@@ -149,6 +149,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6dl-gw53xx.dtb \
imx6dl-gw54xx.dtb \
imx6dl-sabreauto.dtb \
+ imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-wandboard.dtb \
imx6q-arm2.dtb \
new file mode 100644
@@ -0,0 +1,20 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-sabrelite.dtsi"
+
+/ {
+ model = "Freescale i.MX6 DualLite SABRE Lite Board";
+ compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl";
+};
@@ -12,225 +12,13 @@
/dts-v1/;
#include "imx6q.dtsi"
+#include "imx6qdl-sabrelite.dtsi"
/ {
model = "Freescale i.MX6 Quad SABRE Lite Board";
compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
-
- memory {
- reg = <0x10000000 0x40000000>;
- };
-
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_2p5v: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "2P5V";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-always-on;
- };
-
- reg_3p3v: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_usb_otg_vbus: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "usb_otg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
- enable-active-high;
- };
- };
-
- sound {
- compatible = "fsl,imx6q-sabrelite-sgtl5000",
- "fsl,imx-audio-sgtl5000";
- model = "imx6q-sabrelite-sgtl5000";
- ssi-controller = <&ssi1>;
- audio-codec = <&codec>;
- audio-routing =
- "MIC_IN", "Mic Jack",
- "Mic Jack", "Mic Bias",
- "Headphone Jack", "HP_OUT";
- mux-int-port = <1>;
- mux-ext-port = <4>;
- };
-};
-
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-};
-
-&ecspi1 {
- fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio3 19 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash: m25p80@0 {
- compatible = "sst,sst25vf016b";
- spi-max-frequency = <20000000>;
- reg = <0>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
- phy-reset-gpios = <&gpio3 23 0>;
- status = "okay";
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-
- codec: sgtl5000@0a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- clocks = <&clks 201>;
- VDDA-supply = <®_2p5v>;
- VDDIO-supply = <®_3p3v>;
- };
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- imx6q-sabrelite {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x80000000
- MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x80000000
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000
- MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x80000000
- MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0
- MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x80000000
- >;
- };
-
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <MX6QDL_AUDMUX_PINGRP1>;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <MX6QDL_ECSPI1_PINGRP1>;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <MX6QDL_ENET_PINGRP1>;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <MX6QDL_I2C1_PINGRP1>;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <MX6QDL_UART2_PINGRP1>;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <MX6QDL_USBOTG_PINGRP1>;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <MX6QDL_USDHC3_PINGRP_D4>;
- };
-
- pinctrl_usdhc4: usdhc4grp {
- fsl,pins = <MX6QDL_USDHC4_PINGRP_D4>;
- };
- };
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel@0 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "okay";
-
- display-timings {
- native-mode = <&timing0>;
- timing0: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- };
- };
- };
};
&sata {
status = "okay";
};
-
-&ssi1 {
- fsl,mode = "i2s-slave";
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&usbh1 {
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- disable-over-current;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 0>;
- wp-gpios = <&gpio7 1 0>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
-};
-
-&usdhc4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc4>;
- cd-gpios = <&gpio2 6 0>;
- wp-gpios = <&gpio2 7 0>;
- vmmc-supply = <®_3p3v>;
- status = "okay";
-};
similarity index 96%
copy from arch/arm/boot/dts/imx6q-sabrelite.dts
copy to arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -10,13 +10,7 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/dts-v1/;
-#include "imx6q.dtsi"
-
/ {
- model = "Freescale i.MX6 Quad SABRE Lite Board";
- compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
-
memory {
reg = <0x10000000 0x40000000>;
};
@@ -190,10 +184,6 @@
};
};
-&sata {
- status = "okay";
-};
-
&ssi1 {
fsl,mode = "i2s-slave";
status = "okay";
This makes the structure of Sabre Lite board files the same as Sabre SD board files so that they are easier to compare. By this, I mean that the majority of the file imx6q-sabrelite.dts is moved to imx6qdl-sabrelite.dtsi so that both imx6q-sabrelite.dts and imx6dl-sabrelite.dts can include it. Now Sabre Lite has support for Dual Lite/Solo processors. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-sabrelite.dts | 20 ++ arch/arm/boot/dts/imx6q-sabrelite.dts | 214 +-------------------- ...{imx6q-sabrelite.dts => imx6qdl-sabrelite.dtsi} | 10 - 4 files changed, 22 insertions(+), 223 deletions(-) create mode 100644 arch/arm/boot/dts/imx6dl-sabrelite.dts copy arch/arm/boot/dts/{imx6q-sabrelite.dts => imx6qdl-sabrelite.dtsi} (96%)