| Message ID | 1372692155-17653-9-git-send-email-s.nawrocki@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Sylwester, On Monday 01 of July 2013 17:22:30 Sylwester Nawrocki wrote: > This patch enables the front camera using the internal > camera ISP (FIMC-IS). > > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> > Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> > --- > arch/arm/boot/dts/exynos4412-trats2.dts | 91 > +++++++++++++++++++++++++++++++ 1 file changed, 91 insertions(+) > > diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts > b/arch/arm/boot/dts/exynos4412-trats2.dts index b9de3b5..e9fb3de 100644 > --- a/arch/arm/boot/dts/exynos4412-trats2.dts > +++ b/arch/arm/boot/dts/exynos4412-trats2.dts > @@ -62,6 +62,15 @@ > enable-active-high; > }; > > + cam_io_reg: voltage-regulator@3 { Same comment here as for patch 7/13. This is not an address of this regulator, so I would rather use -3 prefix. > + compatible = "regulator-fixed"; > + regulator-name = "CAM_SENSOR_A"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + gpio = <&gpm0 2 0>; > + enable-active-high; > + }; > + > /* More to come */ > }; > > @@ -472,4 +481,86 @@ > gpios = <&gpj0 7 0>; > }; > }; > + > + camera { > + pinctrl-names = "default"; > + pinctrl-0 = <&cam_port_b_clk_active>; > + status = "okay"; > + > + fimc_0: fimc@11800000 { > + clock-frequency = <160000000>; > + status = "okay"; > + }; > + > + fimc_1: fimc@11810000 { > + clock-frequency = <160000000>; > + status = "okay"; > + }; > + > + fimc_2: fimc@11820000 { > + clock-frequency = <160000000>; > + status = "okay"; > + }; > + > + fimc_3: fimc@11830000 { > + clock-frequency = <160000000>; > + status = "okay"; > + }; > + > + csis_1: csis@11890000 { > + vddcore-supply = <&ldo8_reg>; > + vddio-supply = <&ldo10_reg>; > + clock-frequency = <160000000>; > + #address-cells = <1>; > + #size-cells = <0>; Hmm. Couldn't the two #properties above be moved to exynos4.dtsi instead? Otherwise looks good. Best regards, Tomasz > + status = "okay"; > + > + /* Camera D (4) MIPI CSI-2 (CSIS1) */ > + port@4 { > + reg = <4>; > + csis1_ep: endpoint { > + remote-endpoint = <&is_s5k6a3_ep>; > + data-lanes = <1>; > + samsung,csis-hs-settle = <18>; > + samsung,csis-wclk; > + }; > + }; > + }; > + > + fimc_lite_0: fimc-lite@12390000 { > + status = "okay"; > + }; > + > + fimc_lite_1: fimc-lite@123A0000 { > + status = "okay"; > + }; > + > + fimc-is@12000000 { > + pinctrl-0 = <&fimc_is_uart>; > + pinctrl-names = "default"; > + status = "okay"; > + > + i2c1_isp: i2c-isp@12140000 { > + pinctrl-0 = <&fimc_is_i2c1>; > + pinctrl-names = "default"; > + > + s5k6a3@10 { > + compatible = "samsung,s5k6a3"; > + reg = <0x10>; > + svdda-supply = <&cam_io_reg>; > + svddio-supply = <&ldo19_reg>; > + clock-frequency = <24000000>; > + samsung,camclk-out = <1>; > + gpios = <&gpm1 6 0>; > + > + port { > + is_s5k6a3_ep: endpoint { > + remote-endpoint = <&csis1_ep>; > + data-lanes = <1>; > + }; > + }; > + }; > + }; > + }; > + }; > }; -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 07/06/2013 01:23 AM, Tomasz Figa wrote: > On Monday 01 of July 2013 17:22:30 Sylwester Nawrocki wrote: >> This patch enables the front camera using the internal >> camera ISP (FIMC-IS). >> >> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> >> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> >> --- >> arch/arm/boot/dts/exynos4412-trats2.dts | 91 >> +++++++++++++++++++++++++++++++ 1 file changed, 91 insertions(+) >> >> diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts >> b/arch/arm/boot/dts/exynos4412-trats2.dts index b9de3b5..e9fb3de 100644 >> --- a/arch/arm/boot/dts/exynos4412-trats2.dts >> +++ b/arch/arm/boot/dts/exynos4412-trats2.dts >> @@ -62,6 +62,15 @@ >> enable-active-high; >> }; >> >> + cam_io_reg: voltage-regulator@3 { > > Same comment here as for patch 7/13. This is not an address of this > regulator, so I would rather use -3 prefix. Yes, and this is the convention already used in this 'regulators' node. I'll rename that node to 'voltage-regulator-1'. >> + compatible = "regulator-fixed"; >> + regulator-name = "CAM_SENSOR_A"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + gpio = <&gpm0 2 0>; >> + enable-active-high; >> + }; >> + >> /* More to come */ >> }; >> >> @@ -472,4 +481,86 @@ >> gpios = <&gpj0 7 0>; >> }; >> }; >> + >> + camera { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&cam_port_b_clk_active>; >> + status = "okay"; >> + >> + fimc_0: fimc@11800000 { >> + clock-frequency = <160000000>; >> + status = "okay"; >> + }; >> + >> + fimc_1: fimc@11810000 { >> + clock-frequency = <160000000>; >> + status = "okay"; >> + }; >> + >> + fimc_2: fimc@11820000 { >> + clock-frequency = <160000000>; >> + status = "okay"; >> + }; >> + >> + fimc_3: fimc@11830000 { >> + clock-frequency = <160000000>; >> + status = "okay"; >> + }; >> + >> + csis_1: csis@11890000 { >> + vddcore-supply = <&ldo8_reg>; >> + vddio-supply = <&ldo10_reg>; >> + clock-frequency = <160000000>; >> + #address-cells = <1>; >> + #size-cells = <0>; > > Hmm. Couldn't the two #properties above be moved to exynos4.dtsi instead? Normally the port/endpoint nodes are board specific. But since the binding requires at least one port and endpoint node, these properties will always need to be specified. Thus it's a good idea to move them to exynos4.dtsi. -- Thanks, Sylwester -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index b9de3b5..e9fb3de 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -62,6 +62,15 @@ enable-active-high; }; + cam_io_reg: voltage-regulator@3 { + compatible = "regulator-fixed"; + regulator-name = "CAM_SENSOR_A"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpm0 2 0>; + enable-active-high; + }; + /* More to come */ }; @@ -472,4 +481,86 @@ gpios = <&gpj0 7 0>; }; }; + + camera { + pinctrl-names = "default"; + pinctrl-0 = <&cam_port_b_clk_active>; + status = "okay"; + + fimc_0: fimc@11800000 { + clock-frequency = <160000000>; + status = "okay"; + }; + + fimc_1: fimc@11810000 { + clock-frequency = <160000000>; + status = "okay"; + }; + + fimc_2: fimc@11820000 { + clock-frequency = <160000000>; + status = "okay"; + }; + + fimc_3: fimc@11830000 { + clock-frequency = <160000000>; + status = "okay"; + }; + + csis_1: csis@11890000 { + vddcore-supply = <&ldo8_reg>; + vddio-supply = <&ldo10_reg>; + clock-frequency = <160000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + /* Camera D (4) MIPI CSI-2 (CSIS1) */ + port@4 { + reg = <4>; + csis1_ep: endpoint { + remote-endpoint = <&is_s5k6a3_ep>; + data-lanes = <1>; + samsung,csis-hs-settle = <18>; + samsung,csis-wclk; + }; + }; + }; + + fimc_lite_0: fimc-lite@12390000 { + status = "okay"; + }; + + fimc_lite_1: fimc-lite@123A0000 { + status = "okay"; + }; + + fimc-is@12000000 { + pinctrl-0 = <&fimc_is_uart>; + pinctrl-names = "default"; + status = "okay"; + + i2c1_isp: i2c-isp@12140000 { + pinctrl-0 = <&fimc_is_i2c1>; + pinctrl-names = "default"; + + s5k6a3@10 { + compatible = "samsung,s5k6a3"; + reg = <0x10>; + svdda-supply = <&cam_io_reg>; + svddio-supply = <&ldo19_reg>; + clock-frequency = <24000000>; + samsung,camclk-out = <1>; + gpios = <&gpm1 6 0>; + + port { + is_s5k6a3_ep: endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; + }; + }; };