@@ -165,6 +165,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx27-apf27.dtb \
imx27-apf27dev.dtb \
imx27-eukrea-mbimxsd27-baseboard.dtb \
+ imx27-ipcam.dtb \
imx27-pdk.dtb \
imx27-phytec-phycore-rdk.dtb \
imx27-phytec-phycard-s-rdk.dtb \
new file mode 100644
@@ -0,0 +1,106 @@
+/*
+ * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx27.dtsi"
+
+/ {
+ model = "Freescale i.MX27 IP Camera";
+ compatible = "fsl,imx27-ipcam", "fsl,imx27";
+
+ memory {
+ reg = <0xa0000000 0x04000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ osc26m {
+ compatible = "fsl,imx-osc26m", "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_5v0: regulator@0 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg5v0>;
+ reg = <0>;
+ regulator-name = "5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio6 9 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "mii";
+ phy-reset-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&iomuxc {
+ imx27-ipcam {
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX27_PAD_SD3_CMD__FEC_TXD0 0x0
+ MX27_PAD_SD3_CLK__FEC_TXD1 0x0
+ MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
+ MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
+ MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
+ MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
+ MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
+ MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
+ MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
+ MX27_PAD_ATA_DATA7__FEC_MDC 0x0
+ MX27_PAD_ATA_DATA8__FEC_CRS 0x0
+ MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
+ MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
+ MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
+ MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
+ MX27_PAD_ATA_DATA13__FEC_COL 0x0
+ MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
+ MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
+ MX27_PAD_USBH1_RXDP__GPIO2_31 0x0 /* RST */
+ >;
+ };
+
+ pinctrl_reg5v0: reg5v0grp {
+ fsl,pins = <
+ MX27_PAD_IOIS16__GPIO6_9 0x0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX27_PAD_UART1_TXD__UART1_TXD 0x0
+ MX27_PAD_UART1_RXD__UART1_RXD 0x0
+ >;
+ };
+ };
+};
@@ -397,15 +397,6 @@ config MACH_MXT_TD60
Include support for i-MXT (aka td60) platform. This
includes specific configurations for the module and its peripherals.
-config MACH_IMX27IPCAM
- bool "IMX27 IPCAM platform"
- select IMX_HAVE_PLATFORM_IMX2_WDT
- select IMX_HAVE_PLATFORM_IMX_UART
- select SOC_IMX27
- help
- Include support for IMX27 IPCAM platform. This includes specific
- configurations for the board and its peripherals.
-
config MACH_IMX27_DT
bool "Support i.MX27 platforms from device tree"
select SOC_IMX27
@@ -66,7 +66,6 @@ obj-$(CONFIG_MACH_CPUIMX27) += mach-cpuimx27.o
obj-$(CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD) += eukrea_mbimx27-baseboard.o
obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
obj-$(CONFIG_MACH_MXT_TD60) += mach-mxt_td60.o
-obj-$(CONFIG_MACH_IMX27IPCAM) += mach-imx27ipcam.o
obj-$(CONFIG_MACH_IMX27_DT) += imx27-dt.o
# i.MX31 based machines
deleted file mode 100644
@@ -1,77 +0,0 @@
-/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "hardware.h"
-#include "common.h"
-#include "devices-imx27.h"
-#include "iomux-mx27.h"
-
-static const int mx27ipcam_pins[] __initconst = {
- /* UART1 */
- PE12_PF_UART1_TXD,
- PE13_PF_UART1_RXD,
- /* FEC */
- PD0_AIN_FEC_TXD0,
- PD1_AIN_FEC_TXD1,
- PD2_AIN_FEC_TXD2,
- PD3_AIN_FEC_TXD3,
- PD4_AOUT_FEC_RX_ER,
- PD5_AOUT_FEC_RXD1,
- PD6_AOUT_FEC_RXD2,
- PD7_AOUT_FEC_RXD3,
- PD8_AF_FEC_MDIO,
- PD9_AIN_FEC_MDC,
- PD10_AOUT_FEC_CRS,
- PD11_AOUT_FEC_TX_CLK,
- PD12_AOUT_FEC_RXD0,
- PD13_AOUT_FEC_RX_DV,
- PD14_AOUT_FEC_RX_CLK,
- PD15_AOUT_FEC_COL,
- PD16_AIN_FEC_TX_ER,
- PF23_AIN_FEC_TX_EN,
-};
-
-static void __init mx27ipcam_init(void)
-{
- imx27_soc_init();
-
- mxc_gpio_setup_multiple_pins(mx27ipcam_pins, ARRAY_SIZE(mx27ipcam_pins),
- "mx27ipcam");
-
- imx27_add_imx_uart0(NULL);
- imx27_add_fec(NULL);
- imx27_add_imx2_wdt();
-}
-
-static void __init mx27ipcam_timer_init(void)
-{
- mx27_clocks_init(25000000);
-}
-
-MACHINE_START(IMX27IPCAM, "Freescale IMX27IPCAM")
- /* maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx27_map_io,
- .init_early = imx27_init_early,
- .init_irq = mx27_init_irq,
- .init_time = mx27ipcam_timer_init,
- .init_machine = mx27ipcam_init,
- .restart = mxc_restart,
-MACHINE_END
This patch adds a DT support for Freescale i.MX27 IP Camera board and removes platform representation for this board from the tree. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx27-ipcam.dts | 106 ++++++++++++++++++++++++++++++++++++ arch/arm/mach-imx/Kconfig | 9 --- arch/arm/mach-imx/Makefile | 1 - arch/arm/mach-imx/mach-imx27ipcam.c | 77 -------------------------- 5 files changed, 107 insertions(+), 87 deletions(-) create mode 100644 arch/arm/boot/dts/imx27-ipcam.dts delete mode 100644 arch/arm/mach-imx/mach-imx27ipcam.c