| Message ID | 201405270217.33057.sergei.shtylyov@cogentembedded.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
On Tue, May 27, 2014 at 7:17 AM, Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> wrote: > Describe the PCI USB devices that are behind the PCI bridges, adding necessary > links to the USB PHY device. > > Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. > > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > > --- > This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon Horman's > 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches posted > before. The patch requires the internal PCI DT support, USB PHY driver, and > USB HCD generic PHY support (also already posted) in order to work. > > Changes in version 2: > - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding; > - changed the PHY specifier in the PCI#2 node to reflect that channel #1 support > was dropped; > - resolved rejects, refreshed the patch. > > arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ > 1 file changed, 28 insertions(+) > > Index: renesas/arch/arm/boot/dts/r8a7790.dtsi > =================================================================== > --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi > +++ renesas/arch/arm/boot/dts/r8a7790.dtsi > @@ -919,6 +919,20 @@ > interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH > 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH > 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; > + > + usb@0,1 { > + reg = <0x800 0 0 0 0>; > + device_type = "pci"; > + phys = <&usbphy 0 0>; > + phy-names = "usb"; > + }; > + > + usb@0,2 { > + reg = <0x1000 0 0 0 0>; > + device_type = "pci"; > + phys = <&usbphy 0 0>; > + phy-names = "usb"; > + }; > }; > > pci1: pci@ee0b0000 { > @@ -955,5 +969,19 @@ > interrupt-map = <0x0000 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH > 0x0800 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH > 0x1000 0 0 2 &gic 0 113 IRQ_TYPE_LEVEL_HIGH>; > + > + usb@0,1 { > + reg = <0x800 0 0 0 0>; > + device_type = "pci"; > + phys = <&usbphy 1 0>; > + phy-names = "usb"; > + }; > + > + usb@0,2 { > + reg = <0x1000 0 0 0 0>; > + device_type = "pci"; > + phys = <&usbphy 1 0>; > + phy-names = "usb"; > + }; > }; > }; Hi Sergei, Above I see two hunks of DTS code but my r8a7790 data sheet contains three USB PCI devices. Perhaps my understanding is wrong, or may there is some other patch available to enable all USB PCI devices included in the SoC? Thanks, / magnus -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 05/27/2014 02:36 AM, Magnus Damm wrote: >> Describe the PCI USB devices that are behind the PCI bridges, adding necessary >> links to the USB PHY device. >> Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. >> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> >> --- >> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon Horman's >> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches posted >> before. The patch requires the internal PCI DT support, USB PHY driver, and >> USB HCD generic PHY support (also already posted) in order to work. >> Changes in version 2: >> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding; >> - changed the PHY specifier in the PCI#2 node to reflect that channel #1 support >> was dropped; >> - resolved rejects, refreshed the patch. >> arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ >> 1 file changed, 28 insertions(+) >> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi >> =================================================================== >> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi >> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi >> @@ -919,6 +919,20 @@ >> interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH >> 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH >> 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; >> + >> + usb@0,1 { >> + reg = <0x800 0 0 0 0>; >> + device_type = "pci"; >> + phys = <&usbphy 0 0>; >> + phy-names = "usb"; >> + }; >> + >> + usb@0,2 { >> + reg = <0x1000 0 0 0 0>; >> + device_type = "pci"; >> + phys = <&usbphy 0 0>; >> + phy-names = "usb"; >> + }; >> }; >> >> pci1: pci@ee0b0000 { >> @@ -955,5 +969,19 @@ >> interrupt-map = <0x0000 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH >> 0x0800 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH >> 0x1000 0 0 2 &gic 0 113 IRQ_TYPE_LEVEL_HIGH>; >> + >> + usb@0,1 { >> + reg = <0x800 0 0 0 0>; >> + device_type = "pci"; >> + phys = <&usbphy 1 0>; >> + phy-names = "usb"; >> + }; >> + >> + usb@0,2 { >> + reg = <0x1000 0 0 0 0>; >> + device_type = "pci"; >> + phys = <&usbphy 1 0>; >> + phy-names = "usb"; >> + }; >> }; >> }; > Hi Sergei, > Above I see two hunks of DTS code but my r8a7790 data sheet contains > three USB PCI devices. Perhaps my understanding is wrong, or may there You probably wanted to say 6 (OHCI and EHCI are 2 different PCI devices). > is some other patch available to enable all USB PCI devices included > in the SoC? This patch doesn't enable USB devices, it just links them to the PHY where it makes sense (for USB channel #1 it doesn't). > Thanks, > / magnus WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, May 27, 2014 at 7:46 AM, Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> wrote: > On 05/27/2014 02:36 AM, Magnus Damm wrote: > >>> Describe the PCI USB devices that are behind the PCI bridges, adding >>> necessary >>> links to the USB PHY device. > > >>> Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. > > >>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > > >>> --- >>> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon >>> Horman's >>> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches >>> posted >>> before. The patch requires the internal PCI DT support, USB PHY driver, >>> and >>> USB HCD generic PHY support (also already posted) in order to work. > > >>> Changes in version 2: >>> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding; >>> - changed the PHY specifier in the PCI#2 node to reflect that channel #1 >>> support >>> was dropped; >>> - resolved rejects, refreshed the patch. > > >>> arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ >>> 1 file changed, 28 insertions(+) > > >>> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi >>> =================================================================== >>> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi >>> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi >>> @@ -919,6 +919,20 @@ >>> interrupt-map = <0x0000 0 0 1 &gic 0 108 >>> IRQ_TYPE_LEVEL_HIGH >>> 0x0800 0 0 1 &gic 0 108 >>> IRQ_TYPE_LEVEL_HIGH >>> 0x1000 0 0 2 &gic 0 108 >>> IRQ_TYPE_LEVEL_HIGH>; >>> + >>> + usb@0,1 { >>> + reg = <0x800 0 0 0 0>; >>> + device_type = "pci"; >>> + phys = <&usbphy 0 0>; >>> + phy-names = "usb"; >>> + }; >>> + >>> + usb@0,2 { >>> + reg = <0x1000 0 0 0 0>; >>> + device_type = "pci"; >>> + phys = <&usbphy 0 0>; >>> + phy-names = "usb"; >>> + }; >>> }; >>> >>> pci1: pci@ee0b0000 { >>> @@ -955,5 +969,19 @@ >>> interrupt-map = <0x0000 0 0 1 &gic 0 113 >>> IRQ_TYPE_LEVEL_HIGH >>> 0x0800 0 0 1 &gic 0 113 >>> IRQ_TYPE_LEVEL_HIGH >>> 0x1000 0 0 2 &gic 0 113 >>> IRQ_TYPE_LEVEL_HIGH>; >>> + >>> + usb@0,1 { >>> + reg = <0x800 0 0 0 0>; >>> + device_type = "pci"; >>> + phys = <&usbphy 1 0>; >>> + phy-names = "usb"; >>> + }; >>> + >>> + usb@0,2 { >>> + reg = <0x1000 0 0 0 0>; >>> + device_type = "pci"; >>> + phys = <&usbphy 1 0>; >>> + phy-names = "usb"; >>> + }; >>> }; >>> }; > > >> Hi Sergei, > > >> Above I see two hunks of DTS code but my r8a7790 data sheet contains >> three USB PCI devices. Perhaps my understanding is wrong, or may there > > > You probably wanted to say 6 (OHCI and EHCI are 2 different PCI devices). Sure. I guess it depends on if you count PCI host controllers or USB host controllers.. >> is some other patch available to enable all USB PCI devices included >> in the SoC? > > > This patch doesn't enable USB devices, it just links them to the PHY > where it makes sense (for USB channel #1 it doesn't). I know we've discussed this before, and for USB channel #1 you tend to say that the PHY is not necessary for operation. From my side I am not so sure. Over the months I seen several shortcuts and missing pieces so for now just assume this is another rushed attempt. As usual I would like to make sure the dependencies are correctly described in DT before merging anything. Like I mentioned earlier there are shared bits in UGCTRL register in the PHY. Those may or may not affect USB channel #1. Furthermore, on top of this we have the MSTP bit for the PHY that may or may not be related to USB channel #1. My opinion is that if the USB PHY requires the MSTP clock to be enabled when using USB channel #1 _or_ the UGCTRL bits affect the USB Channel #1 then DT needs to point out the relationship between the PHY and the USB Host so Runtime PM can be used in the PHY driver to dynamically manage the clock. Thanks, / magnus -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 05/27/2014 04:41 AM, Magnus Damm wrote: >>>> Describe the PCI USB devices that are behind the PCI bridges, adding >>>> necessary >>>> links to the USB PHY device. >>>> Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. >>>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> >>>> --- >>>> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon >>>> Horman's >>>> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches >>>> posted >>>> before. The patch requires the internal PCI DT support, USB PHY driver, >>>> and >>>> USB HCD generic PHY support (also already posted) in order to work. >>>> Changes in version 2: >>>> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding; >>>> - changed the PHY specifier in the PCI#2 node to reflect that channel #1 >>>> support >>>> was dropped; >>>> - resolved rejects, refreshed the patch. >>>> arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ >>>> 1 file changed, 28 insertions(+) >>>> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi >>>> =================================================================== >>>> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi >>>> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi >>>> @@ -919,6 +919,20 @@ >>>> interrupt-map = <0x0000 0 0 1 &gic 0 108 >>>> IRQ_TYPE_LEVEL_HIGH >>>> 0x0800 0 0 1 &gic 0 108 >>>> IRQ_TYPE_LEVEL_HIGH >>>> 0x1000 0 0 2 &gic 0 108 >>>> IRQ_TYPE_LEVEL_HIGH>; >>>> + >>>> + usb@0,1 { >>>> + reg = <0x800 0 0 0 0>; >>>> + device_type = "pci"; >>>> + phys = <&usbphy 0 0>; >>>> + phy-names = "usb"; >>>> + }; >>>> + >>>> + usb@0,2 { >>>> + reg = <0x1000 0 0 0 0>; >>>> + device_type = "pci"; >>>> + phys = <&usbphy 0 0>; >>>> + phy-names = "usb"; >>>> + }; >>>> }; >>>> >>>> pci1: pci@ee0b0000 { >>>> @@ -955,5 +969,19 @@ >>>> interrupt-map = <0x0000 0 0 1 &gic 0 113 >>>> IRQ_TYPE_LEVEL_HIGH >>>> 0x0800 0 0 1 &gic 0 113 >>>> IRQ_TYPE_LEVEL_HIGH >>>> 0x1000 0 0 2 &gic 0 113 >>>> IRQ_TYPE_LEVEL_HIGH>; >>>> + >>>> + usb@0,1 { >>>> + reg = <0x800 0 0 0 0>; >>>> + device_type = "pci"; >>>> + phys = <&usbphy 1 0>; >>>> + phy-names = "usb"; >>>> + }; >>>> + >>>> + usb@0,2 { >>>> + reg = <0x1000 0 0 0 0>; >>>> + device_type = "pci"; >>>> + phys = <&usbphy 1 0>; >>>> + phy-names = "usb"; >>>> + }; >>>> }; >>>> }; >>> Hi Sergei, >>> Above I see two hunks of DTS code but my r8a7790 data sheet contains >>> three USB PCI devices. Perhaps my understanding is wrong, or may there >> You probably wanted to say 6 (OHCI and EHCI are 2 different PCI devices). > Sure. I guess it depends on if you count PCI host controllers or USB > host controllers.. You said "USB PCI devices", so I thought you meant the latter. >>> is some other patch available to enable all USB PCI devices included >>> in the SoC? >> This patch doesn't enable USB devices, it just links them to the PHY >> where it makes sense (for USB channel #1 it doesn't). > I know we've discussed this before, and for USB channel #1 you tend to > say that the PHY is not necessary for operation. From my side I am not > so sure. Over the months I seen several shortcuts and missing pieces > so for now just assume this is another rushed attempt. As usual I > would like to make sure the dependencies are correctly described in DT > before merging anything. > Like I mentioned earlier there are shared bits in UGCTRL register in Did you mean UGCTRL or UGCTRL2 register? My testing didn't prove that the UGCTRL bits (CONNECT and PLLRESET) affect anything but the USBHS controller -- my PHY driver only touches these bits if the PHY selected corresponds to the USBHS itself (which is not supported by DT yet)... > the PHY. Those may or may not affect USB channel #1. Furthermore, on > top of this we have the MSTP bit for the PHY that may or may not be > related to USB channel #1. There is no MSTP bit for the PHY, there's MSTP bit for USBHS controller of which this PHY is a part. > My opinion is that if the USB PHY requires the MSTP clock to be > enabled when using USB channel #1 _or_ the UGCTRL bits affect the USB > Channel #1 then DT needs to point out the relationship between the PHY > and the USB Host I agree and I can conduct some additional tests only linking the USB channel #1 to the PHY driver, and hence enabling the USBHS clock only for it... > so Runtime PM can be used in the PHY driver to > dynamically manage the clock. Er, do you insist on using the runtime PM vs clock API? I'm not yet sure it'll work with a named clock... > Thanks, > / magnus WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 05/29/2014 01:51 AM, Sergei Shtylyov wrote: >>>>> Describe the PCI USB devices that are behind the PCI bridges, adding >>>>> necessary >>>>> links to the USB PHY device. >>>>> Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. >>>>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> >>>>> --- >>>>> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon >>>>> Horman's >>>>> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches >>>>> posted >>>>> before. The patch requires the internal PCI DT support, USB PHY driver, >>>>> and >>>>> USB HCD generic PHY support (also already posted) in order to work. >>>>> Changes in version 2: >>>>> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding; >>>>> - changed the PHY specifier in the PCI#2 node to reflect that channel #1 >>>>> support >>>>> was dropped; >>>>> - resolved rejects, refreshed the patch. >>>>> arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ >>>>> 1 file changed, 28 insertions(+) >>>>> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi >>>>> =================================================================== >>>>> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi >>>>> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi >>>>> @@ -919,6 +919,20 @@ >>>>> interrupt-map = <0x0000 0 0 1 &gic 0 108 >>>>> IRQ_TYPE_LEVEL_HIGH >>>>> 0x0800 0 0 1 &gic 0 108 >>>>> IRQ_TYPE_LEVEL_HIGH >>>>> 0x1000 0 0 2 &gic 0 108 >>>>> IRQ_TYPE_LEVEL_HIGH>; >>>>> + >>>>> + usb@0,1 { >>>>> + reg = <0x800 0 0 0 0>; >>>>> + device_type = "pci"; >>>>> + phys = <&usbphy 0 0>; >>>>> + phy-names = "usb"; >>>>> + }; >>>>> + >>>>> + usb@0,2 { >>>>> + reg = <0x1000 0 0 0 0>; >>>>> + device_type = "pci"; >>>>> + phys = <&usbphy 0 0>; >>>>> + phy-names = "usb"; >>>>> + }; >>>>> }; >>>>> >>>>> pci1: pci@ee0b0000 { >>>>> @@ -955,5 +969,19 @@ >>>>> interrupt-map = <0x0000 0 0 1 &gic 0 113 >>>>> IRQ_TYPE_LEVEL_HIGH >>>>> 0x0800 0 0 1 &gic 0 113 >>>>> IRQ_TYPE_LEVEL_HIGH >>>>> 0x1000 0 0 2 &gic 0 113 >>>>> IRQ_TYPE_LEVEL_HIGH>; >>>>> + >>>>> + usb@0,1 { >>>>> + reg = <0x800 0 0 0 0>; >>>>> + device_type = "pci"; >>>>> + phys = <&usbphy 1 0>; >>>>> + phy-names = "usb"; >>>>> + }; >>>>> + >>>>> + usb@0,2 { >>>>> + reg = <0x1000 0 0 0 0>; >>>>> + device_type = "pci"; >>>>> + phys = <&usbphy 1 0>; >>>>> + phy-names = "usb"; >>>>> + }; >>>>> }; >>>>> }; [...] >> I know we've discussed this before, and for USB channel #1 you tend to >> say that the PHY is not necessary for operation. From my side I am not >> so sure. Over the months I seen several shortcuts and missing pieces >> so for now just assume this is another rushed attempt. As usual I >> would like to make sure the dependencies are correctly described in DT >> before merging anything. >> Like I mentioned earlier there are shared bits in UGCTRL register in > Did you mean UGCTRL or UGCTRL2 register? My testing didn't prove that the > UGCTRL bits (CONNECT and PLLRESET) affect anything but the USBHS controller -- > my PHY driver only touches these bits if the PHY selected corresponds to the > USBHS itself (which is not supported by DT yet)... >> the PHY. Those may or may not affect USB channel #1. Furthermore, on >> top of this we have the MSTP bit for the PHY that may or may not be >> related to USB channel #1. > There is no MSTP bit for the PHY, there's MSTP bit for USBHS controller of > which this PHY is a part. >> My opinion is that if the USB PHY requires the MSTP clock to be >> enabled when using USB channel #1 _or_ the UGCTRL bits affect the USB >> Channel #1 then DT needs to point out the relationship between the PHY >> and the USB Host > I agree and I can conduct some additional tests only linking the USB > channel #1 to the PHY driver, and hence enabling the USBHS clock only for it... OK, I've done additional testing and USB channel #1 on R8A7790 works regardless of the USBHS clock being enabled or not. >> Thanks, >> / magnus WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Jun 5, 2014 at 5:03 AM, Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> wrote: > Hello. > > > On 05/29/2014 01:51 AM, Sergei Shtylyov wrote: > >>>>>> Describe the PCI USB devices that are behind the PCI bridges, adding >>>>>> necessary >>>>>> links to the USB PHY device. > > >>>>>> Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. > > >>>>>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > > >>>>>> --- >>>>>> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon >>>>>> Horman's >>>>>> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches >>>>>> posted >>>>>> before. The patch requires the internal PCI DT support, USB PHY >>>>>> driver, >>>>>> and >>>>>> USB HCD generic PHY support (also already posted) in order to work. > > >>>>>> Changes in version 2: >>>>>> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI >>>>>> binding; >>>>>> - changed the PHY specifier in the PCI#2 node to reflect that channel >>>>>> #1 >>>>>> support >>>>>> was dropped; >>>>>> - resolved rejects, refreshed the patch. > > >>>>>> arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ >>>>>> 1 file changed, 28 insertions(+) > > >>>>>> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi >>>>>> =================================================================== >>>>>> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi >>>>>> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi >>>>>> @@ -919,6 +919,20 @@ >>>>>> interrupt-map = <0x0000 0 0 1 &gic 0 108 >>>>>> IRQ_TYPE_LEVEL_HIGH >>>>>> 0x0800 0 0 1 &gic 0 108 >>>>>> IRQ_TYPE_LEVEL_HIGH >>>>>> 0x1000 0 0 2 &gic 0 108 >>>>>> IRQ_TYPE_LEVEL_HIGH>; >>>>>> + >>>>>> + usb@0,1 { >>>>>> + reg = <0x800 0 0 0 0>; >>>>>> + device_type = "pci"; >>>>>> + phys = <&usbphy 0 0>; >>>>>> + phy-names = "usb"; >>>>>> + }; >>>>>> + >>>>>> + usb@0,2 { >>>>>> + reg = <0x1000 0 0 0 0>; >>>>>> + device_type = "pci"; >>>>>> + phys = <&usbphy 0 0>; >>>>>> + phy-names = "usb"; >>>>>> + }; >>>>>> }; >>>>>> >>>>>> pci1: pci@ee0b0000 { >>>>>> @@ -955,5 +969,19 @@ >>>>>> interrupt-map = <0x0000 0 0 1 &gic 0 113 >>>>>> IRQ_TYPE_LEVEL_HIGH >>>>>> 0x0800 0 0 1 &gic 0 113 >>>>>> IRQ_TYPE_LEVEL_HIGH >>>>>> 0x1000 0 0 2 &gic 0 113 >>>>>> IRQ_TYPE_LEVEL_HIGH>; >>>>>> + >>>>>> + usb@0,1 { >>>>>> + reg = <0x800 0 0 0 0>; >>>>>> + device_type = "pci"; >>>>>> + phys = <&usbphy 1 0>; >>>>>> + phy-names = "usb"; >>>>>> + }; >>>>>> + >>>>>> + usb@0,2 { >>>>>> + reg = <0x1000 0 0 0 0>; >>>>>> + device_type = "pci"; >>>>>> + phys = <&usbphy 1 0>; >>>>>> + phy-names = "usb"; >>>>>> + }; >>>>>> }; >>>>>> }; > > > [...] > > >>> I know we've discussed this before, and for USB channel #1 you tend to >>> say that the PHY is not necessary for operation. From my side I am not >>> so sure. Over the months I seen several shortcuts and missing pieces >>> so for now just assume this is another rushed attempt. As usual I >>> would like to make sure the dependencies are correctly described in DT >>> before merging anything. > > >>> Like I mentioned earlier there are shared bits in UGCTRL register in > > >> Did you mean UGCTRL or UGCTRL2 register? My testing didn't prove that >> the >> UGCTRL bits (CONNECT and PLLRESET) affect anything but the USBHS >> controller -- >> my PHY driver only touches these bits if the PHY selected corresponds to >> the >> USBHS itself (which is not supported by DT yet)... > > >>> the PHY. Those may or may not affect USB channel #1. Furthermore, on >>> top of this we have the MSTP bit for the PHY that may or may not be >>> related to USB channel #1. > > >> There is no MSTP bit for the PHY, there's MSTP bit for USBHS >> controller of >> which this PHY is a part. > > >>> My opinion is that if the USB PHY requires the MSTP clock to be >>> enabled when using USB channel #1 _or_ the UGCTRL bits affect the USB >>> Channel #1 then DT needs to point out the relationship between the PHY >>> and the USB Host > > >> I agree and I can conduct some additional tests only linking the USB >> channel #1 to the PHY driver, and hence enabling the USBHS clock only for >> it... > > > OK, I've done additional testing and USB channel #1 on R8A7790 works > regardless of the USBHS clock being enabled or not. Thanks for testing! So I suppose this means that we can manage the USB PHY clock used for channel #0 and #2 independently of channel #1? Cheers, / magnus -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Index: renesas/arch/arm/boot/dts/r8a7790.dtsi =================================================================== --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi +++ renesas/arch/arm/boot/dts/r8a7790.dtsi @@ -919,6 +919,20 @@ interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + usb@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + + usb@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; }; pci1: pci@ee0b0000 { @@ -955,5 +969,19 @@ interrupt-map = <0x0000 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH 0x0800 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH 0x1000 0 0 2 &gic 0 113 IRQ_TYPE_LEVEL_HIGH>; + + usb@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 1 0>; + phy-names = "usb"; + }; + + usb@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 1 0>; + phy-names = "usb"; + }; }; };
Describe the PCI USB devices that are behind the PCI bridges, adding necessary links to the USB PHY device. Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> --- This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon Horman's 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches posted before. The patch requires the internal PCI DT support, USB PHY driver, and USB HCD generic PHY support (also already posted) in order to work. Changes in version 2: - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding; - changed the PHY specifier in the PCI#2 node to reflect that channel #1 support was dropped; - resolved rejects, refreshed the patch. arch/arm/boot/dts/r8a7790.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html