@@ -2297,6 +2297,52 @@ static ssize_t ath10k_tpc_stats_final_read(struct file *file,
.llseek = default_llseek,
};
+static ssize_t ath10k_write_warm_hw_reset(struct file *file,
+ const char __user *user_buf,
+ size_t count, loff_t *ppos)
+{
+ struct ath10k *ar = file->private_data;
+ int ret;
+ bool val;
+
+ if (kstrtobool_from_user(user_buf, count, &val))
+ return -EFAULT;
+
+ if (!val)
+ return -EINVAL;
+
+ mutex_lock(&ar->conf_mutex);
+
+ if (ar->state != ATH10K_STATE_ON) {
+ ret = -ENETDOWN;
+ goto exit;
+ }
+
+ if (!(test_bit(WMI_SERVICE_RESET_CHIP, ar->wmi.svc_map)))
+ ath10k_warn(ar, "wmi service for reset chip is not available\n");
+
+ ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->pdev_reset,
+ WMI_RST_MODE_WARM_RESET);
+
+ if (ret) {
+ ath10k_warn(ar, "failed to enable warm hw reset: %d\n", ret);
+ goto exit;
+ }
+
+ ret = count;
+
+exit:
+ mutex_unlock(&ar->conf_mutex);
+ return ret;
+}
+
+static const struct file_operations fops_warm_hw_reset = {
+ .write = ath10k_write_warm_hw_reset,
+ .open = simple_open,
+ .owner = THIS_MODULE,
+ .llseek = default_llseek,
+};
+
int ath10k_debug_create(struct ath10k *ar)
{
ar->debug.cal_data = vzalloc(ATH10K_DEBUG_CAL_DATA_LEN);
@@ -2425,6 +2471,9 @@ int ath10k_debug_register(struct ath10k *ar)
ar->debug.debugfs_phy, ar,
&fops_tpc_stats_final);
+ debugfs_create_file("warm_hw_reset", 0600, ar->debug.debugfs_phy, ar,
+ &fops_warm_hw_reset);
+
return 0;
}
@@ -1333,7 +1333,7 @@
.enable_per_tid_ampdu = WMI_PDEV_PARAM_UNSUPPORTED,
.cca_threshold = WMI_PDEV_PARAM_UNSUPPORTED,
.rts_fixed_rate = WMI_PDEV_PARAM_UNSUPPORTED,
- .pdev_reset = WMI_PDEV_PARAM_UNSUPPORTED,
+ .pdev_reset = WMI_10X_PDEV_PARAM_PDEV_RESET,
.wapi_mbssid_offset = WMI_PDEV_PARAM_UNSUPPORTED,
.arp_srcaddr = WMI_PDEV_PARAM_UNSUPPORTED,
.arp_dstaddr = WMI_PDEV_PARAM_UNSUPPORTED,
@@ -462,6 +462,7 @@ static inline char *wmi_service_name(int service_id)
SVCSTR(WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS);
SVCSTR(WMI_SERVICE_HOST_DFS_CHECK_SUPPORT);
SVCSTR(WMI_SERVICE_TPC_STATS_FINAL);
+ SVCSTR(WMI_SERVICE_RESET_CHIP);
default:
return NULL;
}
@@ -3934,7 +3935,11 @@ enum wmi_10x_pdev_param {
WMI_10X_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER,
WMI_10X_PDEV_PARAM_PEER_STA_PS_STATECHG_ENABLE,
WMI_10X_PDEV_PARAM_RTS_FIXED_RATE,
- WMI_10X_PDEV_PARAM_CAL_PERIOD
+ WMI_10X_PDEV_PARAM_CAL_PERIOD,
+ WMI_10X_PDEV_PARAM_ATF_STRICT_SCH,
+ WMI_10X_PDEV_PARAM_ATF_SCHED_DURATION,
+ WMI_10X_PDEV_PARAM_SET_PROMISC_MODE_CMDID,
+ WMI_10X_PDEV_PARAM_PDEV_RESET
};
enum wmi_10_4_pdev_param {
@@ -6501,6 +6506,15 @@ struct wmi_force_fw_hang_cmd {
__le32 delay_ms;
} __packed;
+enum wmi_pdev_reset_mode_type {
+ WMI_RST_MODE_TX_FLUSH = 1,
+ WMI_RST_MODE_WARM_RESET,
+ WMI_RST_MODE_COLD_RESET,
+ WMI_RST_MODE_WARM_RESET_RESTORE_CAL,
+ WMI_RST_MODE_COLD_RESET_RESTORE_CAL,
+ WMI_RST_MODE_MAX,
+};
+
enum ath10k_dbglog_level {
ATH10K_DBGLOG_LEVEL_VERBOSE = 0,
ATH10K_DBGLOG_LEVEL_INFO = 1,
Debugfs support to do hardware warm reset with WMI command WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi service is enabled in the firmware for backward compatibility). This change is purely for debugging purpose when hardware hangs/mutes. This hardware reset won't affect the connectivity but there will be small pause in data traffic. Here we are doing BB/MAC level reset and hence whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset. So the target will be in the active state. Below command used to warm reset the hardware. echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset Tested in QCA988X with firmware ver 10.2.4.70.45 Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011 Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> --- drivers/net/wireless/ath/ath10k/debug.c | 49 +++++++++++++++++++++++++++++++++ drivers/net/wireless/ath/ath10k/wmi.c | 2 +- drivers/net/wireless/ath/ath10k/wmi.h | 16 ++++++++++- 3 files changed, 65 insertions(+), 2 deletions(-)