new file mode 100644
@@ -0,0 +1,131 @@
+Device tree binding for NVIDIA Tegra XUSB pad controller
+========================================================
+
+The Tegra XUSB pad controller manages a set of lanes, each of which can be
+assigned to one out of a set of different pads. Some of these pads have an
+associated PHY that must be powered up before the pad can be used.
+
+This document defines the device-specific binding for the XUSB pad controller.
+
+Refer to pinctrl-bindings.txt in this directory for generic information about
+pin controller device tree bindings and ../phy/phy-bindings.txt for details on
+how to describe and reference PHYs in device trees.
+
+Required properties:
+--------------------
+- compatible: should be "nvidia,tegra124-xusb-padctl"
+- reg: Physical base address and length of the controller's registers.
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - padctl
+- #address-cells: Should be 0.
+- #size-cells: Should be 0.
+- #phy-cells: Should be 1. The specifier is the index of the PHY to reference.
+ See <dt-bindings/pinctrl/pinctrl-tegra-xusb.h> for the list of valid values.
+
+Lane muxing:
+------------
+
+Child nodes contain the pinmux configurations following the conventions from
+the pinctrl-bindings.txt document. Typically a single, static configuration is
+given and applied at boot time.
+
+Each subnode describes groups of lanes along with parameters and pads that
+they should be assigned to. The name of these subnodes is not important. All
+subnodes should be parsed solely based on their content.
+
+Each subnode only applies the parameters that are explicitly listed. In other
+words, if a subnode that lists a function but no pin configuration parameters
+implies no information about any pin configuration parameters. Similarly, a
+subnode that describes only an IDDQ parameter implies no information about
+what function the pins are assigned to. For this reason even seemingly boolean
+values are actually tristates in this binding: unspecified, off or on.
+Unspecified is represented as an absent property, and off/on are represented
+as integer values 0 and 1.
+
+Required properties:
+- nvidia,lanes: An array of strings. Each string is the name of a lane.
+
+Optional properties:
+- nvidia,function: A string that is the name of the function (pad) that the
+ pin or group should be assigned to. Valid values for function names are
+ listed below.
+- nvidia,iddq: Enables IDDQ mode of the lane. (0: no, 1: yes)
+
+Note that not all of these properties are valid for all lanes. Lanes can be
+divided into three groups:
+
+ - otg-0, otg-1, otg-2:
+
+ Valid functions for this group are: "snps", "xusb", "uart", "rsvd".
+
+ The nvidia,iddq property does not apply to this group.
+
+ - ulpi-0, hsic-0, hsic-1:
+
+ Valid functions for this group are: "snps", "xusb".
+
+ The nvidia,iddq property does not apply to this group.
+
+ - pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, sata-0:
+
+ Valid functions for this group are: "pcie", "usb3", "sata", "rsvd".
+
+
+Example:
+========
+
+SoC file extract:
+-----------------
+
+ padctl@0,7009f000 {
+ compatible = "nvidia,tegra124-xusb-padctl";
+ reg = <0x0 0x7009f000 0x0 0x1000>;
+ resets = <&tegra_car 142>;
+ reset-names = "padctl";
+
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #phy-cells = <1>;
+ };
+
+Board file extract:
+-------------------
+
+ pcie-controller@0,01003000 {
+ ...
+
+ phys = <&padctl 0>;
+ phy-names = "pcie";
+
+ ...
+ };
+
+ ...
+
+ padctl: padctl@0,7009f000 {
+ pinctrl-0 = <&padctl_default>;
+ pinctrl-names = "default";
+
+ padctl_default: pinmux {
+ usb3 {
+ nvidia,lanes = "pcie-0", "pcie-1";
+ nvidia,function = "usb3";
+ nvidia,iddq = <0>;
+ };
+
+ pcie {
+ nvidia,lanes = "pcie-2", "pcie-3",
+ "pcie-4";
+ nvidia,function = "pcie";
+ nvidia,iddq = <0>;
+ };
+
+ sata {
+ nvidia,lanes = "sata-0";
+ nvidia,function = "sata";
+ nvidia,iddq = <0>;
+ };
+ };
+ };
new file mode 100644
@@ -0,0 +1,7 @@
+#ifndef _DT_BINDINGS_PINCTRL_TEGRA_XUSB_H
+#define _DT_BINDINGS_PINCTRL_TEGRA_XUSB_H 1
+
+#define TEGRA_XUSB_PADCTL_PCIE 0
+#define TEGRA_XUSB_PADCTL_SATA 1
+
+#endif /* _DT_BINDINGS_PINCTRL_TEGRA_XUSB_H */