| Message ID | 1386339891-32717-10-git-send-email-sourav.poddar@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
* Sourav Poddar <sourav.poddar@ti.com> [131206 06:29]: > These add device tree entry for qspi controller driver on dra7. FYI these .dts changes need to be queued separately by Benoit and should be posted as a seprate series in general to avoid confusion. Regards, Tony > Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> > --- > v1->v2: > use "MUX_MODE1" instead of numeric value > arch/arm/boot/dts/dra7-evm.dts | 32 ++++++++++++++++++++++++++++++++ > arch/arm/boot/dts/dra7.dtsi | 13 +++++++++++++ > 2 files changed, 45 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts > index 5babba0..4a57fdf 100644 > --- a/arch/arm/boot/dts/dra7-evm.dts > +++ b/arch/arm/boot/dts/dra7-evm.dts > @@ -93,6 +93,21 @@ > 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ > >; > }; > + > + qspi1_pins: pinmux_qspi1_pins { > + pinctrl-single,pins = < > + 0x4c (PIN_INPUT | MUX_MODE1) /* gpmc_a3.qspi1_cs2 */ > + 0x50 (PIN_INPUT | MUX_MODE1) /* gpmc_a4.qspi1_cs3 */ > + 0x74 (PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ > + 0x78 (PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ > + 0x7c (PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ > + 0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ > + 0x84 (PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ > + 0x88 (PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ > + 0xb8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ > + 0xbc (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ > + >; > + }; > }; > > &i2c1 { > @@ -273,3 +288,20 @@ > &cpu0 { > cpu0-supply = <&smps123_reg>; > }; > + > +&qspi { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&qspi1_pins>; > + > + spi-max-frequency = <48000000>; > + m25p80@0 { > + compatible = "s25fl256s1"; > + spi-max-frequency = <48000000>; > + reg = <0>; > + spi-tx-bus-width = <1>; > + spi-rx-bus-width = <4>; > + spi-cpol; > + spi-cpha; > + }; > +}; > diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi > index 67275c8..b06d899 100644 > --- a/arch/arm/boot/dts/dra7.dtsi > +++ b/arch/arm/boot/dts/dra7.dtsi > @@ -582,6 +582,19 @@ > dma-names = "tx0", "rx0"; > status = "disabled"; > }; > + > + qspi: qspi@4b300000 { > + compatible = "ti,dra7xxx-qspi"; > + reg = <0x4b300000 0x100>, <0x4a002558 0x4>, > + <0x5c000000 0x3ffffff>; > + reg-names = "qspi_base", "qspi_ctrlmod", "qspi_mmap"; > + #address-cells = <1>; > + #size-cells = <0>; > + ti,hwmods = "qspi"; > + num-cs = <4>; > + interrupts = <0 124 0x4>; > + status = "disabled"; > + }; > }; > > clocks { > -- > 1.7.1 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Monday 09 December 2013 11:12 PM, Tony Lindgren wrote: > * Sourav Poddar<sourav.poddar@ti.com> [131206 06:29]: >> These add device tree entry for qspi controller driver on dra7. > FYI these .dts changes need to be queued separately by Benoit and > should be posted as a seprate series in general to avoid confusion. > Ok, thanks! I posted this for review along with other code changes. I will post them seperately to Benoit. > Regards, > > Tony > >> Signed-off-by: Sourav Poddar<sourav.poddar@ti.com> >> --- >> v1->v2: >> use "MUX_MODE1" instead of numeric value >> arch/arm/boot/dts/dra7-evm.dts | 32 ++++++++++++++++++++++++++++++++ >> arch/arm/boot/dts/dra7.dtsi | 13 +++++++++++++ >> 2 files changed, 45 insertions(+), 0 deletions(-) >> >> diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts >> index 5babba0..4a57fdf 100644 >> --- a/arch/arm/boot/dts/dra7-evm.dts >> +++ b/arch/arm/boot/dts/dra7-evm.dts >> @@ -93,6 +93,21 @@ >> 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ >> >; >> }; >> + >> + qspi1_pins: pinmux_qspi1_pins { >> + pinctrl-single,pins =< >> + 0x4c (PIN_INPUT | MUX_MODE1) /* gpmc_a3.qspi1_cs2 */ >> + 0x50 (PIN_INPUT | MUX_MODE1) /* gpmc_a4.qspi1_cs3 */ >> + 0x74 (PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ >> + 0x78 (PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ >> + 0x7c (PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ >> + 0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ >> + 0x84 (PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ >> + 0x88 (PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ >> + 0xb8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ >> + 0xbc (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ >> + >; >> + }; >> }; >> >> &i2c1 { >> @@ -273,3 +288,20 @@ >> &cpu0 { >> cpu0-supply =<&smps123_reg>; >> }; >> + >> +&qspi { >> + status = "okay"; >> + pinctrl-names = "default"; >> + pinctrl-0 =<&qspi1_pins>; >> + >> + spi-max-frequency =<48000000>; >> + m25p80@0 { >> + compatible = "s25fl256s1"; >> + spi-max-frequency =<48000000>; >> + reg =<0>; >> + spi-tx-bus-width =<1>; >> + spi-rx-bus-width =<4>; >> + spi-cpol; >> + spi-cpha; >> + }; >> +}; >> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi >> index 67275c8..b06d899 100644 >> --- a/arch/arm/boot/dts/dra7.dtsi >> +++ b/arch/arm/boot/dts/dra7.dtsi >> @@ -582,6 +582,19 @@ >> dma-names = "tx0", "rx0"; >> status = "disabled"; >> }; >> + >> + qspi: qspi@4b300000 { >> + compatible = "ti,dra7xxx-qspi"; >> + reg =<0x4b300000 0x100>,<0x4a002558 0x4>, >> + <0x5c000000 0x3ffffff>; >> + reg-names = "qspi_base", "qspi_ctrlmod", "qspi_mmap"; >> + #address-cells =<1>; >> + #size-cells =<0>; >> + ti,hwmods = "qspi"; >> + num-cs =<4>; >> + interrupts =<0 124 0x4>; >> + status = "disabled"; >> + }; >> }; >> >> clocks { >> -- >> 1.7.1 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-omap" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Dec 10, 2013 at 09:55:15AM +0530, Sourav Poddar wrote: > I posted this for review along with other code changes. > I will post them seperately to Benoit. Please wait until the driver updates have been reviewed.
On Tuesday 10 December 2013 04:01 PM, Mark Brown wrote: > On Tue, Dec 10, 2013 at 09:55:15AM +0530, Sourav Poddar wrote: > >> I posted this for review along with other code changes. >> I will post them seperately to Benoit. > Please wait until the driver updates have been reviewed. Ok. -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Mark, On Tuesday 10 December 2013 04:01 PM, Mark Brown wrote: > On Tue, Dec 10, 2013 at 09:55:15AM +0530, Sourav Poddar wrote: > >> I posted this for review along with other code changes. >> I will post them seperately to Benoit. > Please wait until the driver updates have been reviewed. I was thinking of sending this dts patches seperately to benoit, so that we can enable atleast 1/4 bit mode for our controller. Anyways, there is no memory mapped specific binding used. Once, we get our driver updates reviewed and *if* there is anything memory mapped specific added, I can send them as a seperate patch. Anyways with spi nor framework in sight the driver uodates can go anyewhere and might take some time. . Does this sound Ok to you? -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 5babba0..4a57fdf 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -93,6 +93,21 @@ 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ >; }; + + qspi1_pins: pinmux_qspi1_pins { + pinctrl-single,pins = < + 0x4c (PIN_INPUT | MUX_MODE1) /* gpmc_a3.qspi1_cs2 */ + 0x50 (PIN_INPUT | MUX_MODE1) /* gpmc_a4.qspi1_cs3 */ + 0x74 (PIN_INPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ + 0x78 (PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ + 0x7c (PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ + 0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ + 0x84 (PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ + 0x88 (PIN_INPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ + 0xb8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ + 0xbc (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs3.qspi1_cs1 */ + >; + }; }; &i2c1 { @@ -273,3 +288,20 @@ &cpu0 { cpu0-supply = <&smps123_reg>; }; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi1_pins>; + + spi-max-frequency = <48000000>; + m25p80@0 { + compatible = "s25fl256s1"; + spi-max-frequency = <48000000>; + reg = <0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-cpol; + spi-cpha; + }; +}; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 67275c8..b06d899 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -582,6 +582,19 @@ dma-names = "tx0", "rx0"; status = "disabled"; }; + + qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>, <0x4a002558 0x4>, + <0x5c000000 0x3ffffff>; + reg-names = "qspi_base", "qspi_ctrlmod", "qspi_mmap"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "qspi"; + num-cs = <4>; + interrupts = <0 124 0x4>; + status = "disabled"; + }; }; clocks {
These add device tree entry for qspi controller driver on dra7. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> --- v1->v2: use "MUX_MODE1" instead of numeric value arch/arm/boot/dts/dra7-evm.dts | 32 ++++++++++++++++++++++++++++++++ arch/arm/boot/dts/dra7.dtsi | 13 +++++++++++++ 2 files changed, 45 insertions(+), 0 deletions(-)