[v5,1/2] dmaengine: add Qualcomm BAM dma driver

Message ID	1391546556-27702-2-git-send-email-agross@codeaurora.org (mailing list archive)
State	New, archived
Headers	show Return-Path: <linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org> sender: agross@smtp.codeaurora.org) by smtp.codeaurora.org (Postfix) with ESMTPSA id 1F01313F001; Tue, 4 Feb 2014 20:42:46 +0000 (UTC) From: Andy Gross <agross@codeaurora.org> To: Vinod Koul <vinod.koul@intel.com>, Dan Williams <dan.j.williams@intel.com>, dmaengine@vger.kernel.org Subject: [Patch v5 1/2] dmaengine: add Qualcomm BAM dma driver Date: Tue, 4 Feb 2014 14:42:35 -0600 Message-Id: <1391546556-27702-2-git-send-email-agross@codeaurora.org> In-Reply-To: <1391546556-27702-1-git-send-email-agross@codeaurora.org> References: <1391546556-27702-1-git-send-email-agross@codeaurora.org> Cc: devicetree@vger.kernel.org, Andy Gross <agross@codeaurora.org>, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-arm-msm@vger.kernel.org Precedence: list MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "linux-arm-kernel" <linux-arm-kernel-bounces@lists.infradead.org> Errors-To: linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org

On Tue, Feb 04, 2014 at 02:42:35PM -0600, Andy Gross wrote: > Add the DMA engine driver for the QCOM Bus Access Manager (BAM) DMA controller > found in the MSM 8x74 platforms. > > Each BAM DMA device is associated with a specific on-chip peripheral. Each > channel provides a uni-directional data transfer engine that is capable of > transferring data between the peripheral and system memory (System mode), or > between two peripherals (BAM2BAM). > > The initial release of this driver only supports slave transfers between > peripherals and system memory. > > Signed-off-by: Andy Gross <agross@codeaurora.org> > +++ b/drivers/dma/qcom_bam_dma.c > @@ -0,0 +1,1066 @@ > +/* > + * QCOM BAM DMA engine driver > + * > + * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. This is bit strange, usually copyright is retained by your employer, but I am fine with it :) > +struct bam_desc_hw { > + u32 addr; /* Buffer physical address */ this is where we might have an issue. Is this the DMA register which is 32bit wide or you are descibing it so. Will this work if you are in 64 bit? > + u16 size; /* Buffer size in bytes */ > + u16 flags; > +}; > + > +/** > + * bam_reset_channel - Reset individual BAM DMA channel > + * @bchan: bam channel > + * > + * This function resets a specific BAM channel > + */ > +static void bam_reset_channel(struct bam_chan *bchan) > +{ > + struct bam_device *bdev = bchan->bdev; > + > + /* reset channel */ > + writel_relaxed(1, bdev->regs + BAM_P_RST(bchan->id)); > + writel_relaxed(0, bdev->regs + BAM_P_RST(bchan->id)); > + > + /* don't allow reorder of the channel reset */ > + wmb(); Documentation/memory-barriers.txt describes wmb() as a CPU barier but based on above you want it to be a compiler barrier then you should do 1st write, barrier(), second write. > + > + /* make sure hw is initialized when channel is used the first time */ > + bchan->initialized = 0; > +} okay why no locks held while reset? > + > +/** > + * bam_chan_init_hw - Initialize channel hardware > + * @bchan: bam channel > + * > + * This function resets and initializes the BAM channel > + */ > +static void bam_chan_init_hw(struct bam_chan *bchan, > + enum dma_transfer_direction dir) > +{ > + struct bam_device *bdev = bchan->bdev; > + u32 val; > + > + /* Reset the channel to clear internal state of the FIFO */ > + bam_reset_channel(bchan); > + > + /* > + * write out 8 byte aligned address. We have enough space for this > + * because we allocated 1 more descriptor (8 bytes) than we can use > + */ > + writel_relaxed(ALIGN(bchan->fifo_phys, sizeof(struct bam_desc_hw)), > + bdev->regs + BAM_P_DESC_FIFO_ADDR(bchan->id)); > + writel_relaxed(BAM_DESC_FIFO_SIZE, bdev->regs + > + BAM_P_FIFO_SIZES(bchan->id)); > + > + /* enable the per pipe interrupts, enable EOT, ERR, and INT irqs */ > + writel_relaxed(P_DEFAULT_IRQS_EN, bdev->regs + BAM_P_IRQ_EN(bchan->id)); > + > + /* unmask the specific pipe and EE combo */ > + val = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); > + val |= BIT(bchan->id); > + writel_relaxed(val, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); > + > + /* set fixed direction and mode, then enable channel */ > + val = P_EN | P_SYS_MODE; > + if (dir == DMA_DEV_TO_MEM) > + val |= P_DIRECTION; > + > + /* make sure the other stores occur before enabling channel */ > + wmb(); here again! > + writel_relaxed(val, bdev->regs + BAM_P_CTRL(bchan->id)); > + > + bchan->initialized = 1; > + > + /* init FIFO pointers */ > + bchan->head = 0; > + bchan->tail = 0; > +} > + > +/** > + * bam_alloc_chan - Allocate channel resources for DMA channel. > + * @chan: specified channel > + * > + * This function allocates the FIFO descriptor memory > + */ > +static int bam_alloc_chan(struct dma_chan *chan) > +{ > + struct bam_chan *bchan = to_bam_chan(chan); > + struct bam_device *bdev = bchan->bdev; > + > + /* allocate FIFO descriptor space, but only if necessary */ > + if (!bchan->fifo_virt) { > + bchan->fifo_virt = dma_alloc_writecombine(bdev->dev, > + BAM_DESC_FIFO_SIZE, &bchan->fifo_phys, > + GFP_KERNEL); > + > + if (!bchan->fifo_virt) { > + dev_err(bdev->dev, "Failed to allocate desc fifo\n"); > + return -ENOMEM; > + } > + } > + > + return BAM_DESC_FIFO_SIZE; But you cna have SW descriptors more than HW ones and issue new ones once HW is done with them. Why tie the limit to what HW supports and not create a better driver? > + > +/** > + * bam_slave_config - set slave configuration for channel > + * @chan: dma channel > + * @cfg: slave configuration > + * > + * Sets slave configuration for channel > + * > + */ > +static void bam_slave_config(struct bam_chan *bchan, > + struct dma_slave_config *cfg) > +{ > + struct bam_device *bdev = bchan->bdev; > + u32 maxburst; > + > + if (bchan->slave.direction == DMA_DEV_TO_MEM) > + maxburst = bchan->slave.src_maxburst = cfg->src_maxburst; > + else > + maxburst = bchan->slave.dst_maxburst = cfg->dst_maxburst; can you remove usage of slave.direction have save both. I am going to remove this member... > + > + /* set desc threshold */ > + writel_relaxed(maxburst, bdev->regs + BAM_DESC_CNT_TRSHLD); > +} > + > +/** > + * bam_prep_slave_sg - Prep slave sg transaction > + * > + * @chan: dma channel > + * @sgl: scatter gather list > + * @sg_len: length of sg > + * @direction: DMA transfer direction > + * @flags: DMA flags > + * @context: transfer context (unused) > + */ > +static struct dma_async_tx_descriptor *bam_prep_slave_sg(struct dma_chan *chan, > + struct scatterlist *sgl, unsigned int sg_len, > + enum dma_transfer_direction direction, unsigned long flags, > + void *context) > +{ > + struct bam_chan *bchan = to_bam_chan(chan); > + struct bam_device *bdev = bchan->bdev; > + struct bam_async_desc *async_desc; > + struct scatterlist *sg; > + u32 i; > + struct bam_desc_hw *desc; > + > + > + if (!is_slave_direction(direction)) { > + dev_err(bdev->dev, "invalid dma direction\n"); > + return NULL; > + } > + > + > + /* allocate enough room to accomodate the number of entries */ > + async_desc = kzalloc(sizeof(*async_desc) + > + (sg_len * sizeof(struct bam_desc_hw)), GFP_NOWAIT); this seems to assume that each sg entry length will not exceed the HW capablity. Does engine support any length descriptor, if not you may want to split to multiple. > + > + if (!async_desc) { > + dev_err(bdev->dev, "failed to allocate async descriptor\n"); > + goto err_out; > + } > + > + async_desc->num_desc = sg_len; > + async_desc->curr_desc = async_desc->desc; > + async_desc->dir = direction; > + > + /* fill in descriptors, align hw descriptor to 8 bytes */ > + desc = async_desc->desc; > + for_each_sg(sgl, sg, sg_len, i) { > + if (sg_dma_len(sg) > BAM_MAX_DATA_SIZE) { > + dev_err(bdev->dev, "segment exceeds max size\n"); > + goto err_out; gottcha, okay why not split here to multiple descriptors with max size all but last? > + } > + > + desc->addr = sg_dma_address(sg); > + desc->size = sg_dma_len(sg); > + async_desc->length += sg_dma_len(sg); > + desc++; > + } > + > + return vchan_tx_prep(&bchan->vc, &async_desc->vd, flags); > + > +err_out: > + kfree(async_desc); > + return NULL; > +} > + > +/** > + * bam_dma_terminate_all - terminate all transactions on a channel > + * @bchan: bam dma channel > + * > + * Dequeues and frees all transactions > + * No callbacks are done > + * > + */ > +static void bam_dma_terminate_all(struct bam_chan *bchan) > +{ > + unsigned long flag; > + LIST_HEAD(head); > + > + /* remove all transactions, including active transaction */ > + spin_lock_irqsave(&bchan->vc.lock, flag); > + if (bchan->curr_txd) { > + list_add(&bchan->curr_txd->vd.node, &bchan->vc.desc_issued); > + bchan->curr_txd = NULL; > + } > + > + vchan_get_all_descriptors(&bchan->vc, &head); > + spin_unlock_irqrestore(&bchan->vc.lock, flag); > + > + vchan_dma_desc_free_list(&bchan->vc, &head); why drop the lock here, i dont think this one needs to be called with lock dropped, didnt see it garbbing. > +} > + > +/** > + * bam_control - DMA device control > + * @chan: dma channel > + * @cmd: control cmd > + * @arg: cmd argument > + * > + * Perform DMA control command > + * > + */ > +static int bam_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd, > + unsigned long arg) > +{ > + struct bam_chan *bchan = to_bam_chan(chan); > + struct bam_device *bdev = bchan->bdev; > + int ret = 0; > + unsigned long flag; > + > + switch (cmd) { > + case DMA_PAUSE: > + spin_lock_irqsave(&bchan->vc.lock, flag); > + writel_relaxed(1, bdev->regs + BAM_P_HALT(bchan->id)); > + bchan->paused = 1; > + spin_unlock_irqrestore(&bchan->vc.lock, flag); > + break; > + case DMA_RESUME: > + spin_lock_irqsave(&bchan->vc.lock, flag); > + writel_relaxed(0, bdev->regs + BAM_P_HALT(bchan->id)); > + bchan->paused = 0; > + spin_unlock_irqrestore(&bchan->vc.lock, flag); > + break; > + case DMA_TERMINATE_ALL: > + bam_dma_terminate_all(bchan); > + break; > + case DMA_SLAVE_CONFIG: > + bam_slave_config(bchan, (struct dma_slave_config *)arg); > + break; > + default: > + ret = -ENXIO; > + break; > + } empty line after each break would be appreciated. > + > + return ret; > +} > + > +/** > + * bam_start_dma - start next transaction > + * @bchan - bam dma channel > + * > + * Note: must hold bam dma channel vc.lock > + */ > +static void bam_start_dma(struct bam_chan *bchan) > +{ > + struct virt_dma_desc *vd = vchan_next_desc(&bchan->vc); > + struct bam_device *bdev = bchan->bdev; > + struct bam_async_desc *async_desc; > + struct bam_desc_hw *desc; > + struct bam_desc_hw *fifo = PTR_ALIGN(bchan->fifo_virt, > + sizeof(struct bam_desc_hw)); > + > + if (!vd) > + return; > + > + list_del(&vd->node); > + > + async_desc = container_of(vd, struct bam_async_desc, vd); > + bchan->curr_txd = async_desc; > + > + /* on first use, initialize the channel hardware */ > + if (!bchan->initialized) > + bam_chan_init_hw(bchan, async_desc->dir); > + > + > + desc = bchan->curr_txd->curr_desc; > + > + if (async_desc->num_desc > MAX_DESCRIPTORS) > + async_desc->xfer_len = MAX_DESCRIPTORS; > + else > + async_desc->xfer_len = async_desc->num_desc; > + > + /* set INT on last descriptor */ > + desc[async_desc->xfer_len - 1].flags |= DESC_FLAG_INT; > + > + if (bchan->tail + async_desc->xfer_len > MAX_DESCRIPTORS) { > + u32 partial = MAX_DESCRIPTORS - bchan->tail; > + > + memcpy(&fifo[bchan->tail], desc, > + partial * sizeof(struct bam_desc_hw)); > + memcpy(fifo, &desc[partial], (async_desc->xfer_len - partial) * > + sizeof(struct bam_desc_hw)); > + } else { > + memcpy(&fifo[bchan->tail], desc, > + async_desc->xfer_len * sizeof(struct bam_desc_hw)); where is the destination memeory located, device or system memory. I think later, right? > + } > + > + bchan->tail += async_desc->xfer_len; > + bchan->tail %= MAX_DESCRIPTORS; > + > + /* ensure descriptor writes and dma start not reordered */ > + wmb(); > + writel_relaxed(bchan->tail * sizeof(struct bam_desc_hw), > + bdev->regs + BAM_P_EVNT_REG(bchan->id)); > +} > + Overall driver loooks fine mostly with few comments as above. And yes for 2nd patch, would need someone to ACK it before we can appply this

diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index c10eb89..1b2f6cf 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -386,4 +386,13 @@ config DMATEST config DMA_ENGINE_RAID bool +config QCOM_BAM_DMA + tristate "QCOM BAM DMA support" + depends on ARCH_MSM_DT || (COMPILE_TEST && OF && ARM) + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + ---help--- + Enable support for the QCOM BAM DMA controller. This controller + provides DMA capabilities for a variety of on-chip devices. + endif diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile index 0ce2da9..7ef950a 100644 --- a/drivers/dma/Makefile +++ b/drivers/dma/Makefile @@ -42,3 +42,4 @@ obj-$(CONFIG_MMP_PDMA) += mmp_pdma.o obj-$(CONFIG_DMA_JZ4740) += dma-jz4740.o obj-$(CONFIG_TI_CPPI41) += cppi41.o obj-$(CONFIG_K3_DMA) += k3dma.o +obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o diff --git a/drivers/dma/qcom_bam_dma.c b/drivers/dma/qcom_bam_dma.c new file mode 100644 index 0000000..214250c --- /dev/null +++ b/drivers/dma/qcom_bam_dma.c @@ -0,0 +1,1066 @@ +/* + * QCOM BAM DMA engine driver + * + * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * + * QCOM BAM DMA blocks are distributed amongst a number of the on-chip + * peripherals on the MSM 8x74. The configuration of the channels are dependent + * on the way they are hard wired to that specific peripheral. The peripheral + * device tree entries specify the configuration of each channel. + * + * The DMA controller requires the use of external memory for storage of the + * hardware descriptors for each channel. The descriptor FIFO is accessed as a + * circular buffer and operations are managed according to the offset within the + * FIFO. After pipe/channel reset, all of the pipe registers and internal state + * are back to defaults. + * + * During DMA operations, we write descriptors to the FIFO, being careful to + * handle wrapping and then write the last FIFO offset to that channel's + * P_EVNT_REG register to kick off the transaction. The P_SW_OFSTS register + * indicates the current FIFO offset that is being processed, so there is some + * indication of where the hardware is currently working. + */ + +#include <linux/kernel.h> +#include <linux/io.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> +#include <linux/scatterlist.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_dma.h> +#include <linux/clk.h> +#include <linux/dmaengine.h> + +#include "dmaengine.h" +#include "virt-dma.h" + +struct bam_desc_hw { + u32 addr; /* Buffer physical address */ + u16 size; /* Buffer size in bytes */ + u16 flags; +}; + +#define DESC_FLAG_INT BIT(15) +#define DESC_FLAG_EOT BIT(14) +#define DESC_FLAG_EOB BIT(13) + +struct bam_async_desc { + struct virt_dma_desc vd; + + u32 num_desc; + u32 xfer_len; + struct bam_desc_hw *curr_desc; + + enum dma_transfer_direction dir; + size_t length; + struct bam_desc_hw desc[0]; +}; + +#define BAM_CTRL 0x0000 +#define BAM_REVISION 0x0004 +#define BAM_SW_REVISION 0x0080 +#define BAM_NUM_PIPES 0x003C +#define BAM_TIMER 0x0040 +#define BAM_TIMER_CTRL 0x0044 +#define BAM_DESC_CNT_TRSHLD 0x0008 +#define BAM_IRQ_SRCS 0x000C +#define BAM_IRQ_SRCS_MSK 0x0010 +#define BAM_IRQ_SRCS_UNMASKED 0x0030 +#define BAM_IRQ_STTS 0x0014 +#define BAM_IRQ_CLR 0x0018 +#define BAM_IRQ_EN 0x001C +#define BAM_CNFG_BITS 0x007C +#define BAM_IRQ_SRCS_EE(pipe) (0x0800 + ((pipe) * 0x80)) +#define BAM_IRQ_SRCS_MSK_EE(pipe) (0x0804 + ((pipe) * 0x80)) +#define BAM_P_CTRL(pipe) (0x1000 + ((pipe) * 0x1000)) +#define BAM_P_RST(pipe) (0x1004 + ((pipe) * 0x1000)) +#define BAM_P_HALT(pipe) (0x1008 + ((pipe) * 0x1000)) +#define BAM_P_IRQ_STTS(pipe) (0x1010 + ((pipe) * 0x1000)) +#define BAM_P_IRQ_CLR(pipe) (0x1014 + ((pipe) * 0x1000)) +#define BAM_P_IRQ_EN(pipe) (0x1018 + ((pipe) * 0x1000)) +#define BAM_P_EVNT_DEST_ADDR(pipe) (0x182C + ((pipe) * 0x1000)) +#define BAM_P_EVNT_REG(pipe) (0x1818 + ((pipe) * 0x1000)) +#define BAM_P_SW_OFSTS(pipe) (0x1800 + ((pipe) * 0x1000)) +#define BAM_P_DATA_FIFO_ADDR(pipe) (0x1824 + ((pipe) * 0x1000)) +#define BAM_P_DESC_FIFO_ADDR(pipe) (0x181C + ((pipe) * 0x1000)) +#define BAM_P_EVNT_TRSHLD(pipe) (0x1828 + ((pipe) * 0x1000)) +#define BAM_P_FIFO_SIZES(pipe) (0x1820 + ((pipe) * 0x1000)) + +/* BAM CTRL */ +#define BAM_SW_RST BIT(0) +#define BAM_EN BIT(1) +#define BAM_EN_ACCUM BIT(4) +#define BAM_TESTBUS_SEL_SHIFT 5 +#define BAM_TESTBUS_SEL_MASK 0x3F +#define BAM_DESC_CACHE_SEL_SHIFT 13 +#define BAM_DESC_CACHE_SEL_MASK 0x3 +#define BAM_CACHED_DESC_STORE BIT(15) +#define IBC_DISABLE BIT(16) + +/* BAM REVISION */ +#define REVISION_SHIFT 0 +#define REVISION_MASK 0xFF +#define NUM_EES_SHIFT 8 +#define NUM_EES_MASK 0xF +#define CE_BUFFER_SIZE BIT(13) +#define AXI_ACTIVE BIT(14) +#define USE_VMIDMT BIT(15) +#define SECURED BIT(16) +#define BAM_HAS_NO_BYPASS BIT(17) +#define HIGH_FREQUENCY_BAM BIT(18) +#define INACTIV_TMRS_EXST BIT(19) +#define NUM_INACTIV_TMRS BIT(20) +#define DESC_CACHE_DEPTH_SHIFT 21 +#define DESC_CACHE_DEPTH_1 (0 << DESC_CACHE_DEPTH_SHIFT) +#define DESC_CACHE_DEPTH_2 (1 << DESC_CACHE_DEPTH_SHIFT) +#define DESC_CACHE_DEPTH_3 (2 << DESC_CACHE_DEPTH_SHIFT) +#define DESC_CACHE_DEPTH_4 (3 << DESC_CACHE_DEPTH_SHIFT) +#define CMD_DESC_EN BIT(23) +#define INACTIV_TMR_BASE_SHIFT 24 +#define INACTIV_TMR_BASE_MASK 0xFF + +/* BAM NUM PIPES */ +#define BAM_NUM_PIPES_SHIFT 0 +#define BAM_NUM_PIPES_MASK 0xFF +#define PERIPH_NON_PIPE_GRP_SHIFT 16 +#define PERIPH_NON_PIP_GRP_MASK 0xFF +#define BAM_NON_PIPE_GRP_SHIFT 24 +#define BAM_NON_PIPE_GRP_MASK 0xFF + +/* BAM CNFG BITS */ +#define BAM_PIPE_CNFG BIT(2) +#define BAM_FULL_PIPE BIT(11) +#define BAM_NO_EXT_P_RST BIT(12) +#define BAM_IBC_DISABLE BIT(13) +#define BAM_SB_CLK_REQ BIT(14) +#define BAM_PSM_CSW_REQ BIT(15) +#define BAM_PSM_P_RES BIT(16) +#define BAM_AU_P_RES BIT(17) +#define BAM_SI_P_RES BIT(18) +#define BAM_WB_P_RES BIT(19) +#define BAM_WB_BLK_CSW BIT(20) +#define BAM_WB_CSW_ACK_IDL BIT(21) +#define BAM_WB_RETR_SVPNT BIT(22) +#define BAM_WB_DSC_AVL_P_RST BIT(23) +#define BAM_REG_P_EN BIT(24) +#define BAM_PSM_P_HD_DATA BIT(25) +#define BAM_AU_ACCUMED BIT(26) +#define BAM_CMD_ENABLE BIT(27) + +#define BAM_CNFG_BITS_DEFAULT (BAM_PIPE_CNFG | \ + BAM_NO_EXT_P_RST | \ + BAM_IBC_DISABLE | \ + BAM_SB_CLK_REQ | \ + BAM_PSM_CSW_REQ | \ + BAM_PSM_P_RES | \ + BAM_AU_P_RES | \ + BAM_SI_P_RES | \ + BAM_WB_P_RES | \ + BAM_WB_BLK_CSW | \ + BAM_WB_CSW_ACK_IDL | \ + BAM_WB_RETR_SVPNT | \ + BAM_WB_DSC_AVL_P_RST | \ + BAM_REG_P_EN | \ + BAM_PSM_P_HD_DATA | \ + BAM_AU_ACCUMED | \ + BAM_CMD_ENABLE) + +/* PIPE CTRL */ +#define P_EN BIT(1) +#define P_DIRECTION BIT(3) +#define P_SYS_STRM BIT(4) +#define P_SYS_MODE BIT(5) +#define P_AUTO_EOB BIT(6) +#define P_AUTO_EOB_SEL_SHIFT 7 +#define P_AUTO_EOB_SEL_512 (0 << P_AUTO_EOB_SEL_SHIFT) +#define P_AUTO_EOB_SEL_256 (1 << P_AUTO_EOB_SEL_SHIFT) +#define P_AUTO_EOB_SEL_128 (2 << P_AUTO_EOB_SEL_SHIFT) +#define P_AUTO_EOB_SEL_64 (3 << P_AUTO_EOB_SEL_SHIFT) +#define P_PREFETCH_LIMIT_SHIFT 9 +#define P_PREFETCH_LIMIT_32 (0 << P_PREFETCH_LIMIT_SHIFT) +#define P_PREFETCH_LIMIT_16 (1 << P_PREFETCH_LIMIT_SHIFT) +#define P_PREFETCH_LIMIT_4 (2 << P_PREFETCH_LIMIT_SHIFT) +#define P_WRITE_NWD BIT(11) +#define P_LOCK_GROUP_SHIFT 16 +#define P_LOCK_GROUP_MASK 0x1F + +/* BAM_DESC_CNT_TRSHLD */ +#define CNT_TRSHLD 0xffff +#define DEFAULT_CNT_THRSHLD 0x4 + +/* BAM_IRQ_SRCS */ +#define BAM_IRQ BIT(31) +#define P_IRQ 0x7fffffff + +/* BAM_IRQ_SRCS_MSK */ +#define BAM_IRQ_MSK BAM_IRQ +#define P_IRQ_MSK P_IRQ + +/* BAM_IRQ_STTS */ +#define BAM_TIMER_IRQ BIT(4) +#define BAM_EMPTY_IRQ BIT(3) +#define BAM_ERROR_IRQ BIT(2) +#define BAM_HRESP_ERR_IRQ BIT(1) + +/* BAM_IRQ_CLR */ +#define BAM_TIMER_CLR BIT(4) +#define BAM_EMPTY_CLR BIT(3) +#define BAM_ERROR_CLR BIT(2) +#define BAM_HRESP_ERR_CLR BIT(1) + +/* BAM_IRQ_EN */ +#define BAM_TIMER_EN BIT(4) +#define BAM_EMPTY_EN BIT(3) +#define BAM_ERROR_EN BIT(2) +#define BAM_HRESP_ERR_EN BIT(1) + +/* BAM_P_IRQ_EN */ +#define P_PRCSD_DESC_EN BIT(0) +#define P_TIMER_EN BIT(1) +#define P_WAKE_EN BIT(2) +#define P_OUT_OF_DESC_EN BIT(3) +#define P_ERR_EN BIT(4) +#define P_TRNSFR_END_EN BIT(5) +#define P_DEFAULT_IRQS_EN (P_PRCSD_DESC_EN | P_ERR_EN | P_TRNSFR_END_EN) + +/* BAM_P_SW_OFSTS */ +#define P_SW_OFSTS_MASK 0xffff + +#define BAM_DESC_FIFO_SIZE SZ_32K +#define MAX_DESCRIPTORS (BAM_DESC_FIFO_SIZE / sizeof(struct bam_desc_hw) - 1) +#define BAM_MAX_DATA_SIZE (SZ_32K - 8) + +struct bam_chan { + struct virt_dma_chan vc; + + struct bam_device *bdev; + + /* configuration from device tree */ + u32 id; + u32 ee; + + struct bam_async_desc *curr_txd; /* current running dma */ + + /* runtime configuration */ + struct dma_slave_config slave; + + /* fifo storage */ + struct bam_desc_hw *fifo_virt; + dma_addr_t fifo_phys; + + /* fifo markers */ + unsigned short head; /* start of active descriptor entries */ + unsigned short tail; /* end of active descriptor entries */ + + unsigned int initialized; /* is the channel hw initialized? */ + unsigned int paused; /* is the channel paused? */ + + struct list_head node; +}; + +static inline struct bam_chan *to_bam_chan(struct dma_chan *common) +{ + return container_of(common, struct bam_chan, vc.chan); +} + +struct bam_device { + void __iomem *regs; + struct device *dev; + struct dma_device common; + struct device_dma_parameters dma_parms; + struct bam_chan *channels; + u32 num_channels; + + /* execution environment ID, from DT */ + u32 ee; + + struct clk *bamclk; + int irq; + + /* dma start transaction tasklet */ + struct tasklet_struct task; +}; + +/** + * bam_reset_channel - Reset individual BAM DMA channel + * @bchan: bam channel + * + * This function resets a specific BAM channel + */ +static void bam_reset_channel(struct bam_chan *bchan) +{ + struct bam_device *bdev = bchan->bdev; + + /* reset channel */ + writel_relaxed(1, bdev->regs + BAM_P_RST(bchan->id)); + writel_relaxed(0, bdev->regs + BAM_P_RST(bchan->id)); + + /* don't allow reorder of the channel reset */ + wmb(); + + /* make sure hw is initialized when channel is used the first time */ + bchan->initialized = 0; +} + +/** + * bam_chan_init_hw - Initialize channel hardware + * @bchan: bam channel + * + * This function resets and initializes the BAM channel + */ +static void bam_chan_init_hw(struct bam_chan *bchan, + enum dma_transfer_direction dir) +{ + struct bam_device *bdev = bchan->bdev; + u32 val; + + /* Reset the channel to clear internal state of the FIFO */ + bam_reset_channel(bchan); + + /* + * write out 8 byte aligned address. We have enough space for this + * because we allocated 1 more descriptor (8 bytes) than we can use + */ + writel_relaxed(ALIGN(bchan->fifo_phys, sizeof(struct bam_desc_hw)), + bdev->regs + BAM_P_DESC_FIFO_ADDR(bchan->id)); + writel_relaxed(BAM_DESC_FIFO_SIZE, bdev->regs + + BAM_P_FIFO_SIZES(bchan->id)); + + /* enable the per pipe interrupts, enable EOT, ERR, and INT irqs */ + writel_relaxed(P_DEFAULT_IRQS_EN, bdev->regs + BAM_P_IRQ_EN(bchan->id)); + + /* unmask the specific pipe and EE combo */ + val = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); + val |= BIT(bchan->id); + writel_relaxed(val, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); + + /* set fixed direction and mode, then enable channel */ + val = P_EN | P_SYS_MODE; + if (dir == DMA_DEV_TO_MEM) + val |= P_DIRECTION; + + /* make sure the other stores occur before enabling channel */ + wmb(); + writel_relaxed(val, bdev->regs + BAM_P_CTRL(bchan->id)); + + bchan->initialized = 1; + + /* init FIFO pointers */ + bchan->head = 0; + bchan->tail = 0; +} + +/** + * bam_alloc_chan - Allocate channel resources for DMA channel. + * @chan: specified channel + * + * This function allocates the FIFO descriptor memory + */ +static int bam_alloc_chan(struct dma_chan *chan) +{ + struct bam_chan *bchan = to_bam_chan(chan); + struct bam_device *bdev = bchan->bdev; + + /* allocate FIFO descriptor space, but only if necessary */ + if (!bchan->fifo_virt) { + bchan->fifo_virt = dma_alloc_writecombine(bdev->dev, + BAM_DESC_FIFO_SIZE, &bchan->fifo_phys, + GFP_KERNEL); + + if (!bchan->fifo_virt) { + dev_err(bdev->dev, "Failed to allocate desc fifo\n"); + return -ENOMEM; + } + } + + return BAM_DESC_FIFO_SIZE; +} + +/** + * bam_free_chan - Frees dma resources associated with specific channel + * @chan: specified channel + * + * Free the allocated fifo descriptor memory and channel resources + * + */ +static void bam_free_chan(struct dma_chan *chan) +{ + struct bam_chan *bchan = to_bam_chan(chan); + struct bam_device *bdev = bchan->bdev; + u32 val; + + vchan_free_chan_resources(to_virt_chan(chan)); + + if (bchan->curr_txd) { + dev_err(bchan->bdev->dev, "Cannot free busy channel\n"); + return; + } + + bam_reset_channel(bchan); + + dma_free_writecombine(bdev->dev, BAM_DESC_FIFO_SIZE, bchan->fifo_virt, + bchan->fifo_phys); + bchan->fifo_virt = NULL; + + /* mask irq for pipe/channel */ + val = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); + val &= ~BIT(bchan->id); + writel_relaxed(val, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); + + /* disable irq */ + writel_relaxed(0, bdev->regs + BAM_P_IRQ_EN(bchan->id)); +} + +/** + * bam_slave_config - set slave configuration for channel + * @chan: dma channel + * @cfg: slave configuration + * + * Sets slave configuration for channel + * + */ +static void bam_slave_config(struct bam_chan *bchan, + struct dma_slave_config *cfg) +{ + struct bam_device *bdev = bchan->bdev; + u32 maxburst; + + if (bchan->slave.direction == DMA_DEV_TO_MEM) + maxburst = bchan->slave.src_maxburst = cfg->src_maxburst; + else + maxburst = bchan->slave.dst_maxburst = cfg->dst_maxburst; + + /* set desc threshold */ + writel_relaxed(maxburst, bdev->regs + BAM_DESC_CNT_TRSHLD); +} + +/** + * bam_prep_slave_sg - Prep slave sg transaction + * + * @chan: dma channel + * @sgl: scatter gather list + * @sg_len: length of sg + * @direction: DMA transfer direction + * @flags: DMA flags + * @context: transfer context (unused) + */ +static struct dma_async_tx_descriptor *bam_prep_slave_sg(struct dma_chan *chan, + struct scatterlist *sgl, unsigned int sg_len, + enum dma_transfer_direction direction, unsigned long flags, + void *context) +{ + struct bam_chan *bchan = to_bam_chan(chan); + struct bam_device *bdev = bchan->bdev; + struct bam_async_desc *async_desc; + struct scatterlist *sg; + u32 i; + struct bam_desc_hw *desc; + + + if (!is_slave_direction(direction)) { + dev_err(bdev->dev, "invalid dma direction\n"); + return NULL; + } + + + /* allocate enough room to accomodate the number of entries */ + async_desc = kzalloc(sizeof(*async_desc) + + (sg_len * sizeof(struct bam_desc_hw)), GFP_NOWAIT); + + if (!async_desc) { + dev_err(bdev->dev, "failed to allocate async descriptor\n"); + goto err_out; + } + + async_desc->num_desc = sg_len; + async_desc->curr_desc = async_desc->desc; + async_desc->dir = direction; + + /* fill in descriptors, align hw descriptor to 8 bytes */ + desc = async_desc->desc; + for_each_sg(sgl, sg, sg_len, i) { + if (sg_dma_len(sg) > BAM_MAX_DATA_SIZE) { + dev_err(bdev->dev, "segment exceeds max size\n"); + goto err_out; + } + + desc->addr = sg_dma_address(sg); + desc->size = sg_dma_len(sg); + async_desc->length += sg_dma_len(sg); + desc++; + } + + return vchan_tx_prep(&bchan->vc, &async_desc->vd, flags); + +err_out: + kfree(async_desc); + return NULL; +} + +/** + * bam_dma_terminate_all - terminate all transactions on a channel + * @bchan: bam dma channel + * + * Dequeues and frees all transactions + * No callbacks are done + * + */ +static void bam_dma_terminate_all(struct bam_chan *bchan) +{ + unsigned long flag; + LIST_HEAD(head); + + /* remove all transactions, including active transaction */ + spin_lock_irqsave(&bchan->vc.lock, flag); + if (bchan->curr_txd) { + list_add(&bchan->curr_txd->vd.node, &bchan->vc.desc_issued); + bchan->curr_txd = NULL; + } + + vchan_get_all_descriptors(&bchan->vc, &head); + spin_unlock_irqrestore(&bchan->vc.lock, flag); + + vchan_dma_desc_free_list(&bchan->vc, &head); +} + +/** + * bam_control - DMA device control + * @chan: dma channel + * @cmd: control cmd + * @arg: cmd argument + * + * Perform DMA control command + * + */ +static int bam_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd, + unsigned long arg) +{ + struct bam_chan *bchan = to_bam_chan(chan); + struct bam_device *bdev = bchan->bdev; + int ret = 0; + unsigned long flag; + + switch (cmd) { + case DMA_PAUSE: + spin_lock_irqsave(&bchan->vc.lock, flag); + writel_relaxed(1, bdev->regs + BAM_P_HALT(bchan->id)); + bchan->paused = 1; + spin_unlock_irqrestore(&bchan->vc.lock, flag); + break; + case DMA_RESUME: + spin_lock_irqsave(&bchan->vc.lock, flag); + writel_relaxed(0, bdev->regs + BAM_P_HALT(bchan->id)); + bchan->paused = 0; + spin_unlock_irqrestore(&bchan->vc.lock, flag); + break; + case DMA_TERMINATE_ALL: + bam_dma_terminate_all(bchan); + break; + case DMA_SLAVE_CONFIG: + bam_slave_config(bchan, (struct dma_slave_config *)arg); + break; + default: + ret = -ENXIO; + break; + } + + return ret; +} + +/** + * process_channel_irqs - processes the channel interrupts + * @bdev: bam controller + * + * This function processes the channel interrupts + * + */ +static u32 process_channel_irqs(struct bam_device *bdev) +{ + u32 i, srcs, pipe_stts; + unsigned long flags; + struct bam_async_desc *async_desc; + + srcs = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_EE(bdev->ee)); + + /* return early if no pipe/channel interrupts are present */ + if (!(srcs & P_IRQ)) + return srcs; + + for (i = 0; i < bdev->num_channels; i++) { + struct bam_chan *bchan = &bdev->channels[i]; + if (srcs & BIT(i)) { + /* clear pipe irq */ + pipe_stts = readl_relaxed(bdev->regs + + BAM_P_IRQ_STTS(i)); + + writel_relaxed(pipe_stts, bdev->regs + + BAM_P_IRQ_CLR(i)); + + spin_lock_irqsave(&bchan->vc.lock, flags); + async_desc = bchan->curr_txd; + + if (async_desc) { + async_desc->num_desc -= async_desc->xfer_len; + async_desc->curr_desc += async_desc->xfer_len; + bchan->curr_txd = NULL; + + /* manage FIFO */ + bchan->head += async_desc->xfer_len; + bchan->head %= MAX_DESCRIPTORS; + + /* + * if complete, process cookie. Otherwise + * push back to front of desc_issued so that + * it gets restarted by the tasklet + */ + if (!async_desc->num_desc) + vchan_cookie_complete(&async_desc->vd); + else + list_add(&async_desc->vd.node, + &bchan->vc.desc_issued); + } + + spin_unlock_irqrestore(&bchan->vc.lock, flags); + } + } + + return srcs; +} + +/** + * bam_dma_irq - irq handler for bam controller + * @irq: IRQ of interrupt + * @data: callback data + * + * IRQ handler for the bam controller + */ +static irqreturn_t bam_dma_irq(int irq, void *data) +{ + struct bam_device *bdev = data; + u32 clr_mask = 0, srcs = 0; + + srcs |= process_channel_irqs(bdev); + + /* kick off tasklet to start next dma transfer */ + if (srcs & P_IRQ) + tasklet_schedule(&bdev->task); + + if (srcs & BAM_IRQ) + clr_mask = readl_relaxed(bdev->regs + BAM_IRQ_STTS); + + /* don't allow reorder of the various accesses to the BAM registers */ + mb(); + + writel_relaxed(clr_mask, bdev->regs + BAM_IRQ_CLR); + + return IRQ_HANDLED; +} + +/** + * bam_tx_status - returns status of transaction + * @chan: dma channel + * @cookie: transaction cookie + * @txstate: DMA transaction state + * + * Return status of dma transaction + */ +static enum dma_status bam_tx_status(struct dma_chan *chan, dma_cookie_t cookie, + struct dma_tx_state *txstate) +{ + struct bam_chan *bchan = to_bam_chan(chan); + struct virt_dma_desc *vd; + int ret; + size_t residue = 0; + unsigned int i; + unsigned long flags; + + ret = dma_cookie_status(chan, cookie, txstate); + if (ret == DMA_COMPLETE) + return ret; + + if (!txstate) + return bchan->paused ? DMA_PAUSED : ret; + + spin_lock_irqsave(&bchan->vc.lock, flags); + vd = vchan_find_desc(&bchan->vc, cookie); + if (vd) + residue = container_of(vd, struct bam_async_desc, vd)->length; + else if (bchan->curr_txd && bchan->curr_txd->vd.tx.cookie == cookie) + for (i = 0; i < bchan->curr_txd->num_desc; i++) + residue += bchan->curr_txd->curr_desc[i].size; + + spin_unlock_irqrestore(&bchan->vc.lock, flags); + + dma_set_residue(txstate, residue); + + if (ret == DMA_IN_PROGRESS && bchan->paused) + ret = DMA_PAUSED; + + return ret; +} + +/** + * bam_start_dma - start next transaction + * @bchan - bam dma channel + * + * Note: must hold bam dma channel vc.lock + */ +static void bam_start_dma(struct bam_chan *bchan) +{ + struct virt_dma_desc *vd = vchan_next_desc(&bchan->vc); + struct bam_device *bdev = bchan->bdev; + struct bam_async_desc *async_desc; + struct bam_desc_hw *desc; + struct bam_desc_hw *fifo = PTR_ALIGN(bchan->fifo_virt, + sizeof(struct bam_desc_hw)); + + if (!vd) + return; + + list_del(&vd->node); + + async_desc = container_of(vd, struct bam_async_desc, vd); + bchan->curr_txd = async_desc; + + /* on first use, initialize the channel hardware */ + if (!bchan->initialized) + bam_chan_init_hw(bchan, async_desc->dir); + + + desc = bchan->curr_txd->curr_desc; + + if (async_desc->num_desc > MAX_DESCRIPTORS) + async_desc->xfer_len = MAX_DESCRIPTORS; + else + async_desc->xfer_len = async_desc->num_desc; + + /* set INT on last descriptor */ + desc[async_desc->xfer_len - 1].flags |= DESC_FLAG_INT; + + if (bchan->tail + async_desc->xfer_len > MAX_DESCRIPTORS) { + u32 partial = MAX_DESCRIPTORS - bchan->tail; + + memcpy(&fifo[bchan->tail], desc, + partial * sizeof(struct bam_desc_hw)); + memcpy(fifo, &desc[partial], (async_desc->xfer_len - partial) * + sizeof(struct bam_desc_hw)); + } else { + memcpy(&fifo[bchan->tail], desc, + async_desc->xfer_len * sizeof(struct bam_desc_hw)); + } + + bchan->tail += async_desc->xfer_len; + bchan->tail %= MAX_DESCRIPTORS; + + /* ensure descriptor writes and dma start not reordered */ + wmb(); + writel_relaxed(bchan->tail * sizeof(struct bam_desc_hw), + bdev->regs + BAM_P_EVNT_REG(bchan->id)); +} + +/** + * dma_tasklet - DMA IRQ tasklet + * @data: tasklet argument (bam controller structure) + * + * Sets up next DMA operation and then processes all completed transactions + */ +static void dma_tasklet(unsigned long data) +{ + struct bam_device *bdev = (struct bam_device *)data; + struct bam_chan *bchan; + unsigned long flags; + unsigned int i; + + /* go through the channels and kick off transactions */ + for (i = 0; i < bdev->num_channels; i++) { + bchan = &bdev->channels[i]; + spin_lock_irqsave(&bchan->vc.lock, flags); + + if (!list_empty(&bchan->vc.desc_issued) && !bchan->curr_txd) + bam_start_dma(bchan); + spin_unlock_irqrestore(&bchan->vc.lock, flags); + } +} + +/** + * bam_issue_pending - starts pending transactions + * @chan: dma channel + * + * Calls tasklet directly which in turn starts any pending transactions + */ +static void bam_issue_pending(struct dma_chan *chan) +{ + struct bam_chan *bchan = to_bam_chan(chan); + unsigned long flags; + + spin_lock_irqsave(&bchan->vc.lock, flags); + + /* if work pending and idle, start a transaction */ + if (vchan_issue_pending(&bchan->vc) && !bchan->curr_txd) + bam_start_dma(bchan); + + spin_unlock_irqrestore(&bchan->vc.lock, flags); +} + +/** + * bam_dma_free_desc - free descriptor memory + * @vd: virtual descriptor + * + */ +static void bam_dma_free_desc(struct virt_dma_desc *vd) +{ + struct bam_async_desc *async_desc = container_of(vd, + struct bam_async_desc, vd); + + kfree(async_desc); +} + +static struct dma_chan *bam_dma_xlate(struct of_phandle_args *dma_spec, + struct of_dma *of) +{ + struct bam_device *bdev = container_of(of->of_dma_data, + struct bam_device, common); + unsigned int request; + + if (dma_spec->args_count != 1) + return NULL; + + request = dma_spec->args[0]; + if (request >= bdev->num_channels) + return NULL; + + return dma_get_slave_channel(&(bdev->channels[request].vc.chan)); +} + +/** + * bam_init + * @bdev: bam device + * + * Initialization helper for global bam registers + */ +static int bam_init(struct bam_device *bdev) +{ + u32 val; + + /* read revision and configuration information */ + val = readl_relaxed(bdev->regs + BAM_REVISION) & NUM_EES_MASK; + + /* check that configured EE is within range */ + if (bdev->ee >= val) + return -EINVAL; + + val = readl_relaxed(bdev->regs + BAM_NUM_PIPES); + bdev->num_channels = val & BAM_NUM_PIPES_MASK; + + /* s/w reset bam */ + /* after reset all pipes are disabled and idle */ + val = readl_relaxed(bdev->regs + BAM_CTRL); + val |= BAM_SW_RST; + writel_relaxed(val, bdev->regs + BAM_CTRL); + val &= ~BAM_SW_RST; + writel_relaxed(val, bdev->regs + BAM_CTRL); + + /* make sure previous stores are visible before enabling BAM */ + wmb(); + + /* enable bam */ + val |= BAM_EN; + writel_relaxed(val, bdev->regs + BAM_CTRL); + + /* set descriptor threshhold, start with 4 bytes */ + writel_relaxed(DEFAULT_CNT_THRSHLD, bdev->regs + BAM_DESC_CNT_TRSHLD); + + /* Enable default set of h/w workarounds, ie all except BAM_FULL_PIPE */ + writel_relaxed(BAM_CNFG_BITS_DEFAULT, bdev->regs + BAM_CNFG_BITS); + + /* enable irqs for errors */ + writel_relaxed(BAM_ERROR_EN | BAM_HRESP_ERR_EN, + bdev->regs + BAM_IRQ_EN); + + return 0; +} + +static void bam_channel_init(struct bam_device *bdev, struct bam_chan *bchan, + u32 index) +{ + bchan->id = index; + bchan->bdev = bdev; + + vchan_init(&bchan->vc, &bdev->common); + bchan->vc.desc_free = bam_dma_free_desc; +} + +static int bam_dma_probe(struct platform_device *pdev) +{ + struct bam_device *bdev; + struct resource *iores; + int ret, i; + + bdev = devm_kzalloc(&pdev->dev, sizeof(*bdev), GFP_KERNEL); + if (!bdev) + return -ENOMEM; + + bdev->dev = &pdev->dev; + + iores = platform_get_resource(pdev, IORESOURCE_MEM, 0); + bdev->regs = devm_ioremap_resource(&pdev->dev, iores); + if (IS_ERR(bdev->regs)) + return PTR_ERR(bdev->regs); + + bdev->irq = platform_get_irq(pdev, 0); + if (bdev->irq < 0) + return bdev->irq; + + bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk"); + if (IS_ERR(bdev->bamclk)) + return PTR_ERR(bdev->bamclk); + + ret = clk_prepare_enable(bdev->bamclk); + if (ret) { + dev_err(bdev->dev, "failed to prepare/enable clock"); + return ret; + } + + ret = of_property_read_u32(pdev->dev.of_node, "qcom,ee", &bdev->ee); + if (ret) { + dev_err(bdev->dev, "EE unspecified\n"); + return ret; + } + + ret = bam_init(bdev); + if (ret) + return ret; + + tasklet_init(&bdev->task, dma_tasklet, (unsigned long)bdev); + + bdev->channels = devm_kcalloc(bdev->dev, bdev->num_channels, + sizeof(*bdev->channels), GFP_KERNEL); + + if (!bdev->channels) { + ret = -ENOMEM; + goto err_disable_clk; + } + + /* allocate and initialize channels */ + INIT_LIST_HEAD(&bdev->common.channels); + + for (i = 0; i < bdev->num_channels; i++) + bam_channel_init(bdev, &bdev->channels[i], i); + + ret = devm_request_irq(bdev->dev, bdev->irq, bam_dma_irq, + IRQF_TRIGGER_HIGH, "bam_dma", bdev); + if (ret) + goto err_disable_clk; + + /* set max dma segment size */ + bdev->common.dev = bdev->dev; + bdev->common.dev->dma_parms = &bdev->dma_parms; + ret = dma_set_max_seg_size(bdev->common.dev, BAM_MAX_DATA_SIZE); + if (ret) { + dev_err(bdev->dev, "cannot set maximum segment size\n"); + goto err_disable_clk; + } + + platform_set_drvdata(pdev, bdev); + + /* set capabilities */ + dma_cap_zero(bdev->common.cap_mask); + dma_cap_set(DMA_SLAVE, bdev->common.cap_mask); + + /* initialize dmaengine apis */ + bdev->common.device_alloc_chan_resources = bam_alloc_chan; + bdev->common.device_free_chan_resources = bam_free_chan; + bdev->common.device_prep_slave_sg = bam_prep_slave_sg; + bdev->common.device_control = bam_control; + bdev->common.device_issue_pending = bam_issue_pending; + bdev->common.device_tx_status = bam_tx_status; + bdev->common.dev = bdev->dev; + + ret = dma_async_device_register(&bdev->common); + if (ret) { + dev_err(bdev->dev, "failed to register dma async device\n"); + goto err_disable_clk; + } + + ret = of_dma_controller_register(pdev->dev.of_node, bam_dma_xlate, + &bdev->common); + if (ret) + goto err_unregister_dma; + + return 0; + +err_unregister_dma: + dma_async_device_unregister(&bdev->common); +err_disable_clk: + clk_disable_unprepare(bdev->bamclk); + return ret; +} + +static int bam_dma_remove(struct platform_device *pdev) +{ + struct bam_device *bdev = platform_get_drvdata(pdev); + u32 i; + + of_dma_controller_free(pdev->dev.of_node); + dma_async_device_unregister(&bdev->common); + + /* mask all interrupts for this execution environment */ + writel_relaxed(0, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee)); + + devm_free_irq(bdev->dev, bdev->irq, bdev); + + for (i = 0; i < bdev->num_channels; i++) { + bam_dma_terminate_all(&bdev->channels[i]); + tasklet_kill(&bdev->channels[i].vc.task); + + dma_free_writecombine(bdev->dev, BAM_DESC_FIFO_SIZE, + bdev->channels[i].fifo_virt, + bdev->channels[i].fifo_phys); + } + + tasklet_kill(&bdev->task); + + clk_disable_unprepare(bdev->bamclk); + + return 0; +} + +static const struct of_device_id bam_of_match[] = { + { .compatible = "qcom,bam-v1.4.0", }, + { .compatible = "qcom,bam-v1.4.1", }, + {} +}; +MODULE_DEVICE_TABLE(of, bam_of_match); + +static struct platform_driver bam_dma_driver = { + .probe = bam_dma_probe, + .remove = bam_dma_remove, + .driver = { + .name = "bam-dma-engine", + .owner = THIS_MODULE, + .of_match_table = bam_of_match, + }, +}; + +module_platform_driver(bam_dma_driver); + +MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>"); +MODULE_DESCRIPTION("QCOM BAM DMA engine driver"); +MODULE_LICENSE("GPL v2");

[v5,1/2] dmaengine: add Qualcomm BAM dma driver

Commit Message

Comments

Patch