| Message ID | 1405528686-16539-4-git-send-email-m-karicheri2@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
On Thu, Jul 17, 2014 at 12:38:04AM +0800, Murali Karicheri wrote: > keystone PCI controller is based on v3.65 designware hardware. This > version differs from newer versions of the hardware in few functional > areas discussed below that makes it necessary to change dw_pcie_host_init() > to support v3.65 based PCI controller. > > 1. No support for ATU port. So any ATU specific resource handling code > is to be bypassed for v3.65 h/w. > 2. MSI controller uses Application space to implement MSI and 32 MSI > interrupts are multiplexed over 8 IRQs to the host. Hence the code > to process MSI IRQ needs to be different. This patch allows platform > driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() > through an API callback from the designware core driver. > 3. MSI interrupt generation requires EP to write to the RC's application > register. So enhance the driver to allow setup of inbound access to > MSI irq register as a post scan bus API callback. > > Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Looks almost ok to me. Reviewed-by: Pratyush Anand <pratyush.anand@st.com> > int __init dw_pcie_host_init(struct pcie_port *pp) > { > struct device_node *np = pp->dev->of_node; > - struct of_pci_range range; > struct of_pci_range_parser parser; > + struct of_pci_range range; You may avoid moving the above line. ~Pratyush -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
> -----Original Message----- > From: Pratyush ANAND > Sent: Thursday, July 17, 2014 9:07 AM > To: Murali Karicheri > Cc: linux-pci@vger.kernel.org; linux-kernel@vger.kernel.org; linux-arm- > kernel@lists.infradead.org; Santosh Shilimkar; Russell King; Grant Likely; Rob > Herring; Mohit KUMAR DCG; Jingoo Han; Bjorn Helgaas; Richard Zhu; Kishon > Vijay Abraham I; Marek Vasut; Arnd Bergmann; Pawel Moll; Mark Rutland; > Ian Campbell; Kumar Gala; Randy Dunlap > Subject: Re: [PATCH v5 3/5] PCI: designware: enhance dw_pcie_host_init() > to support v3.65 DW hardware > > On Thu, Jul 17, 2014 at 12:38:04AM +0800, Murali Karicheri wrote: > > keystone PCI controller is based on v3.65 designware hardware. This > > version differs from newer versions of the hardware in few functional > > areas discussed below that makes it necessary to change > > dw_pcie_host_init() to support v3.65 based PCI controller. > > > > 1. No support for ATU port. So any ATU specific resource handling code > > is to be bypassed for v3.65 h/w. > > 2. MSI controller uses Application space to implement MSI and 32 MSI > > interrupts are multiplexed over 8 IRQs to the host. Hence the code > > to process MSI IRQ needs to be different. This patch allows platform > > driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() > > through an API callback from the designware core driver. > > 3. MSI interrupt generation requires EP to write to the RC's application > > register. So enhance the driver to allow setup of inbound access to > > MSI irq register as a post scan bus API callback. > > > > Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> > > Looks almost ok to me. > > Reviewed-by: Pratyush Anand <pratyush.anand@st.com> > - Now looks fine to me. Acked-by: Mohit KUMAR <mohit.kumar@st.com> Jingoo, After Murali's patches, dw code can be used by older Synopsys controller based driver too. Pls have a look at the series if you have any further comment. Thanks Mohit > > int __init dw_pcie_host_init(struct pcie_port *pp) { > > struct device_node *np = pp->dev->of_node; > > - struct of_pci_range range; > > struct of_pci_range_parser parser; > > + struct of_pci_range range; > > You may avoid moving the above line. > > ~Pratyush -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 07/16/2014 11:36 PM, Pratyush Anand wrote: > On Thu, Jul 17, 2014 at 12:38:04AM +0800, Murali Karicheri wrote: >> keystone PCI controller is based on v3.65 designware hardware. This >> version differs from newer versions of the hardware in few functional >> areas discussed below that makes it necessary to change dw_pcie_host_init() >> to support v3.65 based PCI controller. >> >> 1. No support for ATU port. So any ATU specific resource handling code >> is to be bypassed for v3.65 h/w. >> 2. MSI controller uses Application space to implement MSI and 32 MSI >> interrupts are multiplexed over 8 IRQs to the host. Hence the code >> to process MSI IRQ needs to be different. This patch allows platform >> driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() >> through an API callback from the designware core driver. >> 3. MSI interrupt generation requires EP to write to the RC's application >> register. So enhance the driver to allow setup of inbound access to >> MSI irq register as a post scan bus API callback. >> >> Signed-off-by: Murali Karicheri<m-karicheri2@ti.com> > Looks almost ok to me. > > Reviewed-by: Pratyush Anand<pratyush.anand@st.com> > >> int __init dw_pcie_host_init(struct pcie_port *pp) >> { >> struct device_node *np = pp->dev->of_node; >> - struct of_pci_range range; >> struct of_pci_range_parser parser; >> + struct of_pci_range range; > You may avoid moving the above line. Thought the variables are to be sorted. I can fix this when I resend it today with your reviewed by and Mohit's Ack. Regards, Murali > ~Pratyush -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 07/17/2014 12:18 AM, Mohit KUMAR DCG wrote: > > >> -----Original Message----- >> From: Pratyush ANAND >> Sent: Thursday, July 17, 2014 9:07 AM >> To: Murali Karicheri >> Cc: linux-pci@vger.kernel.org; linux-kernel@vger.kernel.org; linux-arm- >> kernel@lists.infradead.org; Santosh Shilimkar; Russell King; Grant Likely; Rob >> Herring; Mohit KUMAR DCG; Jingoo Han; Bjorn Helgaas; Richard Zhu; Kishon >> Vijay Abraham I; Marek Vasut; Arnd Bergmann; Pawel Moll; Mark Rutland; >> Ian Campbell; Kumar Gala; Randy Dunlap >> Subject: Re: [PATCH v5 3/5] PCI: designware: enhance dw_pcie_host_init() >> to support v3.65 DW hardware >> >> On Thu, Jul 17, 2014 at 12:38:04AM +0800, Murali Karicheri wrote: >>> keystone PCI controller is based on v3.65 designware hardware. This >>> version differs from newer versions of the hardware in few functional >>> areas discussed below that makes it necessary to change >>> dw_pcie_host_init() to support v3.65 based PCI controller. >>> >>> 1. No support for ATU port. So any ATU specific resource handling code >>> is to be bypassed for v3.65 h/w. >>> 2. MSI controller uses Application space to implement MSI and 32 MSI >>> interrupts are multiplexed over 8 IRQs to the host. Hence the code >>> to process MSI IRQ needs to be different. This patch allows platform >>> driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() >>> through an API callback from the designware core driver. >>> 3. MSI interrupt generation requires EP to write to the RC's application >>> register. So enhance the driver to allow setup of inbound access to >>> MSI irq register as a post scan bus API callback. >>> >>> Signed-off-by: Murali Karicheri<m-karicheri2@ti.com> >> >> Looks almost ok to me. >> >> Reviewed-by: Pratyush Anand<pratyush.anand@st.com> >> > > - Now looks fine to me. > > Acked-by: Mohit KUMAR<mohit.kumar@st.com> > > Jingoo, > After Murali's patches, dw code can be used by older Synopsys controller based driver too. > Pls have a look at the series if you have any further comment. > > Thanks > Mohit Mohit, Thanks for the review and Ack. Murali > >>> int __init dw_pcie_host_init(struct pcie_port *pp) { >>> struct device_node *np = pp->dev->of_node; >>> - struct of_pci_range range; >>> struct of_pci_range_parser parser; >>> + struct of_pci_range range; >> >> You may avoid moving the above line. >> >> ~Pratyush -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c index 905941c..e164fde 100644 --- a/drivers/pci/host/pcie-designware.c +++ b/drivers/pci/host/pcie-designware.c @@ -418,10 +418,10 @@ static const struct irq_domain_ops msi_domain_ops = { int __init dw_pcie_host_init(struct pcie_port *pp) { struct device_node *np = pp->dev->of_node; - struct of_pci_range range; struct of_pci_range_parser parser; + struct of_pci_range range; + int i, ret; u32 val; - int i; if (of_pci_range_parser_init(&parser, np)) { dev_err(pp->dev, "missing ranges property\n"); @@ -467,21 +467,26 @@ int __init dw_pcie_host_init(struct pcie_port *pp) } } - pp->cfg0_base = pp->cfg.start; - pp->cfg1_base = pp->cfg.start + pp->config.cfg0_size; pp->mem_base = pp->mem.start; - pp->va_cfg0_base = devm_ioremap(pp->dev, pp->cfg0_base, - pp->config.cfg0_size); if (!pp->va_cfg0_base) { - dev_err(pp->dev, "error with ioremap in function\n"); - return -ENOMEM; + pp->cfg0_base = pp->cfg.start; + pp->va_cfg0_base = devm_ioremap(pp->dev, pp->cfg0_base, + pp->config.cfg0_size); + if (!pp->va_cfg0_base) { + dev_err(pp->dev, "error with ioremap in function\n"); + return -ENOMEM; + } } - pp->va_cfg1_base = devm_ioremap(pp->dev, pp->cfg1_base, - pp->config.cfg1_size); + if (!pp->va_cfg1_base) { - dev_err(pp->dev, "error with ioremap\n"); - return -ENOMEM; + pp->cfg1_base = pp->cfg.start + pp->config.cfg0_size; + pp->va_cfg1_base = devm_ioremap(pp->dev, pp->cfg1_base, + pp->config.cfg1_size); + if (!pp->va_cfg1_base) { + dev_err(pp->dev, "error with ioremap\n"); + return -ENOMEM; + } } if (of_property_read_u32(np, "num-lanes", &pp->lanes)) { @@ -490,16 +495,22 @@ int __init dw_pcie_host_init(struct pcie_port *pp) } if (IS_ENABLED(CONFIG_PCI_MSI)) { - pp->irq_domain = irq_domain_add_linear(pp->dev->of_node, - MAX_MSI_IRQS, &msi_domain_ops, - &dw_pcie_msi_chip); - if (!pp->irq_domain) { - dev_err(pp->dev, "irq domain init failed\n"); - return -ENXIO; - } + if (!pp->ops->msi_host_init) { + pp->irq_domain = irq_domain_add_linear(pp->dev->of_node, + MAX_MSI_IRQS, &msi_domain_ops, + &dw_pcie_msi_chip); + if (!pp->irq_domain) { + dev_err(pp->dev, "irq domain init failed\n"); + return -ENXIO; + } - for (i = 0; i < MAX_MSI_IRQS; i++) - irq_create_mapping(pp->irq_domain, i); + for (i = 0; i < MAX_MSI_IRQS; i++) + irq_create_mapping(pp->irq_domain, i); + } else { + ret = pp->ops->msi_host_init(pp, &dw_pcie_msi_chip); + if (ret < 0) + return ret; + } } if (pp->ops->host_init) @@ -759,6 +770,9 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys) BUG(); } + if (bus && pp->ops->scan_bus) + pp->ops->scan_bus(pp); + return bus; } diff --git a/drivers/pci/host/pcie-designware.h b/drivers/pci/host/pcie-designware.h index 387f69e..080c649 100644 --- a/drivers/pci/host/pcie-designware.h +++ b/drivers/pci/host/pcie-designware.h @@ -70,6 +70,8 @@ struct pcie_host_ops { void (*msi_set_irq)(struct pcie_port *pp, int irq); void (*msi_clear_irq)(struct pcie_port *pp, int irq); u32 (*get_msi_data)(struct pcie_port *pp); + void (*scan_bus)(struct pcie_port *pp); + int (*msi_host_init)(struct pcie_port *pp, struct msi_chip *chip); }; int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val);
keystone PCI controller is based on v3.65 designware hardware. This version differs from newer versions of the hardware in few functional areas discussed below that makes it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. So any ATU specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses Application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the designware core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI irq register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Mohit Kumar <mohit.kumar@st.com> CC: Jingoo Han <jg1.han@samsung.com> CC: Bjorn Helgaas <bhelgaas@google.com> CC: Pratyush Anand <pratyush.anand@st.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org> --- drivers/pci/host/pcie-designware.c | 56 ++++++++++++++++++++++-------------- drivers/pci/host/pcie-designware.h | 2 ++ 2 files changed, 37 insertions(+), 21 deletions(-)