@@ -2119,6 +2119,40 @@ static int ath10k_download_cal_data(struct ath10k *ar)
return 0;
}
+static void ath10k_core_fetch_btcoex_dt(struct ath10k *ar)
+{
+ struct device_node *node;
+ u8 coex_support = 0;
+ int ret;
+
+ node = ar->dev->of_node;
+ if (!node)
+ goto out;
+
+ ret = of_property_read_u8(node, "qcom,coexist-support", &coex_support);
+ if (ret) {
+ ar->coex_support = true;
+ goto out;
+ }
+
+ if (coex_support) {
+ ar->coex_support = true;
+ } else {
+ ar->coex_support = false;
+ ar->coex_gpio_pin = -1;
+ goto out;
+ }
+
+ ret = of_property_read_u32(node, "qcom,coexist-gpio-pin",
+ &ar->coex_gpio_pin);
+ if (ret)
+ ar->coex_gpio_pin = -1;
+
+out:
+ ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot coex_support %d coex_gpio_pin %d\n",
+ ar->coex_support, ar->coex_gpio_pin);
+}
+
static int ath10k_init_uart(struct ath10k *ar)
{
int ret;
@@ -2696,14 +2730,22 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
if (test_bit(WMI_SERVICE_BSS_CHANNEL_INFO_64, ar->wmi.svc_map))
val |= WMI_10_4_BSS_CHANNEL_INFO_64;
+ ath10k_core_fetch_btcoex_dt(ar);
+
/* 10.4 firmware supports BT-Coex without reloading firmware
* via pdev param. To support Bluetooth coexistence pdev param,
* WMI_COEX_GPIO_SUPPORT of extended resource config should be
* enabled always.
+ *
+ * We can still enable BTCOEX if firmware has the support
+ * eventhough btceox_support value is
+ * ATH10K_DT_BTCOEX_NOT_FOUND
*/
+
if (test_bit(WMI_SERVICE_COEX_GPIO, ar->wmi.svc_map) &&
test_bit(ATH10K_FW_FEATURE_BTCOEX_PARAM,
- ar->running_fw->fw_file.fw_features))
+ ar->running_fw->fw_file.fw_features) &&
+ ar->coex_support)
val |= WMI_10_4_COEX_GPIO_SUPPORT;
if (test_bit(WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
@@ -1222,6 +1222,9 @@ struct ath10k {
struct ath10k_bus_params bus_param;
struct completion peer_delete_done;
+ bool coex_support;
+ int coex_gpio_pin;
+
/* must be last */
u8 drv_priv[0] __aligned(sizeof(void *));
};
@@ -1978,6 +1978,9 @@ static ssize_t ath10k_write_btcoex(struct file *file,
if (strtobool(buf, &val) != 0)
return -EINVAL;
+ if (!ar->coex_support)
+ return -EOPNOTSUPP;
+
mutex_lock(&ar->conf_mutex);
if (ar->state != ATH10K_STATE_ON &&
@@ -4982,7 +4982,8 @@ static int ath10k_start(struct ieee80211_hw *hw)
param = ar->wmi.pdev_param->enable_btcoex;
if (test_bit(WMI_SERVICE_COEX_GPIO, ar->wmi.svc_map) &&
test_bit(ATH10K_FW_FEATURE_BTCOEX_PARAM,
- ar->running_fw->fw_file.fw_features)) {
+ ar->running_fw->fw_file.fw_features) &&
+ ar->coex_support) {
ret = ath10k_wmi_pdev_set_param(ar, param, 0);
if (ret) {
ath10k_warn(ar,
@@ -8787,7 +8787,7 @@ static int ath10k_wmi_10_4_op_get_vdev_subtype(struct ath10k *ar,
cmd = (struct wmi_ext_resource_config_10_4_cmd *)skb->data;
cmd->host_platform_config = __cpu_to_le32(type);
cmd->fw_feature_bitmap = __cpu_to_le32(fw_feature_bitmap);
- cmd->wlan_gpio_priority = __cpu_to_le32(-1);
+ cmd->wlan_gpio_priority = __cpu_to_le32(ar->coex_gpio_pin);
cmd->coex_version = __cpu_to_le32(WMI_NO_COEX_VERSION_SUPPORT);
cmd->coex_gpio_pin1 = __cpu_to_le32(-1);
cmd->coex_gpio_pin2 = __cpu_to_le32(-1);
BTCOEX feature is not supported by all QCA4019 chipsets. Since btcoex enabled by default in firmware, host needs to enable COEX support depends on the hardware. Enabling it by default in unsupported hardware will cause some feature disabled in hardware. This patch will read btcoex_support flag and wlan priority gpio pin number from DT. Depends on the btcoex_support flag value host will expose BTCOEX support and wlan priority gpio pin number to target. Testing: * Tested HW : QCA4019 * Tested FW : 10.4-3.2.1.1-00017 Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org> --- v2: * Changed coex_support to bool type drivers/net/wireless/ath/ath10k/core.c | 44 ++++++++++++++++++++++++++++++++- drivers/net/wireless/ath/ath10k/core.h | 3 +++ drivers/net/wireless/ath/ath10k/debug.c | 3 +++ drivers/net/wireless/ath/ath10k/mac.c | 3 ++- drivers/net/wireless/ath/ath10k/wmi.c | 2 +- 5 files changed, 52 insertions(+), 3 deletions(-)