@@ -19,6 +19,15 @@ memory@48000000 {
reg = <0x0 0x48000000 0x0 0x38000000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
reg_3p3v: regulator1 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
@@ -27,8 +36,103 @@ reg_3p3v: regulator1 {
regulator-boot-on;
regulator-always-on;
};
+
+#if !(SW_SW0_DEV_SEL)
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ states = <3300000 1>, <1800000 0>;
+ regulator-boot-on;
+ gpios = <&pinctrl RZG2L_GPIO(6, 2) GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ };
+#endif
};
&extal_clk {
clock-frequency = <24000000>;
};
+
+&pinctrl {
+ sdhi0_emmc_pins: sd0emmc {
+ sd0_emmc_data {
+ pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+ "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
+ power-source = <1800>;
+ };
+
+ sd0_emmc_ctrl {
+ pins = "SD0_CLK", "SD0_CMD";
+ power-source = <1800>;
+ };
+
+ sd0_emmc_rst {
+ pins = "SD0_RST#";
+ power-source = <1800>;
+ };
+ };
+
+ sdhi0_pins: sd0 {
+ sd0_data {
+ pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+ power-source = <3300>;
+ };
+
+ sd0_ctrl {
+ pins = "SD0_CLK", "SD0_CMD";
+ power-source = <3300>;
+ };
+
+ sd0_mux {
+ pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */
+ };
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ sd0_data_uhs {
+ pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+ power-source = <1800>;
+ };
+
+ sd0_ctrl_uhs {
+ pins = "SD0_CLK", "SD0_CMD";
+ power-source = <1800>;
+ };
+
+ sd0_mux_uhs {
+ pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */
+ };
+ };
+};
+
+#if (SW_SW0_DEV_SEL)
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_emmc_pins>;
+ pinctrl-1 = <&sdhi0_emmc_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ fixed-emmc-driver-type = <1>;
+ status = "okay";
+};
+#else
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+#endif
@@ -5,6 +5,14 @@
* Copyright (C) 2022 Renesas Electronics Corp.
*/
+/*
+ * DIP-Switch SW1 setting
+ * 1 : High; 0: Low
+ * SW1-2 : SW_SD0_DEV_SEL (0: uSD; 1: eMMC)
+ * Please change below macros according to SW1 setting
+ */
+#define SW_SW0_DEV_SEL 1
+
#include "rzg2ul-smarc-som.dtsi"
#include "rzg2ul-smarc-pinfunction.dtsi"
#include "rz-smarc-common.dtsi"