diff --git a/sound/soc/sh/Kconfig b/sound/soc/sh/Kconfig
index a931c96..e39d78b 100644
--- a/sound/soc/sh/Kconfig
+++ b/sound/soc/sh/Kconfig
@@ -17,9 +17,6 @@ config SND_SOC_SH4_HAC
 	select AC97_BUS
 	select SND_SOC_AC97_BUS
 
-config SND_SOC_SH4_SSI
-	tristate
-
 config SND_SOC_SH4_FSI
 	tristate "SH4 FSI support"
 	select SND_SIMPLE_CARD
diff --git a/sound/soc/sh/Makefile b/sound/soc/sh/Makefile
index 20f50ea..6c61f1d 100644
--- a/sound/soc/sh/Makefile
+++ b/sound/soc/sh/Makefile
@@ -4,11 +4,9 @@ obj-$(CONFIG_SND_SOC_PCM_SH7760)	+= snd-soc-dma-sh7760.o
 
 ## audio units found on some SH-4
 snd-soc-hac-objs	:= hac.o
-snd-soc-ssi-objs	:= ssi.o
 snd-soc-fsi-objs	:= fsi.o
 snd-soc-siu-objs	:= siu_pcm.o siu_dai.o
 obj-$(CONFIG_SND_SOC_SH4_HAC)	+= snd-soc-hac.o
-obj-$(CONFIG_SND_SOC_SH4_SSI)	+= snd-soc-ssi.o
 obj-$(CONFIG_SND_SOC_SH4_FSI)	+= snd-soc-fsi.o
 obj-$(CONFIG_SND_SOC_SH4_SIU)	+= snd-soc-siu.o
 
diff --git a/sound/soc/sh/ssi.c b/sound/soc/sh/ssi.c
deleted file mode 100644
index ab13146..0000000
--- a/sound/soc/sh/ssi.c
+++ /dev/null
@@ -1,411 +0,0 @@
-/*
- * Serial Sound Interface (I2S) support for SH7760/SH7780
- *
- * Copyright (c) 2007 Manuel Lauss <mano@roarinelk.homelinux.net>
- *
- *  licensed under the terms outlined in the file COPYING at the root
- *  of the linux kernel sources.
- *
- * dont forget to set IPSEL/OMSEL register bits (in your board code) to
- * enable SSI output pins!
- */
-
-/*
- * LIMITATIONS:
- *	The SSI unit has only one physical data line, so full duplex is
- *	impossible.  This can be remedied  on the  SH7760 by  using the
- *	other SSI unit for recording; however the SH7780 has only 1 SSI
- *	unit, and its pins are shared with the AC97 unit,  among others.
- *
- * FEATURES:
- *	The SSI features "compressed mode": in this mode it continuously
- *	streams PCM data over the I2S lines and uses LRCK as a handshake
- *	signal.  Can be used to send compressed data (AC3/DTS) to a DSP.
- *	The number of bits sent over the wire in a frame can be adjusted
- *	and can be independent from the actual sample bit depth. This is
- *	useful to support TDM mode codecs like the AD1939 which have a
- *	fixed TDM slot size, regardless of sample resolution.
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <sound/core.h>
-#include <sound/pcm.h>
-#include <sound/initval.h>
-#include <sound/soc.h>
-#include <asm/io.h>
-
-#define SSICR	0x00
-#define SSISR	0x04
-
-#define CR_DMAEN	(1 << 28)
-#define CR_CHNL_SHIFT	22
-#define CR_CHNL_MASK	(3 << CR_CHNL_SHIFT)
-#define CR_DWL_SHIFT	19
-#define CR_DWL_MASK	(7 << CR_DWL_SHIFT)
-#define CR_SWL_SHIFT	16
-#define CR_SWL_MASK	(7 << CR_SWL_SHIFT)
-#define CR_SCK_MASTER	(1 << 15)	/* bitclock master bit */
-#define CR_SWS_MASTER	(1 << 14)	/* wordselect master bit */
-#define CR_SCKP		(1 << 13)	/* I2Sclock polarity */
-#define CR_SWSP		(1 << 12)	/* LRCK polarity */
-#define CR_SPDP		(1 << 11)
-#define CR_SDTA		(1 << 10)	/* i2s alignment (msb/lsb) */
-#define CR_PDTA		(1 << 9)	/* fifo data alignment */
-#define CR_DEL		(1 << 8)	/* delay data by 1 i2sclk */
-#define CR_BREN		(1 << 7)	/* clock gating in burst mode */
-#define CR_CKDIV_SHIFT	4
-#define CR_CKDIV_MASK	(7 << CR_CKDIV_SHIFT)	/* bitclock divider */
-#define CR_MUTE		(1 << 3)	/* SSI mute */
-#define CR_CPEN		(1 << 2)	/* compressed mode */
-#define CR_TRMD		(1 << 1)	/* transmit/receive select */
-#define CR_EN		(1 << 0)	/* enable SSI */
-
-#define SSIREG(reg)	(*(unsigned long *)(ssi->mmio + (reg)))
-
-struct ssi_priv {
-	unsigned long mmio;
-	unsigned long sysclk;
-	int inuse;
-} ssi_cpu_data[] = {
-#if defined(CONFIG_CPU_SUBTYPE_SH7760)
-	{
-		.mmio	= 0xFE680000,
-	},
-	{
-		.mmio	= 0xFE690000,
-	},
-#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
-	{
-		.mmio	= 0xFFE70000,
-	},
-#else
-#error "Unsupported SuperH SoC"
-#endif
-};
-
-/*
- * track usage of the SSI; it is simplex-only so prevent attempts of
- * concurrent playback + capture. FIXME: any locking required?
- */
-static int ssi_startup(struct snd_pcm_substream *substream,
-		       struct snd_soc_dai *dai)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
-	if (ssi->inuse) {
-		pr_debug("ssi: already in use!\n");
-		return -EBUSY;
-	} else
-		ssi->inuse = 1;
-	return 0;
-}
-
-static void ssi_shutdown(struct snd_pcm_substream *substream,
-			 struct snd_soc_dai *dai)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
-
-	ssi->inuse = 0;
-}
-
-static int ssi_trigger(struct snd_pcm_substream *substream, int cmd,
-		       struct snd_soc_dai *dai)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
-
-	switch (cmd) {
-	case SNDRV_PCM_TRIGGER_START:
-		SSIREG(SSICR) |= CR_DMAEN | CR_EN;
-		break;
-	case SNDRV_PCM_TRIGGER_STOP:
-		SSIREG(SSICR) &= ~(CR_DMAEN | CR_EN);
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
-static int ssi_hw_params(struct snd_pcm_substream *substream,
-			 struct snd_pcm_hw_params *params,
-			 struct snd_soc_dai *dai)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
-	unsigned long ssicr = SSIREG(SSICR);
-	unsigned int bits, channels, swl, recv, i;
-
-	channels = params_channels(params);
-	bits = params->msbits;
-	recv = (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ? 0 : 1;
-
-	pr_debug("ssi_hw_params() enter\nssicr was    %08lx\n", ssicr);
-	pr_debug("bits: %u channels: %u\n", bits, channels);
-
-	ssicr &= ~(CR_TRMD | CR_CHNL_MASK | CR_DWL_MASK | CR_PDTA |
-		   CR_SWL_MASK);
-
-	/* direction (send/receive) */
-	if (!recv)
-		ssicr |= CR_TRMD;	/* transmit */
-
-	/* channels */
-	if ((channels < 2) || (channels > 8) || (channels & 1)) {
-		pr_debug("ssi: invalid number of channels\n");
-		return -EINVAL;
-	}
-	ssicr |= ((channels >> 1) - 1) << CR_CHNL_SHIFT;
-
-	/* DATA WORD LENGTH (DWL): databits in audio sample */
-	i = 0;
-	switch (bits) {
-	case 32: ++i;
-	case 24: ++i;
-	case 22: ++i;
-	case 20: ++i;
-	case 18: ++i;
-	case 16: ++i;
-		 ssicr |= i << CR_DWL_SHIFT;
-	case 8:	 break;
-	default:
-		pr_debug("ssi: invalid sample width\n");
-		return -EINVAL;
-	}
-
-	/*
-	 * SYSTEM WORD LENGTH: size in bits of half a frame over the I2S
-	 * wires. This is usually bits_per_sample x channels/2;  i.e. in
-	 * Stereo mode  the SWL equals DWL.  SWL can  be bigger than the
-	 * product of (channels_per_slot x samplebits), e.g.  for codecs
-	 * like the AD1939 which  only accept 32bit wide TDM slots.  For
-	 * "standard" I2S operation we set SWL = chans / 2 * DWL here.
-	 * Waiting for ASoC to get TDM support ;-)
-	 */
-	if ((bits > 16) && (bits <= 24)) {
-		bits = 24;	/* these are padded by the SSI */
-		/*ssicr |= CR_PDTA;*/ /* cpu/data endianness ? */
-	}
-	i = 0;
-	swl = (bits * channels) / 2;
-	switch (swl) {
-	case 256: ++i;
-	case 128: ++i;
-	case 64:  ++i;
-	case 48:  ++i;
-	case 32:  ++i;
-	case 16:  ++i;
-		  ssicr |= i << CR_SWL_SHIFT;
-	case 8:   break;
-	default:
-		pr_debug("ssi: invalid system word length computed\n");
-		return -EINVAL;
-	}
-
-	SSIREG(SSICR) = ssicr;
-
-	pr_debug("ssi_hw_params() leave\nssicr is now %08lx\n", ssicr);
-	return 0;
-}
-
-static int ssi_set_sysclk(struct snd_soc_dai *cpu_dai, int clk_id,
-			  unsigned int freq, int dir)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[cpu_dai->id];
-
-	ssi->sysclk = freq;
-
-	return 0;
-}
-
-/*
- * This divider is used to generate the SSI_SCK (I2S bitclock) from the
- * clock at the HAC_BIT_CLK ("oversampling clock") pin.
- */
-static int ssi_set_clkdiv(struct snd_soc_dai *dai, int did, int div)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
-	unsigned long ssicr;
-	int i;
-
-	i = 0;
-	ssicr = SSIREG(SSICR) & ~CR_CKDIV_MASK;
-	switch (div) {
-	case 16: ++i;
-	case 8:  ++i;
-	case 4:  ++i;
-	case 2:  ++i;
-		 SSIREG(SSICR) = ssicr | (i << CR_CKDIV_SHIFT);
-	case 1:  break;
-	default:
-		pr_debug("ssi: invalid sck divider %d\n", div);
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
-static int ssi_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
-{
-	struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
-	unsigned long ssicr = SSIREG(SSICR);
-
-	pr_debug("ssi_set_fmt()\nssicr was    0x%08lx\n", ssicr);
-
-	ssicr &= ~(CR_DEL | CR_PDTA | CR_BREN | CR_SWSP | CR_SCKP |
-		   CR_SWS_MASTER | CR_SCK_MASTER);
-
-	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
-	case SND_SOC_DAIFMT_I2S:
-		break;
-	case SND_SOC_DAIFMT_RIGHT_J:
-		ssicr |= CR_DEL | CR_PDTA;
-		break;
-	case SND_SOC_DAIFMT_LEFT_J:
-		ssicr |= CR_DEL;
-		break;
-	default:
-		pr_debug("ssi: unsupported format\n");
-		return -EINVAL;
-	}
-
-	switch (fmt & SND_SOC_DAIFMT_CLOCK_MASK) {
-	case SND_SOC_DAIFMT_CONT:
-		break;
-	case SND_SOC_DAIFMT_GATED:
-		ssicr |= CR_BREN;
-		break;
-	}
-
-	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
-	case SND_SOC_DAIFMT_NB_NF:
-		ssicr |= CR_SCKP;	/* sample data at low clkedge */
-		break;
-	case SND_SOC_DAIFMT_NB_IF:
-		ssicr |= CR_SCKP | CR_SWSP;
-		break;
-	case SND_SOC_DAIFMT_IB_NF:
-		break;
-	case SND_SOC_DAIFMT_IB_IF:
-		ssicr |= CR_SWSP;	/* word select starts low */
-		break;
-	default:
-		pr_debug("ssi: invalid inversion\n");
-		return -EINVAL;
-	}
-
-	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
-	case SND_SOC_DAIFMT_CBM_CFM:
-		break;
-	case SND_SOC_DAIFMT_CBS_CFM:
-		ssicr |= CR_SCK_MASTER;
-		break;
-	case SND_SOC_DAIFMT_CBM_CFS:
-		ssicr |= CR_SWS_MASTER;
-		break;
-	case SND_SOC_DAIFMT_CBS_CFS:
-		ssicr |= CR_SWS_MASTER | CR_SCK_MASTER;
-		break;
-	default:
-		pr_debug("ssi: invalid master/slave configuration\n");
-		return -EINVAL;
-	}
-
-	SSIREG(SSICR) = ssicr;
-	pr_debug("ssi_set_fmt() leave\nssicr is now 0x%08lx\n", ssicr);
-
-	return 0;
-}
-
-/* the SSI depends on an external clocksource (at HAC_BIT_CLK) even in
- * Master mode,  so really this is board specific;  the SSI can do any
- * rate with the right bitclk and divider settings.
- */
-#define SSI_RATES	\
-	SNDRV_PCM_RATE_8000_192000
-
-/* the SSI can do 8-32 bit samples, with 8 possible channels */
-#define SSI_FMTS	\
-	(SNDRV_PCM_FMTBIT_S8      | SNDRV_PCM_FMTBIT_U8      |	\
-	 SNDRV_PCM_FMTBIT_S16_LE  | SNDRV_PCM_FMTBIT_U16_LE  |	\
-	 SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_U20_3LE |	\
-	 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_U24_3LE |	\
-	 SNDRV_PCM_FMTBIT_S32_LE  | SNDRV_PCM_FMTBIT_U32_LE)
-
-static const struct snd_soc_dai_ops ssi_dai_ops = {
-	.startup	= ssi_startup,
-	.shutdown	= ssi_shutdown,
-	.trigger	= ssi_trigger,
-	.hw_params	= ssi_hw_params,
-	.set_sysclk	= ssi_set_sysclk,
-	.set_clkdiv	= ssi_set_clkdiv,
-	.set_fmt	= ssi_set_fmt,
-};
-
-static struct snd_soc_dai_driver sh4_ssi_dai[] = {
-{
-	.name			= "ssi-dai.0",
-	.playback = {
-		.rates		= SSI_RATES,
-		.formats	= SSI_FMTS,
-		.channels_min	= 2,
-		.channels_max	= 8,
-	},
-	.capture = {
-		.rates		= SSI_RATES,
-		.formats	= SSI_FMTS,
-		.channels_min	= 2,
-		.channels_max	= 8,
-	},
-	.ops = &ssi_dai_ops,
-},
-#ifdef CONFIG_CPU_SUBTYPE_SH7760
-{
-	.name			= "ssi-dai.1",
-	.playback = {
-		.rates		= SSI_RATES,
-		.formats	= SSI_FMTS,
-		.channels_min	= 2,
-		.channels_max	= 8,
-	},
-	.capture = {
-		.rates		= SSI_RATES,
-		.formats	= SSI_FMTS,
-		.channels_min	= 2,
-		.channels_max	= 8,
-	},
-	.ops = &ssi_dai_ops,
-},
-#endif
-};
-
-static const struct snd_soc_component_driver sh4_ssi_component = {
-	.name		= "sh4-ssi",
-};
-
-static int sh4_soc_dai_probe(struct platform_device *pdev)
-{
-	return snd_soc_register_component(&pdev->dev, &sh4_ssi_component,
-					  sh4_ssi_dai, ARRAY_SIZE(sh4_ssi_dai));
-}
-
-static int sh4_soc_dai_remove(struct platform_device *pdev)
-{
-	snd_soc_unregister_component(&pdev->dev);
-	return 0;
-}
-
-static struct platform_driver sh4_ssi_driver = {
-	.driver = {
-			.name = "sh4-ssi-dai",
-	},
-
-	.probe = sh4_soc_dai_probe,
-	.remove = sh4_soc_dai_remove,
-};
-
-module_platform_driver(sh4_ssi_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("SuperH onchip SSI (I2S) audio driver");
-MODULE_AUTHOR("Manuel Lauss <mano@roarinelk.homelinux.net>");
