| Message ID | 20250301104749.36423-1-ziyao@disroot.org (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | Support SD/SDIO controllers on RK3528 | expand |
Hi, On 2025-03-01 11:47, Yao Zi wrote: > RK3528 features two SDIO controllers and one SD/MMC controller, describe > them in devicetree. Since their sample and drive clocks are located in > the VO and VPU GRFs, corresponding syscons are added to make these > clocks available. > > Signed-off-by: Yao Zi <ziyao@disroot.org> > --- > arch/arm64/boot/dts/rockchip/rk3528.dtsi | 62 ++++++++++++++++++++++++ > 1 file changed, 62 insertions(+) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi > index 5b334690356a..078c97fa1d9f 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi > +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi > @@ -7,6 +7,7 @@ > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/interrupt-controller/irq.h> > #include <dt-bindings/clock/rockchip,rk3528-cru.h> > +#include <dt-bindings/reset/rockchip,rk3528-cru.h> > > / { > compatible = "rockchip,rk3528"; > @@ -122,6 +123,16 @@ gic: interrupt-controller@fed01000 { > #interrupt-cells = <3>; > }; > > + vpu_grf: syscon@ff340000 { > + compatible = "rockchip,rk3528-vpu-grf", "syscon"; vpu_grf is also used for gmac1, so should possible be a "syscon", "simple-mfd", or have I misunderstood when to use simple-mfd ? > + reg = <0x0 0xff340000 0x0 0x8000>; > + }; > + > + vo_grf: syscon@ff360000 { > + compatible = "rockchip,rk3528-vo-grf", "syscon"; similar here, vo_grf is also used for gmac0. > + reg = <0x0 0xff360000 0x0 0x10000>; > + }; > + > cru: clock-controller@ff4a0000 { > compatible = "rockchip,rk3528-cru"; > reg = <0x0 0xff4a0000 0x0 0x30000>; > @@ -251,5 +262,56 @@ uart7: serial@ffa28000 { > reg-shift = <2>; > status = "disabled"; > }; > + > + sdio0: mmc@ffc10000 { > + compatible = "rockchip,rk3528-dw-mshc", > + "rockchip,rk3288-dw-mshc"; > + reg = <0x0 0xffc10000 0x0 0x4000>; > + clocks = <&cru HCLK_SDIO0>, > + <&cru CCLK_SRC_SDIO0>, > + <&cru SCLK_SDIO0_DRV>, > + <&cru SCLK_SDIO0_SAMPLE>; > + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; > + fifo-depth = <0x100>; > + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; > + max-frequency = <150000000>; > + resets = <&cru SRST_H_SDIO0>; > + reset-names = "reset"; > + status = "disabled"; > + }; > + > + sdio1: mmc@ffc20000 { > + compatible = "rockchip,rk3528-dw-mshc", > + "rockchip,rk3288-dw-mshc"; > + reg = <0x0 0xffc20000 0x0 0x4000>; > + clocks = <&cru HCLK_SDIO1>, > + <&cru CCLK_SRC_SDIO1>, > + <&cru SCLK_SDIO1_DRV>, > + <&cru SCLK_SDIO1_SAMPLE>; > + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; > + fifo-depth = <0x100>; > + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > + max-frequency = <150000000>; > + resets = <&cru SRST_H_SDIO1>; > + reset-names = "reset"; > + status = "disabled"; > + }; > + > + sdmmc: mmc@ffc30000 { > + compatible = "rockchip,rk3528-dw-mshc", > + "rockchip,rk3288-dw-mshc"; > + reg = <0x0 0xffc30000 0x0 0x4000>; > + clocks = <&cru HCLK_SDMMC0>, > + <&cru CCLK_SRC_SDMMC0>, > + <&cru SCLK_SDMMC_DRV>, > + <&cru SCLK_SDMMC_SAMPLE>; > + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; > + fifo-depth = <0x100>; > + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; > + max-frequency = <150000000>; > + resets = <&cru SRST_H_SDMMC0>; > + reset-names = "reset"; Suggest adding default pinctrl props here: pinctrl-names = "default"; pinctrl-0 = <&sdmmc_bus4>, <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_det>; And possible also for sdio0 and sdio1. Regards, Jonas > + status = "disabled"; > + }; > }; > };
Hey Joas, Am Samstag, 1. März 2025, 13:47:47 MEZ schrieb Jonas Karlman: > On 2025-03-01 11:47, Yao Zi wrote: > > RK3528 features two SDIO controllers and one SD/MMC controller, describe > > them in devicetree. Since their sample and drive clocks are located in > > the VO and VPU GRFs, corresponding syscons are added to make these > > clocks available. > > > > Signed-off-by: Yao Zi <ziyao@disroot.org> > > --- > > arch/arm64/boot/dts/rockchip/rk3528.dtsi | 62 ++++++++++++++++++++++++ > > 1 file changed, 62 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi > > index 5b334690356a..078c97fa1d9f 100644 > > --- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi > > +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi > > @@ -7,6 +7,7 @@ > > #include <dt-bindings/interrupt-controller/arm-gic.h> > > #include <dt-bindings/interrupt-controller/irq.h> > > #include <dt-bindings/clock/rockchip,rk3528-cru.h> > > +#include <dt-bindings/reset/rockchip,rk3528-cru.h> > > > > / { > > compatible = "rockchip,rk3528"; > > @@ -122,6 +123,16 @@ gic: interrupt-controller@fed01000 { > > #interrupt-cells = <3>; > > }; > > > > + vpu_grf: syscon@ff340000 { > > + compatible = "rockchip,rk3528-vpu-grf", "syscon"; > > vpu_grf is also used for gmac1, so should possible be a "syscon", > "simple-mfd", or have I misunderstood when to use simple-mfd ? simple-mfd is needed when the additional device is completely contained inside the particular syscon. For example, the usb2phy0 on rk3588 is completely living inside the usb2phy0-grf. Similarly the power-domains are living inside the rk3588 pmugrf. But the pmugrf also contains more stuff, so the power-domains are a subset of the pmugrf. Both of these above are a case for a simple-mfd. Similarly, gmac1 on rk3588 is ethernet@fe1c0000 , so a completely separate io-memory area, but references both the sysgrf as well as the php-grf as syscons for additional settings. So here the syscon does not need to be a simple-mfd. Hope that helps a bit Heiko
On Sat, Mar 01, 2025 at 01:47:47PM +0100, Jonas Karlman wrote: > Hi, > > On 2025-03-01 11:47, Yao Zi wrote: > > RK3528 features two SDIO controllers and one SD/MMC controller, describe > > them in devicetree. Since their sample and drive clocks are located in > > the VO and VPU GRFs, corresponding syscons are added to make these > > clocks available. > > > > Signed-off-by: Yao Zi <ziyao@disroot.org> > > --- > > arch/arm64/boot/dts/rockchip/rk3528.dtsi | 62 ++++++++++++++++++++++++ > > 1 file changed, 62 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi > > index 5b334690356a..078c97fa1d9f 100644 > > --- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi > > +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi > > @@ -7,6 +7,7 @@ > > #include <dt-bindings/interrupt-controller/arm-gic.h> > > #include <dt-bindings/interrupt-controller/irq.h> > > #include <dt-bindings/clock/rockchip,rk3528-cru.h> > > +#include <dt-bindings/reset/rockchip,rk3528-cru.h> > > > > / { > > compatible = "rockchip,rk3528"; > > @@ -122,6 +123,16 @@ gic: interrupt-controller@fed01000 { > > #interrupt-cells = <3>; > > }; > > > > + vpu_grf: syscon@ff340000 { > > + compatible = "rockchip,rk3528-vpu-grf", "syscon"; > > vpu_grf is also used for gmac1, so should possible be a "syscon", > "simple-mfd", or have I misunderstood when to use simple-mfd ? Just as Heiko explained, "simple-mfd" is only required when the child nodes should be populated automatically. Here these two GRFs are only referenced and have no child, thus "simple-mfd" compatible isn't useful. > > + reg = <0x0 0xff340000 0x0 0x8000>; > > + }; > > + > > + vo_grf: syscon@ff360000 { > > + compatible = "rockchip,rk3528-vo-grf", "syscon"; > > similar here, vo_grf is also used for gmac0. > > > + reg = <0x0 0xff360000 0x0 0x10000>; > > + }; > > + > > cru: clock-controller@ff4a0000 { > > compatible = "rockchip,rk3528-cru"; > > reg = <0x0 0xff4a0000 0x0 0x30000>; > > @@ -251,5 +262,56 @@ uart7: serial@ffa28000 { > > reg-shift = <2>; > > status = "disabled"; > > }; > > + > > + sdio0: mmc@ffc10000 { > > + compatible = "rockchip,rk3528-dw-mshc", > > + "rockchip,rk3288-dw-mshc"; > > + reg = <0x0 0xffc10000 0x0 0x4000>; > > + clocks = <&cru HCLK_SDIO0>, > > + <&cru CCLK_SRC_SDIO0>, > > + <&cru SCLK_SDIO0_DRV>, > > + <&cru SCLK_SDIO0_SAMPLE>; > > + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; > > + fifo-depth = <0x100>; > > + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; > > + max-frequency = <150000000>; > > + resets = <&cru SRST_H_SDIO0>; > > + reset-names = "reset"; > > + status = "disabled"; > > + }; > > + > > + sdio1: mmc@ffc20000 { > > + compatible = "rockchip,rk3528-dw-mshc", > > + "rockchip,rk3288-dw-mshc"; > > + reg = <0x0 0xffc20000 0x0 0x4000>; > > + clocks = <&cru HCLK_SDIO1>, > > + <&cru CCLK_SRC_SDIO1>, > > + <&cru SCLK_SDIO1_DRV>, > > + <&cru SCLK_SDIO1_SAMPLE>; > > + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; > > + fifo-depth = <0x100>; > > + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > > + max-frequency = <150000000>; > > + resets = <&cru SRST_H_SDIO1>; > > + reset-names = "reset"; > > + status = "disabled"; > > + }; > > + > > + sdmmc: mmc@ffc30000 { > > + compatible = "rockchip,rk3528-dw-mshc", > > + "rockchip,rk3288-dw-mshc"; > > + reg = <0x0 0xffc30000 0x0 0x4000>; > > + clocks = <&cru HCLK_SDMMC0>, > > + <&cru CCLK_SRC_SDMMC0>, > > + <&cru SCLK_SDMMC_DRV>, > > + <&cru SCLK_SDMMC_SAMPLE>; > > + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; > > + fifo-depth = <0x100>; > > + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; > > + max-frequency = <150000000>; > > + resets = <&cru SRST_H_SDMMC0>; > > + reset-names = "reset"; > > Suggest adding default pinctrl props here: > > pinctrl-names = "default"; > pinctrl-0 = <&sdmmc_bus4>, <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_det>; > > And possible also for sdio0 and sdio1. > > Regards, > Jonas It makes sense. As mentioned in the cover letter, I depended on the bootloader to setup pinctrl, to minimize dependency of the series. Will complete the pinctrl properties in next version. > > + status = "disabled"; > > + }; > > }; > > }; > Best regards, Yao Zi
diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi b/arch/arm64/boot/dts/rockchip/rk3528.dtsi index 5b334690356a..078c97fa1d9f 100644 --- a/arch/arm64/boot/dts/rockchip/rk3528.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/clock/rockchip,rk3528-cru.h> +#include <dt-bindings/reset/rockchip,rk3528-cru.h> / { compatible = "rockchip,rk3528"; @@ -122,6 +123,16 @@ gic: interrupt-controller@fed01000 { #interrupt-cells = <3>; }; + vpu_grf: syscon@ff340000 { + compatible = "rockchip,rk3528-vpu-grf", "syscon"; + reg = <0x0 0xff340000 0x0 0x8000>; + }; + + vo_grf: syscon@ff360000 { + compatible = "rockchip,rk3528-vo-grf", "syscon"; + reg = <0x0 0xff360000 0x0 0x10000>; + }; + cru: clock-controller@ff4a0000 { compatible = "rockchip,rk3528-cru"; reg = <0x0 0xff4a0000 0x0 0x30000>; @@ -251,5 +262,56 @@ uart7: serial@ffa28000 { reg-shift = <2>; status = "disabled"; }; + + sdio0: mmc@ffc10000 { + compatible = "rockchip,rk3528-dw-mshc", + "rockchip,rk3288-dw-mshc"; + reg = <0x0 0xffc10000 0x0 0x4000>; + clocks = <&cru HCLK_SDIO0>, + <&cru CCLK_SRC_SDIO0>, + <&cru SCLK_SDIO0_DRV>, + <&cru SCLK_SDIO0_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + fifo-depth = <0x100>; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; + max-frequency = <150000000>; + resets = <&cru SRST_H_SDIO0>; + reset-names = "reset"; + status = "disabled"; + }; + + sdio1: mmc@ffc20000 { + compatible = "rockchip,rk3528-dw-mshc", + "rockchip,rk3288-dw-mshc"; + reg = <0x0 0xffc20000 0x0 0x4000>; + clocks = <&cru HCLK_SDIO1>, + <&cru CCLK_SRC_SDIO1>, + <&cru SCLK_SDIO1_DRV>, + <&cru SCLK_SDIO1_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + fifo-depth = <0x100>; + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + max-frequency = <150000000>; + resets = <&cru SRST_H_SDIO1>; + reset-names = "reset"; + status = "disabled"; + }; + + sdmmc: mmc@ffc30000 { + compatible = "rockchip,rk3528-dw-mshc", + "rockchip,rk3288-dw-mshc"; + reg = <0x0 0xffc30000 0x0 0x4000>; + clocks = <&cru HCLK_SDMMC0>, + <&cru CCLK_SRC_SDMMC0>, + <&cru SCLK_SDMMC_DRV>, + <&cru SCLK_SDMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + fifo-depth = <0x100>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + max-frequency = <150000000>; + resets = <&cru SRST_H_SDMMC0>; + reset-names = "reset"; + status = "disabled"; + }; }; };
RK3528 features two SDIO controllers and one SD/MMC controller, describe them in devicetree. Since their sample and drive clocks are located in the VO and VPU GRFs, corresponding syscons are added to make these clocks available. Signed-off-by: Yao Zi <ziyao@disroot.org> --- arch/arm64/boot/dts/rockchip/rk3528.dtsi | 62 ++++++++++++++++++++++++ 1 file changed, 62 insertions(+)