| Message ID | 1395397968-6242-6-git-send-email-phil.edworthy@renesas.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > This patch adds the bindings for the rcar PCIE driver. The driver > resides under drivers/pci/host/pcie-rcar.c > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> I have one question below. If you can answer this with yes after thinking again about it, this is: Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > --- > Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 ++++++++++++++++++++++ > 1 file changed, 40 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci.txt > > diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt > new file mode 100644 > index 0000000..0e219b0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > @@ -0,0 +1,40 @@ > +* Renesas RCar PCIe interface > + > +Required properties: > +- compatible: should contain one of the following > + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", "renesas,r8a7791-pcie" > +- reg: base addresses and lengths of the pcie controller. > +- #address-cells: set to <3> > +- #size-cells: set to <2> > +- device_type: set to "pci" > +- ranges: ranges for the PCI memory and I/O regions > +- interrupts: interrupt values for MSI interrupt > +- #interrupt-cells: set to <1> > +- interrupt-map-mask and interrupt-map: standard PCI properties > + to define the mapping of the PCIe interface to interrupt > + numbers. > +- clocks: from common clock binding: handle to pci clock. > +- clock-names: from common clock binding: should be "pcie" You really only have one PCIe clock? So the controller is generating the PCIe bus clock from it's register clock? No need to enable any other clock for PCIe to work? > + > +Example: > + > +SoC specific DT Entry: > + > + pcie: pcie@0x01000000 { > + compatible = "renesas,r8a7790-pcie"; > + reg = <0 0xfe000000 0 0x80000>; > + #address-cells = <3>; > + #size-cells = <2>; > + device_type = "pci"; > + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 > + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 > + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 > + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; > + interrupts = <0 116 4>; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0>; > + interrupt-map = <0 0 0 0 &gic 0 116 4>; > + clocks = <&mstp3_clks R8A7790_CLK_PCIE>; > + clock-names = "pcie"; > + status = "disabled"; > + };
Hi Lucas, On 21/03/2014 11:24, Lucas wrote: > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > This patch adds the bindings for the rcar PCIE driver. The driver > > resides under drivers/pci/host/pcie-rcar.c > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > I have one question below. If you can answer this with yes after > thinking again about it, this is: > > Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > > --- > > Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 ++++++++++++++++++++++ > > 1 file changed, 40 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/ > Documentation/devicetree/bindings/pci/rcar-pci.txt > > new file mode 100644 > > index 0000000..0e219b0 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > @@ -0,0 +1,40 @@ > > +* Renesas RCar PCIe interface > > + > > +Required properties: > > +- compatible: should contain one of the following > > + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", "renesas,r8a7791-pcie" > > +- reg: base addresses and lengths of the pcie controller. > > +- #address-cells: set to <3> > > +- #size-cells: set to <2> > > +- device_type: set to "pci" > > +- ranges: ranges for the PCI memory and I/O regions > > +- interrupts: interrupt values for MSI interrupt > > +- #interrupt-cells: set to <1> > > +- interrupt-map-mask and interrupt-map: standard PCI properties > > + to define the mapping of the PCIe interface to interrupt > > + numbers. > > +- clocks: from common clock binding: handle to pci clock. > > +- clock-names: from common clock binding: should be "pcie" > > You really only have one PCIe clock? So the controller is generating the > PCIe bus clock from it's register clock? No need to enable any other > clock for PCIe to work? Yes, just the one clock. The PCIe bus clock is an external clock dedicated to PCIe and SATA, and we have no control over it. > > + > > +Example: > > + > > +SoC specific DT Entry: > > + > > + pcie: pcie@0x01000000 { > > + compatible = "renesas,r8a7790-pcie"; > > + reg = <0 0xfe000000 0 0x80000>; > > + #address-cells = <3>; > > + #size-cells = <2>; > > + device_type = "pci"; > > + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 > > + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 > > + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 > > + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; > > + interrupts = <0 116 4>; > > + #interrupt-cells = <1>; > > + interrupt-map-mask = <0 0 0 0>; > > + interrupt-map = <0 0 0 0 &gic 0 116 4>; > > + clocks = <&mstp3_clks R8A7790_CLK_PCIE>; > > + clock-names = "pcie"; > > + status = "disabled"; > > + }; > > -- > Pengutronix e.K. | Lucas Stach | > Industrial Linux Solutions | http://www.pengutronix.de/ | > Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-5076 | > Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | > Thanks Phil -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Am Freitag, den 21.03.2014, 14:18 +0000 schrieb Phil.Edworthy@renesas.com: > Hi Lucas, > > On 21/03/2014 11:24, Lucas wrote: > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > bindings > > > > Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > > This patch adds the bindings for the rcar PCIE driver. The driver > > > resides under drivers/pci/host/pcie-rcar.c > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > I have one question below. If you can answer this with yes after > > thinking again about it, this is: > > > > Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > > > --- > > > Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > ++++++++++++++++++++++ > > > 1 file changed, 40 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > > > diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/ > > Documentation/devicetree/bindings/pci/rcar-pci.txt > > > new file mode 100644 > > > index 0000000..0e219b0 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > @@ -0,0 +1,40 @@ > > > +* Renesas RCar PCIe interface > > > + > > > +Required properties: > > > +- compatible: should contain one of the following > > > + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > "renesas,r8a7791-pcie" > > > +- reg: base addresses and lengths of the pcie controller. > > > +- #address-cells: set to <3> > > > +- #size-cells: set to <2> > > > +- device_type: set to "pci" > > > +- ranges: ranges for the PCI memory and I/O regions > > > +- interrupts: interrupt values for MSI interrupt > > > +- #interrupt-cells: set to <1> > > > +- interrupt-map-mask and interrupt-map: standard PCI properties > > > + to define the mapping of the PCIe interface to interrupt > > > + numbers. > > > +- clocks: from common clock binding: handle to pci clock. > > > +- clock-names: from common clock binding: should be "pcie" > > > > You really only have one PCIe clock? So the controller is generating the > > PCIe bus clock from it's register clock? No need to enable any other > > clock for PCIe to work? > Yes, just the one clock. The PCIe bus clock is an external clock dedicated > to PCIe and SATA, and we have no control over it. > Is this some kind of always-on clock? If not you probably want a reference to it from the PCIe driver even if it's shared between SATA and PCIe. After all you don't want to end up unconditionally enabling this clock from the board or SoC level just to have PCIe working, right? Regards, Lucas
Hi Lucas, On: 21/03/2014 14:31, Lucas wrote: > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > Am Freitag, den 21.03.2014, 14:18 +0000 schrieb > Phil.Edworthy@renesas.com: > > Hi Lucas, > > > > On 21/03/2014 11:24, Lucas wrote: > > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > bindings > > > > > > Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > > > This patch adds the bindings for the rcar PCIE driver. The driver > > > > resides under drivers/pci/host/pcie-rcar.c > > > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > > > I have one question below. If you can answer this with yes after > > > thinking again about it, this is: > > > > > > Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > > > > --- > > > > Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > > ++++++++++++++++++++++ > > > > 1 file changed, 40 insertions(+) > > > > create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > > > > > diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/ > > > Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > new file mode 100644 > > > > index 0000000..0e219b0 > > > > --- /dev/null > > > > +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > @@ -0,0 +1,40 @@ > > > > +* Renesas RCar PCIe interface > > > > + > > > > +Required properties: > > > > +- compatible: should contain one of the following > > > > + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > > "renesas,r8a7791-pcie" > > > > +- reg: base addresses and lengths of the pcie controller. > > > > +- #address-cells: set to <3> > > > > +- #size-cells: set to <2> > > > > +- device_type: set to "pci" > > > > +- ranges: ranges for the PCI memory and I/O regions > > > > +- interrupts: interrupt values for MSI interrupt > > > > +- #interrupt-cells: set to <1> > > > > +- interrupt-map-mask and interrupt-map: standard PCI properties > > > > + to define the mapping of the PCIe interface to interrupt > > > > + numbers. > > > > +- clocks: from common clock binding: handle to pci clock. > > > > +- clock-names: from common clock binding: should be "pcie" > > > > > > You really only have one PCIe clock? So the controller is generating the > > > PCIe bus clock from it's register clock? No need to enable any other > > > clock for PCIe to work? > > Yes, just the one clock. The PCIe bus clock is an external clock dedicated > > to PCIe and SATA, and we have no control over it. > > > Is this some kind of always-on clock? If not you probably want a > reference to it from the PCIe driver even if it's shared between SATA > and PCIe. After all you don't want to end up unconditionally enabling > this clock from the board or SoC level just to have PCIe working, right? Ok, I see, I'll need a reference to a board clock, even if it's always on for these boards. > Regards, > Lucas > -- > Pengutronix e.K. | Lucas Stach | > Industrial Linux Solutions | http://www.pengutronix.de/ | > Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-5076 | > Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | > Thanks Phil -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Lucas, On: 21/03/2014 15:02, Phil wrote: > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > Hi Lucas, > > On: 21/03/2014 14:31, Lucas wrote: > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > > > Am Freitag, den 21.03.2014, 14:18 +0000 schrieb > > Phil.Edworthy@renesas.com: > > > Hi Lucas, > > > > > > On 21/03/2014 11:24, Lucas wrote: > > > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > > bindings > > > > > > > > Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > > > > This patch adds the bindings for the rcar PCIE driver. The driver > > > > > resides under drivers/pci/host/pcie-rcar.c > > > > > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > > > > > I have one question below. If you can answer this with yes after > > > > thinking again about it, this is: > > > > > > > > Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > > > > > --- > > > > > Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > > > ++++++++++++++++++++++ > > > > > 1 file changed, 40 insertions(+) > > > > > create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > > > > > > > diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/ > > > > Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > > new file mode 100644 > > > > > index 0000000..0e219b0 > > > > > --- /dev/null > > > > > +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > > @@ -0,0 +1,40 @@ > > > > > +* Renesas RCar PCIe interface > > > > > + > > > > > +Required properties: > > > > > +- compatible: should contain one of the following > > > > > + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > > > "renesas,r8a7791-pcie" > > > > > +- reg: base addresses and lengths of the pcie controller. > > > > > +- #address-cells: set to <3> > > > > > +- #size-cells: set to <2> > > > > > +- device_type: set to "pci" > > > > > +- ranges: ranges for the PCI memory and I/O regions > > > > > +- interrupts: interrupt values for MSI interrupt > > > > > +- #interrupt-cells: set to <1> > > > > > +- interrupt-map-mask and interrupt-map: standard PCI properties > > > > > + to define the mapping of the PCIe interface to interrupt > > > > > + numbers. > > > > > +- clocks: from common clock binding: handle to pci clock. > > > > > +- clock-names: from common clock binding: should be "pcie" > > > > > > > > You really only have one PCIe clock? So the controller is generating the > > > > PCIe bus clock from it's register clock? No need to enable any other > > > > clock for PCIe to work? > > > Yes, just the one clock. The PCIe bus clock is an external clock dedicated > > > to PCIe and SATA, and we have no control over it. > > > > > Is this some kind of always-on clock? If not you probably want a > > reference to it from the PCIe driver even if it's shared between SATA > > and PCIe. After all you don't want to end up unconditionally enabling > > this clock from the board or SoC level just to have PCIe working, right? > Ok, I see, I'll need a reference to a board clock, even if it's always on for > these boards. One small question... The patches added the PCIe host controller to two devices, r8a7790 and r8a7791. The r8a7790-based Lager board doesn't have the necessary hardware to use PCIe, so should I add a dummy pcie_bus clock to the Lager board dts, even though PCIe is not used? I'm just wondering what the dts file looks like for a board that doesn't support many interfaces. Does it become littered with dummy clocks and regulators? Thanks Phil -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 24/03/14 12:04, Phil.Edworthy@renesas.com wrote: > Hi Lucas, > > On: 21/03/2014 15:02, Phil wrote: >> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > bindings >> >> Hi Lucas, >> >> On: 21/03/2014 14:31, Lucas wrote: >>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > bindings >>> >>> Am Freitag, den 21.03.2014, 14:18 +0000 schrieb >>> Phil.Edworthy@renesas.com: >>>> Hi Lucas, >>>> >>>> On 21/03/2014 11:24, Lucas wrote: >>>>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device > tree >>>> bindings >>>>> >>>>> Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: >>>>>> This patch adds the bindings for the rcar PCIE driver. The > driver >>>>>> resides under drivers/pci/host/pcie-rcar.c >>>>>> >>>>>> Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> >>>>> >>>>> I have one question below. If you can answer this with yes after >>>>> thinking again about it, this is: >>>>> >>>>> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> >>>>>> --- >>>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 >>>> ++++++++++++++++++++++ >>>>>> 1 file changed, 40 insertions(+) >>>>>> create mode 100644 > Documentation/devicetree/bindings/pci/rcar-pci.txt >>>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt > b/ >>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt >>>>>> new file mode 100644 >>>>>> index 0000000..0e219b0 >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt >>>>>> @@ -0,0 +1,40 @@ >>>>>> +* Renesas RCar PCIe interface >>>>>> + >>>>>> +Required properties: >>>>>> +- compatible: should contain one of the following >>>>>> + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", >>>> "renesas,r8a7791-pcie" >>>>>> +- reg: base addresses and lengths of the pcie controller. >>>>>> +- #address-cells: set to <3> >>>>>> +- #size-cells: set to <2> >>>>>> +- device_type: set to "pci" >>>>>> +- ranges: ranges for the PCI memory and I/O regions >>>>>> +- interrupts: interrupt values for MSI interrupt >>>>>> +- #interrupt-cells: set to <1> >>>>>> +- interrupt-map-mask and interrupt-map: standard PCI properties >>>>>> + to define the mapping of the PCIe interface to interrupt >>>>>> + numbers. >>>>>> +- clocks: from common clock binding: handle to pci clock. >>>>>> +- clock-names: from common clock binding: should be "pcie" >>>>> >>>>> You really only have one PCIe clock? So the controller is > generating the >>>>> PCIe bus clock from it's register clock? No need to enable any > other >>>>> clock for PCIe to work? >>>> Yes, just the one clock. The PCIe bus clock is an external clock > dedicated >>>> to PCIe and SATA, and we have no control over it. >>>> >>> Is this some kind of always-on clock? If not you probably want a >>> reference to it from the PCIe driver even if it's shared between SATA >>> and PCIe. After all you don't want to end up unconditionally enabling >>> this clock from the board or SoC level just to have PCIe working, > right? >> Ok, I see, I'll need a reference to a board clock, even if it's always > on for >> these boards. > One small question... > > The patches added the PCIe host controller to two devices, r8a7790 and > r8a7791. The r8a7790-based Lager board doesn't have the necessary hardware > to use PCIe, so should I add a dummy pcie_bus clock to the Lager board > dts, even though PCIe is not used? > > I'm just wondering what the dts file looks like for a board that doesn't > support many interfaces. Does it become littered with dummy clocks and > regulators? The bridge node should be set to disabled by default so it never gets probed. Any boards that want to use it can over-ride the status to be enabled.
Hi Ben, On: 24/03/2014 12:16, Ben wrote: > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > On 24/03/14 12:04, Phil.Edworthy@renesas.com wrote: > > Hi Lucas, > > > > On: 21/03/2014 15:02, Phil wrote: > >> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > bindings > >> > >> Hi Lucas, > >> > >> On: 21/03/2014 14:31, Lucas wrote: > >>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > bindings > >>> > >>> Am Freitag, den 21.03.2014, 14:18 +0000 schrieb > >>> Phil.Edworthy@renesas.com: > >>>> Hi Lucas, > >>>> > >>>> On 21/03/2014 11:24, Lucas wrote: > >>>>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device > > tree > >>>> bindings > >>>>> > >>>>> Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > >>>>>> This patch adds the bindings for the rcar PCIE driver. The > > driver > >>>>>> resides under drivers/pci/host/pcie-rcar.c > >>>>>> > >>>>>> Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > >>>>> > >>>>> I have one question below. If you can answer this with yes after > >>>>> thinking again about it, this is: > >>>>> > >>>>> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > >>>>>> --- > >>>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > >>>> ++++++++++++++++++++++ > >>>>>> 1 file changed, 40 insertions(+) > >>>>>> create mode 100644 > > Documentation/devicetree/bindings/pci/rcar-pci.txt > >>>>>> > >>>>>> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt > > b/ > >>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt > >>>>>> new file mode 100644 > >>>>>> index 0000000..0e219b0 > >>>>>> --- /dev/null > >>>>>> +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > >>>>>> @@ -0,0 +1,40 @@ > >>>>>> +* Renesas RCar PCIe interface > >>>>>> + > >>>>>> +Required properties: > >>>>>> +- compatible: should contain one of the following > >>>>>> + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > >>>> "renesas,r8a7791-pcie" > >>>>>> +- reg: base addresses and lengths of the pcie controller. > >>>>>> +- #address-cells: set to <3> > >>>>>> +- #size-cells: set to <2> > >>>>>> +- device_type: set to "pci" > >>>>>> +- ranges: ranges for the PCI memory and I/O regions > >>>>>> +- interrupts: interrupt values for MSI interrupt > >>>>>> +- #interrupt-cells: set to <1> > >>>>>> +- interrupt-map-mask and interrupt-map: standard PCI properties > >>>>>> + to define the mapping of the PCIe interface to interrupt > >>>>>> + numbers. > >>>>>> +- clocks: from common clock binding: handle to pci clock. > >>>>>> +- clock-names: from common clock binding: should be "pcie" > >>>>> > >>>>> You really only have one PCIe clock? So the controller is > > generating the > >>>>> PCIe bus clock from it's register clock? No need to enable any > > other > >>>>> clock for PCIe to work? > >>>> Yes, just the one clock. The PCIe bus clock is an external clock > > dedicated > >>>> to PCIe and SATA, and we have no control over it. > >>>> > >>> Is this some kind of always-on clock? If not you probably want a > >>> reference to it from the PCIe driver even if it's shared between SATA > >>> and PCIe. After all you don't want to end up unconditionally enabling > >>> this clock from the board or SoC level just to have PCIe working, > > right? > >> Ok, I see, I'll need a reference to a board clock, even if it's always > > on for > >> these boards. > > One small question... > > > > The patches added the PCIe host controller to two devices, r8a7790 and > > r8a7791. The r8a7790-based Lager board doesn't have the necessary hardware > > to use PCIe, so should I add a dummy pcie_bus clock to the Lager board > > dts, even though PCIe is not used? > > > > I'm just wondering what the dts file looks like for a board that doesn't > > support many interfaces. Does it become littered with dummy clocks and > > regulators? > > The bridge node should be set to disabled by default so it never gets > probed. Any boards that want to use it can over-ride the status to be > enabled. Ok, thanks. Phil -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Ben, On: 24/03/2014 12:25, Phil wrote: > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > Hi Ben, > > On: 24/03/2014 12:16, Ben wrote: > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > > > On 24/03/14 12:04, Phil.Edworthy@renesas.com wrote: > > > Hi Lucas, > > > > > > On: 21/03/2014 15:02, Phil wrote: > > >> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > > bindings > > >> > > >> Hi Lucas, > > >> > > >> On: 21/03/2014 14:31, Lucas wrote: > > >>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > > bindings > > >>> > > >>> Am Freitag, den 21.03.2014, 14:18 +0000 schrieb > > >>> Phil.Edworthy@renesas.com: > > >>>> Hi Lucas, > > >>>> > > >>>> On 21/03/2014 11:24, Lucas wrote: > > >>>>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device > > > tree > > >>>> bindings > > >>>>> > > >>>>> Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > >>>>>> This patch adds the bindings for the rcar PCIE driver. The > > > driver > > >>>>>> resides under drivers/pci/host/pcie-rcar.c > > >>>>>> > > >>>>>> Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > >>>>> > > >>>>> I have one question below. If you can answer this with yes after > > >>>>> thinking again about it, this is: > > >>>>> > > >>>>> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > > >>>>>> --- > > >>>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > > >>>> ++++++++++++++++++++++ > > >>>>>> 1 file changed, 40 insertions(+) > > >>>>>> create mode 100644 > > > Documentation/devicetree/bindings/pci/rcar-pci.txt > > >>>>>> > > >>>>>> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > b/ > > >>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt > > >>>>>> new file mode 100644 > > >>>>>> index 0000000..0e219b0 > > >>>>>> --- /dev/null > > >>>>>> +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > >>>>>> @@ -0,0 +1,40 @@ > > >>>>>> +* Renesas RCar PCIe interface > > >>>>>> + > > >>>>>> +Required properties: > > >>>>>> +- compatible: should contain one of the following > > >>>>>> + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > > >>>> "renesas,r8a7791-pcie" > > >>>>>> +- reg: base addresses and lengths of the pcie controller. > > >>>>>> +- #address-cells: set to <3> > > >>>>>> +- #size-cells: set to <2> > > >>>>>> +- device_type: set to "pci" > > >>>>>> +- ranges: ranges for the PCI memory and I/O regions > > >>>>>> +- interrupts: interrupt values for MSI interrupt > > >>>>>> +- #interrupt-cells: set to <1> > > >>>>>> +- interrupt-map-mask and interrupt-map: standard PCI properties > > >>>>>> + to define the mapping of the PCIe interface to interrupt > > >>>>>> + numbers. > > >>>>>> +- clocks: from common clock binding: handle to pci clock. > > >>>>>> +- clock-names: from common clock binding: should be "pcie" > > >>>>> > > >>>>> You really only have one PCIe clock? So the controller is > > > generating the > > >>>>> PCIe bus clock from it's register clock? No need to enable any > > > other > > >>>>> clock for PCIe to work? > > >>>> Yes, just the one clock. The PCIe bus clock is an external clock > > > dedicated > > >>>> to PCIe and SATA, and we have no control over it. > > >>>> > > >>> Is this some kind of always-on clock? If not you probably want a > > >>> reference to it from the PCIe driver even if it's shared between SATA > > >>> and PCIe. After all you don't want to end up unconditionally enabling > > >>> this clock from the board or SoC level just to have PCIe working, > > > right? > > >> Ok, I see, I'll need a reference to a board clock, even if it's always > > > on for > > >> these boards. > > > One small question... > > > > > > The patches added the PCIe host controller to two devices, r8a7790 and > > > r8a7791. The r8a7790-based Lager board doesn't have the necessary hardware > > > to use PCIe, so should I add a dummy pcie_bus clock to the Lager board > > > dts, even though PCIe is not used? > > > > > > I'm just wondering what the dts file looks like for a board that doesn't > > > support many interfaces. Does it become littered with dummy clocks and > > > regulators? > > > > The bridge node should be set to disabled by default so it never gets > > probed. Any boards that want to use it can over-ride the status to be > > enabled. > Ok, thanks. Hmm, yes it doesn't get probed, but you still get a build problem as the DT entry references an clock that doesn't exist. Maybe I'm missing something... Phil -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Am Montag, den 24.03.2014, 12:46 +0000 schrieb Phil.Edworthy@renesas.com: > Hi Ben, > > On: 24/03/2014 12:25, Phil wrote: > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > bindings > > > > Hi Ben, > > > > On: 24/03/2014 12:16, Ben wrote: > > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > bindings > > > > > > On 24/03/14 12:04, Phil.Edworthy@renesas.com wrote: > > > > Hi Lucas, > > > > > > > > On: 21/03/2014 15:02, Phil wrote: > > > >> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > > > bindings > > > >> > > > >> Hi Lucas, > > > >> > > > >> On: 21/03/2014 14:31, Lucas wrote: > > > >>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device > tree > > > > bindings > > > >>> > > > >>> Am Freitag, den 21.03.2014, 14:18 +0000 schrieb > > > >>> Phil.Edworthy@renesas.com: > > > >>>> Hi Lucas, > > > >>>> > > > >>>> On 21/03/2014 11:24, Lucas wrote: > > > >>>>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device > > > > tree > > > >>>> bindings > > > >>>>> > > > >>>>> Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > > >>>>>> This patch adds the bindings for the rcar PCIE driver. The > > > > driver > > > >>>>>> resides under drivers/pci/host/pcie-rcar.c > > > >>>>>> > > > >>>>>> Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > >>>>> > > > >>>>> I have one question below. If you can answer this with yes after > > > >>>>> thinking again about it, this is: > > > >>>>> > > > >>>>> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > > > >>>>>> --- > > > >>>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > > > >>>> ++++++++++++++++++++++ > > > >>>>>> 1 file changed, 40 insertions(+) > > > >>>>>> create mode 100644 > > > > Documentation/devicetree/bindings/pci/rcar-pci.txt > > > >>>>>> > > > >>>>>> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > > b/ > > > >>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt > > > >>>>>> new file mode 100644 > > > >>>>>> index 0000000..0e219b0 > > > >>>>>> --- /dev/null > > > >>>>>> +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > >>>>>> @@ -0,0 +1,40 @@ > > > >>>>>> +* Renesas RCar PCIe interface > > > >>>>>> + > > > >>>>>> +Required properties: > > > >>>>>> +- compatible: should contain one of the following > > > >>>>>> + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > > > >>>> "renesas,r8a7791-pcie" > > > >>>>>> +- reg: base addresses and lengths of the pcie controller. > > > >>>>>> +- #address-cells: set to <3> > > > >>>>>> +- #size-cells: set to <2> > > > >>>>>> +- device_type: set to "pci" > > > >>>>>> +- ranges: ranges for the PCI memory and I/O regions > > > >>>>>> +- interrupts: interrupt values for MSI interrupt > > > >>>>>> +- #interrupt-cells: set to <1> > > > >>>>>> +- interrupt-map-mask and interrupt-map: standard PCI > properties > > > >>>>>> + to define the mapping of the PCIe interface to interrupt > > > >>>>>> + numbers. > > > >>>>>> +- clocks: from common clock binding: handle to pci clock. > > > >>>>>> +- clock-names: from common clock binding: should be "pcie" > > > >>>>> > > > >>>>> You really only have one PCIe clock? So the controller is > > > > generating the > > > >>>>> PCIe bus clock from it's register clock? No need to enable any > > > > other > > > >>>>> clock for PCIe to work? > > > >>>> Yes, just the one clock. The PCIe bus clock is an external clock > > > > dedicated > > > >>>> to PCIe and SATA, and we have no control over it. > > > >>>> > > > >>> Is this some kind of always-on clock? If not you probably want a > > > >>> reference to it from the PCIe driver even if it's shared between > SATA > > > >>> and PCIe. After all you don't want to end up unconditionally > enabling > > > >>> this clock from the board or SoC level just to have PCIe working, > > > > right? > > > >> Ok, I see, I'll need a reference to a board clock, even if it's > always > > > > on for > > > >> these boards. > > > > One small question... > > > > > > > > The patches added the PCIe host controller to two devices, r8a7790 > and > > > > r8a7791. The r8a7790-based Lager board doesn't have the necessary > hardware > > > > to use PCIe, so should I add a dummy pcie_bus clock to the Lager > board > > > > dts, even though PCIe is not used? > > > > > > > > I'm just wondering what the dts file looks like for a board that > doesn't > > > > support many interfaces. Does it become littered with dummy clocks > and > > > > regulators? > > > > > > The bridge node should be set to disabled by default so it never gets > > > probed. Any boards that want to use it can over-ride the status to be > > > enabled. > > Ok, thanks. > Hmm, yes it doesn't get probed, but you still get a build problem as the > DT entry references an clock that doesn't exist. Maybe I'm missing > something... > If the clock is a board supplied one then you have to supply to clocks property from the board dts, to get rid of the compile failure. You can not have phandles in the PCIe node referencing a non-existing clock. Regards, Lucas
diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 0000000..0e219b0 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,40 @@ +* Renesas RCar PCIe interface + +Required properties: +- compatible: should contain one of the following + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", "renesas,r8a7791-pcie" +- reg: base addresses and lengths of the pcie controller. +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions +- interrupts: interrupt values for MSI interrupt +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: handle to pci clock. +- clock-names: from common clock binding: should be "pcie" + +Example: + +SoC specific DT Entry: + + pcie: pcie@0x01000000 { + compatible = "renesas,r8a7790-pcie"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + interrupts = <0 116 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7790_CLK_PCIE>; + clock-names = "pcie"; + status = "disabled"; + };
This patch adds the bindings for the rcar PCIE driver. The driver resides under drivers/pci/host/pcie-rcar.c Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> --- Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 ++++++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci.txt