@@ -1280,10 +1280,17 @@ static void ath10k_ce_per_engine_handler_adjust(struct ath10k_ce_pipe *ce_state)
int ath10k_ce_disable_interrupts(struct ath10k *ar)
{
+ struct ath10k_ce *ce = ath10k_ce_priv(ar);
+ struct ath10k_ce_pipe *ce_state;
+ u32 ctrl_addr;
int ce_id;
for (ce_id = 0; ce_id < CE_COUNT; ce_id++) {
- u32 ctrl_addr = ath10k_ce_base_address(ar, ce_id);
+ ce_state = &ce->ce_states[ce_id];
+ if (ce_state->attr_flags & CE_ATTR_POLL)
+ continue;
+
+ ctrl_addr = ath10k_ce_base_address(ar, ce_id);
ath10k_ce_copy_complete_intr_disable(ar, ctrl_addr);
ath10k_ce_error_intr_disable(ar, ctrl_addr);
@@ -1300,11 +1307,14 @@ void ath10k_ce_enable_interrupts(struct ath10k *ar)
int ce_id;
struct ath10k_ce_pipe *ce_state;
- /* Skip the last copy engine, CE7 the diagnostic window, as that
- * uses polling and isn't initialized for interrupts.
+ /* Enable interrupts for copy engine that
+ * are not using polling mode.
*/
- for (ce_id = 0; ce_id < CE_COUNT - 1; ce_id++) {
+ for (ce_id = 0; ce_id < CE_COUNT; ce_id++) {
ce_state = &ce->ce_states[ce_id];
+ if (ce_state->attr_flags & CE_ATTR_POLL)
+ continue;
+
ath10k_ce_per_engine_handler_adjust(ce_state);
}
}
@@ -275,16 +275,19 @@ void ath10k_ce_free_rri(struct ath10k *ar);
/* ce_attr.flags values */
/* Use NonSnooping PCIe accesses? */
-#define CE_ATTR_NO_SNOOP 1
+#define CE_ATTR_NO_SNOOP BIT(0)
/* Byte swap data words */
-#define CE_ATTR_BYTE_SWAP_DATA 2
+#define CE_ATTR_BYTE_SWAP_DATA BIT(1)
/* Swizzle descriptors? */
-#define CE_ATTR_SWIZZLE_DESCRIPTORS 4
+#define CE_ATTR_SWIZZLE_DESCRIPTORS BIT(2)
/* no interrupt on copy completion */
-#define CE_ATTR_DIS_INTR 8
+#define CE_ATTR_DIS_INTR BIT(3)
+
+/* no interrupt, only polling */
+#define CE_ATTR_POLL BIT(4)
/* Attributes of an instance of a Copy Engine */
struct ce_attr {
@@ -192,7 +192,7 @@ static struct ce_attr host_ce_config_wlan[] = {
/* CE7: ce_diag, the Diagnostic Window */
{
- .flags = CE_ATTR_FLAGS,
+ .flags = CE_ATTR_FLAGS | CE_ATTR_POLL,
.src_nentries = 2,
.src_sz_max = DIAG_TRANSFER_LIMIT,
.dest_nentries = 2,
Existing copy engine interrupt enable logic assumes that last CE is using polling mode and due to this interrupt for last copy engine are always disabled. WCN3990 uses last CE for pktlog and interrupt remains disabled with existing logic. To mitigate this issue, introduce CE_ATTR_POLL flag and control the interrupt based on the flag which can be set in ce_attr. Testing: Tested on WCN3990 and QCA6174 HW. Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1, WLAN.RM.4.4.1-00109-QCARMSWPZ-1 Signed-off-by: Govind Singh <govinds@codeaurora.org> --- drivers/net/wireless/ath/ath10k/ce.c | 18 ++++++++++++++---- drivers/net/wireless/ath/ath10k/ce.h | 11 +++++++---- drivers/net/wireless/ath/ath10k/pci.c | 2 +- 3 files changed, 22 insertions(+), 9 deletions(-)