diff --git a/Documentation/devicetree/bindings/sii9234.txt b/Documentation/devicetree/bindings/sii9234.txt
new file mode 100644
index 0000000..4431139
--- /dev/null
+++ b/Documentation/devicetree/bindings/sii9234.txt
@@ -0,0 +1,22 @@
+SiI9234 Mobile HD Link Transmitter
+
+Required properties:
+- compatible : "sil,sii9234".
+- reg : I2C address for TPI interface, use 0x39
+- vcc-supply : regulator that supplies the chip
+- gpio-reset : GPIO connected to RESET_N pin
+- gpio-int : GPIO connected to INT pin
+
+Optional properties:
+- extcon : phandle to extcon that wakes up the chip
+
+Additional compatible properties are also allowed.
+
+Example:
+	sii9234@39 {
+		compatible = "sil,sii9234";
+		reg = <0x39>;
+		vcc-supply = <&vsil>;
+		gpio-reset = <&gpf3 4 0>;
+		gpio-int = <&gpf3 5 0>;
+	};
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 1cb7408..3b7f266 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -515,6 +515,14 @@ config SRAM
 	  the genalloc API. It is supposed to be used for small on-chip SRAM
 	  areas found on many SoCs.
 
+config SII9234
+	tristate "Silicon Image SII9234 Driver"
+	depends on I2C
+	help
+	  Say Y here if you want support for the MHL interface.
+	  It is an I2C driver, that detects connection of MHL bridge
+	  and starts encapsulation of HDMI signal.
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 7eb4b69..145a47a 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -55,3 +55,4 @@ obj-$(CONFIG_SRAM)		+= sram.o
 obj-y				+= mic/
 obj-$(CONFIG_GENWQE)		+= genwqe/
 obj-$(CONFIG_ECHO)		+= echo/
+obj-$(CONFIG_SII9234)		+= sii9234.o
diff --git a/drivers/misc/sii9234.c b/drivers/misc/sii9234.c
new file mode 100644
index 0000000..60b7c66
--- /dev/null
+++ b/drivers/misc/sii9234.c
@@ -0,0 +1,1081 @@
+/*
+ * Copyright (C) 2014 Samsung Electronics
+ *
+ * Author: Tomasz Stanislawski <t.stanislaws@samsung.com>
+ *
+ * Based on sii9234 driver created by:
+ *    Adam Hampson <ahampson@sta.samsung.com>
+ *    Erik Gilling <konkers@android.com>
+ *    Shankar Bandal <shankar.b@samsung.com>
+ *    Dharam Kumar <dharam.kr@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+#include <linux/file.h>
+#include <linux/uaccess.h>
+#include <linux/proc_fs.h>
+#include <linux/extcon.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/extcon.h>
+#include <linux/regulator/machine.h>
+
+/* MHL Tx registers and bits */
+#define MHL_TX_SRST                     0x05
+#define MHL_TX_SYSSTAT_REG              0x09
+#define         RSEN_STATUS             (1<<2)
+#define MHL_TX_INTR1_REG                0x71
+#define         HPD_CHANGE_INT          (1<<6)
+#define         RSEN_CHANGE_INT         (1<<5)
+#define MHL_TX_INTR4_REG                0x74
+#define         RGND_READY_INT          (1<<6)
+#define         VBUS_LOW_INT            (1<<5)
+#define         CBUS_LKOUT_INT          (1<<4)
+#define         MHL_DISC_FAIL_INT       (1<<3)
+#define         MHL_EST_INT             (1<<2)
+#define MHL_TX_INTR1_ENABLE_REG         0x75
+#define         HPD_CHANGE_INT_MASK     (1<<6)
+#define         RSEN_CHANGE_INT_MASK    (1<<5)
+#define MHL_TX_INTR4_ENABLE_REG         0x78
+#define         RGND_READY_MASK         (1<<6)
+#define         CBUS_LKOUT_MASK         (1<<4)
+#define         MHL_DISC_FAIL_MASK      (1<<3)
+#define         MHL_EST_MASK            (1<<2)
+#define MHL_TX_INT_CTRL_REG             0x79
+#define MHL_TX_TMDS_CCTRL               0x80
+#define MHL_TX_DISC_CTRL1_REG           0x90
+#define MHL_TX_DISC_CTRL2_REG           0x91
+#define         SKIP_GND                (1<<6)
+#define         ATT_THRESH_SHIFT        0x04
+#define         ATT_THRESH_MASK         (0x03 << ATT_THRESH_SHIFT)
+#define         USB_D_OEN               (1<<3)
+#define         DEGLITCH_TIME_MASK      0x07
+#define         DEGLITCH_TIME_2MS       0
+#define         DEGLITCH_TIME_4MS       1
+#define         DEGLITCH_TIME_8MS       2
+#define         DEGLITCH_TIME_16MS      3
+#define         DEGLITCH_TIME_40MS      4
+#define         DEGLITCH_TIME_50MS      5
+#define         DEGLITCH_TIME_60MS      6
+#define         DEGLITCH_TIME_128MS     7
+#define MHL_TX_DISC_CTRL3_REG           0x92
+#define MHL_TX_DISC_CTRL4_REG		0x93
+#define MHL_TX_DISC_CTRL5_REG           0x94
+#define MHL_TX_DISC_CTRL6_REG           0x95
+#define         USB_D_OVR               (1<<7)
+#define         USB_ID_OVR              (1<<6)
+#define         DVRFLT_SEL              (1<<5)
+#define         BLOCK_RGND_INT          (1<<4)
+#define         SKIP_DEG                (1<<3)
+#define         CI2CA_POL               (1<<2)
+#define         CI2CA_WKUP              (1<<1)
+#define         SINGLE_ATT              (1<<0)
+#define MHL_TX_DISC_CTRL7_REG           0x96
+#define         USB_D_ODN               (1<<5)
+#define         VBUS_CHECK              (1<<2)
+#define         RGND_INTP_MASK          0x03
+#define         RGND_INTP_OPEN          0
+#define         RGND_INTP_2K            1
+#define         RGND_INTP_1K            2
+#define         RGND_INTP_SHORT         3
+#define MHL_TX_DISC_CTRL8_REG		0x97
+#define MHL_TX_STAT2_REG                0x99
+#define MHL_TX_MHLTX_CTL1_REG           0xA0
+#define MHL_TX_MHLTX_CTL2_REG           0xA1
+#define MHL_TX_MHLTX_CTL4_REG           0xA3
+#define MHL_TX_MHLTX_CTL6_REG           0xA5
+#define MHL_TX_MHLTX_CTL7_REG           0xA6
+
+/* HDMI registers */
+#define HDMI_RX_TMDS0_CCTRL1_REG        0x10
+#define HDMI_RX_TMDS_CLK_EN_REG         0x11
+#define HDMI_RX_TMDS_CH_EN_REG          0x12
+#define HDMI_RX_PLL_CALREFSEL_REG       0x17
+#define HDMI_RX_PLL_VCOCAL_REG          0x1A
+#define HDMI_RX_EQ_DATA0_REG            0x22
+#define HDMI_RX_EQ_DATA1_REG            0x23
+#define HDMI_RX_EQ_DATA2_REG            0x24
+#define HDMI_RX_EQ_DATA3_REG            0x25
+#define HDMI_RX_EQ_DATA4_REG            0x26
+#define HDMI_RX_TMDS_ZONE_CTRL_REG      0x4C
+#define HDMI_RX_TMDS_MODE_CTRL_REG      0x4D
+
+/* CBUS registers */
+#define CBUS_INT_STATUS_1_REG           0x08
+#define CBUS_INTR1_ENABLE_REG		0x09
+#define CBUS_MSC_REQ_ABORT_REASON_REG   0x0D
+#define         SET_HPD_DOWNSTREAM      (1<<6)
+#define CBUS_INT_STATUS_2_REG           0x1E
+#define CBUS_INTR2_ENABLE_REG		0x1F
+#define CBUS_LINK_CONTROL_2_REG         0x31
+#define CBUS_DEVCAP_DEV_STATE		0x80
+#define CBUS_DEVCAP_MHL_VERSION		0x81
+#define CBUS_DEVCAP_DEV_CAT             0x82
+#define CBUS_DEVCAP_ADOPTER_ID_H	0x83
+#define CBUS_DEVCAP_ADOPTER_ID_L	0x84
+#define CBUS_DEVCAP_VID_LINK_MODE	0x85
+#define CBUS_DEVCAP_AUD_LINK_MODE	0x86
+#define CBUS_DEVCAP_VIDEO_TYPE		0x87
+#define CBUS_DEVCAP_LOG_DEV_MAP		0x88
+#define CBUS_DEVCAP_BANDWIDTH		0x89
+#define CBUS_DEVCAP_DEV_FEATURE_FLAG    0x8A
+#define CBUS_DEVCAP_DEVICE_ID_H         0x8B
+#define CBUS_DEVCAP_DEVICE_ID_L         0x8C
+#define CBUS_DEVCAP_SCRATCHPAD_SIZE	0x8D
+#define CBUS_DEVCAP_INT_STAT_SIZE	0x8E
+#define CBUS_DEVCAP_RESERVED		0x8F
+#define CBUS_MHL_STATUS_REG_0           0xB0
+#define CBUS_MHL_STATUS_REG_1           0xB1
+
+/* TPI registers */
+#define TPI_DPD_REG                     0x3D
+
+/* timeouts */
+#define T_SRC_VBUS_CBUS_TO_STABLE	200
+#define T_SRC_CBUS_FLOAT		100
+#define T_SRC_CBUS_DEGLITCH		2
+#define T_SRC_RXSENSE_DEGLITCH		110
+
+enum sii9234_state {
+	ST_OFF,
+	ST_D3,
+	ST_RGND_INIT,
+	ST_RGND_1K,
+	ST_RSEN_HIGH,
+	ST_MHL_ESTABLISHED,
+	ST_FAILURE_DISCOVERY,
+	ST_FAILURE,
+};
+
+struct sii9234 {
+	struct i2c_client *client[4];
+	int i2c_error;
+	int gpio_n_reset;
+	int gpio_int;
+	struct regulator *vcc_supply;
+	int irq;
+
+	enum sii9234_state		state;
+	struct mutex			lock;
+
+	/* Extcon */
+	struct extcon_specific_cable_nb extcon_dev;
+	struct notifier_block extcon_nb;
+	struct work_struct extcon_wq;
+	bool extcon_attached;
+};
+
+enum sii9234_client_id {
+	I2C_MHL,
+	I2C_TPI,
+	I2C_HDMI,
+	I2C_CBUS,
+};
+
+#define sii9234_dev(sii9234) (&(sii9234)->client[I2C_MHL]->dev)
+
+static char *sii9234_client_name[] = {
+	[I2C_MHL] = "MHL",
+	[I2C_TPI] = "TPI",
+	[I2C_HDMI] = "HDMI",
+	[I2C_CBUS] = "CBUS",
+};
+
+static int sii9234_writeb(struct sii9234 *sii9234, int id, int offset,
+			    int value)
+{
+	int ret;
+	struct i2c_client *client = sii9234->client[id];
+	struct device *dev = sii9234_dev(sii9234);
+
+	if (sii9234->i2c_error)
+		return sii9234->i2c_error;
+
+	ret = i2c_smbus_write_byte_data(client, offset, value);
+	if (ret < 0)
+		dev_err(dev, "writeb: %4s[0x%02x] <- 0x%02x\n",
+			sii9234_client_name[id], offset, value);
+	sii9234->i2c_error = ret;
+	return ret;
+}
+
+static int sii9234_writebm(struct sii9234 *sii9234, int id, int offset,
+			    int value, int mask)
+{
+	int ret;
+	struct i2c_client *client = sii9234->client[id];
+	struct device *dev = sii9234_dev(sii9234);
+
+	if (sii9234->i2c_error)
+		return sii9234->i2c_error;
+
+	ret = i2c_smbus_write_byte(client, offset);
+	if (ret < 0) {
+		dev_err(dev, "writebm: %4s[0x%02x] <- 0x%02x\n",
+			sii9234_client_name[id], offset, value);
+		sii9234->i2c_error = ret;
+		return ret;
+	}
+
+	ret = i2c_smbus_read_byte(client);
+	if (ret < 0) {
+		dev_err(dev, "writebm: %4s[0x%02x] <- 0x%02x\n",
+			sii9234_client_name[id], offset, value);
+		sii9234->i2c_error = ret;
+		return ret;
+	}
+
+	value = (value & mask) | (ret & ~mask);
+
+	ret = i2c_smbus_write_byte_data(client, offset, value);
+	if (ret < 0) {
+		dev_err(dev, "writebm: %4s[0x%02x] <- 0x%02x\n",
+			sii9234_client_name[id], offset, value);
+		sii9234->i2c_error = ret;
+	}
+	return ret;
+}
+
+static int sii9234_readb(struct sii9234 *sii9234, int id, int offset)
+{
+	int ret;
+	struct i2c_client *client = sii9234->client[id];
+	struct device *dev = sii9234_dev(sii9234);
+
+	if (sii9234->i2c_error)
+		return sii9234->i2c_error;
+
+	ret = i2c_smbus_write_byte(client, offset);
+	if (ret < 0) {
+		dev_err(dev, "readb: %4s[0x%02x]\n",
+			sii9234_client_name[id], offset);
+		sii9234->i2c_error = ret;
+		return ret;
+	}
+
+	ret = i2c_smbus_read_byte(client);
+	if (ret < 0) {
+		dev_err(dev, "readb: %4s[0x%02x]\n",
+			sii9234_client_name[id], offset);
+		sii9234->i2c_error = ret;
+	}
+
+	return ret;
+}
+
+static int sii9234_clear_error(struct sii9234 *sii9234)
+{
+	int ret = sii9234->i2c_error;
+
+	sii9234->i2c_error = 0;
+	return ret;
+}
+
+#define mhl_tx_writeb(sii9234, offset, value) \
+	sii9234_writeb(sii9234, I2C_MHL, offset, value)
+#define mhl_tx_writebm(sii9234, offset, value, mask) \
+	sii9234_writebm(sii9234, I2C_MHL, offset, value, mask)
+#define mhl_tx_readb(sii9234, offset) \
+	sii9234_readb(sii9234, I2C_MHL, offset)
+#define cbus_writeb(sii9234, offset, value) \
+	sii9234_writeb(sii9234, I2C_CBUS, offset, value)
+#define cbus_writebm(sii9234, offset, value, mask) \
+	sii9234_writebm(sii9234, I2C_CBUS, offset, value, mask)
+#define cbus_readb(sii9234, offset) \
+	sii9234_readb(sii9234, I2C_CBUS, offset)
+#define hdmi_writeb(sii9234, offset, value) \
+	sii9234_writeb(sii9234, I2C_HDMI, offset, value)
+#define hdmi_writebm(sii9234, offset, value, mask) \
+	sii9234_writebm(sii9234, I2C_HDMI, offset, value, mask)
+#define hdmi_readb(sii9234, offset) \
+	sii9234_readb(sii9234, I2C_HDMI, offset)
+#define tpi_writeb(sii9234, offset, value) \
+	sii9234_writeb(sii9234, I2C_TPI, offset, value)
+#define tpi_writebm(sii9234, offset, value, mask) \
+	sii9234_writebm(sii9234, I2C_TPI, offset, value, mask)
+#define tpi_readb(sii9234, offset) \
+	sii9234_readb(sii9234, I2C_TPI, offset)
+
+static u8 sii9234_tmds_control(struct sii9234 *sii9234, bool enable)
+{
+	mhl_tx_writebm(sii9234, MHL_TX_TMDS_CCTRL, enable ? ~0 : 0, 0x10);
+	mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, enable ? ~0 : 0, 0x30);
+	return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_cbus_reset(struct sii9234 *sii9234)
+{
+	int i;
+
+	/* Reset CBUS */
+	mhl_tx_writebm(sii9234, MHL_TX_SRST, ~0, 1 << 3);
+	/* CBUS deglitch - 2ms */
+	msleep(T_SRC_CBUS_DEGLITCH);
+	mhl_tx_writebm(sii9234, MHL_TX_SRST, 0, 1 << 3);
+
+	for (i = 0; i < 4; i++) {
+		/* Enable WRITE_STAT interrupt for writes to all
+		   4 MSC Status registers. */
+		cbus_writeb(sii9234, 0xE0 + i, 0xF2);
+		/*Enable SET_INT interrupt for writes to all
+		   4 MSC Interrupt registers. */
+		cbus_writeb(sii9234, 0xF0 + i, 0xF2);
+	}
+
+	return sii9234_clear_error(sii9234);
+}
+
+/* require to chek mhl imformation of samsung in cbus_init_register*/
+static int sii9234_cbus_init(struct sii9234 *sii9234)
+{
+	cbus_writeb(sii9234, 0x07, 0xF2);
+	cbus_writeb(sii9234, 0x40, 0x03);
+	cbus_writeb(sii9234, 0x42, 0x06);
+	cbus_writeb(sii9234, 0x36, 0x0C);
+	cbus_writeb(sii9234, 0x3D, 0xFD);
+	cbus_writeb(sii9234, 0x1C, 0x01);
+	cbus_writeb(sii9234, 0x1D, 0x0F);
+	cbus_writeb(sii9234, 0x44, 0x02);
+	/* Setup our devcap */
+	/* To meet cts 6.3.10.1 spec */
+	cbus_writeb(sii9234, CBUS_DEVCAP_DEV_STATE, 0x00);
+	/* mhl version 1.1 */
+	cbus_writeb(sii9234, CBUS_DEVCAP_MHL_VERSION, 0x11);
+	cbus_writeb(sii9234, CBUS_DEVCAP_DEV_CAT, 0x02);
+	cbus_writeb(sii9234, CBUS_DEVCAP_ADOPTER_ID_H, 0x01);
+	cbus_writeb(sii9234, CBUS_DEVCAP_ADOPTER_ID_L, 0x41);
+	/* YCbCr444, RGB444 */
+	cbus_writeb(sii9234, CBUS_DEVCAP_VID_LINK_MODE, 0x03);
+	cbus_writeb(sii9234, CBUS_DEVCAP_VIDEO_TYPE, 0);
+	cbus_writeb(sii9234, CBUS_DEVCAP_LOG_DEV_MAP, 0x80);
+	cbus_writeb(sii9234, CBUS_DEVCAP_BANDWIDTH, 0x0F);
+	cbus_writeb(sii9234, CBUS_DEVCAP_DEV_FEATURE_FLAG, 0x07);
+	cbus_writeb(sii9234, CBUS_DEVCAP_DEVICE_ID_H, 0x0);
+	cbus_writeb(sii9234, CBUS_DEVCAP_DEVICE_ID_L, 0x0);
+	cbus_writeb(sii9234, CBUS_DEVCAP_SCRATCHPAD_SIZE, 0x10);
+	cbus_writeb(sii9234, CBUS_DEVCAP_INT_STAT_SIZE, 0x33);
+	cbus_writeb(sii9234, CBUS_DEVCAP_RESERVED, 0);
+	cbus_writebm(sii9234, 0x31, 0x0C, 0x0C);
+	cbus_writeb(sii9234, 0x30, 0x01);
+	cbus_writebm(sii9234, 0x3C, 0x30, 0x38);
+	cbus_writebm(sii9234, 0x22, 0x0D, 0x0F);
+	cbus_writebm(sii9234, 0x2E, 0x15, 0x15);
+	cbus_writeb(sii9234, CBUS_INTR1_ENABLE_REG, 0);
+	cbus_writeb(sii9234, CBUS_INTR2_ENABLE_REG, 0);
+
+	return sii9234_clear_error(sii9234);
+}
+
+static void force_usb_id_switch_open(struct sii9234 *sii9234)
+{
+	/*Disable CBUS discovery */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, 0, 0x01);
+	/*Force USB ID switch to open */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, ~0, USB_ID_OVR);
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL3_REG, ~0, 0x86);
+	/*Force upstream HPD to 0 when not in MHL mode. */
+	mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, 0, 0x30);
+}
+
+static void release_usb_id_switch_open(struct sii9234 *sii9234)
+{
+	msleep(T_SRC_CBUS_FLOAT);
+	/* clear USB ID switch to open */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, 0, USB_ID_OVR);
+	/* Enable CBUS discovery */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, ~0, 0x01);
+}
+
+static int sii9234_power_init(struct sii9234 *sii9234)
+{
+	/* Force the SiI9234 into the D0 state. */
+	tpi_writeb(sii9234, TPI_DPD_REG, 0x3F);
+	/* Enable TxPLL Clock */
+	hdmi_writeb(sii9234, HDMI_RX_TMDS_CLK_EN_REG, 0x01);
+	/* Enable Tx Clock Path & Equalizer */
+	hdmi_writeb(sii9234, HDMI_RX_TMDS_CH_EN_REG, 0x15);
+	/* Power Up TMDS */
+	mhl_tx_writeb(sii9234, 0x08, 0x35);
+	return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_hdmi_init(struct sii9234 *sii9234)
+{
+	/* Analog PLL Control bits 5:4 = 2b00 as per char. team. */
+	hdmi_writeb(sii9234, HDMI_RX_TMDS0_CCTRL1_REG, 0xC1);
+	/* PLL Calrefsel */
+	hdmi_writeb(sii9234, HDMI_RX_PLL_CALREFSEL_REG, 0x03);
+	/* VCO Cal */
+	hdmi_writeb(sii9234, HDMI_RX_PLL_VCOCAL_REG, 0x20);
+	/* Auto EQ */
+	hdmi_writeb(sii9234, HDMI_RX_EQ_DATA0_REG, 0x8A);
+	/* Auto EQ */
+	hdmi_writeb(sii9234, HDMI_RX_EQ_DATA1_REG, 0x6A);
+	/* Auto EQ */
+	hdmi_writeb(sii9234, HDMI_RX_EQ_DATA2_REG, 0xAA);
+	/* Auto EQ */
+	hdmi_writeb(sii9234, HDMI_RX_EQ_DATA3_REG, 0xCA);
+	/* Auto EQ */
+	hdmi_writeb(sii9234, HDMI_RX_EQ_DATA4_REG, 0xEA);
+	/* Manual zone */
+	hdmi_writeb(sii9234, HDMI_RX_TMDS_ZONE_CTRL_REG, 0xA0);
+	/* PLL Mode Value */
+	hdmi_writeb(sii9234, HDMI_RX_TMDS_MODE_CTRL_REG, 0x00);
+	mhl_tx_writeb(sii9234, MHL_TX_TMDS_CCTRL, 0x34);
+	hdmi_writeb(sii9234, 0x45, 0x44);
+	/* Rx PLL BW ~ 4MHz */
+	hdmi_writeb(sii9234, 0x31, 0x0A);
+	/* Analog PLL Control * bits 5:4 = 2b00 as per char. team. */
+	hdmi_writeb(sii9234, HDMI_RX_TMDS0_CCTRL1_REG, 0xC1);
+
+	return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_mhl_tx_ctl_int(struct sii9234 *sii9234)
+{
+	mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL1_REG, 0xD0);
+	mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL2_REG, 0xFC);
+	mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL4_REG, 0xEB);
+	mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL7_REG, 0x0C);
+	return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_reset(struct sii9234 *sii9234)
+{
+	int ret;
+
+	sii9234_clear_error(sii9234);
+
+	ret = sii9234_power_init(sii9234);
+	if (ret < 0)
+		return ret;
+	ret = sii9234_cbus_reset(sii9234);
+	if (ret < 0)
+		return ret;
+	ret = sii9234_hdmi_init(sii9234);
+	if (ret < 0)
+		return ret;
+	ret = sii9234_mhl_tx_ctl_int(sii9234);
+	if (ret < 0)
+		return ret;
+
+	/* Enable HDCP Compliance safety */
+	mhl_tx_writeb(sii9234, 0x2B, 0x01);
+	/* CBUS discovery cycle time for each drive and float = 150us */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, 0x04, 0x06);
+	/* Clear bit 6 (reg_skip_rgnd) */
+	mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL2_REG, (1 << 7) /* Reserved */
+		| 2 << ATT_THRESH_SHIFT | DEGLITCH_TIME_50MS);
+	/* Changed from 66 to 65 for 94[1:0] = 01 = 5k reg_cbusmhl_pup_sel */
+	/* 1.8V CBUS VTH & GND threshold */
+	/*To meet CTS 3.3.7.2 spec */
+	mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL5_REG, 0x77);
+	/* set bit 2 and 3, which is Initiator Timeout */
+	cbus_writebm(sii9234, CBUS_LINK_CONTROL_2_REG, ~0, 0x0C);
+	mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL6_REG, 0xA0);
+	/* RGND & single discovery attempt (RGND blocking) */
+	mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL6_REG, BLOCK_RGND_INT |
+			       DVRFLT_SEL | SINGLE_ATT);
+	/* Use VBUS path of discovery state machine */
+	mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL8_REG, 0);
+	/* 0x92[3] sets the CBUS / ID switch */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, ~0, USB_ID_OVR);
+	/* To allow RGND engine to operate correctly.
+	 * When moving the chip from D2 to D0 (power up, init regs)
+	 * the values should be
+	 * 94[1:0] = 01  reg_cbusmhl_pup_sel[1:0] should be set for 5k
+	 * 93[7:6] = 10  reg_cbusdisc_pup_sel[1:0] should be
+	 * set for 10k (default)
+	 * 93[5:4] = 00  reg_cbusidle_pup_sel[1:0] = open (default)
+	 */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL3_REG, ~0, 0x86);
+	/* change from CC to 8C to match 5K */
+	/*To meet CTS 3.3.72 spec */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL4_REG, ~0, 0x8C);
+	/* Configure the interrupt as active high */
+	mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, 0, 0x06);
+
+	msleep(25);
+
+	/* release usb_id switch */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, 0,  USB_ID_OVR);
+	mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL1_REG, 0x27);
+
+	ret = sii9234_clear_error(sii9234);
+	if (ret < 0)
+		return ret;
+	ret = sii9234_cbus_init(sii9234);
+	if (ret < 0)
+		return ret;
+
+	/* Enable Auto soft reset on SCDT = 0 */
+	mhl_tx_writeb(sii9234, 0x05, 0x04);
+	/* HDMI Transcode mode enable */
+	mhl_tx_writeb(sii9234, 0x0D, 0x1C);
+	mhl_tx_writeb(sii9234, MHL_TX_INTR4_ENABLE_REG,
+			       RGND_READY_MASK | CBUS_LKOUT_MASK |
+			       MHL_DISC_FAIL_MASK | MHL_EST_MASK);
+	mhl_tx_writeb(sii9234, MHL_TX_INTR1_ENABLE_REG, 0x60);
+
+	/* this point is very importand before megsure RGND impedance */
+	force_usb_id_switch_open(sii9234);
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL4_REG, 0, 0xF0);
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL5_REG, 0, 0x03);
+	release_usb_id_switch_open(sii9234);
+	/*end of this */
+
+	/* Force upstream HPD to 0 when not in MHL mode */
+	mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, 0, 1 << 5);
+	mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, ~0, 1 << 4);
+
+	return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_goto_d3(struct sii9234 *sii9234)
+{
+	int ret;
+	struct device *dev = sii9234_dev(sii9234);
+
+	dev_dbg(dev, "sii9234: detection started d3\n");
+
+	ret = sii9234_reset(sii9234);
+	if (ret < 0)
+		goto exit;
+
+	hdmi_writeb(sii9234, 0x01, 0x03);
+	tpi_writebm(sii9234, TPI_DPD_REG, 0, 1);
+	/* I2C above is expected to fail because power goes down */
+	sii9234_clear_error(sii9234);
+
+	sii9234->state = ST_D3;
+
+	return 0;
+ exit:
+	dev_err(dev, "sii9234_goto_d3() failed\n");
+	return -1;
+}
+
+#define sii9234_hw_on(sii9234) \
+	regulator_enable((sii9234)->vcc_supply)
+
+static void sii9234_hw_off(struct sii9234 *sii9234)
+{
+	gpio_direction_output(sii9234->gpio_n_reset, 0);
+	usleep_range(10000, 20000);
+	gpio_direction_output(sii9234->gpio_n_reset, 1);
+	regulator_disable(sii9234->vcc_supply);
+	gpio_direction_output(sii9234->gpio_n_reset, 0);
+}
+
+static void sii9234_hw_reset(struct sii9234 *sii9234)
+{
+	gpio_direction_output(sii9234->gpio_n_reset, 0);
+	usleep_range(10000, 20000);
+	gpio_direction_output(sii9234->gpio_n_reset, 1);
+}
+
+static void sii9234_cable_in(struct sii9234 *sii9234)
+{
+	int ret;
+
+	mutex_lock(&sii9234->lock);
+	if (sii9234->state != ST_OFF)
+		goto unlock;
+	ret = sii9234_hw_on(sii9234);
+	if (ret < 0)
+		goto unlock;
+
+	sii9234_hw_reset(sii9234);
+	sii9234_goto_d3(sii9234);
+	enable_irq(sii9234->irq);
+
+unlock:
+	mutex_unlock(&sii9234->lock);
+}
+
+static void sii9234_cable_out(struct sii9234 *sii9234)
+{
+	mutex_lock(&sii9234->lock);
+
+	if (sii9234->state == ST_OFF)
+		goto unlock;
+
+	disable_irq_nosync(sii9234->irq);
+	tpi_writeb(sii9234, TPI_DPD_REG, 0);
+	/*turn on&off hpd festure for only QCT HDMI */
+	sii9234_hw_off(sii9234);
+
+	sii9234->state = ST_OFF;
+
+unlock:
+	mutex_unlock(&sii9234->lock);
+}
+
+static enum sii9234_state sii9234_rgnd_ready_irq(struct sii9234 *sii9234)
+{
+	int value;
+	struct device *dev = sii9234_dev(sii9234);
+
+	if (sii9234->state == ST_D3) {
+		int ret;
+
+		dev_dbg(dev, "RGND_READY_INT\n");
+		sii9234_hw_reset(sii9234);
+
+		ret = sii9234_reset(sii9234);
+		if (ret < 0) {
+			dev_err(dev, "sii9234_reset() failed\n");
+			return ST_FAILURE;
+		}
+
+		return ST_RGND_INIT;
+	}
+
+	/* got interrupt in inappropriate state */
+	if (sii9234->state != ST_RGND_INIT)
+		return ST_FAILURE;
+
+	value = mhl_tx_readb(sii9234, MHL_TX_STAT2_REG);
+	if (sii9234_clear_error(sii9234))
+		return ST_FAILURE;
+
+	if ((value & RGND_INTP_MASK) != RGND_INTP_1K) {
+		dev_warn(dev, "RGND is not 1k\n");
+		return ST_RGND_INIT;
+	}
+	dev_dbg(dev, "RGND 1K!!\n");
+	/* After applying RGND patch, there is some issue
+	   about discovry failure
+	   This point is add to fix that problem */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL4_REG, ~0, 0x8C);
+	mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL5_REG, 0x77);
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, ~0, 0x05);
+	if (sii9234_clear_error(sii9234))
+		return ST_FAILURE;
+
+	usleep_range(T_SRC_VBUS_CBUS_TO_STABLE * USEC_PER_MSEC,
+		     T_SRC_VBUS_CBUS_TO_STABLE * USEC_PER_MSEC);
+
+	return ST_RGND_1K;
+}
+
+static enum sii9234_state sii9234_mhl_established(struct sii9234 *sii9234)
+{
+	dev_dbg(sii9234_dev(sii9234), "mhl est interrupt\n");
+
+	/* discovery override */
+	mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL1_REG, 0x10);
+	/* increase DDC translation layer timer (byte mode) */
+	cbus_writeb(sii9234, 0x07, 0x32);
+	cbus_writebm(sii9234, 0x44, ~0, 1 << 1);
+	/* Keep the discovery enabled. Need RGND interrupt */
+	mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, ~0, 1);
+	mhl_tx_writeb(sii9234, MHL_TX_INTR1_ENABLE_REG,
+	       RSEN_CHANGE_INT_MASK | HPD_CHANGE_INT_MASK);
+
+	if (sii9234_clear_error(sii9234))
+		return ST_FAILURE;
+
+	return ST_MHL_ESTABLISHED;
+}
+
+static enum sii9234_state sii9234_hpd_change(struct sii9234 *sii9234)
+{
+	int value;
+
+	value = cbus_readb(sii9234, CBUS_MSC_REQ_ABORT_REASON_REG);
+	if (sii9234_clear_error(sii9234))
+		return ST_FAILURE;
+
+	if (value & SET_HPD_DOWNSTREAM) {
+		dev_info(sii9234_dev(sii9234), "HPD High\n");
+		/* Downstream HPD High, Enable TMDS */
+		sii9234_tmds_control(sii9234, true);
+		/*turn on&off hpd festure for only QCT HDMI */
+	} else {
+		dev_info(sii9234_dev(sii9234), "HPD Low\n");
+		/* Downstream HPD Low, Disable TMDS */
+		sii9234_tmds_control(sii9234, false);
+	}
+
+	return sii9234->state;
+}
+
+static enum sii9234_state sii9234_rsen_change(struct sii9234 *sii9234)
+{
+	int value;
+	struct device *dev = sii9234_dev(sii9234);
+
+	/* work_around code to handle worng interrupt */
+	if (sii9234->state != ST_RGND_1K) {
+		dev_err(dev, "RSEN_HIGH without RGND_1K\n");
+		return ST_FAILURE;
+	}
+	value = mhl_tx_readb(sii9234, MHL_TX_SYSSTAT_REG);
+	if (value < 0)
+		return ST_FAILURE;
+
+	if (value & RSEN_STATUS) {
+		dev_info(dev, "MHL cable connected.. RSEN High\n");
+		return ST_RSEN_HIGH;
+	}
+	dev_info(dev, "RSEN lost\n");
+	/* Once RSEN loss is confirmed,we need to check
+	 * based on cable status and chip power status,whether
+	 * it is SINK Loss(HDMI cable not connected, TV Off)
+	 * or MHL cable disconnection
+	 * TODO: Define the below mhl_disconnection()
+	 */
+	msleep(T_SRC_RXSENSE_DEGLITCH);
+	value = mhl_tx_readb(sii9234, MHL_TX_SYSSTAT_REG);
+	if (value < 0)
+		return ST_FAILURE;
+	dev_dbg(dev, "sys_stat: %x\n", value);
+
+	if (value & RSEN_STATUS) {
+		dev_info(dev, "RSEN recovery\n");
+		return ST_RSEN_HIGH;
+	}
+	dev_info(dev, "RSEN Really LOW\n");
+	/*To meet CTS 3.3.22.2 spec */
+	sii9234_tmds_control(sii9234, false);
+	force_usb_id_switch_open(sii9234);
+	release_usb_id_switch_open(sii9234);
+
+	return ST_FAILURE;
+}
+
+static irqreturn_t sii9234_irq_thread(int irq, void *data)
+{
+	struct sii9234 *sii9234 = data;
+	int intr1, intr4;
+	int intr1_en, intr4_en;
+	int cbus_intr1, cbus_intr2;
+	struct device *dev = sii9234_dev(sii9234);
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	msleep(30);
+
+	mutex_lock(&sii9234->lock);
+
+	intr1 = mhl_tx_readb(sii9234, MHL_TX_INTR1_REG);
+	intr4 = mhl_tx_readb(sii9234, MHL_TX_INTR4_REG);
+	intr1_en = mhl_tx_readb(sii9234, MHL_TX_INTR1_ENABLE_REG);
+	intr4_en = mhl_tx_readb(sii9234, MHL_TX_INTR4_ENABLE_REG);
+	cbus_intr1 = cbus_readb(sii9234, CBUS_INT_STATUS_1_REG);
+	cbus_intr2 = cbus_readb(sii9234, CBUS_INT_STATUS_2_REG);
+
+	if (sii9234_clear_error(sii9234))
+		goto done;
+
+	dev_dbg(dev, "irq %02x/%02x %02x/%02x %02x/%02x\n",
+		 intr1, intr1_en, intr4, intr4_en, cbus_intr1, cbus_intr2);
+
+	if (intr4 & RGND_READY_INT)
+		sii9234->state = sii9234_rgnd_ready_irq(sii9234);
+	if (intr1 & RSEN_CHANGE_INT)
+		sii9234->state = sii9234_rsen_change(sii9234);
+	if (intr4 & MHL_EST_INT)
+		sii9234->state = sii9234_mhl_established(sii9234);
+	if (intr1 & HPD_CHANGE_INT)
+		sii9234->state = sii9234_hpd_change(sii9234);
+	if (intr4 & CBUS_LKOUT_INT)
+		sii9234->state = ST_FAILURE;
+	if (intr4 & MHL_DISC_FAIL_INT)
+		sii9234->state = ST_FAILURE_DISCOVERY;
+
+ done:
+	/* clean interrupt status and pending flags */
+	mhl_tx_writeb(sii9234, MHL_TX_INTR1_REG, intr1);
+	mhl_tx_writeb(sii9234, MHL_TX_INTR4_REG, intr4);
+	cbus_writeb(sii9234, CBUS_MHL_STATUS_REG_0, 0xFF);
+	cbus_writeb(sii9234, CBUS_MHL_STATUS_REG_1, 0xFF);
+	cbus_writeb(sii9234, CBUS_INT_STATUS_1_REG, cbus_intr1);
+	cbus_writeb(sii9234, CBUS_INT_STATUS_2_REG, cbus_intr2);
+
+	sii9234_clear_error(sii9234);
+
+	if (sii9234->state == ST_FAILURE) {
+		dev_info(dev, "try to reset after failure\n");
+		sii9234_hw_reset(sii9234);
+		sii9234_goto_d3(sii9234);
+	}
+
+	if (sii9234->state == ST_FAILURE_DISCOVERY) {
+		dev_err(dev, "discovery failed, no power for MHL?\n");
+		tpi_writebm(sii9234, TPI_DPD_REG, 0, 1);
+		sii9234->state = ST_D3;
+	}
+
+	mutex_unlock(&sii9234->lock);
+
+	return IRQ_HANDLED;
+}
+
+static void sii9234_extcon_work(struct work_struct *work)
+{
+	struct sii9234 *sii9234 =
+		container_of(work, struct sii9234, extcon_wq);
+
+	dev_info(sii9234_dev(sii9234), "MHL is %s\n",
+		sii9234->extcon_attached ? "attached" : "detached");
+
+	if (sii9234->extcon_attached)
+		sii9234_cable_in(sii9234);
+	else
+		sii9234_cable_out(sii9234);
+}
+
+static int sii9234_extcon_notifier(struct notifier_block *self,
+			unsigned long event, void *ptr)
+{
+	struct sii9234 *sii9234 =
+		container_of(self, struct sii9234, extcon_nb);
+
+	sii9234->extcon_attached = event;
+	schedule_work(&sii9234->extcon_wq);
+
+	return NOTIFY_DONE;
+}
+
+static int sii9234_extcon_init(struct sii9234 *sii9234)
+{
+	struct device *dev = &sii9234->client[I2C_MHL]->dev;
+	struct extcon_dev *edev;
+	int ret;
+
+	if (of_property_read_bool(dev->of_node, "extcon")) {
+		edev = extcon_get_edev_by_phandle(dev, 0);
+		if (IS_ERR(edev)) {
+			dev_err(dev, "failed to acquire extcon device\n");
+			return PTR_ERR(edev);
+		}
+
+		sii9234->extcon_attached = extcon_get_cable_state(edev, "MHL");
+		dev_info(dev, "extcon(MHL) = %d\n", sii9234->extcon_attached);
+
+		sii9234->extcon_nb.notifier_call = sii9234_extcon_notifier;
+		ret = extcon_register_interest(&sii9234->extcon_dev, edev->name,
+			"MHL", &sii9234->extcon_nb);
+
+		if (ret) {
+			dev_err(dev, "failed to register notifier for MHL\n");
+			return ret;
+		}
+		INIT_WORK(&sii9234->extcon_wq, sii9234_extcon_work);
+	} else {
+		dev_info(dev, "no extcon found, switching to 'always on' mode\n");
+		sii9234->extcon_attached = true;
+	}
+	return 0;
+}
+
+static int sii9234_init_resources(struct sii9234 *sii9234,
+	struct i2c_client *client)
+{
+	struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+	struct device *dev = &client->dev;
+	int ret;
+
+	if (!dev->of_node) {
+		dev_err(dev, "not DT device\n");
+		return -ENODEV;
+	}
+
+	sii9234->gpio_n_reset = of_get_named_gpio(dev->of_node,
+		"gpio-reset", 0);
+	if (!gpio_is_valid(sii9234->gpio_n_reset)) {
+		dev_err(dev, "failed to get gpio-reset from DT\n");
+		return -ENODEV;
+	}
+	sii9234->gpio_int = of_get_named_gpio(dev->of_node, "gpio-int", 0);
+	if (!gpio_is_valid(sii9234->gpio_int)) {
+		dev_err(dev, "failed to get gpio-int from DT\n");
+		return -ENODEV;
+	}
+
+	ret = devm_gpio_request(dev, sii9234->gpio_n_reset, "MHL_RST");
+	if (ret) {
+		dev_err(dev, "failed to acquire MHL_RST gpio\n");
+		return ret;
+	}
+
+	ret = devm_gpio_request(dev, sii9234->gpio_int, "MHL_INT");
+	if (ret) {
+		dev_err(dev, "failed to request MHL_INT gpio\n");
+		return ret;
+	}
+
+	sii9234->vcc_supply = devm_regulator_get(dev, "vcc");
+	if (IS_ERR(sii9234->vcc_supply)) {
+		dev_err(dev, "failed to acquire regulator vcc\n");
+		return PTR_ERR(sii9234->vcc_supply);
+	}
+
+	sii9234->client[I2C_MHL] = client;
+
+	sii9234->client[I2C_TPI] = i2c_new_dummy(adapter, 0x7A >> 1);
+	if (!sii9234->client[I2C_TPI]) {
+		dev_err(dev, "failed to create TPI client\n");
+		return -ENODEV;
+	}
+
+	sii9234->client[I2C_HDMI] = i2c_new_dummy(adapter, 0x92 >> 1);
+	if (!sii9234->client[I2C_HDMI]) {
+		dev_err(dev, "failed to create HDMI RX client\n");
+		goto fail_tpi;
+	}
+
+	sii9234->client[I2C_CBUS] = i2c_new_dummy(adapter, 0xC8 >> 1);
+	if (!sii9234->client[I2C_CBUS]) {
+		dev_err(dev, "failed to create CBUS client\n");
+		goto fail_hdmi;
+	}
+
+	return 0;
+
+fail_hdmi:
+	i2c_unregister_device(sii9234->client[I2C_HDMI]);
+fail_tpi:
+	i2c_unregister_device(sii9234->client[I2C_TPI]);
+
+	return -ENODEV;
+}
+
+static void sii9234_deinit_resources(struct sii9234 *sii9234)
+{
+	i2c_unregister_device(sii9234->client[I2C_CBUS]);
+	i2c_unregister_device(sii9234->client[I2C_HDMI]);
+	i2c_unregister_device(sii9234->client[I2C_TPI]);
+}
+
+static int sii9234_mhl_tx_i2c_probe(struct i2c_client *client,
+					      const struct i2c_device_id *id)
+{
+	struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+	struct sii9234 *sii9234;
+	struct device *dev = &client->dev;
+	int ret;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+		dev_err(dev, "I2C adapter lacks SMBUS feature\n");
+		return -EIO;
+	}
+
+	sii9234 = devm_kzalloc(dev, sizeof(struct sii9234), GFP_KERNEL);
+	if (!sii9234) {
+		dev_err(dev, "not enough memory\n");
+		return -ENOMEM;
+	}
+
+	mutex_init(&sii9234->lock);
+
+	ret = sii9234_init_resources(sii9234, client);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to initialize sii9234 resources\n");
+		return ret;
+	}
+	ret = sii9234_hw_on(sii9234);
+	if (ret) {
+		dev_err(&client->dev, "failed to enable power\n");
+		goto err_resource;
+	}
+	sii9234_hw_reset(sii9234);
+
+	i2c_set_clientdata(client, sii9234);
+
+	sii9234->irq = gpio_to_irq(sii9234->gpio_int);
+	ret = devm_request_threaded_irq(dev, sii9234->irq, NULL,
+		sii9234_irq_thread, IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+		"sii9234", sii9234);
+	if (ret < 0) {
+		dev_err(dev, "failed to request MHL interrupt\n");
+		goto err_hw_power;
+	}
+
+	disable_irq(sii9234->irq);
+
+	ret = sii9234_extcon_init(sii9234);
+	if (ret < 0) {
+		dev_err(dev, "failed to initialize EXTCON\n");
+		goto err_hw_power;
+	}
+
+	/* Force MHL connect EVENT for platforms with no EXTCON */
+	if (sii9234->extcon_attached)
+		sii9234_cable_in(sii9234);
+
+	return 0;
+
+err_hw_power:
+	sii9234_hw_off(sii9234);
+
+err_resource:
+	sii9234_deinit_resources(sii9234);
+
+	return ret;
+}
+
+static int sii9234_mhl_tx_i2c_remove(struct i2c_client *client)
+{
+	struct sii9234 *sii9234 = i2c_get_clientdata(client);
+
+	extcon_unregister_interest(&sii9234->extcon_dev);
+	if (sii9234->extcon_attached)
+		sii9234_cable_out(sii9234);
+	sii9234_deinit_resources(sii9234);
+
+	return 0;
+}
+
+static const struct of_device_id sii9234_dt_match[] = {
+	{ .compatible = "sil,sii9234" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, sii9234_dt_match);
+
+static const struct i2c_device_id sii9234_id[] = {
+	{ "SII9234", 0 },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(i2c, sii9234_id);
+static struct i2c_driver sii9234_driver = {
+	.driver = {
+		.name	= "sii9234",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(sii9234_dt_match),
+	},
+	.probe		= sii9234_mhl_tx_i2c_probe,
+	.remove		= sii9234_mhl_tx_i2c_remove,
+	.id_table = sii9234_id,
+};
+
+module_i2c_driver(sii9234_driver);
+MODULE_LICENSE("GPL");
