diff mbox

[v2,1/2] ARM: dts: am335x-bone: add support for beaglebone NAND cape

Message ID 1395300886-383-2-git-send-email-pekon@ti.com (mailing list archive)
State New, archived
Headers show

Commit Message

pekon gupta March 20, 2014, 7:34 a.m. UTC 
Beaglebone Board can be connected to expansion boards to add devices to them.
These expansion boards are called 'capes'. This patch adds support for
following versions of Beaglebone(AM335x) NAND capes
(a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64
(b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224
Further information and datasheets can be found at [1] and [2]

* How to boot from NAND using Memory Expander + NAND Cape ? *
 - Important: As BOOTSEL values are sampled only at POR, so after changing any
   setting on SW2 (DIP switch), disconnect and reconnect all board power supply
   (including mini-USB console port) to POR the beaglebone.

 - Selection of ECC scheme
  for NAND cape(a), ROM code expects BCH8_HW ecc-scheme
  for NAND cape(b), ROM code expects BCH16_HW ecc-scheme

 - Selection of boot modes can be controlled via  DIP switch(SW2) present on
   Memory Expander cape, so first boot via MMC or other sources to flash NAND
   device and then switch to SW2[SWITCH_BOOT]=ON to boot from NAND Cape.
   SW2[SWITCH_BOOT] == OFF  follow default boot order  MMC-> SPI -> UART -> USB
   SW2[SWITCH_BOOT] == ON   boot mode selected via DIP switch(SW2)

 - For NAND boot following switch settings need to be followed
   SW2[ 0] = ON   (SYSBOOT[ 0]==0: NAND boot mode selected )
   SW2[ 1] = ON   (SYSBOOT[ 1]==0:       -- do --          )
   SW2[ 2] = OFF  (SYSBOOT[ 2]==1:       -- do --          )
   SW2[ 3] = OFF  (SYSBOOT[ 3]==1:       -- do --          )
   SW2[ 4] = ON   (SYSBOOT[ 4]==0:       -- do --          )
   SW2[ 8] = OFF  (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device )
   SW2[ 9] = ON   (SYSBOOT[ 9]==0: ECC done by ROM  )
   SW2[10] = ON   (SYSBOOT[10]==0: Non Muxed device )
   SW2[11] = ON   (SYSBOOT[11]==0:    -- do --      )

[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion
[2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module

Signed-off-by: Pekon Gupta <pekon@ti.com>
---
 arch/arm/boot/dts/am335x-bone-memory-cape.dts | 130 ++++++++++++++++++++++++++
 arch/arm/boot/dts/am335x-bone.dts             |   1 +
 arch/arm/boot/dts/am335x-boneblack.dts        |   1 +
 3 files changed, 132 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-bone-memory-cape.dts

Comments

Ezequiel Garcia May 12, 2014, 4:03 p.m. UTC | #1 
Pekon,

A few questions regarding this patch, despite the fact I'm not sure it will
ever be included.

On 20 Mar 01:04 PM, Pekon Gupta wrote:
> +			0x70 (MUX_MODE0 | PIN_INPUT_PULLUP )	/* gpmc_wait0.gpmc_wait0 */
> +			0x74 (MUX_MODE7 | PIN_OUTPUT_PULLUP)	/* gpmc_wpn.gpio0_30 */

Is this output pin?

> +			0x7c (MUX_MODE0 | PIN_OUTPUT_PULLUP)	/* gpmc_csn0.gpmc_csn0  */

Again: is this output pin?

> +		gpmc,wait-on-read = "true";
> +		gpmc,wait-on-write = "true";

The devicetree binding says these wait properties are bool, so the above
should be:

		gpmc,wait-on-read;
		gpmc,wait-on-write;

But the problem is that there's no wait-pin defined, so this not enabled.

Could you explain what should be the correct binding? This is very confusing
for me.

Thanks!
pekon gupta May 16, 2014, 7:39 p.m. UTC | #2 
Hi Ezequiel,

Sorry for delayed replies..

>From: Ezequiel Garcia [mailto:ezequiel.garcia@free-electrons.com]
>Pekon,
>
>A few questions regarding this patch, despite the fact I'm not sure it will
>ever be included.
>
>On 20 Mar 01:04 PM, Pekon Gupta wrote:	
>> +			0x70 (MUX_MODE0 | PIN_INPUT_PULLUP )	/* gpmc_wait0.gpmc_wait0 */
>> +			0x74 (MUX_MODE7 | PIN_OUTPUT_PULLUP)	/* gpmc_wpn.gpio0_30 */
>
>Is this output pin?
Yes, it's the "Write Protect (WP)" pin. And goes controller -> device.


>
>> +			0x7c (MUX_MODE0 | PIN_OUTPUT_PULLUP)	/* gpmc_csn0.gpmc_csn0  */
>
>Again: is this output pin?
>
Yes, this is "Chip-select"  and goes from controller -> device.
Though it should already have external pull-up resistor on board, to avoid
glitches due to noise, and avoid device getting confused when SoC
is not driving anything (like before pin-muxing).


>> +		gpmc,wait-on-read = "true";
>> +		gpmc,wait-on-write = "true";
>
>The devicetree binding says these wait properties are bool, so the above
>should be:
>
>		gpmc,wait-on-read;
>		gpmc,wait-on-write;
>
>But the problem is that there's no wait-pin defined, so this not enabled.
>
>Could you explain what should be the correct binding? This is very confusing
>for me.
>
I have fixed the above DT mapping in newer version of the patch [1].

Sorry, yes the wait-pin monitoring implementation is not cleanly done,
there is mix of platform_data and DT stuff. So in addition to updated DT patch
you need following patch to enable wait-pin monitoring in NAND driver.

http://www.spinics.net/lists/linux-omap/msg107253.html



with regards, pekon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/arch/arm/boot/dts/am335x-bone-memory-cape.dts b/arch/arm/boot/dts/am335x-bone-memory-cape.dts
new file mode 100644
index 0000000..9c9f6a6
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bone-memory-cape.dts
@@ -0,0 +1,130 @@ 
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This DTS adds supports for capes using GPMC interface to connect external
+ * memory like NAND, NOR Flash to Beaglebone-LT (white) and Beaglebone-Black.
+ */
+
+
+&am33xx_pinmux {
+	nand_flash_x16: nand_flash_x16 {
+		pinctrl-single,pins = <
+			0x00 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad0.gpmc_ad0 */
+			0x04 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad1.gpmc_ad1 */
+			0x08 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad2.gpmc_ad2 */
+			0x0c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad7.gpmc_ad7 */
+			0x20 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad8.gpmc_ad8 */
+			0x24 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad9.gpmc_ad9 */
+			0x28 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad10.gpmc_ad10 */
+			0x2c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad11.gpmc_ad11 */
+			0x30 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad12.gpmc_ad12 */
+			0x34 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad13.gpmc_ad13 */
+			0x38 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad14.gpmc_ad14 */
+			0x3c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad15.gpmc_ad15 */
+			0x70 (MUX_MODE0 | PIN_INPUT_PULLUP )	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (MUX_MODE7 | PIN_OUTPUT_PULLUP)	/* gpmc_wpn.gpio0_30 */
+			0x7c (MUX_MODE0 | PIN_OUTPUT_PULLUP)	/* gpmc_csn0.gpmc_csn0  */
+			0x90 (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_wen.gpmc_wen */
+			0x9c (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+};
+
+&elm {
+     status = "disabled";
+};
+
+&gpmc {
+     status = "disabled";
+};
+
+&gpmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x16>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <16>;
+		gpmc,device-width = <2>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <80>;
+		gpmc,cs-wr-off-ns = <80>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <80>;
+		gpmc,adv-wr-off-ns = <80>;
+		gpmc,we-on-ns = <20>;
+		gpmc,we-off-ns = <60>;
+		gpmc,oe-on-ns = <20>;
+		gpmc,oe-off-ns = <60>;
+		gpmc,access-ns = <40>;
+		gpmc,rd-cycle-ns = <80>;
+		gpmc,wr-cycle-ns = <80>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000C0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002C0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00A00000 0x1F600000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index 94ee427..f16bfcf 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -9,6 +9,7 @@ 
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+#include "am335x-bone-memory-cape.dts"
 
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index 6b71ad9..c030b24 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -9,6 +9,7 @@ 
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+#include "am335x-bone-memory-cape.dts"
 
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;