@@ -5,58 +5,32 @@ Required properties:
- compatible : "via,vt8500-fb"
- reg : Should contain 1 register ranges(address and length)
- interrupts : framebuffer controller interrupt
-- display: a phandle pointing to the display node
+- bits-per-pixel : bit depth of framebuffer (16 or 32)
-Required nodes:
-- display: a display node is required to initialize the lcd panel
- This should be in the board dts.
-- default-mode: a videomode within the display with timing parameters
- as specified below.
+Required subnodes:
+- display-timings: see display-timing.txt for information
Example:
- fb@d800e400 {
+ fb@d8050800 {
compatible = "via,vt8500-fb";
reg = <0xd800e400 0x400>;
interrupts = <12>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
-VIA VT8500 Display
------------------------------------------------------
-Required properties (as per of_videomode_helper):
-
- - hactive, vactive: Display resolution
- - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters
- in pixels
- vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in
- lines
- - clock: displayclock in Hz
- - bpp: lcd panel bit-depth.
- <16> for RGB565, <32> for RGB888
-
-Optional properties (as per of_videomode_helper):
- - width-mm, height-mm: Display dimensions in mm
- - hsync-active-high (bool): Hsync pulse is active high
- - vsync-active-high (bool): Vsync pulse is active high
- - interlaced (bool): This is an interlaced mode
- - doublescan (bool): This is a doublescan mode
+ bits-per-pixel = <16>;
-Example:
- display: display@0 {
- modes {
- mode0: mode@0 {
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
+
@@ -4,20 +4,30 @@ Wondermedia WM8505 Framebuffer
Required properties:
- compatible : "wm,wm8505-fb"
- reg : Should contain 1 register ranges(address and length)
-- via,display: a phandle pointing to the display node
+- bits-per-pixel : bit depth of framebuffer (16 or 32)
-Required nodes:
-- display: a display node is required to initialize the lcd panel
- This should be in the board dts. See definition in
- Documentation/devicetree/bindings/video/via,vt8500-fb.txt
-- default-mode: a videomode node as specified in
- Documentation/devicetree/bindings/video/via,vt8500-fb.txt
+Required subnodes:
+- display-timings: see display-timing.txt for information
Example:
- fb@d8050800 {
+ fb@d8051700 {
compatible = "wm,wm8505-fb";
- reg = <0xd8050800 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
+ reg = <0xd8051700 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <40>;
+ hback-porch = <88>;
+ hsync-len = <0>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <1>;
+ };
+ };
};
@@ -12,24 +12,26 @@
/ {
model = "Benign BV07 Netbook";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ interrupt-parent = <&intc>;
+
+ fb@d8050800 {
+ compatible = "via,vt8500-fb";
+ reg = <0xd800e400 0x400>;
+ interrupts = <12>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
@@ -98,14 +98,6 @@
interrupts = <43>;
};
- fb@d800e400 {
- compatible = "via,vt8500-fb";
- reg = <0xd800e400 0x400>;
- interrupts = <12>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
@@ -12,24 +12,23 @@
/ {
model = "Wondermedia WM8505 Netbook";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ fb@d8050800 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8050800 0x200>;
+ bits-per-pixel = <32>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <32>; /* non-standard but required */
};
};
};
@@ -128,13 +128,6 @@
interrupts = <0>;
};
- fb@d8050800 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8050800 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
@@ -12,24 +12,23 @@
/ {
model = "Wondermedia WM8650-MID Tablet";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ fb@d8050800 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8050800 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
@@ -128,13 +128,6 @@
interrupts = <43>;
};
- fb@d8050800 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8050800 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
@@ -15,24 +15,23 @@
/ {
model = "Wondermedia WM8850-W70v2 Tablet";
- /*
- * Display node is based on Sascha Hauer's patch on dri-devel.
- * Added a bpp property to calculate the size of the framebuffer
- * until the binding is formalized.
- */
- display: display@0 {
- modes {
- mode0: mode@0 {
+ fb@d8051700 {
+ compatible = "wm,wm8505-fb";
+ reg = <0xd8051700 0x200>;
+ bits-per-pixel = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 800x480 {
+ clock-frequency = <0>; /* unused but required */
hactive = <800>;
vactive = <480>;
- hback-porch = <88>;
hfront-porch = <40>;
+ hback-porch = <88>;
hsync-len = <0>;
vback-porch = <32>;
vfront-porch = <11>;
vsync-len = <1>;
- clock = <0>; /* unused but required */
- bpp = <16>; /* non-standard but required */
};
};
};
@@ -135,13 +135,6 @@
};
};
- fb@d8051700 {
- compatible = "wm,wm8505-fb";
- reg = <0xd8051700 0x200>;
- display = <&display>;
- default-mode = <&mode0>;
- };
-
ge_rops@d8050400 {
compatible = "wm,prizm-ge-rops";
reg = <0xd8050400 0x100>;
@@ -1794,6 +1794,9 @@ config FB_VT8500
select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_DISPLAY_TIMING
+ select OF_VIDEOMODE
help
This is the framebuffer driver for VIA VT8500 integrated LCD
controller.
@@ -1804,6 +1807,9 @@ config FB_WM8505
select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
select FB_SYS_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_DISPLAY_TIMING
+ select OF_VIDEOMODE
help
This is the framebuffer driver for WonderMedia WM8xxx-series
integrated LCD controller. This driver covers the WM8505, WM8650
@@ -15,20 +15,21 @@
* GNU General Public License for more details.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/string.h>
#include <linux/wait.h>
+#include <video/of_display_timing.h>
#include "vt8500lcdfb.h"
@@ -290,11 +291,11 @@ static int vt8500lcd_probe(struct platform_device *pdev)
{
struct vt8500lcd_info *fbi;
struct resource *res;
+ struct display_timings *disp_timing;
void *addr;
int irq, ret;
struct fb_videomode of_mode;
- struct device_node *np;
u32 bpp;
dma_addr_t fb_mem_phys;
unsigned long fb_mem_len;
@@ -359,31 +360,19 @@ static int vt8500lcd_probe(struct platform_device *pdev)
goto failed_free_res;
}
- np = of_parse_phandle(pdev->dev.of_node, "default-mode", 0);
- if (!np) {
- pr_err("%s: No display description in Device Tree\n", __func__);
- ret = -EINVAL;
- goto failed_free_res;
- }
+ disp_timing = of_get_display_timings(pdev->dev.of_node);
+ if (!disp_timing)
+ return -EINVAL;
+
+ ret = of_get_fb_videomode(pdev->dev.of_node, &of_mode,
+ OF_USE_NATIVE_MODE);
+ if (ret)
+ return ret;
+
+ ret = of_property_read_u32(pdev->dev.of_node, "bits-per-pixel", &bpp);
+ if (ret)
+ return ret;
- /*
- * This code is copied from Sascha Hauer's of_videomode helper
- * and can be replaced with a call to the helper once mainlined
- */
- ret = 0;
- ret |= of_property_read_u32(np, "hactive", &of_mode.xres);
- ret |= of_property_read_u32(np, "vactive", &of_mode.yres);
- ret |= of_property_read_u32(np, "hback-porch", &of_mode.left_margin);
- ret |= of_property_read_u32(np, "hfront-porch", &of_mode.right_margin);
- ret |= of_property_read_u32(np, "hsync-len", &of_mode.hsync_len);
- ret |= of_property_read_u32(np, "vback-porch", &of_mode.upper_margin);
- ret |= of_property_read_u32(np, "vfront-porch", &of_mode.lower_margin);
- ret |= of_property_read_u32(np, "vsync-len", &of_mode.vsync_len);
- ret |= of_property_read_u32(np, "bpp", &bpp);
- if (ret) {
- pr_err("%s: Unable to read display properties\n", __func__);
- goto failed_free_res;
- }
of_mode.vmode = FB_VMODE_NONINTERLACED;
/* try allocating the framebuffer */
@@ -14,23 +14,24 @@
* GNU General Public License for more details.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
#include <linux/delay.h>
+#include <linux/dma-mapping.h>
#include <linux/fb.h>
+#include <linux/errno.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/wait.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_fdt.h>
-#include <linux/memblock.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/wait.h>
+#include <video/of_display_timing.h>
#include "wm8505fb_regs.h"
@@ -276,12 +277,12 @@ static struct fb_ops wm8505fb_ops = {
static int wm8505fb_probe(struct platform_device *pdev)
{
struct wm8505fb_info *fbi;
- struct resource *res;
+ struct resource *res;
+ struct display_timings *disp_timing;
void *addr;
int ret;
- struct fb_videomode of_mode;
- struct device_node *np;
+ struct fb_videomode mode;
u32 bpp;
dma_addr_t fb_mem_phys;
unsigned long fb_mem_len;
@@ -321,33 +322,20 @@ static int wm8505fb_probe(struct platform_device *pdev)
if (fbi->regbase == NULL)
return -EBUSY;
- np = of_parse_phandle(pdev->dev.of_node, "default-mode", 0);
- if (!np) {
- pr_err("%s: No display description in Device Tree\n", __func__);
+ disp_timing = of_get_display_timings(pdev->dev.of_node);
+ if (!disp_timing)
return -EINVAL;
- }
- /*
- * This code is copied from Sascha Hauer's of_videomode helper
- * and can be replaced with a call to the helper once mainlined
- */
- ret = 0;
- ret |= of_property_read_u32(np, "hactive", &of_mode.xres);
- ret |= of_property_read_u32(np, "vactive", &of_mode.yres);
- ret |= of_property_read_u32(np, "hback-porch", &of_mode.left_margin);
- ret |= of_property_read_u32(np, "hfront-porch", &of_mode.right_margin);
- ret |= of_property_read_u32(np, "hsync-len", &of_mode.hsync_len);
- ret |= of_property_read_u32(np, "vback-porch", &of_mode.upper_margin);
- ret |= of_property_read_u32(np, "vfront-porch", &of_mode.lower_margin);
- ret |= of_property_read_u32(np, "vsync-len", &of_mode.vsync_len);
- ret |= of_property_read_u32(np, "bpp", &bpp);
- if (ret) {
- pr_err("%s: Unable to read display properties\n", __func__);
- return -EINVAL;
- }
+ ret = of_get_fb_videomode(pdev->dev.of_node, &mode, OF_USE_NATIVE_MODE);
+ if (ret)
+ return ret;
+
+ ret = of_property_read_u32(pdev->dev.of_node, "bits-per-pixel", &bpp);
+ if (ret)
+ return ret;
- of_mode.vmode = FB_VMODE_NONINTERLACED;
- fb_videomode_to_var(&fbi->fb.var, &of_mode);
+ mode.vmode = FB_VMODE_NONINTERLACED;
+ fb_videomode_to_var(&fbi->fb.var, &mode);
fbi->fb.var.nonstd = 0;
fbi->fb.var.activate = FB_ACTIVATE_NOW;
@@ -356,7 +344,7 @@ static int wm8505fb_probe(struct platform_device *pdev)
fbi->fb.var.width = -1;
/* try allocating the framebuffer */
- fb_mem_len = of_mode.xres * of_mode.yres * 2 * (bpp / 8);
+ fb_mem_len = mode.xres * mode.yres * 2 * (bpp / 8);
fb_mem_virt = dmam_alloc_coherent(&pdev->dev, fb_mem_len, &fb_mem_phys,
GFP_KERNEL);
if (!fb_mem_virt) {
@@ -364,8 +352,8 @@ static int wm8505fb_probe(struct platform_device *pdev)
return -ENOMEM;
}
- fbi->fb.var.xres_virtual = of_mode.xres;
- fbi->fb.var.yres_virtual = of_mode.yres * 2;
+ fbi->fb.var.xres_virtual = mode.xres;
+ fbi->fb.var.yres_virtual = mode.yres * 2;
fbi->fb.var.bits_per_pixel = bpp;
fbi->fb.fix.smem_start = fb_mem_phys;
Now that a display timing binding is available, convert our almost identical binding to use the standard binding. This patch converts the vt8500 and wm8505 framebuffer drivers and associated dts/dtsi files to use the standard binding as defined in bindings/video/display-timing.txt. There are two side-effects of making this conversion: 1) The fb node should now be in the board file, rather than the soc file as the display-timing node is a child of the fb node. 2) We still require a bits per pixel property to initialize the framebuffer for the different lcd panels. Rather than including this as part of the display timing, it is moved into the framebuffer node. I have also taken the opportunity to alphabetise the includes of each driver to avoid double-ups. Signed-off-by: Tony Prisk <linux@prisktech.co.nz> --- .../devicetree/bindings/video/via,vt8500-fb.txt | 48 ++++---------- .../devicetree/bindings/video/wm,wm8505-fb.txt | 32 +++++---- arch/arm/boot/dts/vt8500-bv07.dts | 24 +++---- arch/arm/boot/dts/vt8500.dtsi | 8 --- arch/arm/boot/dts/wm8505-ref.dts | 21 +++--- arch/arm/boot/dts/wm8505.dtsi | 7 -- arch/arm/boot/dts/wm8650-mid.dts | 21 +++--- arch/arm/boot/dts/wm8650.dtsi | 7 -- arch/arm/boot/dts/wm8850-w70v2.dts | 21 +++--- arch/arm/boot/dts/wm8850.dtsi | 7 -- drivers/video/Kconfig | 6 ++ drivers/video/vt8500lcdfb.c | 53 ++++++--------- drivers/video/wm8505fb.c | 68 ++++++++------------ 13 files changed, 130 insertions(+), 193 deletions(-)