[v2,7/7] ASoC: fsl_sai: Configure dataline/FIFO information from dts property

Commit Message

Shengjiu Wang June 17, 2022, 7:44 a.m. UTC

The SAI has multiple successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive, so need
get such information from dts property "fsl,dataline"

fsl,dataline has 3 values for each configuration:
first one means the type: I2S(1) or DSD(2),
second one is dataline mask for 'rx',
third one is dataline mask for 'tx'.

Also set dma peripheral address and TRCE bits according to data lane.

Signed-off-by: Shengjiu Wang <[e-mail]>
Signed-off-by: Viorel Suman <[e-mail]>
---
 sound/soc/fsl/fsl_sai.c | 161 +++++++++++++++++++++++++++++++++++++++-
 sound/soc/fsl/fsl_sai.h |  17 +++++
 2 files changed, 174 insertions(+), 4 deletions(-)

Patch

diff --git a/sound/soc/fsl/fsl_sai.c b/sound/soc/fsl/fsl_sai.c
index 86aa0baba848..f5eabb0b10e8 100644
--- a/sound/soc/fsl/fsl_sai.c
+++ b/sound/soc/fsl/fsl_sai.c
@@ -487,13 +487,18 @@  static int fsl_sai_hw_params(struct snd_pcm_substream *substream,
 	unsigned int ofs = sai->soc_data->reg_offset;
 	bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
 	unsigned int channels = params_channels(params);
+	struct snd_dmaengine_dai_dma_data *dma_params;
+	struct fsl_sai_dl_cfg *dl_cfg = sai->dl_cfg;
 	u32 word_width = params_width(params);
+	int trce_mask = 0, dl_cfg_idx = 0;
+	int dl_cfg_cnt = sai->dl_cfg_cnt;
+	u32 dl_type = FSL_SAI_DL_I2S;
 	u32 val_cr4 = 0, val_cr5 = 0;
 	u32 slots = (channels == 1) ? 2 : channels;
 	u32 slot_width = word_width;
 	int adir = tx ? RX : TX;
 	u32 pins, bclk;
-	int ret;
+	int ret, i;
 
 	if (sai->slots)
 		slots = sai->slots;
@@ -507,8 +512,22 @@  static int fsl_sai_hw_params(struct snd_pcm_substream *substream,
 	 * PDM mode, channels are independent
 	 * each channels are on one dataline/FIFO.
 	 */
-	if (sai->is_pdm_mode)
+	if (sai->is_pdm_mode) {
 		pins = channels;
+		dl_type = FSL_SAI_DL_PDM;
+	}
+
+	for (i = 0; i < dl_cfg_cnt; i++) {
+		if (dl_cfg[i].type == dl_type && dl_cfg[i].pins[tx] == pins) {
+			dl_cfg_idx = i;
+			break;
+		}
+	}
+
+	if (hweight8(dl_cfg[dl_cfg_idx].mask[tx]) < pins) {
+		dev_err(cpu_dai->dev, "channel not supported\n");
+		return -EINVAL;
+	}
 
 	bclk = params_rate(params) * (sai->bclk_ratio ? sai->bclk_ratio : slots * slot_width);
 
@@ -571,13 +590,28 @@  static int fsl_sai_hw_params(struct snd_pcm_substream *substream,
 				   FSL_SAI_CR5_FBT_MASK, val_cr5);
 	}
 
-	if (sai->soc_data->pins > 1)
+	if (hweight8(dl_cfg[dl_cfg_idx].mask[tx]) <= 1)
+		regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs),
+				   FSL_SAI_CR4_FCOMB_MASK, 0);
+	else
 		regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs),
 				   FSL_SAI_CR4_FCOMB_MASK, FSL_SAI_CR4_FCOMB_SOFT);
 
+	dma_params = tx ? &sai->dma_params_tx : &sai->dma_params_rx;
+	dma_params->addr = sai->res->start + FSL_SAI_xDR0(tx) +
+			   dl_cfg[dl_cfg_idx].start_off[tx] * 0x4;
+
+	/* Find a proper tcre setting */
+	for (i = 0; i < sai->soc_data->pins; i++) {
+		trce_mask = (1 << (i + 1)) - 1;
+		if (hweight8(dl_cfg[dl_cfg_idx].mask[tx] & trce_mask) == pins)
+			break;
+	}
+
 	regmap_update_bits(sai->regmap, FSL_SAI_xCR3(tx, ofs),
 			   FSL_SAI_CR3_TRCE_MASK,
-			   FSL_SAI_CR3_TRCE((1 << pins) - 1));
+			   FSL_SAI_CR3_TRCE((dl_cfg[dl_cfg_idx].mask[tx] & trce_mask)));
+
 	regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs),
 			   FSL_SAI_CR4_SYWD_MASK | FSL_SAI_CR4_FRSZ_MASK |
 			   FSL_SAI_CR4_CHMOD_MASK,
@@ -1068,6 +1102,118 @@  static int fsl_sai_check_version(struct device *dev)
 	return 0;
 }
 
+/*
+ * Calculate the offset between first two datalines, don't
+ * different offset in one case.
+ */
+static unsigned int fsl_sai_calc_dl_off(unsigned long dl_mask)
+{
+	int fbidx, nbidx, offset;
+
+	fbidx = find_first_bit(&dl_mask, FSL_SAI_DL_NUM);
+	nbidx = find_next_bit(&dl_mask, FSL_SAI_DL_NUM, fbidx + 1);
+	offset = nbidx - fbidx - 1;
+
+	return (offset < 0 || offset >= (FSL_SAI_DL_NUM - 1) ? 0 : offset);
+}
+
+/*
+ * read the fsl,dataline property from dts file.
+ * It has 3 value for each configuration, first one means the type:
+ * I2S(1) or PDM(2), second one is dataline mask for 'rx', third one is
+ * dataline mask for 'tx'. for example
+ *
+ * fsl,dataline = <1 0xff 0xff 2 0xff 0x11>,
+ *
+ * It means I2S type rx mask is 0xff, tx mask is 0xff, PDM type
+ * rx mask is 0xff, tx mask is 0x11 (dataline 1 and 4 enabled).
+ *
+ */
+static int fsl_sai_read_dlcfg(struct fsl_sai *sai)
+{
+	struct platform_device *pdev = sai->pdev;
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	int ret, elems, i, index, num_cfg;
+	char *propname = "fsl,dataline";
+	struct fsl_sai_dl_cfg *cfg;
+	unsigned long dl_mask;
+	unsigned int soc_dl;
+	u32 rx, tx, type;
+
+	elems = of_property_count_u32_elems(np, propname);
+
+	if (elems <= 0) {
+		elems = 0;
+	} else if (elems % 3) {
+		dev_err(dev, "Number of elements must be divisible to 3.\n");
+		return -EINVAL;
+	}
+
+	num_cfg = elems / 3;
+	/*  Add one more for default value */
+	cfg = devm_kzalloc(&pdev->dev, (num_cfg + 1) * sizeof(*cfg), GFP_KERNEL);
+	if (!cfg)
+		return -ENOMEM;
+
+	/* Consider default value "0 0xFF 0xFF" if property is missing */
+	soc_dl = BIT(sai->soc_data->pins) - 1;
+	cfg[0].type = FSL_SAI_DL_DEFAULT;
+	cfg[0].pins[0] = sai->soc_data->pins;
+	cfg[0].mask[0] = soc_dl;
+	cfg[0].start_off[0] = 0;
+	cfg[0].next_off[0] = 0;
+
+	cfg[0].pins[1] = sai->soc_data->pins;
+	cfg[0].mask[1] = soc_dl;
+	cfg[0].start_off[1] = 0;
+	cfg[0].next_off[1] = 0;
+	for (i = 1, index = 0; i < num_cfg + 1; i++) {
+		/*
+		 * type of dataline
+		 * 0 means default mode
+		 * 1 means I2S mode
+		 * 2 means PDM mode
+		 */
+		ret = of_property_read_u32_index(np, propname, index++, &type);
+		if (ret)
+			return -EINVAL;
+
+		ret = of_property_read_u32_index(np, propname, index++, &rx);
+		if (ret)
+			return -EINVAL;
+
+		ret = of_property_read_u32_index(np, propname, index++, &tx);
+		if (ret)
+			return -EINVAL;
+
+		if ((rx & ~soc_dl) || (tx & ~soc_dl)) {
+			dev_err(dev, "dataline cfg[%d] setting error, mask is 0x%x\n", i, soc_dl);
+			return -EINVAL;
+		}
+
+		rx = rx & soc_dl;
+		tx = tx & soc_dl;
+
+		cfg[i].type = type;
+		cfg[i].pins[0] = hweight8(rx);
+		cfg[i].mask[0] = rx;
+		dl_mask = rx;
+		cfg[i].start_off[0] = find_first_bit(&dl_mask, FSL_SAI_DL_NUM);
+		cfg[i].next_off[0] = fsl_sai_calc_dl_off(rx);
+
+		cfg[i].pins[1] = hweight8(tx);
+		cfg[i].mask[1] = tx;
+		dl_mask = tx;
+		cfg[i].start_off[1] = find_first_bit(&dl_mask, FSL_SAI_DL_NUM);
+		cfg[i].next_off[1] = fsl_sai_calc_dl_off(tx);
+	}
+
+	sai->dl_cfg = cfg;
+	sai->dl_cfg_cnt = num_cfg + 1;
+	return 0;
+}
+
 static int fsl_sai_runtime_suspend(struct device *dev);
 static int fsl_sai_runtime_resume(struct device *dev);
 
@@ -1134,6 +1280,13 @@  static int fsl_sai_probe(struct platform_device *pdev)
 	else
 		sai->mclk_clk[0] = sai->bus_clk;
 
+	/* read dataline mask for rx and tx*/
+	ret = fsl_sai_read_dlcfg(sai);
+	if (ret < 0) {
+		dev_err(dev, "failed to read dlcfg %d\n", ret);
+		return ret;
+	}
+
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
 		return irq;
diff --git a/sound/soc/fsl/fsl_sai.h b/sound/soc/fsl/fsl_sai.h
index 4d657edc9c9f..9bb8ced520c8 100644
--- a/sound/soc/fsl/fsl_sai.h
+++ b/sound/soc/fsl/fsl_sai.h
@@ -218,6 +218,13 @@ 
 
 #define PMQOS_CPU_LATENCY   BIT(0)
 
+/* Max number of dataline */
+#define FSL_SAI_DL_NUM		(8)
+/* default dataline type is zero */
+#define FSL_SAI_DL_DEFAULT	(0)
+#define FSL_SAI_DL_I2S		BIT(0)
+#define FSL_SAI_DL_PDM		BIT(1)
+
 struct fsl_sai_soc_data {
 	bool use_imx_pcm;
 	bool use_edma;
@@ -253,6 +260,14 @@  struct fsl_sai_param {
 	u32 dataline;
 };
 
+struct fsl_sai_dl_cfg {
+	unsigned int type;
+	unsigned int pins[2];
+	unsigned int mask[2];
+	unsigned int start_off[2];
+	unsigned int next_off[2];
+};
+
 struct fsl_sai {
 	struct platform_device *pdev;
 	struct regmap *regmap;
@@ -265,6 +280,8 @@  struct fsl_sai {
 	bool is_dsp_mode;
 	bool is_pdm_mode;
 	bool synchronous[2];
+	struct fsl_sai_dl_cfg *dl_cfg;
+	unsigned int dl_cfg_cnt;
 
 	unsigned int mclk_id[2];
 	unsigned int mclk_streams;