| Message ID | 20190809133407.25918-2-srinivas.kandagatla@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ASoC: codecs: Add WSA881x Smart Speaker amplifier support | expand |
On 09-08-19, 14:34, Srinivas Kandagatla wrote: > This patch adds bindings for Soundwire Slave devices that includes how > SoundWire enumeration address and Link ID are used to represented in > SoundWire slave device tree nodes. Rob does this look good to you, I intent to apply the soundwire parts > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ > 1 file changed, 51 insertions(+) > create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt > > diff --git a/Documentation/devicetree/bindings/soundwire/slave.txt b/Documentation/devicetree/bindings/soundwire/slave.txt > new file mode 100644 > index 000000000000..201f65d2fafa > --- /dev/null > +++ b/Documentation/devicetree/bindings/soundwire/slave.txt > @@ -0,0 +1,51 @@ > +SoundWire slave device bindings. > + > +SoundWire is a 2-pin multi-drop interface with data and clock line. > +It facilitates development of low cost, efficient, high performance systems. > + > +SoundWire slave devices: > +Every SoundWire controller node can contain zero or more child nodes > +representing slave devices on the bus. Every SoundWire slave device is > +uniquely determined by the enumeration address containing 5 fields: > +SoundWire Version, Instance ID, Manufacturer ID, Part ID > +and Class ID for a device. Addition to below required properties, > +child nodes can have device specific bindings. > + > +Required properties: > +- compatible: "sdw<LinkID><VersionID><InstanceID><MFD><PID><CID>". > + Is the textual representation of SoundWire Enumeration > + address along with Link ID. compatible string should contain > + SoundWire Link ID, SoundWire Version ID, Instance ID, > + Manufacturer ID, Part ID and Class ID in order > + represented as above and shall be in lower-case hexadecimal > + with leading zeroes. Vaild sizes of these fields are > + LinkID is 1 nibble, > + Version ID is 1 nibble > + Instance ID in 1 nibble > + MFD in 4 nibbles > + PID in 4 nibbles > + CID is 2 nibbles > + > + Version number '0x1' represents SoundWire 1.0 > + Version number '0x2' represents SoundWire 1.1 > + ex: "sdw0110217201000" represents 0 LinkID, > + SoundWire 1.0 version slave with Instance ID 1. > + More Information on detail of encoding of these fields can be > + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. > + > +SoundWire example for Qualcomm's SoundWire controller: > + > +soundwire@c2d0000 { > + compatible = "qcom,soundwire-v1.5.0" > + reg = <0x0c2d0000 0x2000>; > + > + spkr_left:wsa8810-left{ > + compatible = "sdw0110217201000"; > + ... > + }; > + > + spkr_right:wsa8810-right{ > + compatible = "sdw0120217201000"; > + ... > + }; > +}; > -- > 2.21.0
On Fri, Aug 09, 2019 at 02:34:04PM +0100, Srinivas Kandagatla wrote: > This patch adds bindings for Soundwire Slave devices that includes how > SoundWire enumeration address and Link ID are used to represented in > SoundWire slave device tree nodes. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ > 1 file changed, 51 insertions(+) > create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt Can you convert this to DT schema given it is a common binding. What does the host controller look like? You need to define the node hierarchy. Bus controller schemas should then include the bus schema. See spi-controller.yaml. > > diff --git a/Documentation/devicetree/bindings/soundwire/slave.txt b/Documentation/devicetree/bindings/soundwire/slave.txt > new file mode 100644 > index 000000000000..201f65d2fafa > --- /dev/null > +++ b/Documentation/devicetree/bindings/soundwire/slave.txt > @@ -0,0 +1,51 @@ > +SoundWire slave device bindings. > + > +SoundWire is a 2-pin multi-drop interface with data and clock line. > +It facilitates development of low cost, efficient, high performance systems. > + > +SoundWire slave devices: > +Every SoundWire controller node can contain zero or more child nodes > +representing slave devices on the bus. Every SoundWire slave device is > +uniquely determined by the enumeration address containing 5 fields: > +SoundWire Version, Instance ID, Manufacturer ID, Part ID > +and Class ID for a device. Addition to below required properties, > +child nodes can have device specific bindings. > + > +Required properties: > +- compatible: "sdw<LinkID><VersionID><InstanceID><MFD><PID><CID>". > + Is the textual representation of SoundWire Enumeration > + address along with Link ID. compatible string should contain > + SoundWire Link ID, SoundWire Version ID, Instance ID, > + Manufacturer ID, Part ID and Class ID in order > + represented as above and shall be in lower-case hexadecimal > + with leading zeroes. Vaild sizes of these fields are > + LinkID is 1 nibble, > + Version ID is 1 nibble > + Instance ID in 1 nibble > + MFD in 4 nibbles > + PID in 4 nibbles > + CID is 2 nibbles > + > + Version number '0x1' represents SoundWire 1.0 > + Version number '0x2' represents SoundWire 1.1 This can all be a regex. > + ex: "sdw0110217201000" represents 0 LinkID, > + SoundWire 1.0 version slave with Instance ID 1. > + More Information on detail of encoding of these fields can be > + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. > + > +SoundWire example for Qualcomm's SoundWire controller: > + > +soundwire@c2d0000 { > + compatible = "qcom,soundwire-v1.5.0" > + reg = <0x0c2d0000 0x2000>; > + > + spkr_left:wsa8810-left{ > + compatible = "sdw0110217201000"; > + ... > + }; > + > + spkr_right:wsa8810-right{ > + compatible = "sdw0120217201000"; The normal way to distinguish instances is with 'reg'. So I think you need 'reg' with Instance ID moved there at least. Just guessing, but perhaps Link ID, too? And for 2 different classes of device is that enough? Rob
On 21/08/2019 22:44, Rob Herring wrote: > On Fri, Aug 09, 2019 at 02:34:04PM +0100, Srinivas Kandagatla wrote: >> This patch adds bindings for Soundwire Slave devices that includes how >> SoundWire enumeration address and Link ID are used to represented in >> SoundWire slave device tree nodes. >> >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> --- >> .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ >> 1 file changed, 51 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt > > Can you convert this to DT schema given it is a common binding. > I will give that a go in next version! > What does the host controller look like? You need to define the node > hierarchy. Bus controller schemas should then include the bus schema. > See spi-controller.yaml. Host controller is always parent of these devices which is represented in the example. In my previous patches, i did put this slave bindings in bus.txt, but Vinod suggested to move it to slave.txt. Are you suggesting to add two yamls here, one for slave and one for bus Or just document this in one bus bindings? > >> >> diff --git a/Documentation/devicetree/bindings/soundwire/slave.txt b/Documentation/devicetree/bindings/soundwire/slave.txt >> new file mode 100644 >> index 000000000000..201f65d2fafa >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/soundwire/slave.txt >> @@ -0,0 +1,51 @@ >> +SoundWire slave device bindings. >> + >> +SoundWire is a 2-pin multi-drop interface with data and clock line. >> +It facilitates development of low cost, efficient, high performance systems. >> + >> +SoundWire slave devices: >> +Every SoundWire controller node can contain zero or more child nodes >> +representing slave devices on the bus. Every SoundWire slave device is >> +uniquely determined by the enumeration address containing 5 fields: >> +SoundWire Version, Instance ID, Manufacturer ID, Part ID >> +and Class ID for a device. Addition to below required properties, >> +child nodes can have device specific bindings. >> + >> +Required properties: >> +- compatible: "sdw<LinkID><VersionID><InstanceID><MFD><PID><CID>". >> + Is the textual representation of SoundWire Enumeration >> + address along with Link ID. compatible string should contain >> + SoundWire Link ID, SoundWire Version ID, Instance ID, >> + Manufacturer ID, Part ID and Class ID in order >> + represented as above and shall be in lower-case hexadecimal >> + with leading zeroes. Vaild sizes of these fields are >> + LinkID is 1 nibble, >> + Version ID is 1 nibble >> + Instance ID in 1 nibble >> + MFD in 4 nibbles >> + PID in 4 nibbles >> + CID is 2 nibbles >> + >> + Version number '0x1' represents SoundWire 1.0 >> + Version number '0x2' represents SoundWire 1.1 > > This can all be a regex. > >> + ex: "sdw0110217201000" represents 0 LinkID, >> + SoundWire 1.0 version slave with Instance ID 1. >> + More Information on detail of encoding of these fields can be >> + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. >> + >> +SoundWire example for Qualcomm's SoundWire controller: >> + >> +soundwire@c2d0000 { >> + compatible = "qcom,soundwire-v1.5.0" >> + reg = <0x0c2d0000 0x2000>; >> + >> + spkr_left:wsa8810-left{ >> + compatible = "sdw0110217201000"; >> + ... >> + }; >> + >> + spkr_right:wsa8810-right{ >> + compatible = "sdw0120217201000"; > > The normal way to distinguish instances is with 'reg'. So I think you > need 'reg' with Instance ID moved there at least. Just guessing, but > perhaps Link ID, too? And for 2 different classes of device is that > enough? In previous bindings ( https://lists.gt.net/linux/kernel/3403276 ) we did have instance-id as different property, however Pierre had some good suggestion to make it align with _ADR encoding as per MIPI DisCo spec. Do you still think that we should split the instance id to reg property? Thanks, srini > > Rob >
On 22-08-19, 11:12, Srinivas Kandagatla wrote: > > > On 21/08/2019 22:44, Rob Herring wrote: > > On Fri, Aug 09, 2019 at 02:34:04PM +0100, Srinivas Kandagatla wrote: > > > This patch adds bindings for Soundwire Slave devices that includes how > > > SoundWire enumeration address and Link ID are used to represented in > > > SoundWire slave device tree nodes. > > > > > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > > --- > > > .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ > > > 1 file changed, 51 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt > > > > Can you convert this to DT schema given it is a common binding. > > > > I will give that a go in next version! > > > What does the host controller look like? You need to define the node > > hierarchy. Bus controller schemas should then include the bus schema. > > See spi-controller.yaml. > > Host controller is always parent of these devices which is represented in > the example. > > In my previous patches, i did put this slave bindings in bus.txt, but Vinod > suggested to move it to slave.txt. > > Are you suggesting to add two yamls here, one for slave and one for bus > Or just document this in one bus bindings? That would be fine by me :-)
On Thu, Aug 22, 2019 at 5:12 AM Srinivas Kandagatla <srinivas.kandagatla@linaro.org> wrote: > > > > On 21/08/2019 22:44, Rob Herring wrote: > > On Fri, Aug 09, 2019 at 02:34:04PM +0100, Srinivas Kandagatla wrote: > >> This patch adds bindings for Soundwire Slave devices that includes how > >> SoundWire enumeration address and Link ID are used to represented in > >> SoundWire slave device tree nodes. > >> > >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > >> --- > >> .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ > >> 1 file changed, 51 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt > > > > Can you convert this to DT schema given it is a common binding. > > > > I will give that a go in next version! > > > What does the host controller look like? You need to define the node > > hierarchy. Bus controller schemas should then include the bus schema. > > See spi-controller.yaml. > > Host controller is always parent of these devices which is represented > in the example. > > In my previous patches, i did put this slave bindings in bus.txt, but > Vinod suggested to move it to slave.txt. > > Are you suggesting to add two yamls here, one for slave and one for bus > Or just document this in one bus bindings? One. Like I said, see spi-controller.yaml. > >> diff --git a/Documentation/devicetree/bindings/soundwire/slave.txt b/Documentation/devicetree/bindings/soundwire/slave.txt > >> new file mode 100644 > >> index 000000000000..201f65d2fafa > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/soundwire/slave.txt > >> @@ -0,0 +1,51 @@ > >> +SoundWire slave device bindings. > >> + > >> +SoundWire is a 2-pin multi-drop interface with data and clock line. > >> +It facilitates development of low cost, efficient, high performance systems. > >> + > >> +SoundWire slave devices: > >> +Every SoundWire controller node can contain zero or more child nodes > >> +representing slave devices on the bus. Every SoundWire slave device is > >> +uniquely determined by the enumeration address containing 5 fields: > >> +SoundWire Version, Instance ID, Manufacturer ID, Part ID > >> +and Class ID for a device. Addition to below required properties, > >> +child nodes can have device specific bindings. > >> + > >> +Required properties: > >> +- compatible: "sdw<LinkID><VersionID><InstanceID><MFD><PID><CID>". > >> + Is the textual representation of SoundWire Enumeration > >> + address along with Link ID. compatible string should contain > >> + SoundWire Link ID, SoundWire Version ID, Instance ID, > >> + Manufacturer ID, Part ID and Class ID in order > >> + represented as above and shall be in lower-case hexadecimal > >> + with leading zeroes. Vaild sizes of these fields are > >> + LinkID is 1 nibble, > >> + Version ID is 1 nibble > >> + Instance ID in 1 nibble > >> + MFD in 4 nibbles > >> + PID in 4 nibbles > >> + CID is 2 nibbles > >> + > >> + Version number '0x1' represents SoundWire 1.0 > >> + Version number '0x2' represents SoundWire 1.1 > > > > This can all be a regex. > > > >> + ex: "sdw0110217201000" represents 0 LinkID, > >> + SoundWire 1.0 version slave with Instance ID 1. > >> + More Information on detail of encoding of these fields can be > >> + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. > >> + > >> +SoundWire example for Qualcomm's SoundWire controller: > >> + > >> +soundwire@c2d0000 { > >> + compatible = "qcom,soundwire-v1.5.0" > >> + reg = <0x0c2d0000 0x2000>; > >> + > >> + spkr_left:wsa8810-left{ > >> + compatible = "sdw0110217201000"; > >> + ... > >> + }; > >> + > >> + spkr_right:wsa8810-right{ > >> + compatible = "sdw0120217201000"; > > > > The normal way to distinguish instances is with 'reg'. So I think you > > need 'reg' with Instance ID moved there at least. Just guessing, but > > perhaps Link ID, too? And for 2 different classes of device is that > > enough? > > In previous bindings ( https://lists.gt.net/linux/kernel/3403276 ) we > did have instance-id as different property, however Pierre had some good > suggestion to make it align with _ADR encoding as per MIPI DisCo spec. > > Do you still think that we should split the instance id to reg property? Assuming you could have more than 1 of the same device on the bus, then you need some way to distinguish them and the way that's done for DT is unit-address/reg. And compatible strings should be constant for each instance. Rob
On 22-08-19, 07:36, Rob Herring wrote: > On Thu, Aug 22, 2019 at 5:12 AM Srinivas Kandagatla > <srinivas.kandagatla@linaro.org> wrote: > > > > > > > > On 21/08/2019 22:44, Rob Herring wrote: > > > On Fri, Aug 09, 2019 at 02:34:04PM +0100, Srinivas Kandagatla wrote: > > >> This patch adds bindings for Soundwire Slave devices that includes how > > >> SoundWire enumeration address and Link ID are used to represented in > > >> SoundWire slave device tree nodes. > > >> > > >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > >> --- > > >> .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ > > >> 1 file changed, 51 insertions(+) > > >> create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt > > > > > > Can you convert this to DT schema given it is a common binding. > > > > > > > I will give that a go in next version! > > > > > What does the host controller look like? You need to define the node > > > hierarchy. Bus controller schemas should then include the bus schema. > > > See spi-controller.yaml. > > > > Host controller is always parent of these devices which is represented > > in the example. > > > > In my previous patches, i did put this slave bindings in bus.txt, but > > Vinod suggested to move it to slave.txt. > > > > Are you suggesting to add two yamls here, one for slave and one for bus > > Or just document this in one bus bindings? > > One. Like I said, see spi-controller.yaml. > > > >> diff --git a/Documentation/devicetree/bindings/soundwire/slave.txt b/Documentation/devicetree/bindings/soundwire/slave.txt > > >> new file mode 100644 > > >> index 000000000000..201f65d2fafa > > >> --- /dev/null > > >> +++ b/Documentation/devicetree/bindings/soundwire/slave.txt > > >> @@ -0,0 +1,51 @@ > > >> +SoundWire slave device bindings. > > >> + > > >> +SoundWire is a 2-pin multi-drop interface with data and clock line. > > >> +It facilitates development of low cost, efficient, high performance systems. > > >> + > > >> +SoundWire slave devices: > > >> +Every SoundWire controller node can contain zero or more child nodes > > >> +representing slave devices on the bus. Every SoundWire slave device is > > >> +uniquely determined by the enumeration address containing 5 fields: > > >> +SoundWire Version, Instance ID, Manufacturer ID, Part ID > > >> +and Class ID for a device. Addition to below required properties, > > >> +child nodes can have device specific bindings. > > >> + > > >> +Required properties: > > >> +- compatible: "sdw<LinkID><VersionID><InstanceID><MFD><PID><CID>". > > >> + Is the textual representation of SoundWire Enumeration > > >> + address along with Link ID. compatible string should contain > > >> + SoundWire Link ID, SoundWire Version ID, Instance ID, > > >> + Manufacturer ID, Part ID and Class ID in order > > >> + represented as above and shall be in lower-case hexadecimal > > >> + with leading zeroes. Vaild sizes of these fields are > > >> + LinkID is 1 nibble, > > >> + Version ID is 1 nibble > > >> + Instance ID in 1 nibble > > >> + MFD in 4 nibbles > > >> + PID in 4 nibbles > > >> + CID is 2 nibbles > > >> + > > >> + Version number '0x1' represents SoundWire 1.0 > > >> + Version number '0x2' represents SoundWire 1.1 > > > > > > This can all be a regex. > > > > > >> + ex: "sdw0110217201000" represents 0 LinkID, > > >> + SoundWire 1.0 version slave with Instance ID 1. > > >> + More Information on detail of encoding of these fields can be > > >> + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. > > >> + > > >> +SoundWire example for Qualcomm's SoundWire controller: > > >> + > > >> +soundwire@c2d0000 { > > >> + compatible = "qcom,soundwire-v1.5.0" > > >> + reg = <0x0c2d0000 0x2000>; > > >> + > > >> + spkr_left:wsa8810-left{ > > >> + compatible = "sdw0110217201000"; > > >> + ... > > >> + }; > > >> + > > >> + spkr_right:wsa8810-right{ > > >> + compatible = "sdw0120217201000"; > > > > > > The normal way to distinguish instances is with 'reg'. So I think you > > > need 'reg' with Instance ID moved there at least. Just guessing, but > > > perhaps Link ID, too? And for 2 different classes of device is that > > > enough? > > > > In previous bindings ( https://lists.gt.net/linux/kernel/3403276 ) we > > did have instance-id as different property, however Pierre had some good > > suggestion to make it align with _ADR encoding as per MIPI DisCo spec. > > > > Do you still think that we should split the instance id to reg property? > > Assuming you could have more than 1 of the same device on the bus, > then you need some way to distinguish them and the way that's done for > DT is unit-address/reg. And compatible strings should be constant for > each instance. That does make sense, we can use unit-address/reg as instance id. Thanks
On 22/08/2019 13:36, Rob Herring wrote: >>>> +soundwire@c2d0000 { >>>> + compatible = "qcom,soundwire-v1.5.0" >>>> + reg = <0x0c2d0000 0x2000>; >>>> + >>>> + spkr_left:wsa8810-left{ >>>> + compatible = "sdw0110217201000"; >>>> + ... >>>> + }; >>>> + >>>> + spkr_right:wsa8810-right{ >>>> + compatible = "sdw0120217201000"; >>> The normal way to distinguish instances is with 'reg'. So I think you >>> need 'reg' with Instance ID moved there at least. Just guessing, but >>> perhaps Link ID, too? And for 2 different classes of device is that >>> enough? >> In previous bindings (https://lists.gt.net/linux/kernel/3403276 ) we >> did have instance-id as different property, however Pierre had some good >> suggestion to make it align with _ADR encoding as per MIPI DisCo spec. >> >> Do you still think that we should split the instance id to reg property? > Assuming you could have more than 1 of the same device on the bus, > then you need some way to distinguish them and the way that's done for > DT is unit-address/reg. And compatible strings should be constant for > each instance. That is a good point! Okay that makes more sense keep compatible string constant. Class ID would be constant for given functionality that the driver will provide. So we will end up with some thing like this: soundwire@c2d0000 { compatible = "qcom,soundwire-v1.5.0" reg = <0x0c2d0000 0x2000>; #address-cells = <1>; #size-cells = <0>; spkr_left:skpr@1{ compatible = "sdw10217201000"; reg = <0x1> sdw-link-id = <0>; ... }; spkr_right:spkr@2{ compatible = "sdw10217201000"; reg = <0x2> sdw-link-id = <0>; }; }; I will spin this in next version! Thanks, srini > > Rob
On Thu, Aug 22, 2019 at 7:56 AM Srinivas Kandagatla <srinivas.kandagatla@linaro.org> wrote: > > > > On 22/08/2019 13:36, Rob Herring wrote: > >>>> +soundwire@c2d0000 { > >>>> + compatible = "qcom,soundwire-v1.5.0" > >>>> + reg = <0x0c2d0000 0x2000>; > >>>> + > >>>> + spkr_left:wsa8810-left{ > >>>> + compatible = "sdw0110217201000"; > >>>> + ... > >>>> + }; > >>>> + > >>>> + spkr_right:wsa8810-right{ > >>>> + compatible = "sdw0120217201000"; > >>> The normal way to distinguish instances is with 'reg'. So I think you > >>> need 'reg' with Instance ID moved there at least. Just guessing, but > >>> perhaps Link ID, too? And for 2 different classes of device is that > >>> enough? > >> In previous bindings (https://lists.gt.net/linux/kernel/3403276 ) we > >> did have instance-id as different property, however Pierre had some good > >> suggestion to make it align with _ADR encoding as per MIPI DisCo spec. > >> > >> Do you still think that we should split the instance id to reg property? > > Assuming you could have more than 1 of the same device on the bus, > > then you need some way to distinguish them and the way that's done for > > DT is unit-address/reg. And compatible strings should be constant for > > each instance. > That is a good point! > Okay that makes more sense keep compatible string constant. > Class ID would be constant for given functionality that the driver will > provide. > > So we will end up with some thing like this: > > soundwire@c2d0000 { > compatible = "qcom,soundwire-v1.5.0" > reg = <0x0c2d0000 0x2000>; > #address-cells = <1>; > #size-cells = <0>; > > spkr_left:skpr@1{ > compatible = "sdw10217201000"; > reg = <0x1> > sdw-link-id = <0>; Not really sure what Link ID is, but maybe it should be part of reg too if it is part of how you address a device. > ... > }; > > spkr_right:spkr@2{ > compatible = "sdw10217201000"; > reg = <0x2> > sdw-link-id = <0>; > }; > }; > > I will spin this in next version! > > Thanks, > srini > > > > > Rob
diff --git a/Documentation/devicetree/bindings/soundwire/slave.txt b/Documentation/devicetree/bindings/soundwire/slave.txt new file mode 100644 index 000000000000..201f65d2fafa --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/slave.txt @@ -0,0 +1,51 @@ +SoundWire slave device bindings. + +SoundWire is a 2-pin multi-drop interface with data and clock line. +It facilitates development of low cost, efficient, high performance systems. + +SoundWire slave devices: +Every SoundWire controller node can contain zero or more child nodes +representing slave devices on the bus. Every SoundWire slave device is +uniquely determined by the enumeration address containing 5 fields: +SoundWire Version, Instance ID, Manufacturer ID, Part ID +and Class ID for a device. Addition to below required properties, +child nodes can have device specific bindings. + +Required properties: +- compatible: "sdw<LinkID><VersionID><InstanceID><MFD><PID><CID>". + Is the textual representation of SoundWire Enumeration + address along with Link ID. compatible string should contain + SoundWire Link ID, SoundWire Version ID, Instance ID, + Manufacturer ID, Part ID and Class ID in order + represented as above and shall be in lower-case hexadecimal + with leading zeroes. Vaild sizes of these fields are + LinkID is 1 nibble, + Version ID is 1 nibble + Instance ID in 1 nibble + MFD in 4 nibbles + PID in 4 nibbles + CID is 2 nibbles + + Version number '0x1' represents SoundWire 1.0 + Version number '0x2' represents SoundWire 1.1 + ex: "sdw0110217201000" represents 0 LinkID, + SoundWire 1.0 version slave with Instance ID 1. + More Information on detail of encoding of these fields can be + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. + +SoundWire example for Qualcomm's SoundWire controller: + +soundwire@c2d0000 { + compatible = "qcom,soundwire-v1.5.0" + reg = <0x0c2d0000 0x2000>; + + spkr_left:wsa8810-left{ + compatible = "sdw0110217201000"; + ... + }; + + spkr_right:wsa8810-right{ + compatible = "sdw0120217201000"; + ... + }; +};
This patch adds bindings for Soundwire Slave devices that includes how SoundWire enumeration address and Link ID are used to represented in SoundWire slave device tree nodes. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- .../devicetree/bindings/soundwire/slave.txt | 51 +++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 Documentation/devicetree/bindings/soundwire/slave.txt