@@ -826,11 +826,15 @@ EXPORT_SYMBOL_GPL(qca_uart_setup);
int qca_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr)
{
+ bdaddr_t bdaddr_swapped;
struct sk_buff *skb;
int err;
- skb = __hci_cmd_sync_ev(hdev, EDL_WRITE_BD_ADDR_OPCODE, 6, bdaddr,
- HCI_EV_VENDOR, HCI_INIT_TIMEOUT);
+ baswap(&bdaddr_swapped, bdaddr);
+
+ skb = __hci_cmd_sync_ev(hdev, EDL_WRITE_BD_ADDR_OPCODE, 6,
+ &bdaddr_swapped, HCI_EV_VENDOR,
+ HCI_INIT_TIMEOUT);
if (IS_ERR(skb)) {
err = PTR_ERR(skb);
bt_dev_err(hdev, "QCA Change address cmd failed (%d)", err);
@@ -225,6 +225,7 @@ struct qca_serdev {
struct qca_power *bt_power;
u32 init_speed;
u32 oper_speed;
+ bool bdaddr_property_broken;
const char *firmware_name;
};
@@ -1842,6 +1843,7 @@ static int qca_setup(struct hci_uart *hu)
const char *firmware_name = qca_get_firmware_name(hu);
int ret;
struct qca_btsoc_version ver;
+ struct qca_serdev *qcadev;
const char *soc_name;
ret = qca_check_speeds(hu);
@@ -1904,6 +1906,11 @@ static int qca_setup(struct hci_uart *hu)
case QCA_WCN6855:
case QCA_WCN7850:
set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
+
+ qcadev = serdev_device_get_drvdata(hu->serdev);
+ if (qcadev->bdaddr_property_broken)
+ set_bit(HCI_QUIRK_BDADDR_PROPERTY_BROKEN, &hdev->quirks);
+
hci_set_aosp_capable(hdev);
ret = qca_read_soc_version(hdev, &ver, soc_type);
@@ -2284,6 +2291,9 @@ static int qca_serdev_probe(struct serdev_device *serdev)
if (!qcadev->oper_speed)
BT_DBG("UART will pick default operating speed");
+ qcadev->bdaddr_property_broken = device_property_read_bool(&serdev->dev,
+ "qcom,local-bd-address-broken");
+
if (data)
qcadev->btsoc_type = data->soc_type;
else
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth device address in big-endian order when setting it using the EDL_WRITE_BD_ADDR_OPCODE command. Presumably, this is the case for all non-ROME devices which all use the EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which use a different command and expect the address in little-endian order). Reverse the little-endian address before setting it to make sure that the address can be configured using tools like btmgmt or using the 'local-bd-address' devicetree property. Note that this can potentially break systems with boot firmware which has started relying on the broken behaviour and is incorrectly passing the address via devicetree in big-endian order. The only device affected by this should be the WCN3991 used in some Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep, the new 'qcom,local-bd-address-broken' property can be used to determine if the firmware is buggy so that the underlying driver bug can be fixed without breaking backwards compatibility. Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so that the address is reversed when parsing the address property. Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address") Cc: stable@vger.kernel.org # 5.1 Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com> Cc: Matthias Kaehlcke <mka@chromium.org> Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180 Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> --- drivers/bluetooth/btqca.c | 8 ++++++-- drivers/bluetooth/hci_qca.c | 10 ++++++++++ 2 files changed, 16 insertions(+), 2 deletions(-)