new file mode 100644
@@ -0,0 +1,7 @@
+AU Optronics Corporation 10.1" WSVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,b101aw03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
new file mode 100644
@@ -0,0 +1,7 @@
+Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "chunghwa,claa101wb03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
new file mode 100644
@@ -0,0 +1,7 @@
+Panasonic Corporation 10.1" WUXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "panasonic,vvx10f004b00"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
new file mode 100644
@@ -0,0 +1,21 @@
+Simple display panel
+
+Required properties:
+- power-supply: regulator to provide the supply voltage
+
+Optional properties:
+- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+
+Example:
+
+ panel: panel {
+ compatible = "cptt,claa101wb01";
+ ddc-i2c-bus = <&panelddc>;
+
+ power-supply = <&vdd_pnl_reg>;
+ enable-gpios = <&gpio 90 0>;
+
+ backlight = <&backlight>;
+ };
@@ -58,3 +58,4 @@ obj-$(CONFIG_DRM_QXL) += qxl/
obj-$(CONFIG_DRM_MSM) += msm/
obj-$(CONFIG_DRM_TEGRA) += tegra/
obj-y += i2c/
+obj-y += panel/
@@ -2,3 +2,16 @@ menuconfig DRM_PANEL
bool "DRM panel support"
help
Panel registration and lookup framework.
+
+if DRM_PANEL
+
+config DRM_PANEL_SIMPLE
+ bool "support for simple panels"
+ depends on OF
+ help
+ DRM panel driver for dumb panels that need at most a regulator and
+ a GPIO to be powered up. Optionally a backlight can be attached so
+ that it can be automatically turned off when the panel goes into a
+ low power state.
+
+endif
new file mode 100644
@@ -0,0 +1 @@
+obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
new file mode 100644
@@ -0,0 +1,339 @@
+/*
+ * Copyright (C) 2013, NVIDIA Corporation. All rights reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sub license,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the
+ * next paragraph) shall be included in all copies or substantial portions
+ * of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ */
+
+#include <linux/backlight.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drm_crtc.h>
+#include <drm/drm_panel.h>
+
+struct panel_desc {
+ const struct drm_display_mode *modes;
+ unsigned int num_modes;
+
+ struct {
+ unsigned int width;
+ unsigned int height;
+ } size;
+};
+
+/* TODO: convert to gpiod_*() API once it's been merged */
+#define GPIO_ACTIVE_LOW (1 << 0)
+
+struct panel_simple {
+ struct drm_panel base;
+ bool enabled;
+
+ const struct panel_desc *desc;
+
+ struct backlight_device *backlight;
+ struct regulator *supply;
+
+ unsigned long enable_gpio_flags;
+ int enable_gpio;
+};
+
+static inline struct panel_simple *to_panel_simple(struct drm_panel *panel)
+{
+ return container_of(panel, struct panel_simple, base);
+}
+
+static void panel_simple_disable(struct drm_panel *panel)
+{
+ struct panel_simple *p = to_panel_simple(panel);
+
+ if (!p->enabled)
+ return;
+
+ if (p->backlight) {
+ p->backlight->props.power = FB_BLANK_POWERDOWN;
+ backlight_update_status(p->backlight);
+ }
+
+ if (gpio_is_valid(p->enable_gpio)) {
+ if (p->enable_gpio_flags & GPIO_ACTIVE_LOW)
+ gpio_set_value(p->enable_gpio, 1);
+ else
+ gpio_set_value(p->enable_gpio, 0);
+ }
+
+ regulator_disable(p->supply);
+ p->enabled = false;
+}
+
+static void panel_simple_enable(struct drm_panel *panel)
+{
+ struct panel_simple *p = to_panel_simple(panel);
+ int err;
+
+ if (p->enabled)
+ return;
+
+ err = regulator_enable(p->supply);
+ if (err < 0)
+ dev_err(panel->dev, "failed to enable supply: %d\n", err);
+
+ if (gpio_is_valid(p->enable_gpio)) {
+ if (p->enable_gpio_flags & GPIO_ACTIVE_LOW)
+ gpio_set_value(p->enable_gpio, 0);
+ else
+ gpio_set_value(p->enable_gpio, 1);
+ }
+
+ if (p->backlight) {
+ p->backlight->props.power = FB_BLANK_UNBLANK;
+ backlight_update_status(p->backlight);
+ }
+
+ p->enabled = true;
+}
+
+static int panel_simple_get_modes(struct drm_panel *panel)
+{
+ struct panel_simple *p = to_panel_simple(panel);
+ struct drm_display_mode *mode;
+ unsigned int i;
+
+ for (i = 0; i < p->desc->num_modes; i++) {
+ mode = drm_mode_duplicate(panel->drm, &p->desc->modes[i]);
+ if (!mode)
+ return -ENOMEM;
+
+ drm_mode_set_name(mode);
+
+ drm_mode_probed_add(panel->connector, mode);
+ }
+
+ return p->desc->num_modes;
+}
+
+static const struct drm_panel_funcs panel_simple_funcs = {
+ .disable = panel_simple_disable,
+ .enable = panel_simple_enable,
+ .get_modes = panel_simple_get_modes,
+};
+
+static const struct drm_display_mode auo_b101aw03_mode = {
+ .clock = 51450,
+ .hdisplay = 1024,
+ .hsync_start = 1024 + 156,
+ .hsync_end = 1024 + 156 + 8,
+ .htotal = 1024 + 156 + 8 + 156,
+ .vdisplay = 600,
+ .vsync_start = 600 + 16,
+ .vsync_end = 600 + 16 + 6,
+ .vtotal = 600 + 16 + 6 + 16,
+ .vrefresh = 60,
+};
+
+static const struct panel_desc auo_b101aw03 = {
+ .modes = &auo_b101aw03_mode,
+ .num_modes = 1,
+ .size = {
+ .width = 223,
+ .height = 125,
+ },
+};
+
+static const struct drm_display_mode chunghwa_claa101wb01_mode = {
+ .clock = 69300,
+ .hdisplay = 1366,
+ .hsync_start = 1366 + 48,
+ .hsync_end = 1366 + 48 + 32,
+ .htotal = 1366 + 48 + 32 + 20,
+ .vdisplay = 768,
+ .vsync_start = 768 + 16,
+ .vsync_end = 768 + 16 + 8,
+ .vtotal = 768 + 16 + 8 + 16,
+ .vrefresh = 60,
+};
+
+static const struct panel_desc chunghwa_claa101wb01 = {
+ .modes = &chunghwa_claa101wb01_mode,
+ .num_modes = 1,
+ .size = {
+ .width = 223,
+ .height = 125,
+ },
+};
+
+static const struct drm_display_mode panasonic_vvx10f004b00_mode = {
+ .clock = 154700,
+ .hdisplay = 1920,
+ .hsync_start = 1920 + 154,
+ .hsync_end = 1920 + 154 + 16,
+ .htotal = 1920 + 154 + 16 + 32,
+ .vdisplay = 1200,
+ .vsync_start = 1200 + 17,
+ .vsync_end = 1200 + 17 + 2,
+ .vtotal = 1200 + 17 + 2 + 16,
+ .vrefresh = 60,
+};
+
+static const struct panel_desc panasonic_vvx10f004b00 = {
+ .modes = &panasonic_vvx10f004b00_mode,
+ .num_modes = 1,
+ .size = {
+ .width = 217,
+ .height = 136,
+ },
+};
+
+static const struct of_device_id panel_simple_of_match[] = {
+ {
+ .compatible = "auo,b101aw03",
+ .data = &auo_b101aw03,
+ }, {
+ .compatible = "chunghwa,claa101wb01",
+ .data = &chunghwa_claa101wb01
+ }, {
+ .compatible = "panasonic,vvx10f004b00",
+ .data = &panasonic_vvx10f004b00
+ }, {
+ /* sentinel */
+ }
+};
+MODULE_DEVICE_TABLE(of, panel_simple_of_match);
+
+static int panel_simple_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *id;
+ struct device_node *backlight;
+ struct panel_simple *panel;
+ enum of_gpio_flags flags;
+ int err;
+
+ panel = devm_kzalloc(&pdev->dev, sizeof(*panel), GFP_KERNEL);
+ if (!panel)
+ return -ENOMEM;
+
+ id = of_match_node(panel_simple_of_match, pdev->dev.of_node);
+ if (!id)
+ return -ENODEV;
+
+ panel->desc = id->data;
+ panel->enabled = false;
+
+ panel->supply = devm_regulator_get(&pdev->dev, "power");
+ if (IS_ERR(panel->supply))
+ return PTR_ERR(panel->supply);
+
+ panel->enable_gpio = of_get_named_gpio_flags(pdev->dev.of_node,
+ "enable-gpios", 0,
+ &flags);
+ if (gpio_is_valid(panel->enable_gpio)) {
+ unsigned int value;
+
+ if (flags & OF_GPIO_ACTIVE_LOW)
+ panel->enable_gpio_flags |= GPIO_ACTIVE_LOW;
+
+ err = gpio_request(panel->enable_gpio, "enable");
+ if (err < 0) {
+ dev_err(&pdev->dev, "failed to request GPIO#%u: %d\n",
+ panel->enable_gpio, err);
+ return err;
+ }
+
+ value = (panel->enable_gpio_flags & GPIO_ACTIVE_LOW) != 0;
+
+ err = gpio_direction_output(panel->enable_gpio, value);
+ if (err < 0) {
+ dev_err(&pdev->dev, "failed to setup GPIO%u: %d\n",
+ panel->enable_gpio, err);
+ goto free_gpio;
+ }
+ }
+
+ backlight = of_parse_phandle(pdev->dev.of_node, "backlight", 0);
+ if (backlight) {
+ panel->backlight = of_find_backlight_by_node(backlight);
+ if (!panel->backlight) {
+ err = -EPROBE_DEFER;
+ goto free_gpio;
+ }
+
+ of_node_put(backlight);
+ }
+
+ drm_panel_init(&panel->base);
+ panel->base.dev = &pdev->dev;
+ panel->base.funcs = &panel_simple_funcs;
+
+ err = drm_panel_add(&panel->base);
+ if (err < 0)
+ goto free_gpio;
+
+ platform_set_drvdata(pdev, panel);
+
+ return 0;
+
+free_gpio:
+ if (gpio_is_valid(panel->enable_gpio))
+ gpio_free(panel->enable_gpio);
+
+ return err;
+}
+
+static int panel_simple_remove(struct platform_device *pdev)
+{
+ struct panel_simple *panel = platform_get_drvdata(pdev);
+
+ if (gpio_is_valid(panel->enable_gpio)) {
+ if (panel->enable_gpio_flags & GPIO_ACTIVE_LOW)
+ gpio_set_value(panel->enable_gpio, 1);
+ else
+ gpio_set_value(panel->enable_gpio, 0);
+
+ gpio_free(panel->enable_gpio);
+ }
+
+ regulator_disable(panel->supply);
+
+ if (panel->backlight)
+ put_device(&panel->backlight->dev);
+
+ drm_panel_detach(&panel->base);
+ drm_panel_remove(&panel->base);
+
+ return 0;
+}
+
+static struct platform_driver panel_simple_driver = {
+ .driver = {
+ .name = "panel-simple",
+ .owner = THIS_MODULE,
+ .of_match_table = panel_simple_of_match,
+ },
+ .probe = panel_simple_probe,
+ .remove = panel_simple_remove,
+};
+module_platform_driver(panel_simple_driver);
+
+MODULE_DESCRIPTION("DRM Driver for Simple Panels");
+MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>");
+MODULE_LICENSE("GPL v2");
Add a driver for simple panels. Such panels can have a regulator that provides the supply voltage and a separate GPIO to enable the panel. Optionally the panels can have a backlight associated with them so it can be enabled or disabled according to the panel's power management mode. Support is added for three panels: An AU Optronics 10.1" WSVGA, a Chunghwa Picture Tubes 10.1" WXGA and a Panasonic 10.1 WUXGA TFT LCD panel. Signed-off-by: Thierry Reding <treding@nvidia.com> --- Changes in v2: - update vendor prefixes (cptt -> chunghwa, pc -> panasonic) - split up panel binding documents per-panel - make regulator mandatory - add flag to keep track of enabled status .../devicetree/bindings/panel/auo,b101aw03.txt | 7 + .../bindings/panel/chunghwa,claa101wb03.txt | 7 + .../bindings/panel/panasonic,vvx10f004b00.txt | 7 + .../devicetree/bindings/panel/simple-panel.txt | 21 ++ drivers/gpu/drm/Makefile | 1 + drivers/gpu/drm/panel/Kconfig | 13 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-simple.c | 339 +++++++++++++++++++++ 8 files changed, 396 insertions(+) create mode 100644 Documentation/devicetree/bindings/panel/auo,b101aw03.txt create mode 100644 Documentation/devicetree/bindings/panel/chunghwa,claa101wb03.txt create mode 100644 Documentation/devicetree/bindings/panel/panasonic,vvx10f004b00.txt create mode 100644 Documentation/devicetree/bindings/panel/simple-panel.txt create mode 100644 drivers/gpu/drm/panel/Makefile create mode 100644 drivers/gpu/drm/panel/panel-simple.c