@@ -155,6 +155,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx25-pdk.dtb \
imx27-apf27.dtb \
imx27-apf27dev.dtb \
+ imx27-eukrea-mbimxsd27-baseboard.dtb \
imx27-pdk.dtb \
imx27-phytec-phycore-rdk.dtb \
imx27-phytec-phycard-s-rdk.dtb \
new file mode 100644
@@ -0,0 +1,296 @@
+/*
+ * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx27.dtsi"
+
+/ {
+ model = "Eukrea CPUIMX27";
+ compatible = "eukrea,cpuimx27", "fsl,imx27";
+
+ memory {
+ reg = <0xa0000000 0x04000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "simple-bus";
+
+ clk14745600: clock@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <14745600>;
+ reg = <0>;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&nfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nfc>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ status = "okay";
+};
+
+&owire {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_owire>;
+ status = "okay";
+};
+
+&sdhci2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhc2>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&usbh2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh2>;
+ dr_mode = "host";
+ phy_type = "ulpi";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "otg";
+ phy_type = "ulpi";
+ disable-over-current;
+ status = "okay";
+};
+
+&weim {
+ status = "okay";
+
+ nor: nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0 0x00000000 0x04000000>;
+ bank-width = <2>;
+ linux,mtd-name = "physmap-flash.0";
+ fsl,weim-cs-timing = <0x00008f03 0xa0330d01 0x002208c0>;
+ };
+
+ uart8250@3,200000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart8250_1>;
+ compatible = "ns8250";
+ clocks = <&clk14745600>;
+ fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
+ interrupts = <&gpio2 23 IRQ_TYPE_LEVEL_LOW>;
+ reg = <3 0x200000 0x1000>;
+ reg-shift = <1>;
+ reg-io-width = <1>;
+ no-loopback-test;
+ };
+
+ uart8250@3,400000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart8250_2>;
+ compatible = "ns8250";
+ clocks = <&clk14745600>;
+ fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
+ interrupts = <&gpio2 22 IRQ_TYPE_LEVEL_LOW>;
+ reg = <3 0x400000 0x1000>;
+ reg-shift = <1>;
+ reg-io-width = <1>;
+ no-loopback-test;
+ };
+
+ uart8250@3,800000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart8250_3>;
+ compatible = "ns8250";
+ clocks = <&clk14745600>;
+ fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
+ interrupts = <&gpio2 27 IRQ_TYPE_LEVEL_LOW>;
+ reg = <3 0x800000 0x1000>;
+ reg-shift = <1>;
+ reg-io-width = <1>;
+ no-loopback-test;
+ };
+
+ uart8250@3,1000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart8250_4>;
+ compatible = "ns8250";
+ clocks = <&clk14745600>;
+ fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
+ interrupts = <&gpio2 30 IRQ_TYPE_LEVEL_LOW>;
+ reg = <3 0x1000000 0x1000>;
+ reg-shift = <1>;
+ reg-io-width = <1>;
+ no-loopback-test;
+ };
+};
+
+&iomuxc {
+ imx27-eukrea-cpuimx27 {
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX27_PAD_SD3_CMD__FEC_TXD0 0x0
+ MX27_PAD_SD3_CLK__FEC_TXD1 0x0
+ MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
+ MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
+ MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
+ MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
+ MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
+ MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
+ MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
+ MX27_PAD_ATA_DATA7__FEC_MDC 0x0
+ MX27_PAD_ATA_DATA8__FEC_CRS 0x0
+ MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
+ MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
+ MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
+ MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
+ MX27_PAD_ATA_DATA13__FEC_COL 0x0
+ MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
+ MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX27_PAD_I2C_DATA__I2C_DATA 0x0
+ MX27_PAD_I2C_CLK__I2C_CLK 0x0
+ >;
+ };
+
+ pinctrl_nfc: nfcgrp {
+ fsl,pins = <
+ MX27_PAD_NFRB__NFRB 0x0
+ MX27_PAD_NFCLE__NFCLE 0x0
+ MX27_PAD_NFWP_B__NFWP_B 0x0
+ MX27_PAD_NFCE_B__NFCE_B 0x0
+ MX27_PAD_NFALE__NFALE 0x0
+ MX27_PAD_NFRE_B__NFRE_B 0x0
+ MX27_PAD_NFWE_B__NFWE_B 0x0
+ >;
+ };
+
+ pinctrl_owire: owiregrp {
+ fsl,pins = <
+ MX27_PAD_RTCK__OWIRE 0x0
+ >;
+ };
+
+ pinctrl_sdhc2: sdhc2grp {
+ fsl,pins = <
+ MX27_PAD_SD2_CLK__SD2_CLK 0x0
+ MX27_PAD_SD2_CMD__SD2_CMD 0x0
+ MX27_PAD_SD2_D0__SD2_D0 0x0
+ MX27_PAD_SD2_D1__SD2_D1 0x0
+ MX27_PAD_SD2_D2__SD2_D2 0x0
+ MX27_PAD_SD2_D3__SD2_D3 0x0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX27_PAD_USBH1_TXDM__UART4_TXD 0x0
+ MX27_PAD_USBH1_RXDP__UART4_RXD 0x0
+ MX27_PAD_USBH1_TXDP__UART4_CTS 0x0
+ MX27_PAD_USBH1_FS__UART4_RTS 0x0
+ >;
+ };
+
+ pinctrl_uart8250_1: uart82501grp {
+ fsl,pins = <
+ MX27_PAD_USB_PWR__GPIO2_23 0x0
+ >;
+ };
+
+ pinctrl_uart8250_2: uart82502grp {
+ fsl,pins = <
+ MX27_PAD_USBH1_SUSP__GPIO2_22 0x0
+ >;
+ };
+
+ pinctrl_uart8250_3: uart82503grp {
+ fsl,pins = <
+ MX27_PAD_USBH1_OE_B__GPIO2_27 0x0
+ >;
+ };
+
+ pinctrl_uart8250_4: uart82504grp {
+ fsl,pins = <
+ MX27_PAD_USBH1_RXDM__GPIO2_30 0x0
+ >;
+ };
+
+ pinctrl_usbh2: usbh2grp {
+ fsl,pins = <
+ MX27_PAD_USBH2_CLK__USBH2_CLK 0x0
+ MX27_PAD_USBH2_DIR__USBH2_DIR 0x0
+ MX27_PAD_USBH2_NXT__USBH2_NXT 0x0
+ MX27_PAD_USBH2_STP__USBH2_STP 0x0
+ MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x0
+ MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x0
+ MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x0
+ MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x0
+ MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x0
+ MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x0
+ MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x0
+ MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x0
+ MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x0
+ MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x0
+ MX27_PAD_USBOTG_STP__USBOTG_STP 0x0
+ MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x0
+ MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x0
+ MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x0
+ MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x0
+ MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x0
+ MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x0
+ MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x0
+ MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x0
+ >;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,274 @@
+/*
+ * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx27-eukrea-cpuimx27.dtsi"
+
+/ {
+ model = "Eukrea MBIMXSD27";
+ compatible = "eukrea,mbimxsd27-baseboard", "eukrea,cpuimx27", "fsl,imx27";
+
+ display0: CMO-QVGA {
+ model = "CMO-QVGA";
+ native-mode = <&timing0>;
+ bits-per-pixel = <16>;
+ fsl,pcr = <0xfad08b80>;
+
+ display-timings {
+ timing0: 320x240 {
+ clock-frequency = <6500000>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <20>;
+ hsync-len = <30>;
+ hfront-porch = <38>;
+ vback-porch = <4>;
+ vsync-len = <3>;
+ vfront-porch = <15>;
+ };
+ };
+ };
+
+ backlight {
+ compatible = "gpio-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds>;
+
+ led1 {
+ label = "system::live";
+ gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "system::user";
+ gpios = <&gpio6 19 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "simple-bus";
+
+ reg_lcd: regulator@0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdreg>;
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "LCD";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+};
+
+&cspi1 {
+ pinctrl-0 = <&pinctrl_cspi1>;
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ ads7846 {
+ compatible = "ti,ads7846";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_touch>;
+ reg = <0>;
+ interrupts = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>;
+ spi-cpol;
+ spi-max-frequency = <1500000>;
+ ti,keep-vref-on;
+ };
+};
+
+&fb {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_imxfb>;
+ display = <&display0>;
+ lcd-supply = <®_lcd>;
+ fsl,dmacr = <0x00040060>;
+ fsl,lscr1 = <0x00120300>;
+ fsl,lpccr = <0x00a903ff>;
+ status = "okay";
+};
+
+&i2c1 {
+ codec: codec@1a {
+ compatible = "ti,tlv320aic23";
+ reg = <0x1a>;
+ };
+};
+
+&kpp {
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_UP)
+ MATRIX_KEY(0, 1, KEY_DOWN)
+ MATRIX_KEY(1, 0, KEY_RIGHT)
+ MATRIX_KEY(1, 1, KEY_LEFT)
+ >;
+ status = "okay";
+};
+
+&sdhci1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhc1>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssi1>;
+ fsl,mode = "i2s-slave";
+ codec-handle = <&codec>;
+ status = "okay";
+};
+
+&uart1 {
+ fsl,uart-has-rtscts;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ fsl,uart-has-rtscts;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ fsl,uart-has-rtscts;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&iomuxc {
+ imx27-eukrea-cpuimx27-baseboard {
+ pinctrl_cspi1: cspi1grp {
+ fsl,pins = <
+ MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x0
+ MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x0
+ MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x0
+ MX27_PAD_CSPI1_SS0__GPIO4_28 0x0 /* CS0 */
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX27_PAD_PWMO__GPIO5_5 0x0
+ >;
+ };
+
+ pinctrl_gpioleds: gpioledsgrp {
+ fsl,pins = <
+ MX27_PAD_PC_PWRON__GPIO6_16 0x0
+ MX27_PAD_PC_CD2_B__GPIO6_19 0x0
+ >;
+ };
+
+ pinctrl_imxfb: imxfbgrp {
+ fsl,pins = <
+ MX27_PAD_LD0__LD0 0x0
+ MX27_PAD_LD1__LD1 0x0
+ MX27_PAD_LD2__LD2 0x0
+ MX27_PAD_LD3__LD3 0x0
+ MX27_PAD_LD4__LD4 0x0
+ MX27_PAD_LD5__LD5 0x0
+ MX27_PAD_LD6__LD6 0x0
+ MX27_PAD_LD7__LD7 0x0
+ MX27_PAD_LD8__LD8 0x0
+ MX27_PAD_LD9__LD9 0x0
+ MX27_PAD_LD10__LD10 0x0
+ MX27_PAD_LD11__LD11 0x0
+ MX27_PAD_LD12__LD12 0x0
+ MX27_PAD_LD13__LD13 0x0
+ MX27_PAD_LD14__LD14 0x0
+ MX27_PAD_LD15__LD15 0x0
+ MX27_PAD_LD16__LD16 0x0
+ MX27_PAD_LD17__LD17 0x0
+ MX27_PAD_CONTRAST__CONTRAST 0x0
+ MX27_PAD_OE_ACD__OE_ACD 0x0
+ MX27_PAD_HSYNC__HSYNC 0x0
+ MX27_PAD_VSYNC__VSYNC 0x0
+ >;
+ };
+
+ pinctrl_lcdreg: lcdreggrp {
+ fsl,pins = <
+ MX27_PAD_CLS__GPIO1_25 0x0
+ >;
+ };
+
+ pinctrl_sdhc1: sdhc1grp {
+ fsl,pins = <
+ MX27_PAD_SD1_CLK__SD1_CLK 0x0
+ MX27_PAD_SD1_CMD__SD1_CMD 0x0
+ MX27_PAD_SD1_D0__SD1_D0 0x0
+ MX27_PAD_SD1_D1__SD1_D1 0x0
+ MX27_PAD_SD1_D2__SD1_D2 0x0
+ MX27_PAD_SD1_D3__SD1_D3 0x0
+ >;
+ };
+
+ pinctrl_ssi1: ssi1grp {
+ fsl,pins = <
+ MX27_PAD_SSI4_CLK__SSI4_CLK 0x0
+ MX27_PAD_SSI4_FS__SSI4_FS 0x0
+ MX27_PAD_SSI4_RXDAT__SSI4_RXDAT 0x1
+ MX27_PAD_SSI4_TXDAT__SSI4_TXDAT 0x1
+ >;
+ };
+
+ pinctrl_touch: touchgrp {
+ fsl,pins = <
+ MX27_PAD_CSPI1_RDY__GPIO4_25 0x0 /* IRQ */
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX27_PAD_UART1_TXD__UART1_TXD 0x0
+ MX27_PAD_UART1_RXD__UART1_RXD 0x0
+ MX27_PAD_UART1_CTS__UART1_CTS 0x0
+ MX27_PAD_UART1_RTS__UART1_RTS 0x0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX27_PAD_UART2_TXD__UART2_TXD 0x0
+ MX27_PAD_UART2_RXD__UART2_RXD 0x0
+ MX27_PAD_UART2_CTS__UART2_CTS 0x0
+ MX27_PAD_UART2_RTS__UART2_RTS 0x0
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX27_PAD_UART3_TXD__UART3_TXD 0x0
+ MX27_PAD_UART3_RXD__UART3_RXD 0x0
+ MX27_PAD_UART3_CTS__UART3_CTS 0x0
+ MX27_PAD_UART3_RTS__UART3_RTS 0x0
+ >;
+ };
+ };
+};
This patch adds support for the cpuimx27 board from Eukrea and its baseboard. This change is intended to further remove non-DT support for this board. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi | 296 +++++++++++++++++++++ .../boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts | 274 +++++++++++++++++++ 3 files changed, 571 insertions(+) create mode 100644 arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi create mode 100644 arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts