| Message ID | 1379946998-23041-8-git-send-email-jbe@pengutronix.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 09/23/13 15:36, Juergen Beisert wrote: > Signed-off-by: Juergen Beisert <jbe@pengutronix.de> > CC: linux-arm-kernel@lists.infradead.org > CC: linux-input@vger.kernel.org > CC: devel@driverdev.osuosl.org > CC: Marek Vasut <marex@denx.de> > CC: Fabio Estevam <fabio.estevam@freescale.com> > CC: Jonathan Cameron <jic23@cam.ac.uk> Applied to the togreg branch of iio.git Thanks, > --- > drivers/staging/iio/adc/mxs-lradc.c | 163 ------------------------------------ > 1 file changed, 163 deletions(-) > > diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c > index 76a900d..aa1f337 100644 > --- a/drivers/staging/iio/adc/mxs-lradc.c > +++ b/drivers/staging/iio/adc/mxs-lradc.c > @@ -186,7 +186,6 @@ struct mxs_lradc { > bool use_touchbutton; > > struct input_dev *ts_input; > - struct work_struct ts_work; > > enum mxs_lradc_id soc; > enum lradc_ts_plate cur_plate; /* statemachine */ > @@ -830,168 +829,6 @@ static const struct iio_info mxs_lradc_iio_info = { > .read_raw = mxs_lradc_read_raw, > }; > > -static int mxs_lradc_ts_touched(struct mxs_lradc *lradc) > -{ > - uint32_t reg; > - > - /* Enable touch detection. */ > - mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0); > - mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc), > - LRADC_CTRL0); > - > - msleep(LRADC_TS_SAMPLE_DELAY_MS); > - > - reg = readl(lradc->base + LRADC_STATUS); > - > - return reg & LRADC_STATUS_TOUCH_DETECT_RAW; > -} > - > -static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc, > - enum lradc_ts_plate plate, int change) > -{ > - unsigned long delay, jiff; > - uint32_t reg, ctrl0 = 0, chan = 0; > - /* The touchscreen always uses CTRL4 slot #7. */ > - const uint8_t slot = 7; > - uint32_t val; > - > - /* > - * There are three correct configurations of the controller sampling > - * the touchscreen, each of these configuration provides different > - * information from the touchscreen. > - * > - * The following table describes the sampling configurations: > - * +-------------+-------+-------+-------+ > - * | Wire \ Axis | X | Y | Z | > - * +---------------------+-------+-------+ > - * | X+ (CH2) | HI | TS | TS | > - * +-------------+-------+-------+-------+ > - * | X- (CH4) | LO | SH | HI | > - * +-------------+-------+-------+-------+ > - * | Y+ (CH3) | SH | HI | HI | > - * +-------------+-------+-------+-------+ > - * | Y- (CH5) | TS | LO | SH | > - * +-------------+-------+-------+-------+ > - * > - * HI ... strong '1' ; LO ... strong '0' > - * SH ... sample here ; TS ... tri-state > - * > - * There are a few other ways of obtaining the Z coordinate > - * (aka. pressure), but the one in the table seems to be the > - * most reliable one. > - */ > - switch (plate) { > - case LRADC_SAMPLE_X: > - ctrl0 = mxs_lradc_drive_x_plate(lradc); > - chan = 3; > - break; > - case LRADC_SAMPLE_Y: > - ctrl0 = mxs_lradc_drive_y_plate(lradc); > - chan = 4; > - break; > - case LRADC_SAMPLE_PRESSURE: > - ctrl0 = mxs_lradc_drive_pressure(lradc); > - chan = 5; > - break; > - } > - > - if (change) { > - mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), > - LRADC_CTRL0); > - mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0); > - > - mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot), > - LRADC_CTRL4); > - mxs_lradc_reg_set(lradc, > - chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot), > - LRADC_CTRL4); > - } > - > - mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot)); > - mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0); > - > - delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS); > - do { > - jiff = jiffies; > - reg = readl_relaxed(lradc->base + LRADC_CTRL1); > - if (reg & LRADC_CTRL1_LRADC_IRQ(slot)) > - break; > - } while (time_before(jiff, delay)); > - > - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1); > - > - if (time_after_eq(jiff, delay)) > - return -ETIMEDOUT; > - > - val = readl(lradc->base + LRADC_CH(slot)); > - val &= LRADC_CH_VALUE_MASK; > - > - return val; > -} > - > -static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc, > - enum lradc_ts_plate plate) > -{ > - int32_t val, tot = 0; > - int i; > - > - val = mxs_lradc_ts_sample(lradc, plate, 1); > - > - /* Delay a bit so the touchscreen is stable. */ > - mdelay(2); > - > - for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) { > - val = mxs_lradc_ts_sample(lradc, plate, 0); > - tot += val; > - } > - > - return tot / LRADC_TS_SAMPLE_AMOUNT; > -} > - > -static void mxs_lradc_ts_work(struct work_struct *ts_work) > -{ > - struct mxs_lradc *lradc = container_of(ts_work, > - struct mxs_lradc, ts_work); > - int val_x, val_y, val_p; > - bool valid = false; > - > - while (mxs_lradc_ts_touched(lradc)) { > - /* Disable touch detector so we can sample the touchscreen. */ > - mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), > - LRADC_CTRL0); > - > - if (likely(valid)) { > - input_report_abs(lradc->ts_input, ABS_X, val_x); > - input_report_abs(lradc->ts_input, ABS_Y, val_y); > - input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p); > - input_report_key(lradc->ts_input, BTN_TOUCH, 1); > - input_sync(lradc->ts_input); > - } > - > - valid = false; > - > - val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X); > - if (val_x < 0) > - continue; > - val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y); > - if (val_y < 0) > - continue; > - val_p = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_PRESSURE); > - if (val_p < 0) > - continue; > - > - valid = true; > - } > - > - input_report_abs(lradc->ts_input, ABS_PRESSURE, 0); > - input_report_key(lradc->ts_input, BTN_TOUCH, 0); > - input_sync(lradc->ts_input); > - > - /* Restart the touchscreen interrupts. */ > - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1); > - mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1); > -} > - > static int mxs_lradc_ts_open(struct input_dev *dev) > { > struct mxs_lradc *lradc = input_get_drvdata(dev); > -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index 76a900d..aa1f337 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -186,7 +186,6 @@ struct mxs_lradc { bool use_touchbutton; struct input_dev *ts_input; - struct work_struct ts_work; enum mxs_lradc_id soc; enum lradc_ts_plate cur_plate; /* statemachine */ @@ -830,168 +829,6 @@ static const struct iio_info mxs_lradc_iio_info = { .read_raw = mxs_lradc_read_raw, }; -static int mxs_lradc_ts_touched(struct mxs_lradc *lradc) -{ - uint32_t reg; - - /* Enable touch detection. */ - mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0); - mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc), - LRADC_CTRL0); - - msleep(LRADC_TS_SAMPLE_DELAY_MS); - - reg = readl(lradc->base + LRADC_STATUS); - - return reg & LRADC_STATUS_TOUCH_DETECT_RAW; -} - -static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc, - enum lradc_ts_plate plate, int change) -{ - unsigned long delay, jiff; - uint32_t reg, ctrl0 = 0, chan = 0; - /* The touchscreen always uses CTRL4 slot #7. */ - const uint8_t slot = 7; - uint32_t val; - - /* - * There are three correct configurations of the controller sampling - * the touchscreen, each of these configuration provides different - * information from the touchscreen. - * - * The following table describes the sampling configurations: - * +-------------+-------+-------+-------+ - * | Wire \ Axis | X | Y | Z | - * +---------------------+-------+-------+ - * | X+ (CH2) | HI | TS | TS | - * +-------------+-------+-------+-------+ - * | X- (CH4) | LO | SH | HI | - * +-------------+-------+-------+-------+ - * | Y+ (CH3) | SH | HI | HI | - * +-------------+-------+-------+-------+ - * | Y- (CH5) | TS | LO | SH | - * +-------------+-------+-------+-------+ - * - * HI ... strong '1' ; LO ... strong '0' - * SH ... sample here ; TS ... tri-state - * - * There are a few other ways of obtaining the Z coordinate - * (aka. pressure), but the one in the table seems to be the - * most reliable one. - */ - switch (plate) { - case LRADC_SAMPLE_X: - ctrl0 = mxs_lradc_drive_x_plate(lradc); - chan = 3; - break; - case LRADC_SAMPLE_Y: - ctrl0 = mxs_lradc_drive_y_plate(lradc); - chan = 4; - break; - case LRADC_SAMPLE_PRESSURE: - ctrl0 = mxs_lradc_drive_pressure(lradc); - chan = 5; - break; - } - - if (change) { - mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), - LRADC_CTRL0); - mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0); - - mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot), - LRADC_CTRL4); - mxs_lradc_reg_set(lradc, - chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot), - LRADC_CTRL4); - } - - mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot)); - mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0); - - delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS); - do { - jiff = jiffies; - reg = readl_relaxed(lradc->base + LRADC_CTRL1); - if (reg & LRADC_CTRL1_LRADC_IRQ(slot)) - break; - } while (time_before(jiff, delay)); - - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1); - - if (time_after_eq(jiff, delay)) - return -ETIMEDOUT; - - val = readl(lradc->base + LRADC_CH(slot)); - val &= LRADC_CH_VALUE_MASK; - - return val; -} - -static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc, - enum lradc_ts_plate plate) -{ - int32_t val, tot = 0; - int i; - - val = mxs_lradc_ts_sample(lradc, plate, 1); - - /* Delay a bit so the touchscreen is stable. */ - mdelay(2); - - for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) { - val = mxs_lradc_ts_sample(lradc, plate, 0); - tot += val; - } - - return tot / LRADC_TS_SAMPLE_AMOUNT; -} - -static void mxs_lradc_ts_work(struct work_struct *ts_work) -{ - struct mxs_lradc *lradc = container_of(ts_work, - struct mxs_lradc, ts_work); - int val_x, val_y, val_p; - bool valid = false; - - while (mxs_lradc_ts_touched(lradc)) { - /* Disable touch detector so we can sample the touchscreen. */ - mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc), - LRADC_CTRL0); - - if (likely(valid)) { - input_report_abs(lradc->ts_input, ABS_X, val_x); - input_report_abs(lradc->ts_input, ABS_Y, val_y); - input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p); - input_report_key(lradc->ts_input, BTN_TOUCH, 1); - input_sync(lradc->ts_input); - } - - valid = false; - - val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X); - if (val_x < 0) - continue; - val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y); - if (val_y < 0) - continue; - val_p = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_PRESSURE); - if (val_p < 0) - continue; - - valid = true; - } - - input_report_abs(lradc->ts_input, ABS_PRESSURE, 0); - input_report_key(lradc->ts_input, BTN_TOUCH, 0); - input_sync(lradc->ts_input); - - /* Restart the touchscreen interrupts. */ - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1); - mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1); -} - static int mxs_lradc_ts_open(struct input_dev *dev) { struct mxs_lradc *lradc = input_get_drvdata(dev);
Signed-off-by: Juergen Beisert <jbe@pengutronix.de> CC: linux-arm-kernel@lists.infradead.org CC: linux-input@vger.kernel.org CC: devel@driverdev.osuosl.org CC: Marek Vasut <marex@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Jonathan Cameron <jic23@cam.ac.uk> --- drivers/staging/iio/adc/mxs-lradc.c | 163 ------------------------------------ 1 file changed, 163 deletions(-)