diff mbox series

[5.10.y-cip,47/47] arm64: dts: renesas: rzg3s-smarc-som: Guard Ethernet IRQ GPIO hogs

Message ID 20240529081039.639010-48-claudiu.beznea.uj@bp.renesas.com (mailing list archive)
State New
Headers show
Series Add Ethernet support for Renesas RZ/G3S SoC | expand

Commit Message

Claudiu Beznea May 29, 2024, 8:10 a.m. UTC
From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

commit 150d81f7a260f36c118cbec253fdd493c671dc29 upstream.

Ethernet IRQ GPIOs are marked as GPIO hogs.  Thus, these GPIOs are
requested at probe time without considering if there are other
peripherals that need them.  The Ethernet IRQ GPIOs are shared with
SDHI2.  Selection between Ethernet and SDHI2 is done through a hardware
switch.  To avoid scenarios where one wants to boot with SDHI2 support
and some SDHI pins are not propertly configured because of the GPIO
hogs, guard the Ethernet IRQ GPIO hogs with the proper build flag.

Fixes: 932ff0c802c6 ("arm64: dts: renesas: rzg3s-smarc-som: Enable the Ethernet interfaces")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240208124300.2740313-13-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---
 arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
index f062d4ad78b7..d33ab4c88787 100644
--- a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
@@ -193,12 +193,14 @@  &sdhi2 {
 #endif
 
 &pinctrl {
+#if SW_CONFIG3 == SW_ON
 	eth0-phy-irq-hog {
 		gpio-hog;
 		gpios = <RZG2L_GPIO(12, 0) GPIO_ACTIVE_LOW>;
 		input;
 		line-name = "eth0-phy-irq";
 	};
+#endif
 
 	eth0_pins: eth0 {
 		txc {
@@ -234,12 +236,14 @@  mux {
 		};
 	};
 
+#if SW_CONFIG3 == SW_ON
 	eth1-phy-irq-hog {
 		gpio-hog;
 		gpios = <RZG2L_GPIO(12, 1) GPIO_ACTIVE_LOW>;
 		input;
 		line-name = "eth1-phy-irq";
 	};
+#endif
 
 	eth1_pins: eth1 {
 		txc {