@@ -132,6 +132,16 @@
#define REG_IRQ_STAT_CHA_SOT_BIT_ERR BIT(2)
#define REG_IRQ_STAT_CHA_PLL_UNLOCK BIT(0)
+enum sn65dsi83_channel {
+ CHANNEL_A,
+ CHANNEL_B
+};
+
+enum sn65dsi83_lvds_term {
+ OHM_100,
+ OHM_200
+};
+
enum sn65dsi83_model {
MODEL_SN65DSI83,
MODEL_SN65DSI84,
@@ -147,6 +157,8 @@ struct sn65dsi83 {
struct regulator *vcc;
bool lvds_dual_link;
bool lvds_dual_link_even_odd_swap;
+ int lvds_vod_swing_conf[2];
+ int lvds_term_conf[2];
};
static const struct regmap_range sn65dsi83_readable_ranges[] = {
@@ -237,6 +249,36 @@ static const struct regmap_config sn65dsi83_regmap_config = {
.max_register = REG_IRQ_STAT,
};
+static const int lvds_vod_swing_data_table[2][4][2] = {
+ { /* 100 Ohm */
+ { 180000, 313000 },
+ { 215000, 372000 },
+ { 250000, 430000 },
+ { 290000, 488000 },
+ },
+ { /* 200 Ohm */
+ { 150000, 261000 },
+ { 200000, 346000 },
+ { 250000, 428000 },
+ { 300000, 511000 },
+ },
+};
+
+static const int lvds_vod_swing_clock_table[2][4][2] = {
+ { /* 100 Ohm */
+ { 140000, 244000 },
+ { 168000, 290000 },
+ { 195000, 335000 },
+ { 226000, 381000 },
+ },
+ { /* 200 Ohm */
+ { 117000, 204000 },
+ { 156000, 270000 },
+ { 195000, 334000 },
+ { 234000, 399000 },
+ },
+};
+
static struct sn65dsi83 *bridge_to_sn65dsi83(struct drm_bridge *bridge)
{
return container_of(bridge, struct sn65dsi83, bridge);
@@ -435,12 +477,16 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
val |= REG_LVDS_FMT_LVDS_LINK_CFG;
regmap_write(ctx->regmap, REG_LVDS_FMT, val);
- regmap_write(ctx->regmap, REG_LVDS_VCOM, 0x05);
+ regmap_write(ctx->regmap, REG_LVDS_VCOM,
+ REG_LVDS_VCOM_CHA_LVDS_VOD_SWING(ctx->lvds_vod_swing_conf[CHANNEL_A]) |
+ REG_LVDS_VCOM_CHB_LVDS_VOD_SWING(ctx->lvds_vod_swing_conf[CHANNEL_B]));
regmap_write(ctx->regmap, REG_LVDS_LANE,
(ctx->lvds_dual_link_even_odd_swap ?
REG_LVDS_LANE_EVEN_ODD_SWAP : 0) |
- REG_LVDS_LANE_CHA_LVDS_TERM |
- REG_LVDS_LANE_CHB_LVDS_TERM);
+ (ctx->lvds_term_conf[CHANNEL_A] ?
+ REG_LVDS_LANE_CHA_LVDS_TERM : 0) |
+ (ctx->lvds_term_conf[CHANNEL_B] ?
+ REG_LVDS_LANE_CHB_LVDS_TERM : 0));
regmap_write(ctx->regmap, REG_LVDS_CM, 0x00);
le16val = cpu_to_le16(mode->hdisplay);
@@ -576,10 +622,101 @@ static const struct drm_bridge_funcs sn65dsi83_funcs = {
.atomic_get_input_bus_fmts = sn65dsi83_atomic_get_input_bus_fmts,
};
+static int sn65dsi83_select_lvds_vod_swing(struct device *dev,
+ u32 lvds_vod_swing_data[2], u32 lvds_vod_swing_clk[2], u8 lvds_term)
+{
+ int i;
+
+ for (i = 0; i <= 3; i++) {
+ if (lvds_vod_swing_data_table[lvds_term][i][0] >= lvds_vod_swing_data[0] &&
+ lvds_vod_swing_data_table[lvds_term][i][1] <= lvds_vod_swing_data[1] &&
+ lvds_vod_swing_clock_table[lvds_term][i][0] >= lvds_vod_swing_clk[0] &&
+ lvds_vod_swing_clock_table[lvds_term][i][1] <= lvds_vod_swing_clk[1])
+ return i;
+ }
+
+ dev_err(dev, "failed to find appropriate LVDS_VOD_SWING configuration\n");
+ return -EINVAL;
+}
+
+static int sn65dsi83_parse_lvds_endpoint(struct sn65dsi83 *ctx, int channel)
+{
+ struct device *dev = ctx->dev;
+ struct device_node *endpoint;
+ int endpoint_reg;
+ /* Set so the property can be freely selected if not defined */
+ u32 lvds_vod_swing_data[2] = { 0, 1000000 };
+ u32 lvds_vod_swing_clk[2] = { 0, 1000000 };
+ /* Set default near end terminataion to 200 Ohm */
+ u32 lvds_term = 200;
+ int lvds_vod_swing_conf;
+ int ret = 0;
+ int ret_data;
+ int ret_clock;
+
+ if (channel == CHANNEL_A)
+ endpoint_reg = 2;
+ else
+ endpoint_reg = 3;
+
+ endpoint = of_graph_get_endpoint_by_regs(dev->of_node, endpoint_reg, -1);
+
+ of_property_read_u32(endpoint, "ti,lvds-termination-ohms", &lvds_term);
+ if (lvds_term == 100)
+ ctx->lvds_term_conf[channel] = OHM_100;
+ else if (lvds_term == 200)
+ ctx->lvds_term_conf[channel] = OHM_200;
+ else
+ return -EINVAL;
+
+ ret_data = of_property_read_u32_array(endpoint, "ti,lvds-vod-swing-data-microvolt",
+ lvds_vod_swing_data, ARRAY_SIZE(lvds_vod_swing_data));
+ if (ret_data != 0 && ret_data != -EINVAL) {
+ ret = ret_data;
+ goto exit;
+ }
+
+ ret_clock = of_property_read_u32_array(endpoint, "ti,lvds-vod-swing-clock-microvolt",
+ lvds_vod_swing_clk, ARRAY_SIZE(lvds_vod_swing_clk));
+ if (ret_clock != 0 && ret_clock != -EINVAL) {
+ ret = ret_clock;
+ goto exit;
+ }
+
+ /* Use default value if both properties are NOT defined. */
+ if (ret_data == -EINVAL && ret_clock == -EINVAL)
+ lvds_vod_swing_conf = 0x1;
+
+ /* Use lookup table if any of the two properties is defined. */
+ if (!ret_data || !ret_clock) {
+ lvds_vod_swing_conf = sn65dsi83_select_lvds_vod_swing(dev, lvds_vod_swing_data,
+ lvds_vod_swing_clk, ctx->lvds_term_conf[channel]);
+ if (lvds_vod_swing_conf < 0) {
+ ret = lvds_vod_swing_conf;
+ goto exit;
+ }
+ }
+
+ ctx->lvds_vod_swing_conf[channel] = lvds_vod_swing_conf;
+ ret = 0;
+exit:
+ of_node_put(endpoint);
+ return ret;
+}
+
static int sn65dsi83_parse_dt(struct sn65dsi83 *ctx, enum sn65dsi83_model model)
{
struct drm_bridge *panel_bridge;
struct device *dev = ctx->dev;
+ int ret;
+
+ ret = sn65dsi83_parse_lvds_endpoint(ctx, CHANNEL_A);
+ if (ret < 0)
+ return ret;
+
+ ret = sn65dsi83_parse_lvds_endpoint(ctx, CHANNEL_B);
+ if (ret < 0)
+ return ret;
ctx->lvds_dual_link = false;
ctx->lvds_dual_link_even_odd_swap = false;
Add a optional properties to change LVDS output voltage. This should not be static as this depends mainly on the connected display voltage requirement. We have three properties: - "ti,lvds-termination-ohms", which sets near end termination, - "ti,lvds-vod-swing-data-microvolt" and - "ti,lvds-vod-swing-clock-microvolt" which both set LVDS differential output voltage for data and clock lanes. They are defined as an array with min and max values. The appropriate bitfield will be set if selected constraints can be met. If "ti,lvds-termination-ohms" is not defined the default of 200 Ohm near end termination will be used. Selecting only one: "ti,lvds-vod-swing-data-microvolt" or "ti,lvds-vod-swing-clock-microvolt" can be done, but the output voltage constraint for only data/clock lanes will be met. Setting both is recommended. Signed-off-by: Andrej Picej <andrej.picej@norik.com> --- Changes in v6: - rework termination resistor logic, default is now set by resistor value, not reg value, - move setting lvds_vod_swing_conf to default value of 0x1 inside if statement which checks if both properties are not set Changes in v5: - specify default values in sn65dsi83_parse_lvds_endpoint, - move sn65dsi83_parse_lvds_endpoint for channel B up, outside if, Changes in v4: - fix typo in commit message bitfiled -> bitfield - use arrays (lvds_vod_swing_conf and lvds_term_conf) in private data, instead of separate variables for channel A/B - add more checks on return value of "of_property_read_u32_array" Changes in v3: - use microvolts for default array values 1000 mV -> 1000000 uV. Changes in v2: - use datasheet tables to get the proper configuration - since major change was done change the authorship to myself --- drivers/gpu/drm/bridge/ti-sn65dsi83.c | 143 +++++++++++++++++++++++++- 1 file changed, 140 insertions(+), 3 deletions(-)