+ enable-gpios = <&pio 98 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_pins_default>;
+ avdd-supply = <&en_pp6000_mipi_disp>;
+ avee-supply = <&en_pp6000_mipi_disp_150ma>;
+ pp1800-supply = <&mt6366_vio18_reg>;
+ backlight = <&backlight_lcd0>;
+ rotation = <270>;
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
+&dsi_out {
+ remote-endpoint = <&panel_in>;
+};
+
+&i2c0 {
+ status = "disabled";
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c4 {
+ status = "disabled";
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+};
+
+&mmc1_pins_default {
+ pins-clk {
+ drive-strength = <8>;
+ };
+
+ pins-cmd-dat {
+ drive-strength = <8>;
+ };
+};
+
+&mmc1_pins_uhs {
+ pins-clk {
+ drive-strength = <8>;
+ };
+
+ pins-cmd-dat {
+ drive-strength = <8>;
+ };
+};
+
+&pen_insert {
+ wakeup-event-action = <EV_ACT_ANY>;
+};
+
+&pio {
+ /* 185 lines */
+ gpio-line-names = "TP",
+ "TP",
+ "TP",
+ "I2S0_HP_DI",
+ "I2S3_DP_SPKR_DO",
+ "SAR_INT_ODL",
+ "BT_WAKE_AP_ODL",
+ "WIFI_INT_ODL",
+ "DPBRDG_INT_ODL",
+ "NC",
+ "EC_AP_HPD_OD",
+ "NC",
+ "TCHSCR_INT_1V8_ODL",
+ "EC_AP_INT_ODL",
+ "EC_IN_RW_ODL",
+ "GSC_AP_INT_ODL",
+ /*
+ * AP_FLASH_WP_L is crossystem ABI. Rev1 schematics
+ * call it AP_WP_ODL.
+ */
+ "AP_FLASH_WP_L",
+ "HP_INT_ODL",
+ "PEN_EJECT_OD",
+ "NC",
+ "NC",
+ "UCAM_SEN_EN",
+ "NC",
+ "NC",
+ "NC",
+ "I2S2_DP_SPK_MCK",
+ "I2S2_DP_SPKR_BCK",
+ "I2S2_DP_SPKR_LRCK",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "UART_GSC_TX_AP_RX",
+ "UART_AP_TX_GSC_RX",
+ "UART_DBGCON_TX_ADSP_RX",
+ "UART_ADSP_TX_DBGCON_RX",
+ "NC",
+ "TCHSCR_REPORT_DISABLE",
+ "NC",
+ "EN_PP1800_DPBRDG",
+ "SPI_AP_CLK_EC",
+ "SPI_AP_CS_EC_L",
+ "SPI_AP_DO_EC_DI",
+ "SPI_AP_DI_EC_DO",
+ "SPI_AP_CLK_GSC",
+ "SPI_AP_CS_GSC_L",
+ "SPI_AP_DO_GSC_DI",
+ "SPI_AP_DI_GSC_DO",
+ "UART_DBGCON_TX_SCP_RX",
+ "UART_SCP_TX_DBGCON_RX",
+ "EN_PP1200_CAM_X",
+ "WLAN_MODULE_RST_L",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "I2S1_HP_DO",
+ "I2S1_HP_BCK",
+ "I2S1_HP_LRCK",
+ "I2S1_HP_MCK",
+ "TCHSCR_RST_1V8_L",
+ "SPI_AP_CLK_ROM",
+ "SPI_AP_CS_ROM_L",
+ "SPI_AP_DO_ROM_DI",
+ "SPI_AP_DI_ROM_DO",
+ "NC",
+ "NC",
+ "EMMC_STRB",
+ "EMMC_CLK",
+ "EMMC_CMD",
+ "EMMC_RST_L",
+ "EMMC_DATA0",
+ "EMMC_DATA1",
+ "EMMC_DATA2",
+ "EMMC_DATA3",
+ "EMMC_DATA4",
+ "EMMC_DATA5",
+ "EMMC_DATA6",
+ "EMMC_DATA7",
+ "AP_KPCOL0",
+ "NC",
+ "NC",
+ "NC",
+ "TP",
+ "SDIO_CLK",
+ "SDIO_CMD",
+ "SDIO_DATA0",
+ "SDIO_DATA1",
+ "SDIO_DATA2",
+ "SDIO_DATA3",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "MIPI_BL_PWM_1V8",
+ "DISP_RST_1V8_L",
+ "MIPI_DPI_CLK",
+ "MIPI_DPI_VSYNC",
+ "MIPI_DPI_HSYNC",
+ "MIPI_DPI_DE",
+ "MIPI_DPI_D0",
+ "MIPI_DPI_D1",
+ "MIPI_DPI_D2",
+ "MIPI_DPI_D3",
+ "MIPI_DPI_D4",
+ "MIPI_DPI_D5",
+ "MIPI_DPI_D6",
+ "MIPI_DPI_DA7",
+ "MIPI_DPI_D8",
+ "MIPI_DPI_D9",
+ "MIPI_DPI_D10",
+ "MIPI_DPI_D11",
+ "PCM_BT_CLK",
+ "PCM_BT_SYNC",
+ "PCM_BT_DI",
+ "PCM_BT_DO",
+ "JTAG_TMS_TP",
+ "JTAG_TCK_TP",
+ "JTAG_TDI_TP",
+ "JTAG_TDO_TP",
+ "JTAG_TRSTN_TP",
+ "NC",
+ "NC",
+ "UCAM_DET_ODL",
+ "NC",
+ "NC",
+ "AP_I2C_TCHSCR_SCL_1V8",
+ "AP_I2C_TCHSCR_SDA_1V8",
+ "NC",
+ "NC",
+ "AP_I2C_DPBRDG_SCL_1V8",
+ "AP_I2C_DPBRDG_SDA_1V8",
+ "NC",
+ "NC",
+ "AP_I2C_AUD_SCL_1V8",
+ "AP_I2C_AUD_SDA_1V8",
+ "AP_I2C_DISP_SCL_1V8",
+ "AP_I2C_DISP_SDA_1V8",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "SCP_I2C_SENSOR_SCL_1V8",
+ "SCP_I2C_SENSOR_SDA_1V8",
+ "AP_EC_WARM_RST_REQ",
+ "AP_XHCI_INIT_DONE",
+ "USB3_HUB_RST_L",
+ "EN_SPKR",
+ "BEEP_ON",
+ "AP_DISP_BKLTEN",
+ "EN_PP6000_MIPI_DISP",
+ "EN_PP6000_MIPI_DISP_150MA",
+ "BT_KILL_1V8_L",
+ "WIFI_KILL_1V8_L",
+ "PWRAP_SPI0_CSN",
+ "PWRAP_SPI0_CK",
+ "PWRAP_SPI0_MO",
+ "PWRAP_SPI0_MI",
+ "SRCLKENA0",
+ "SRCLKENA1",
+ "SCP_VREQ_VAO",
+ "AP_RTC_CLK32K",
+ "AP_PMIC_WDTRST_L",
+ "AUD_CLK_MOSI",
+ "AUD_SYNC_MOSI",
+ "AUD_DAT_MOSI0",
+ "AUD_DAT_MOSI1",
+ "AUD_CLK_MISO",
+ "AUD_SYNC_MISO",
+ "AUD_DAT_MISO0",
+ "AUD_DAT_MISO1",
+ "NC",
+ "NC",
+ "NC",
+ "DPBRDG_RST_L",
+ "LTE_W_DISABLE_L",
+ "LTE_SAR_DETECT_L",
+ "EN_PP3300_LTE_X",
+ "LTE_PWR_OFF_L",
+ "LTE_RESET_L",
+ "TP",
+ "TP";
+
+ dpi_pin_default: dpi-pin-default {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO103__FUNC_GPIO103>,
+ <PINMUX_GPIO104__FUNC_GPIO104>,
+ <PINMUX_GPIO105__FUNC_GPIO105>,
+ <PINMUX_GPIO106__FUNC_GPIO106>,
+ <PINMUX_GPIO107__FUNC_GPIO107>,
+ <PINMUX_GPIO108__FUNC_GPIO108>,
+ <PINMUX_GPIO109__FUNC_GPIO109>,
+ <PINMUX_GPIO110__FUNC_GPIO110>,
+ <PINMUX_GPIO111__FUNC_GPIO111>,
+ <PINMUX_GPIO112__FUNC_GPIO112>,
+ <PINMUX_GPIO113__FUNC_GPIO113>,
+ <PINMUX_GPIO114__FUNC_GPIO114>,
+ <PINMUX_GPIO101__FUNC_GPIO101>,
+ <PINMUX_GPIO100__FUNC_GPIO100>,
+ <PINMUX_GPIO102__FUNC_GPIO102>,
+ <PINMUX_GPIO99__FUNC_GPIO99>;
+ drive-strength = <10>;
+ output-low;
+ };
+ };
+
+ dpi_pin_func: dpi-pin-func {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO103__FUNC_DPI_DATA0>,
+ <PINMUX_GPIO104__FUNC_DPI_DATA1>,
+ <PINMUX_GPIO105__FUNC_DPI_DATA2>,
+ <PINMUX_GPIO106__FUNC_DPI_DATA3>,
+ <PINMUX_GPIO107__FUNC_DPI_DATA4>,
+ <PINMUX_GPIO108__FUNC_DPI_DATA5>,
+ <PINMUX_GPIO109__FUNC_DPI_DATA6>,
+ <PINMUX_GPIO110__FUNC_DPI_DATA7>,
+ <PINMUX_GPIO111__FUNC_DPI_DATA8>,
+ <PINMUX_GPIO112__FUNC_DPI_DATA9>,
+ <PINMUX_GPIO113__FUNC_DPI_DATA10>,
+ <PINMUX_GPIO114__FUNC_DPI_DATA11>,
+ <PINMUX_GPIO101__FUNC_DPI_HSYNC>,
+ <PINMUX_GPIO100__FUNC_DPI_VSYNC>,
+ <PINMUX_GPIO102__FUNC_DPI_DE>,
+ <PINMUX_GPIO99__FUNC_DPI_PCLK>;
+ drive-strength = <10>;
+ };
+ };
+
+ en_pp6000_mipi_disp_150ma_fixed_pins: en_pp6000-mipi-disp-150ma-fixed-pins {
+ pins-en {
+ pinmux = <PINMUX_GPIO154__FUNC_GPIO154>;
+ output-low;
+ };
+ };
+
+ panel_pins_default: panel-pins-default {
+ pins-en {
+ pinmux = <PINMUX_GPIO98__FUNC_GPIO98>;
+ output-low;
+ };
+ };
+};
+
+&usb_c1 {
+ status = "disabled";
+};
+
+&thermal_zones {
+ tboard1 {
+ polling-delay = <1000>; /* milliseconds */
+ polling-delay-passive = <0>; /* milliseconds */
+ thermal-sensors = <&tboard_thermistor1>;
+ };
+
+ tboard2 {
+ polling-delay = <1000>; /* milliseconds */
+ polling-delay-passive = <0>; /* milliseconds */
+ thermal-sensors = <&tboard_thermistor2>;
+ };
+};
+
+&wifi_pwrseq {
+ reset-gpios = <&pio 51 1>;
+};
+
+/*
+ * Battery on Starmie is using a different address than default.
+ */
+&battery {
+ reg = <0xf>;
+};
Add support for Starmie Chromebooks. Signed-off-by: Wojciech Macek <wmacek@chromium.org> --- Changelog v3-v2: - Cleaned up DTS - Re-using dsi_out node - Removed unnecessary delete-nodes - Moved touchpads to per-board dts - Modified 3.3/6V power regulator node Changelog v2-v1: - No changes arch/arm64/boot/dts/mediatek/Makefile | 2 + .../mediatek/mt8186-corsola-starmie-sku0.dts | 31 ++ .../mediatek/mt8186-corsola-starmie-sku1.dts | 31 ++ .../dts/mediatek/mt8186-corsola-starmie.dtsi | 465 ++++++++++++++++++ 4 files changed, 529 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-starmie-sku0.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-starmie-sku1.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-starmie.dtsi