| Context |
Check |
Description |
| tedd_an/pre-ci_am |
success
|
Success
|
| tedd_an/checkpatch |
success
|
Checkpatch PASS
|
| tedd_an/gitlint |
success
|
Gitlint PASS
|
| tedd_an/subjectprefix |
success
|
PASS
|
| tedd_an/buildkernel |
success
|
Build Kernel PASS
|
| tedd_an/buildkernel32 |
success
|
Build Kernel32 PASS
|
| tedd_an/incremental_build |
success
|
Pass
|
| tedd_an/testrunnersetup |
success
|
Test Runner Setup PASS
|
| tedd_an/testrunnerl2cap-tester |
success
|
Total: 40, Passed: 40 (100.0%), Failed: 0, Not Run: 0
|
| tedd_an/testrunnerbnep-tester |
success
|
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
|
| tedd_an/testrunnermgmt-tester |
success
|
Total: 493, Passed: 493 (100.0%), Failed: 0, Not Run: 0
|
| tedd_an/testrunnerrfcomm-tester |
success
|
Total: 10, Passed: 10 (100.0%), Failed: 0, Not Run: 0
|
| tedd_an/testrunnersco-tester |
success
|
Total: 12, Passed: 12 (100.0%), Failed: 0, Not Run: 0
|
| tedd_an/testrunnersmp-tester |
success
|
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
|
| tedd_an/testrunneruserchan-tester |
success
|
Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0
|
@@ -422,6 +422,10 @@ static const struct usb_device_id blacklist_table[] = {
{ USB_DEVICE(0x04ca, 0x4006), .driver_info = BTUSB_REALTEK |
BTUSB_WIDEBAND_SPEECH },
+ /* Realtek 8852BE Bluetooth devices */
+ { USB_DEVICE(0x0bda, 0xb85b), .driver_info = BTUSB_REALTEK |
+ BTUSB_WIDEBAND_SPEECH },
+
/* Realtek Bluetooth devices */
{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
.driver_info = BTUSB_REALTEK },
This Realtek device has both wifi and BT components. The latter reports a USB ID of 0bda:b85b, which is not in the table. BT device description in /sys/kernel/debug/usb/devices contains the following entries: T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=b85b Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Meng Tang <tangmeng@uniontech.com> --- drivers/bluetooth/btusb.c | 4 ++++ 1 file changed, 4 insertions(+)