new file mode 100644
@@ -0,0 +1,20 @@
+Broadcom BCM2835 I2C controller
+
+Required properties:
+- compatible : Should be "brcm,bcm2835-i2c".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks : The clock feeding the I2C controller.
+
+Recommended properties:
+- clock-frequency : desired I2C bus clock frequency in Hz.
+
+Example:
+
+i2c@20205000 {
+ compatible = "brcm,bcm2835-i2c";
+ reg = <0x7e205000 0x1000>;
+ interrupts = <2 21>;
+ clocks = <&clk_i2c>;
+ clock-frequency = <100000>;
+};
@@ -319,6 +319,18 @@ config I2C_AU1550
This driver can also be built as a module. If so, the module
will be called i2c-au1550.
+config I2C_BCM2835
+ tristate "Broadcom BCM2835 I2C controller"
+ depends on ARCH_BCM2835
+ help
+ If you say yes to this option, support will be included for the
+ BCM2835 I2C controller.
+
+ If you don't know what to do here, say N.
+
+ This support is also available as a module. If so, the module
+ will be called i2c-bcm2835.
+
config I2C_BLACKFIN_TWI
tristate "Blackfin TWI I2C support"
depends on BLACKFIN
@@ -30,6 +30,7 @@ obj-$(CONFIG_I2C_POWERMAC) += i2c-powermac.o
# Embedded system I2C/SMBus host controller drivers
obj-$(CONFIG_I2C_AT91) += i2c-at91.o
obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o
+obj-$(CONFIG_I2C_BCM2835) += i2c-bcm2835.o
obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o
obj-$(CONFIG_I2C_CBUS_GPIO) += i2c-cbus-gpio.o
obj-$(CONFIG_I2C_CPM) += i2c-cpm.o
new file mode 100644
@@ -0,0 +1,331 @@
+/*
+ * BCM2835 master mode driver
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define BCM2835_I2C_C 0x0
+#define BCM2835_I2C_S 0x4
+#define BCM2835_I2C_DLEN 0x8
+#define BCM2835_I2C_A 0xc
+#define BCM2835_I2C_FIFO 0x10
+#define BCM2835_I2C_DIV 0x14
+#define BCM2835_I2C_DEL 0x18
+#define BCM2835_I2C_CLKT 0x1c
+
+#define BCM2835_I2C_C_READ BIT(0)
+#define BCM2835_I2C_C_CLEAR BIT(4) /* bits 4 and 5 both clear */
+#define BCM2835_I2C_C_ST BIT(7)
+#define BCM2835_I2C_C_INTD BIT(8)
+#define BCM2835_I2C_C_INTT BIT(9)
+#define BCM2835_I2C_C_INTR BIT(10)
+#define BCM2835_I2C_C_I2CEN BIT(15)
+
+#define BCM2835_I2C_S_TA BIT(0)
+#define BCM2835_I2C_S_DONE BIT(1)
+#define BCM2835_I2C_S_TXW BIT(2)
+#define BCM2835_I2C_S_RXR BIT(3)
+#define BCM2835_I2C_S_TXD BIT(4)
+#define BCM2835_I2C_S_RXD BIT(5)
+#define BCM2835_I2C_S_TXE BIT(6)
+#define BCM2835_I2C_S_RXF BIT(7)
+#define BCM2835_I2C_S_ERR BIT(8)
+#define BCM2835_I2C_S_CLKT BIT(9)
+#define BCM2835_I2C_S_LEN BIT(10) /* Fake bit for SW error reporting */
+
+#define BCM2835_I2C_TIMEOUT (msecs_to_jiffies(1000))
+
+struct bcm2835_i2c_dev {
+ struct device *dev;
+ void __iomem *regs;
+ struct i2c_adapter adapter;
+ struct completion completion;
+ u32 msg_err;
+ u8 *msg_buf;
+ size_t msg_buf_remaining;
+};
+
+static inline void bcm2835_i2c_writel(struct bcm2835_i2c_dev *i2c_dev,
+ u32 reg, u32 val)
+{
+ writel(val, i2c_dev->regs + reg);
+}
+
+static inline u32 bcm2835_i2c_readl(struct bcm2835_i2c_dev *i2c_dev, u32 reg)
+{
+ return readl(i2c_dev->regs + reg);
+}
+
+static void bcm2835_fill_txfifo(struct bcm2835_i2c_dev *i2c_dev)
+{
+ u32 val;
+
+ for (;;) {
+ if (!i2c_dev->msg_buf_remaining)
+ return;
+ val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
+ if (!(val & BCM2835_I2C_S_TXD))
+ break;
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_FIFO,
+ *i2c_dev->msg_buf);
+ i2c_dev->msg_buf++;
+ i2c_dev->msg_buf_remaining--;
+ }
+}
+
+static void bcm2835_drain_rxfifo(struct bcm2835_i2c_dev *i2c_dev)
+{
+ u32 val;
+
+ for (;;) {
+ if (!i2c_dev->msg_buf_remaining)
+ return;
+ val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
+ if (!(val & BCM2835_I2C_S_RXD))
+ break;
+ *i2c_dev->msg_buf = bcm2835_i2c_readl(i2c_dev,
+ BCM2835_I2C_FIFO);
+ i2c_dev->msg_buf++;
+ i2c_dev->msg_buf_remaining--;
+ }
+}
+
+static irqreturn_t bcm2835_i2c_isr(int this_irq, void *data)
+{
+ struct bcm2835_i2c_dev *i2c_dev = data;
+ u32 val, err;
+
+ val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_S, val);
+
+ err = val & (BCM2835_I2C_S_CLKT | BCM2835_I2C_S_ERR);
+ if (err) {
+ i2c_dev->msg_err = err;
+ complete(&i2c_dev->completion);
+ return IRQ_HANDLED;
+ }
+
+ if (val & BCM2835_I2C_S_RXD) {
+ bcm2835_drain_rxfifo(i2c_dev);
+ if (!(val & BCM2835_I2C_S_DONE))
+ return IRQ_HANDLED;
+ }
+
+ if (val & BCM2835_I2C_S_DONE) {
+ if (i2c_dev->msg_buf_remaining)
+ i2c_dev->msg_err = BCM2835_I2C_S_LEN;
+ else
+ i2c_dev->msg_err = 0;
+ complete(&i2c_dev->completion);
+ return IRQ_HANDLED;
+ }
+
+ if (val & BCM2835_I2C_S_TXD) {
+ bcm2835_fill_txfifo(i2c_dev);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static int bcm2835_i2c_xfer_msg(struct bcm2835_i2c_dev *i2c_dev,
+ struct i2c_msg *msg)
+{
+ u32 c;
+ int ret;
+
+ i2c_dev->msg_buf = msg->buf;
+ i2c_dev->msg_buf_remaining = msg->len;
+ INIT_COMPLETION(i2c_dev->completion);
+
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, BCM2835_I2C_C_CLEAR);
+
+ if (msg->flags & I2C_M_RD) {
+ c = BCM2835_I2C_C_READ | BCM2835_I2C_C_INTR;
+ } else {
+ c = BCM2835_I2C_C_INTT;
+ bcm2835_fill_txfifo(i2c_dev);
+ }
+ c |= BCM2835_I2C_C_ST | BCM2835_I2C_C_INTD | BCM2835_I2C_C_I2CEN;
+
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_A, msg->addr);
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DLEN, msg->len);
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, c);
+
+ ret = wait_for_completion_timeout(&i2c_dev->completion,
+ BCM2835_I2C_TIMEOUT);
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, BCM2835_I2C_C_CLEAR);
+ if (WARN_ON(ret == 0)) {
+ dev_err(i2c_dev->dev, "i2c transfer timed out\n");
+ return -ETIMEDOUT;
+ }
+
+ if (likely(!i2c_dev->msg_err))
+ return 0;
+
+ if ((i2c_dev->msg_err & BCM2835_I2C_S_ERR) &&
+ (msg->flags & I2C_M_IGNORE_NAK))
+ return 0;
+
+ dev_err(i2c_dev->dev, "i2c transfer failed: %x\n", i2c_dev->msg_err);
+
+ if (i2c_dev->msg_err & BCM2835_I2C_S_ERR)
+ return -EREMOTEIO;
+ else
+ return -EIO;
+}
+
+static int bcm2835_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
+ int num)
+{
+ struct bcm2835_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
+ int i;
+ int ret = 0;
+
+ for (i = 0; i < num; i++) {
+ ret = bcm2835_i2c_xfer_msg(i2c_dev, &msgs[i]);
+ if (ret)
+ break;
+ }
+
+ return ret ?: i;
+}
+
+static u32 bcm2835_i2c_func(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm bcm2835_i2c_algo = {
+ .master_xfer = bcm2835_i2c_xfer,
+ .functionality = bcm2835_i2c_func,
+};
+
+static int __devinit bcm2835_i2c_probe(struct platform_device *pdev)
+{
+ struct bcm2835_i2c_dev *i2c_dev;
+ struct resource *mem, *requested, *irq;
+ int ret;
+ struct i2c_adapter *adap;
+
+ i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
+ if (!i2c_dev) {
+ dev_err(&pdev->dev, "Cannot allocate i2c_dev\n");
+ return -ENOMEM;
+ }
+ platform_set_drvdata(pdev, i2c_dev);
+ i2c_dev->dev = &pdev->dev;
+ init_completion(&i2c_dev->completion);
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(&pdev->dev, "No mem resource\n");
+ return -ENODEV;
+ }
+
+ requested = devm_request_mem_region(&pdev->dev, mem->start,
+ resource_size(mem),
+ dev_name(&pdev->dev));
+ if (!requested) {
+ dev_err(&pdev->dev, "Could not claim register region\n");
+ return -EBUSY;
+ }
+
+ i2c_dev->regs = devm_ioremap(&pdev->dev, mem->start,
+ resource_size(mem));
+ if (!i2c_dev->regs) {
+ dev_err(&pdev->dev, "Could not map registers\n");
+ return -ENOMEM;
+ }
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!irq) {
+ dev_err(&pdev->dev, "No IRQ resource\n");
+ return -ENODEV;
+ }
+
+ ret = devm_request_irq(&pdev->dev, irq->start, bcm2835_i2c_isr,
+ IRQF_SHARED, dev_name(&pdev->dev), i2c_dev);
+ if (ret) {
+ dev_err(&pdev->dev, "Could not request IRQ\n");
+ return -ENODEV;
+ }
+
+ adap = &i2c_dev->adapter;
+ i2c_set_adapdata(adap, i2c_dev);
+ adap->owner = THIS_MODULE;
+ adap->class = I2C_CLASS_HWMON;
+ strlcpy(adap->name, "bcm2835 I2C adapter", sizeof(adap->name));
+ adap->algo = &bcm2835_i2c_algo;
+ adap->dev.parent = &pdev->dev;
+ adap->nr = -1;
+
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, 0);
+
+ ret = i2c_add_numbered_adapter(adap);
+ if (ret) {
+ dev_err(&pdev->dev, "Could not add adapter\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int bcm2835_i2c_remove(struct platform_device *pdev)
+{
+ struct bcm2835_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&i2c_dev->adapter);
+
+ return 0;
+}
+
+static const struct of_device_id bcm2835_i2c_of_match[] = {
+ { .compatible = "brcm,bcm2835-i2c" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, bcm2835_i2c_of_match);
+
+static struct platform_driver bcm2835_i2c_driver = {
+ .probe = bcm2835_i2c_probe,
+ .remove = bcm2835_i2c_remove,
+ .driver = {
+ .name = "i2c-bcm2835",
+ .owner = THIS_MODULE,
+ .of_match_table = bcm2835_i2c_of_match,
+ },
+};
+
+static int __init bcm2835_i2c_init_driver(void)
+{
+ return platform_driver_register(&bcm2835_i2c_driver);
+}
+module_init(bcm2835_i2c_init_driver);
+
+static void __exit bcm2835_i2c_exit_driver(void)
+{
+ platform_driver_unregister(&bcm2835_i2c_driver);
+}
+module_exit(bcm2835_i2c_exit_driver);
+
+MODULE_AUTHOR("Stephen Warren <swarren@wwwdotorg.org>");
+MODULE_DESCRIPTION("BCM2835 I2C bus adapter");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:i2c-bcm2835");
This implements a very basic I2C host driver for the BCM2835 SoC. Missing features so far are: * Clock rate adjustment. * 10-bit addressing. * DMA. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> --- .../devicetree/bindings/i2c/brcm,bcm2835-i2c.txt | 20 ++ drivers/i2c/busses/Kconfig | 12 + drivers/i2c/busses/Makefile | 1 + drivers/i2c/busses/i2c-bcm2835.c | 331 ++++++++++++++++++++ 4 files changed, 364 insertions(+) create mode 100644 Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt create mode 100644 drivers/i2c/busses/i2c-bcm2835.c