| Message ID | 20240611021511.35315-1-yaoxt.fnst@fujitsu.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v6] cxl/region: check interleave capability | expand |
On 6/10/24 7:15 PM, Yao Xingtao wrote: > Since interleave capability is not verified, if the interleave > capability of a target does not match the region need, committing decoder > should have failed at the device end. > > In order to checkout this error as quickly as possible, driver needs > to check the interleave capability of target during attaching it to > region. > > According to the CXL specification (section 8.2.4.20 CXL HDM Decoder We should specify the revision of the spec in case future section number changes. > Capability Structure), bits 11 and 12 within the 'CXL HDM Decoder > Capability Register' indicate the capability to establish interleaving > in 3, 6, 12, and 16 ways. If these bits are not set, the target cannot > be attached to a region utilizing such interleave ways. > > Additionally, bits 8 and 9 in the same register represent the capability > of the bits used for interleaving in the address, Linux tracks this in the > cxl_port interleave_mask. > > Regarding 'Decoder Protection': > If IW is less than 8 (for interleave ways of 2, 4, 8, 16), the First use of 'IW'. I suggest using 'eIW' and clarify with something like: encoded Interleave Ways (eIW) Should do the same for IG as well below. Once defined, eIW and eIG can be used. > interleave bits start at bit position IG + 8 and end at IG + IW + 8 - 1. > > If the IW is greater than or equal to 8 (for interleave ways of 6, 12), > the interleave bits start at bit position IG + 8 and end at IG + IW - 1. > > When the interleave ways is 1 or 3, all the bits of HPA are used, the > interleave bits are none, the following check is ignored. > > If the interleave mask is insufficient to cover the required interleave > bits, the target cannot be attached to the region. > > Fixes: 384e624bb211 ("cxl/region: Attach endpoint decoders") > Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com> > > --- > > V5[5] -> V6: > -- fix some typo. > -- update comment. > -- set rc when check faild in cxl_port_attach_region(). > > V4[4] -> V5: > -- update comment. > -- add nr_targets check while attaching a port to switch. > -- delete passthrough flag and allow all the capabilities for passthrough > decoders. > > V3[3] -> V4: > -- update comment. > -- optimize the code. > -- add a passthrough flag to mark the passthrough decoder. > > V2[2] -> V3: > -- revert ig_cap_mask to interleave_mask. > -- fix the interleave bits check logical. > > V1[1] -> V2: > -- rename interleave_mask to ig_cap_mask. > -- add a check for interleave granularity. > -- update commit. > -- move hdm caps init to parse_hdm_decoder_caps(). > > [1] > https://lore.kernel.org/linux-cxl/20240401075635.9333-1-yaoxt.fnst@fujitsu.com > > [2] > https://lore.kernel.org/linux-cxl/20240403021747.17260-1-yaoxt.fnst@fujitsu.com > > [3] > https://lore.kernel.org/linux-cxl/20240409022621.29115-1-yaoxt.fnst@fujitsu.com > > [4] > https://lore.kernel.org/linux-cxl/20240422091350.4701-1-yaoxt.fnst@fujitsu.com > > [5] > https://lore.kernel.org/linux-cxl/20240524092740.4260-1-yaoxt.fnst@fujitsu.com > --- > drivers/cxl/core/hdm.c | 10 +++++ > drivers/cxl/core/region.c | 89 +++++++++++++++++++++++++++++++++++++++ > drivers/cxl/cxl.h | 2 + > drivers/cxl/cxlmem.h | 1 + > 4 files changed, 102 insertions(+) > > diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c > index 7d97790b893d..5b7dff19bbfa 100644 > --- a/drivers/cxl/core/hdm.c > +++ b/drivers/cxl/core/hdm.c > @@ -52,6 +52,11 @@ int devm_cxl_add_passthrough_decoder(struct cxl_port *port) > struct cxl_dport *dport = NULL; > int single_port_map[1]; > unsigned long index; > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > + > + /* allow all the interleave capabilities for passthrough decoder */ > + cxlhdm->interleave_mask = GENMASK(14, 8); > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); > > cxlsd = cxl_switch_decoder_alloc(port, 1); > if (IS_ERR(cxlsd)) > @@ -79,6 +84,11 @@ static void parse_hdm_decoder_caps(struct cxl_hdm *cxlhdm) > cxlhdm->interleave_mask |= GENMASK(11, 8); > if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_14_12, hdm_cap)) > cxlhdm->interleave_mask |= GENMASK(14, 12); > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); Should define a mask for this. Probably should have defined masks for all of the open coded BIT() sets. > + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY, hdm_cap)) > + cxlhdm->iw_cap_mask |= BIT(3) | BIT(6) | BIT(12); > + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_16_WAY, hdm_cap)) > + cxlhdm->iw_cap_mask |= BIT(16); > } > > static bool should_emulate_decoders(struct cxl_endpoint_dvsec_info *info) > diff --git a/drivers/cxl/core/region.c b/drivers/cxl/core/region.c > index 5c186e0a39b9..2716678df5db 100644 > --- a/drivers/cxl/core/region.c > +++ b/drivers/cxl/core/region.c > @@ -1101,6 +1101,26 @@ static int cxl_port_attach_region(struct cxl_port *port, > } > cxld = cxl_rr->decoder; > > + /* > + * the number of targets should not exceed the target_count > + * of the decoder > + */ > + if (is_switch_decoder(&cxld->dev)) { > + struct cxl_switch_decoder *cxlsd; > + > + cxlsd = to_cxl_switch_decoder(&cxld->dev); > + if (cxl_rr->nr_targets > cxlsd->nr_targets) { > + dev_dbg(&cxlr->dev, > + "%s:%s %s add: %s:%s @ %d overflows targets: %d\n", > + dev_name(port->uport_dev), dev_name(&port->dev), > + dev_name(&cxld->dev), dev_name(&cxlmd->dev), > + dev_name(&cxled->cxld.dev), pos, > + cxlsd->nr_targets); > + rc = -ENXIO; > + goto out_erase; > + } > + } > + Should this be a seaprate patch? Seems to be outside the purpose of interleave capability check. > rc = cxl_rr_ep_add(cxl_rr, cxled); > if (rc) { > dev_dbg(&cxlr->dev, > @@ -1210,6 +1230,57 @@ static int check_last_peer(struct cxl_endpoint_decoder *cxled, > return 0; > } > > +static int check_interleave_cap(struct cxl_decoder *cxld, int iw, int ig) > +{ > + struct cxl_port *port = to_cxl_port(cxld->dev.parent); > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > + unsigned int interleave_mask; > + u8 eiw; > + u16 eig; > + int rc, high_pos, low_pos; > + > + rc = ways_to_eiw(iw, &eiw); > + if (rc) > + return rc; > + > + if (!test_bit(iw, &cxlhdm->iw_cap_mask)) > + return -ENXIO; This test can be moved above the ways_to_eiw() call? No need to do ways_to_eiw() if this fails? > + > + rc = granularity_to_eig(ig, &eig); > + if (rc) > + return rc; > + > + /* > + * Per CXL specification (8.2.4.20.13 Decoder Protection in r3.1), A nit but it's probably easier to read if you specify the spec revision first Per CXL specification r3.1 (8.2.4.20.13...), DJ > + * if eiw < 8: > + * DPAOFFSET[51: eig + 8] = HPAOFFSET[51: eig + 8 + eiw] > + * DPAOFFSET[eig + 7: 0] = HPAOFFSET[eig + 7: 0] > + * > + * when the eiw is 0, all the bits of HPAOFFSET[51: 0] are used, the > + * interleave bits are none. > + * > + * if eiw >= 8: > + * DPAOFFSET[51: eig + 8] = HPAOFFSET[51: eig + eiw] / 3 > + * DPAOFFSET[eig + 7: 0] = HPAOFFSET[eig + 7: 0] > + * > + * when the eiw is 8, all the bits of HPAOFFSET[51: 0] are used, the > + * interleave bits are none. > + */ > + if (eiw == 0 || eiw == 8) > + return 0; > + > + if (eiw > 8) > + high_pos = eiw + eig - 1; > + else > + high_pos = eiw + eig + 7; > + low_pos = eig + 8; > + interleave_mask = GENMASK(high_pos, low_pos); > + if (interleave_mask & ~cxlhdm->interleave_mask) > + return -ENXIO; > + > + return 0; > +} > + > static int cxl_port_setup_targets(struct cxl_port *port, > struct cxl_region *cxlr, > struct cxl_endpoint_decoder *cxled) > @@ -1360,6 +1431,15 @@ static int cxl_port_setup_targets(struct cxl_port *port, > return -ENXIO; > } > } else { > + rc = check_interleave_cap(cxld, iw, ig); > + if (rc) { > + dev_dbg(&cxlr->dev, > + "%s:%s iw: %d ig: %d is not supported\n", > + dev_name(port->uport_dev), > + dev_name(&port->dev), iw, ig); > + return rc; > + } > + > cxld->interleave_ways = iw; > cxld->interleave_granularity = ig; > cxld->hpa_range = (struct range) { > @@ -1796,6 +1876,15 @@ static int cxl_region_attach(struct cxl_region *cxlr, > struct cxl_dport *dport; > int rc = -ENXIO; > > + rc = check_interleave_cap(&cxled->cxld, p->interleave_ways, > + p->interleave_granularity); > + if (rc) { > + dev_dbg(&cxlr->dev, "%s iw: %d ig: %d is not supported\n", > + dev_name(&cxled->cxld.dev), p->interleave_ways, > + p->interleave_granularity); > + return rc; > + } > + > if (cxled->mode != cxlr->mode) { > dev_dbg(&cxlr->dev, "%s region mode: %d mismatch: %d\n", > dev_name(&cxled->cxld.dev), cxlr->mode, cxled->mode); > diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h > index 036d17db68e0..dc8e46a1fe82 100644 > --- a/drivers/cxl/cxl.h > +++ b/drivers/cxl/cxl.h > @@ -45,6 +45,8 @@ > #define CXL_HDM_DECODER_TARGET_COUNT_MASK GENMASK(7, 4) > #define CXL_HDM_DECODER_INTERLEAVE_11_8 BIT(8) > #define CXL_HDM_DECODER_INTERLEAVE_14_12 BIT(9) > +#define CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY BIT(11) > +#define CXL_HDM_DECODER_INTERLEAVE_16_WAY BIT(12) > #define CXL_HDM_DECODER_CTRL_OFFSET 0x4 > #define CXL_HDM_DECODER_ENABLE BIT(1) > #define CXL_HDM_DECODER0_BASE_LOW_OFFSET(i) (0x20 * (i) + 0x10) > diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h > index 36cee9c30ceb..6b8cf20ff375 100644 > --- a/drivers/cxl/cxlmem.h > +++ b/drivers/cxl/cxlmem.h > @@ -853,6 +853,7 @@ struct cxl_hdm { > unsigned int decoder_count; > unsigned int target_count; > unsigned int interleave_mask; > + unsigned long iw_cap_mask; > struct cxl_port *port; > }; >
> > drivers/cxl/core/hdm.c | 10 +++++ > > drivers/cxl/core/region.c | 89 +++++++++++++++++++++++++++++++++++++++ > > drivers/cxl/cxl.h | 2 + > > drivers/cxl/cxlmem.h | 1 + > > 4 files changed, 102 insertions(+) > > > > diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c > > index 7d97790b893d..5b7dff19bbfa 100644 > > --- a/drivers/cxl/core/hdm.c > > +++ b/drivers/cxl/core/hdm.c > > @@ -52,6 +52,11 @@ int devm_cxl_add_passthrough_decoder(struct cxl_port *port) > > struct cxl_dport *dport = NULL; > > int single_port_map[1]; > > unsigned long index; > > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > > + > > + /* allow all the interleave capabilities for passthrough decoder */ > > + cxlhdm->interleave_mask = GENMASK(14, 8); > > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); > > > > cxlsd = cxl_switch_decoder_alloc(port, 1); > > if (IS_ERR(cxlsd)) > > @@ -79,6 +84,11 @@ static void parse_hdm_decoder_caps(struct cxl_hdm *cxlhdm) > > cxlhdm->interleave_mask |= GENMASK(11, 8); > > if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_14_12, hdm_cap)) > > cxlhdm->interleave_mask |= GENMASK(14, 12); > > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); > > Should define a mask for this. Probably should have defined masks for all of the open coded BIT() sets. I don't agreed. These bits are logically independent specifying each supported value of interleave ways. Put them under a define and I think you end up with less readable code. > > > + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY, hdm_cap)) > > + cxlhdm->iw_cap_mask |= BIT(3) | BIT(6) | BIT(12); > > + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_16_WAY, hdm_cap)) > > + cxlhdm->iw_cap_mask |= BIT(16); > > }
On 6/11/24 9:46 AM, Jonathan Cameron wrote: > >>> drivers/cxl/core/hdm.c | 10 +++++ >>> drivers/cxl/core/region.c | 89 +++++++++++++++++++++++++++++++++++++++ >>> drivers/cxl/cxl.h | 2 + >>> drivers/cxl/cxlmem.h | 1 + >>> 4 files changed, 102 insertions(+) >>> >>> diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c >>> index 7d97790b893d..5b7dff19bbfa 100644 >>> --- a/drivers/cxl/core/hdm.c >>> +++ b/drivers/cxl/core/hdm.c >>> @@ -52,6 +52,11 @@ int devm_cxl_add_passthrough_decoder(struct cxl_port *port) >>> struct cxl_dport *dport = NULL; >>> int single_port_map[1]; >>> unsigned long index; >>> + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); >>> + >>> + /* allow all the interleave capabilities for passthrough decoder */ >>> + cxlhdm->interleave_mask = GENMASK(14, 8); >>> + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); >>> >>> cxlsd = cxl_switch_decoder_alloc(port, 1); >>> if (IS_ERR(cxlsd)) >>> @@ -79,6 +84,11 @@ static void parse_hdm_decoder_caps(struct cxl_hdm *cxlhdm) >>> cxlhdm->interleave_mask |= GENMASK(11, 8); >>> if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_14_12, hdm_cap)) >>> cxlhdm->interleave_mask |= GENMASK(14, 12); >>> + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); >> >> Should define a mask for this. Probably should have defined masks for all of the open coded BIT() sets. > > I don't agreed. These bits are logically independent specifying each > supported value of interleave ways. > Put them under a define and I think you end up with less readable code. > Seeing the 1,2,4,8 being set twice looks like a common pattern. but I don't have a strong opinion on this. >> >>> + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY, hdm_cap)) >>> + cxlhdm->iw_cap_mask |= BIT(3) | BIT(6) | BIT(12); >>> + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_16_WAY, hdm_cap)) >>> + cxlhdm->iw_cap_mask |= BIT(16); >>> } > > > >
Yao Xingtao wrote: > Since interleave capability is not verified, if the interleave > capability of a target does not match the region need, committing decoder > should have failed at the device end. > > In order to checkout this error as quickly as possible, driver needs > to check the interleave capability of target during attaching it to > region. > > According to the CXL specification (section 8.2.4.20 CXL HDM Decoder > Capability Structure), bits 11 and 12 within the 'CXL HDM Decoder > Capability Register' indicate the capability to establish interleaving > in 3, 6, 12, and 16 ways. If these bits are not set, the target cannot > be attached to a region utilizing such interleave ways. > > Additionally, bits 8 and 9 in the same register represent the capability > of the bits used for interleaving in the address, Linux tracks this in the > cxl_port interleave_mask. > > Regarding 'Decoder Protection': > If IW is less than 8 (for interleave ways of 2, 4, 8, 16), the > interleave bits start at bit position IG + 8 and end at IG + IW + 8 - 1. > > If the IW is greater than or equal to 8 (for interleave ways of 6, 12), > the interleave bits start at bit position IG + 8 and end at IG + IW - 1. > > When the interleave ways is 1 or 3, all the bits of HPA are used, the > interleave bits are none, the following check is ignored. > > If the interleave mask is insufficient to cover the required interleave > bits, the target cannot be attached to the region. > > Fixes: 384e624bb211 ("cxl/region: Attach endpoint decoders") > Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com> > > --- > > V5[5] -> V6: > -- fix some typo. > -- update comment. > -- set rc when check faild in cxl_port_attach_region(). > > V4[4] -> V5: > -- update comment. > -- add nr_targets check while attaching a port to switch. > -- delete passthrough flag and allow all the capabilities for passthrough > decoders. > > V3[3] -> V4: > -- update comment. > -- optimize the code. > -- add a passthrough flag to mark the passthrough decoder. > > V2[2] -> V3: > -- revert ig_cap_mask to interleave_mask. > -- fix the interleave bits check logical. > > V1[1] -> V2: > -- rename interleave_mask to ig_cap_mask. > -- add a check for interleave granularity. > -- update commit. > -- move hdm caps init to parse_hdm_decoder_caps(). > > [1] > https://lore.kernel.org/linux-cxl/20240401075635.9333-1-yaoxt.fnst@fujitsu.com > > [2] > https://lore.kernel.org/linux-cxl/20240403021747.17260-1-yaoxt.fnst@fujitsu.com > > [3] > https://lore.kernel.org/linux-cxl/20240409022621.29115-1-yaoxt.fnst@fujitsu.com > > [4] > https://lore.kernel.org/linux-cxl/20240422091350.4701-1-yaoxt.fnst@fujitsu.com > > [5] > https://lore.kernel.org/linux-cxl/20240524092740.4260-1-yaoxt.fnst@fujitsu.com > --- > drivers/cxl/core/hdm.c | 10 +++++ > drivers/cxl/core/region.c | 89 +++++++++++++++++++++++++++++++++++++++ > drivers/cxl/cxl.h | 2 + > drivers/cxl/cxlmem.h | 1 + > 4 files changed, 102 insertions(+) > > diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c > index 7d97790b893d..5b7dff19bbfa 100644 > --- a/drivers/cxl/core/hdm.c > +++ b/drivers/cxl/core/hdm.c > @@ -52,6 +52,11 @@ int devm_cxl_add_passthrough_decoder(struct cxl_port *port) > struct cxl_dport *dport = NULL; > int single_port_map[1]; > unsigned long index; > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > + > + /* allow all the interleave capabilities for passthrough decoder */ This comment is incomplete / misleading: > + cxlhdm->interleave_mask = GENMASK(14, 8); > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); ...because this is not all of the possible interleaves. The precision here is not helpful because it makes it seem as if any of these checks actually matter for a passthrough decoder. So I would be happier if the comment and the code said: /* * Capability checks are moot for passthrough decoders, support any and * all possibilities */ cxlhdm->interleave_mask = ~0U; cxlhdm->iw_cap_mask = ~0UL; > diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h > index 036d17db68e0..dc8e46a1fe82 100644 > --- a/drivers/cxl/cxl.h > +++ b/drivers/cxl/cxl.h > @@ -45,6 +45,8 @@ > #define CXL_HDM_DECODER_TARGET_COUNT_MASK GENMASK(7, 4) > #define CXL_HDM_DECODER_INTERLEAVE_11_8 BIT(8) > #define CXL_HDM_DECODER_INTERLEAVE_14_12 BIT(9) > +#define CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY BIT(11) > +#define CXL_HDM_DECODER_INTERLEAVE_16_WAY BIT(12) > #define CXL_HDM_DECODER_CTRL_OFFSET 0x4 > #define CXL_HDM_DECODER_ENABLE BIT(1) > #define CXL_HDM_DECODER0_BASE_LOW_OFFSET(i) (0x20 * (i) + 0x10) > diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h > index 36cee9c30ceb..6b8cf20ff375 100644 > --- a/drivers/cxl/cxlmem.h > +++ b/drivers/cxl/cxlmem.h > @@ -853,6 +853,7 @@ struct cxl_hdm { > unsigned int decoder_count; > unsigned int target_count; > unsigned int interleave_mask; > + unsigned long iw_cap_mask; Given the code assumes that the reader knows that each bit is identical to a supported interleave value it would be useful to document that assumption here and add some kdoc, something like: /** * struct cxl_hdm - HDM Decoder registers and cached / decoded capabilities * @regs: mapped registers, see devm_cxl_setup_hdm() * @decoder_count: number of decoders for this port * @target_count: for switch decoders, max downstream port targets * @interleave_mask: interleave granularity capabilty, see check_interleave_cap() * @iw_cap_mask: bitmask of supported interleave ways, see check_interleave_cap() */ ...with the above changes you can add: Reviewed-by: Dan Williams <dan.j.williams@intel.com>
> -----Original Message----- > From: Dave Jiang <dave.jiang@intel.com> > Sent: Tuesday, June 11, 2024 11:52 PM > To: Yao, Xingtao/姚 幸涛 <yaoxt.fnst@fujitsu.com>; dave@stgolabs.net; > jonathan.cameron@huawei.com; alison.schofield@intel.com; > vishal.l.verma@intel.com; ira.weiny@intel.com; dan.j.williams@intel.com; > jim.harris@samsung.com > Cc: linux-cxl@vger.kernel.org > Subject: Re: [PATCH v6] cxl/region: check interleave capability > > > > On 6/10/24 7:15 PM, Yao Xingtao wrote: > > Since interleave capability is not verified, if the interleave > > capability of a target does not match the region need, committing decoder > > should have failed at the device end. > > > > In order to checkout this error as quickly as possible, driver needs > > to check the interleave capability of target during attaching it to > > region. > > > > According to the CXL specification (section 8.2.4.20 CXL HDM Decoder > We should specify the revision of the spec in case future section number changes. thanks, will fix. > > > Capability Structure), bits 11 and 12 within the 'CXL HDM Decoder > > Capability Register' indicate the capability to establish interleaving > > in 3, 6, 12, and 16 ways. If these bits are not set, the target cannot > > be attached to a region utilizing such interleave ways. > > > > Additionally, bits 8 and 9 in the same register represent the capability > > of the bits used for interleaving in the address, Linux tracks this in the > > cxl_port interleave_mask. > > > > Regarding 'Decoder Protection': > > If IW is less than 8 (for interleave ways of 2, 4, 8, 16), the > > First use of 'IW'. I suggest using 'eIW' and clarify with something like: > > encoded Interleave Ways (eIW) > > Should do the same for IG as well below. > > Once defined, eIW and eIG can be used. thanks, will fix. > > > interleave bits start at bit position IG + 8 and end at IG + IW + 8 - 1. > > > > If the IW is greater than or equal to 8 (for interleave ways of 6, 12), > > the interleave bits start at bit position IG + 8 and end at IG + IW - 1. > > > > When the interleave ways is 1 or 3, all the bits of HPA are used, the > > interleave bits are none, the following check is ignored. > > > > If the interleave mask is insufficient to cover the required interleave > > bits, the target cannot be attached to the region. > > > > Fixes: 384e624bb211 ("cxl/region: Attach endpoint decoders") > > Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com> > > > > --- > > > > V5[5] -> V6: > > -- fix some typo. > > -- update comment. > > -- set rc when check faild in cxl_port_attach_region(). > > > > V4[4] -> V5: > > -- update comment. > > -- add nr_targets check while attaching a port to switch. > > -- delete passthrough flag and allow all the capabilities for passthrough > > decoders. > > > > V3[3] -> V4: > > -- update comment. > > -- optimize the code. > > -- add a passthrough flag to mark the passthrough decoder. > > > > V2[2] -> V3: > > -- revert ig_cap_mask to interleave_mask. > > -- fix the interleave bits check logical. > > > > V1[1] -> V2: > > -- rename interleave_mask to ig_cap_mask. > > -- add a check for interleave granularity. > > -- update commit. > > -- move hdm caps init to parse_hdm_decoder_caps(). > > > > [1] > > > https://lore.kernel.org/linux-cxl/20240401075635.9333-1-yaoxt.fnst@fujitsu.com > > > > [2] > > > https://lore.kernel.org/linux-cxl/20240403021747.17260-1-yaoxt.fnst@fujitsu.com > > > > [3] > > > https://lore.kernel.org/linux-cxl/20240409022621.29115-1-yaoxt.fnst@fujitsu.com > > > > [4] > > > https://lore.kernel.org/linux-cxl/20240422091350.4701-1-yaoxt.fnst@fujitsu.com > > > > [5] > > > https://lore.kernel.org/linux-cxl/20240524092740.4260-1-yaoxt.fnst@fujitsu.com > > --- > > drivers/cxl/core/hdm.c | 10 +++++ > > drivers/cxl/core/region.c | 89 > +++++++++++++++++++++++++++++++++++++++ > > drivers/cxl/cxl.h | 2 + > > drivers/cxl/cxlmem.h | 1 + > > 4 files changed, 102 insertions(+) > > > > diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c > > index 7d97790b893d..5b7dff19bbfa 100644 > > --- a/drivers/cxl/core/hdm.c > > +++ b/drivers/cxl/core/hdm.c > > @@ -52,6 +52,11 @@ int devm_cxl_add_passthrough_decoder(struct cxl_port > *port) > > struct cxl_dport *dport = NULL; > > int single_port_map[1]; > > unsigned long index; > > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > > + > > + /* allow all the interleave capabilities for passthrough decoder */ > > + cxlhdm->interleave_mask = GENMASK(14, 8); > > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); > > > > cxlsd = cxl_switch_decoder_alloc(port, 1); > > if (IS_ERR(cxlsd)) > > @@ -79,6 +84,11 @@ static void parse_hdm_decoder_caps(struct cxl_hdm > *cxlhdm) > > cxlhdm->interleave_mask |= GENMASK(11, 8); > > if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_14_12, hdm_cap)) > > cxlhdm->interleave_mask |= GENMASK(14, 12); > > + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); > > Should define a mask for this. Probably should have defined masks for all of the > open coded BIT() sets. > > > + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY, > hdm_cap)) > > + cxlhdm->iw_cap_mask |= BIT(3) | BIT(6) | BIT(12); > > + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_16_WAY, hdm_cap)) > > + cxlhdm->iw_cap_mask |= BIT(16); > > } > > > > static bool should_emulate_decoders(struct cxl_endpoint_dvsec_info *info) > > diff --git a/drivers/cxl/core/region.c b/drivers/cxl/core/region.c > > index 5c186e0a39b9..2716678df5db 100644 > > --- a/drivers/cxl/core/region.c > > +++ b/drivers/cxl/core/region.c > > @@ -1101,6 +1101,26 @@ static int cxl_port_attach_region(struct cxl_port *port, > > } > > cxld = cxl_rr->decoder; > > > > + /* > > + * the number of targets should not exceed the target_count > > + * of the decoder > > + */ > > + if (is_switch_decoder(&cxld->dev)) { > > + struct cxl_switch_decoder *cxlsd; > > + > > + cxlsd = to_cxl_switch_decoder(&cxld->dev); > > + if (cxl_rr->nr_targets > cxlsd->nr_targets) { > > + dev_dbg(&cxlr->dev, > > + "%s:%s %s add: %s:%s @ %d overflows > targets: %d\n", > > + dev_name(port->uport_dev), > dev_name(&port->dev), > > + dev_name(&cxld->dev), > dev_name(&cxlmd->dev), > > + dev_name(&cxled->cxld.dev), pos, > > + cxlsd->nr_targets); > > + rc = -ENXIO; > > + goto out_erase; > > + } > > + } > > + > > Should this be a seaprate patch? Seems to be outside the purpose of interleave > capability check. in this case, the cxl_rr->nr_targets is increasing, it cannot represent interleave ways, and the granularity is unknown, so I think it is better to do this check here. > > > rc = cxl_rr_ep_add(cxl_rr, cxled); > > if (rc) { > > dev_dbg(&cxlr->dev, > > @@ -1210,6 +1230,57 @@ static int check_last_peer(struct > cxl_endpoint_decoder *cxled, > > return 0; > > } > > > > +static int check_interleave_cap(struct cxl_decoder *cxld, int iw, int ig) > > +{ > > + struct cxl_port *port = to_cxl_port(cxld->dev.parent); > > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > > + unsigned int interleave_mask; > > + u8 eiw; > > + u16 eig; > > + int rc, high_pos, low_pos; > > + > > + rc = ways_to_eiw(iw, &eiw); > > + if (rc) > > + return rc; > > + > > + if (!test_bit(iw, &cxlhdm->iw_cap_mask)) > > + return -ENXIO; > > This test can be moved above the ways_to_eiw() call? No need to do ways_to_eiw() > if this fails? in my opinion, the interleave ways should be valid first. > > > + > > + rc = granularity_to_eig(ig, &eig); > > + if (rc) > > + return rc; > > + > > + /* > > + * Per CXL specification (8.2.4.20.13 Decoder Protection in r3.1), > > A nit but it's probably easier to read if you specify the spec revision first > Per CXL specification r3.1 (8.2.4.20.13...), thanks, will fix. > > DJ > > + * if eiw < 8: > > + * DPAOFFSET[51: eig + 8] = HPAOFFSET[51: eig + 8 + eiw] > > + * DPAOFFSET[eig + 7: 0] = HPAOFFSET[eig + 7: 0] > > + * > > + * when the eiw is 0, all the bits of HPAOFFSET[51: 0] are used, the > > + * interleave bits are none. > > + * > > + * if eiw >= 8: > > + * DPAOFFSET[51: eig + 8] = HPAOFFSET[51: eig + eiw] / 3 > > + * DPAOFFSET[eig + 7: 0] = HPAOFFSET[eig + 7: 0] > > + * > > + * when the eiw is 8, all the bits of HPAOFFSET[51: 0] are used, the > > + * interleave bits are none. > > + */ > > + if (eiw == 0 || eiw == 8) > > + return 0; > > + > > + if (eiw > 8) > > + high_pos = eiw + eig - 1; > > + else > > + high_pos = eiw + eig + 7; > > + low_pos = eig + 8; > > + interleave_mask = GENMASK(high_pos, low_pos); > > + if (interleave_mask & ~cxlhdm->interleave_mask) > > + return -ENXIO; > > + > > + return 0; > > +} > > + > > static int cxl_port_setup_targets(struct cxl_port *port, > > struct cxl_region *cxlr, > > struct cxl_endpoint_decoder *cxled) > > @@ -1360,6 +1431,15 @@ static int cxl_port_setup_targets(struct cxl_port *port, > > return -ENXIO; > > } > > } else { > > + rc = check_interleave_cap(cxld, iw, ig); > > + if (rc) { > > + dev_dbg(&cxlr->dev, > > + "%s:%s iw: %d ig: %d is not supported\n", > > + dev_name(port->uport_dev), > > + dev_name(&port->dev), iw, ig); > > + return rc; > > + } > > + > > cxld->interleave_ways = iw; > > cxld->interleave_granularity = ig; > > cxld->hpa_range = (struct range) { > > @@ -1796,6 +1876,15 @@ static int cxl_region_attach(struct cxl_region *cxlr, > > struct cxl_dport *dport; > > int rc = -ENXIO; > > > > + rc = check_interleave_cap(&cxled->cxld, p->interleave_ways, > > + p->interleave_granularity); > > + if (rc) { > > + dev_dbg(&cxlr->dev, "%s iw: %d ig: %d is not supported\n", > > + dev_name(&cxled->cxld.dev), p->interleave_ways, > > + p->interleave_granularity); > > + return rc; > > + } > > + > > if (cxled->mode != cxlr->mode) { > > dev_dbg(&cxlr->dev, "%s region mode: %d mismatch: %d\n", > > dev_name(&cxled->cxld.dev), cxlr->mode, > cxled->mode); > > diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h > > index 036d17db68e0..dc8e46a1fe82 100644 > > --- a/drivers/cxl/cxl.h > > +++ b/drivers/cxl/cxl.h > > @@ -45,6 +45,8 @@ > > #define CXL_HDM_DECODER_TARGET_COUNT_MASK GENMASK(7, 4) > > #define CXL_HDM_DECODER_INTERLEAVE_11_8 BIT(8) > > #define CXL_HDM_DECODER_INTERLEAVE_14_12 BIT(9) > > +#define CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY BIT(11) > > +#define CXL_HDM_DECODER_INTERLEAVE_16_WAY BIT(12) > > #define CXL_HDM_DECODER_CTRL_OFFSET 0x4 > > #define CXL_HDM_DECODER_ENABLE BIT(1) > > #define CXL_HDM_DECODER0_BASE_LOW_OFFSET(i) (0x20 * (i) + 0x10) > > diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h > > index 36cee9c30ceb..6b8cf20ff375 100644 > > --- a/drivers/cxl/cxlmem.h > > +++ b/drivers/cxl/cxlmem.h > > @@ -853,6 +853,7 @@ struct cxl_hdm { > > unsigned int decoder_count; > > unsigned int target_count; > > unsigned int interleave_mask; > > + unsigned long iw_cap_mask; > > struct cxl_port *port; > > }; > >
Xingtao Yao (Fujitsu) wrote: [..] > > > diff --git a/drivers/cxl/core/region.c b/drivers/cxl/core/region.c > > > index 5c186e0a39b9..2716678df5db 100644 > > > --- a/drivers/cxl/core/region.c > > > +++ b/drivers/cxl/core/region.c > > > @@ -1101,6 +1101,26 @@ static int cxl_port_attach_region(struct cxl_port *port, > > > } > > > cxld = cxl_rr->decoder; > > > > > > + /* > > > + * the number of targets should not exceed the target_count > > > + * of the decoder > > > + */ > > > + if (is_switch_decoder(&cxld->dev)) { > > > + struct cxl_switch_decoder *cxlsd; > > > + > > > + cxlsd = to_cxl_switch_decoder(&cxld->dev); > > > + if (cxl_rr->nr_targets > cxlsd->nr_targets) { > > > + dev_dbg(&cxlr->dev, > > > + "%s:%s %s add: %s:%s @ %d overflows > > targets: %d\n", > > > + dev_name(port->uport_dev), > > dev_name(&port->dev), > > > + dev_name(&cxld->dev), > > dev_name(&cxlmd->dev), > > > + dev_name(&cxled->cxld.dev), pos, > > > + cxlsd->nr_targets); > > > + rc = -ENXIO; > > > + goto out_erase; > > > + } > > > + } > > > + > > > > Should this be a seaprate patch? Seems to be outside the purpose of interleave > > capability check. > in this case, the cxl_rr->nr_targets is increasing, it cannot represent interleave ways, and the > granularity is unknown, so I think it is better to do this check here. Right, the decoder's target count *is* a capability, so might as well include all the capability checks in this fix. > > > > > > rc = cxl_rr_ep_add(cxl_rr, cxled); > > > if (rc) { > > > dev_dbg(&cxlr->dev, > > > @@ -1210,6 +1230,57 @@ static int check_last_peer(struct > > cxl_endpoint_decoder *cxled, > > > return 0; > > > } > > > > > > +static int check_interleave_cap(struct cxl_decoder *cxld, int iw, int ig) > > > +{ > > > + struct cxl_port *port = to_cxl_port(cxld->dev.parent); > > > + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); > > > + unsigned int interleave_mask; > > > + u8 eiw; > > > + u16 eig; > > > + int rc, high_pos, low_pos; > > > + > > > + rc = ways_to_eiw(iw, &eiw); > > > + if (rc) > > > + return rc; > > > + > > > + if (!test_bit(iw, &cxlhdm->iw_cap_mask)) > > > + return -ENXIO; > > > > This test can be moved above the ways_to_eiw() call? No need to do ways_to_eiw() > > if this fails? > in my opinion, the interleave ways should be valid first. The check can just be dropped altogether becuase it is redundant with earlier checks of the same: cxl_port_setup_targets(): https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/cxl/core/region.c#n1297 interleave_ways_store(): https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/cxl/core/region.c#n498
diff --git a/drivers/cxl/core/hdm.c b/drivers/cxl/core/hdm.c index 7d97790b893d..5b7dff19bbfa 100644 --- a/drivers/cxl/core/hdm.c +++ b/drivers/cxl/core/hdm.c @@ -52,6 +52,11 @@ int devm_cxl_add_passthrough_decoder(struct cxl_port *port) struct cxl_dport *dport = NULL; int single_port_map[1]; unsigned long index; + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); + + /* allow all the interleave capabilities for passthrough decoder */ + cxlhdm->interleave_mask = GENMASK(14, 8); + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); cxlsd = cxl_switch_decoder_alloc(port, 1); if (IS_ERR(cxlsd)) @@ -79,6 +84,11 @@ static void parse_hdm_decoder_caps(struct cxl_hdm *cxlhdm) cxlhdm->interleave_mask |= GENMASK(11, 8); if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_14_12, hdm_cap)) cxlhdm->interleave_mask |= GENMASK(14, 12); + cxlhdm->iw_cap_mask = BIT(1) | BIT(2) | BIT(4) | BIT(8); + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY, hdm_cap)) + cxlhdm->iw_cap_mask |= BIT(3) | BIT(6) | BIT(12); + if (FIELD_GET(CXL_HDM_DECODER_INTERLEAVE_16_WAY, hdm_cap)) + cxlhdm->iw_cap_mask |= BIT(16); } static bool should_emulate_decoders(struct cxl_endpoint_dvsec_info *info) diff --git a/drivers/cxl/core/region.c b/drivers/cxl/core/region.c index 5c186e0a39b9..2716678df5db 100644 --- a/drivers/cxl/core/region.c +++ b/drivers/cxl/core/region.c @@ -1101,6 +1101,26 @@ static int cxl_port_attach_region(struct cxl_port *port, } cxld = cxl_rr->decoder; + /* + * the number of targets should not exceed the target_count + * of the decoder + */ + if (is_switch_decoder(&cxld->dev)) { + struct cxl_switch_decoder *cxlsd; + + cxlsd = to_cxl_switch_decoder(&cxld->dev); + if (cxl_rr->nr_targets > cxlsd->nr_targets) { + dev_dbg(&cxlr->dev, + "%s:%s %s add: %s:%s @ %d overflows targets: %d\n", + dev_name(port->uport_dev), dev_name(&port->dev), + dev_name(&cxld->dev), dev_name(&cxlmd->dev), + dev_name(&cxled->cxld.dev), pos, + cxlsd->nr_targets); + rc = -ENXIO; + goto out_erase; + } + } + rc = cxl_rr_ep_add(cxl_rr, cxled); if (rc) { dev_dbg(&cxlr->dev, @@ -1210,6 +1230,57 @@ static int check_last_peer(struct cxl_endpoint_decoder *cxled, return 0; } +static int check_interleave_cap(struct cxl_decoder *cxld, int iw, int ig) +{ + struct cxl_port *port = to_cxl_port(cxld->dev.parent); + struct cxl_hdm *cxlhdm = dev_get_drvdata(&port->dev); + unsigned int interleave_mask; + u8 eiw; + u16 eig; + int rc, high_pos, low_pos; + + rc = ways_to_eiw(iw, &eiw); + if (rc) + return rc; + + if (!test_bit(iw, &cxlhdm->iw_cap_mask)) + return -ENXIO; + + rc = granularity_to_eig(ig, &eig); + if (rc) + return rc; + + /* + * Per CXL specification (8.2.4.20.13 Decoder Protection in r3.1), + * if eiw < 8: + * DPAOFFSET[51: eig + 8] = HPAOFFSET[51: eig + 8 + eiw] + * DPAOFFSET[eig + 7: 0] = HPAOFFSET[eig + 7: 0] + * + * when the eiw is 0, all the bits of HPAOFFSET[51: 0] are used, the + * interleave bits are none. + * + * if eiw >= 8: + * DPAOFFSET[51: eig + 8] = HPAOFFSET[51: eig + eiw] / 3 + * DPAOFFSET[eig + 7: 0] = HPAOFFSET[eig + 7: 0] + * + * when the eiw is 8, all the bits of HPAOFFSET[51: 0] are used, the + * interleave bits are none. + */ + if (eiw == 0 || eiw == 8) + return 0; + + if (eiw > 8) + high_pos = eiw + eig - 1; + else + high_pos = eiw + eig + 7; + low_pos = eig + 8; + interleave_mask = GENMASK(high_pos, low_pos); + if (interleave_mask & ~cxlhdm->interleave_mask) + return -ENXIO; + + return 0; +} + static int cxl_port_setup_targets(struct cxl_port *port, struct cxl_region *cxlr, struct cxl_endpoint_decoder *cxled) @@ -1360,6 +1431,15 @@ static int cxl_port_setup_targets(struct cxl_port *port, return -ENXIO; } } else { + rc = check_interleave_cap(cxld, iw, ig); + if (rc) { + dev_dbg(&cxlr->dev, + "%s:%s iw: %d ig: %d is not supported\n", + dev_name(port->uport_dev), + dev_name(&port->dev), iw, ig); + return rc; + } + cxld->interleave_ways = iw; cxld->interleave_granularity = ig; cxld->hpa_range = (struct range) { @@ -1796,6 +1876,15 @@ static int cxl_region_attach(struct cxl_region *cxlr, struct cxl_dport *dport; int rc = -ENXIO; + rc = check_interleave_cap(&cxled->cxld, p->interleave_ways, + p->interleave_granularity); + if (rc) { + dev_dbg(&cxlr->dev, "%s iw: %d ig: %d is not supported\n", + dev_name(&cxled->cxld.dev), p->interleave_ways, + p->interleave_granularity); + return rc; + } + if (cxled->mode != cxlr->mode) { dev_dbg(&cxlr->dev, "%s region mode: %d mismatch: %d\n", dev_name(&cxled->cxld.dev), cxlr->mode, cxled->mode); diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h index 036d17db68e0..dc8e46a1fe82 100644 --- a/drivers/cxl/cxl.h +++ b/drivers/cxl/cxl.h @@ -45,6 +45,8 @@ #define CXL_HDM_DECODER_TARGET_COUNT_MASK GENMASK(7, 4) #define CXL_HDM_DECODER_INTERLEAVE_11_8 BIT(8) #define CXL_HDM_DECODER_INTERLEAVE_14_12 BIT(9) +#define CXL_HDM_DECODER_INTERLEAVE_3_6_12_WAY BIT(11) +#define CXL_HDM_DECODER_INTERLEAVE_16_WAY BIT(12) #define CXL_HDM_DECODER_CTRL_OFFSET 0x4 #define CXL_HDM_DECODER_ENABLE BIT(1) #define CXL_HDM_DECODER0_BASE_LOW_OFFSET(i) (0x20 * (i) + 0x10) diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h index 36cee9c30ceb..6b8cf20ff375 100644 --- a/drivers/cxl/cxlmem.h +++ b/drivers/cxl/cxlmem.h @@ -853,6 +853,7 @@ struct cxl_hdm { unsigned int decoder_count; unsigned int target_count; unsigned int interleave_mask; + unsigned long iw_cap_mask; struct cxl_port *port; };
Since interleave capability is not verified, if the interleave capability of a target does not match the region need, committing decoder should have failed at the device end. In order to checkout this error as quickly as possible, driver needs to check the interleave capability of target during attaching it to region. According to the CXL specification (section 8.2.4.20 CXL HDM Decoder Capability Structure), bits 11 and 12 within the 'CXL HDM Decoder Capability Register' indicate the capability to establish interleaving in 3, 6, 12, and 16 ways. If these bits are not set, the target cannot be attached to a region utilizing such interleave ways. Additionally, bits 8 and 9 in the same register represent the capability of the bits used for interleaving in the address, Linux tracks this in the cxl_port interleave_mask. Regarding 'Decoder Protection': If IW is less than 8 (for interleave ways of 2, 4, 8, 16), the interleave bits start at bit position IG + 8 and end at IG + IW + 8 - 1. If the IW is greater than or equal to 8 (for interleave ways of 6, 12), the interleave bits start at bit position IG + 8 and end at IG + IW - 1. When the interleave ways is 1 or 3, all the bits of HPA are used, the interleave bits are none, the following check is ignored. If the interleave mask is insufficient to cover the required interleave bits, the target cannot be attached to the region. Fixes: 384e624bb211 ("cxl/region: Attach endpoint decoders") Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com> --- V5[5] -> V6: -- fix some typo. -- update comment. -- set rc when check faild in cxl_port_attach_region(). V4[4] -> V5: -- update comment. -- add nr_targets check while attaching a port to switch. -- delete passthrough flag and allow all the capabilities for passthrough decoders. V3[3] -> V4: -- update comment. -- optimize the code. -- add a passthrough flag to mark the passthrough decoder. V2[2] -> V3: -- revert ig_cap_mask to interleave_mask. -- fix the interleave bits check logical. V1[1] -> V2: -- rename interleave_mask to ig_cap_mask. -- add a check for interleave granularity. -- update commit. -- move hdm caps init to parse_hdm_decoder_caps(). [1] https://lore.kernel.org/linux-cxl/20240401075635.9333-1-yaoxt.fnst@fujitsu.com [2] https://lore.kernel.org/linux-cxl/20240403021747.17260-1-yaoxt.fnst@fujitsu.com [3] https://lore.kernel.org/linux-cxl/20240409022621.29115-1-yaoxt.fnst@fujitsu.com [4] https://lore.kernel.org/linux-cxl/20240422091350.4701-1-yaoxt.fnst@fujitsu.com [5] https://lore.kernel.org/linux-cxl/20240524092740.4260-1-yaoxt.fnst@fujitsu.com --- drivers/cxl/core/hdm.c | 10 +++++ drivers/cxl/core/region.c | 89 +++++++++++++++++++++++++++++++++++++++ drivers/cxl/cxl.h | 2 + drivers/cxl/cxlmem.h | 1 + 4 files changed, 102 insertions(+)