@@ -83,6 +83,22 @@ sti-hda:
- clock-names: names of the clocks listed in clocks property in the same
order.
+sti-dvo:
+ Required properties:
+ must be a child of sti-tvout
+ - compatible: "st,stih<chip>-dvo"
+ - reg: Physical base address of the IP registers and length of memory mapped region.
+ - reg-names: names of the mapped memory regions listed in regs property in
+ the same order.
+ - clocks: from common clock binding: handle hardware IP needed clocks, the
+ number of clocks may depend of the SoC type.
+ See ../clocks/clock-bindings.txt for details.
+ - clock-names: names of the clocks listed in clocks property in the same
+ order.
+ - pinctrl-0: pin control handle
+ - pinctrl-name: names of the pin control to use
+ - sti,panel: phandle of the panel connected to the DVO output
+
sti-hqvdp:
must be a child of sti-display-subsystem
Required properties:
@@ -198,6 +214,19 @@ Example:
clock-names = "pix", "hddac";
clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>;
};
+
+ sti-dvo@8d00400 {
+ compatible = "st,stih407-dvo";
+ reg = <0x8d00400 0x200>;
+ reg-names = "dvo-reg";
+ clock-names = "dvo_pix", "dvo",
+ "main_parent", "aux_parent";
+ clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>, <&clk_s_d2_flexgen CLK_DVO>,
+ <&clk_s_d2_quadfs 0>, <&clk_s_d2_quadfs 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dvo>;
+ sti,panel = <&panel_dvo>;
+ };
};
sti-hqvdp@9c000000 {
@@ -12,6 +12,9 @@ stihdmi-y := sti_hdmi.o \
sti_hdmi_tx3g0c55phy.o \
sti_hdmi_tx3g4c28phy.o \
+stidvo-y := sti_dvo.o \
+ sti_awg_utils.o
+
obj-$(CONFIG_DRM_STI) = \
sti_vtg.o \
sti_vtac.o \
@@ -20,4 +23,5 @@ obj-$(CONFIG_DRM_STI) = \
sti_tvout.o \
sticompositor.o \
sti_hqvdp.o \
+ stidvo.o \
sti_drm_drv.o
new file mode 100644
@@ -0,0 +1,184 @@
+/*
+ * Copyright (C) STMicroelectronics SA 2014
+ * Author: Vincent Abriou <vincent.abriou@st.com> for STMicroelectronics.
+ * License terms: GNU General Public License (GPL), version 2
+ */
+
+#include "sti_awg_utils.h"
+
+#define AWG_OPCODE_OFFSET 10
+
+enum opcode {
+ SET,
+ RPTSET,
+ RPLSET,
+ SKIP,
+ STOP,
+ REPEAT,
+ REPLAY,
+ JUMP,
+ HOLD,
+};
+
+static int awg_generate_instr(enum opcode opcode,
+ long int arg,
+ long int mux_sel,
+ long int data_en,
+ struct awg_code_generation_params *fwparams)
+{
+ u32 instruction = 0;
+ u32 mux = (mux_sel << 8) & 0x1ff;
+ u32 data_enable = (data_en << 9) & 0x2ff;
+ long int arg_tmp = arg;
+
+ /* skip, repeat and replay arg should not exceed 1023.
+ * If user wants to exceed this value, the instruction should be
+ * duplicate and arg should be adjust for each duplicated instruction.
+ */
+
+ while (arg_tmp > 0) {
+ arg = arg_tmp;
+ if (fwparams->instruction_offset >= AWG_MAX_INST) {
+ DRM_ERROR("too many number of instructions\n");
+ return -EINVAL;
+ }
+
+ switch (opcode) {
+ case SKIP:
+ /* leave 'arg' + 1 pixel elapsing without changing
+ * output bus */
+ arg--; /* pixel adjustment */
+ arg_tmp--;
+
+ if (arg < 0) {
+ /* SKIP instruction not needed */
+ return 0;
+ }
+
+ if (arg == 0) {
+ /* SKIP 0 not permitted but we want to skip 1
+ * pixel. So we transform SKIP into SET
+ * instruction */
+ opcode = SET;
+ arg = (arg << 24) >> 24;
+ arg &= (0x0ff);
+ break;
+ }
+
+ mux = 0;
+ data_enable = 0;
+ arg = (arg << 22) >> 22;
+ arg &= (0x3ff);
+ break;
+ case REPEAT:
+ case REPLAY:
+ if (arg == 0) {
+ /* REPEAT or REPLAY instruction not needed */
+ return 0;
+ }
+
+ mux = 0;
+ data_enable = 0;
+ arg = (arg << 22) >> 22;
+ arg &= (0x3ff);
+ break;
+ case JUMP:
+ mux = 0;
+ data_enable = 0;
+ arg |= 0x40; /* for jump instruction 7th bit is 1 */
+ arg = (arg << 22) >> 22;
+ arg &= 0x3ff;
+ break;
+ case STOP:
+ arg = 0;
+ break;
+ case SET:
+ case RPTSET:
+ case RPLSET:
+ case HOLD:
+ arg = (arg << 24) >> 24;
+ arg &= (0x0ff);
+ break;
+ default:
+ DRM_ERROR("instruction %d does not exist\n", opcode);
+ return -EINVAL;
+ }
+
+ arg_tmp = arg_tmp - arg;
+
+ arg = ((arg + mux) + data_enable);
+
+ instruction = ((opcode) << AWG_OPCODE_OFFSET) | arg;
+ fwparams->ram_code[fwparams->instruction_offset] =
+ instruction & (0x3fff);
+ fwparams->instruction_offset++;
+ }
+ return 0;
+}
+
+int sti_awg_generate_code_data_enable_mode(
+ struct awg_code_generation_params *fwparams,
+ struct awg_timing *timing)
+{
+ long int val;
+ long int data_en;
+ int ret = 0;
+
+ if (timing->trailing_lines > 0) {
+ /* skip trailing lines */
+ val = timing->blanking_level;
+ data_en = 0;
+ ret |= awg_generate_instr(RPLSET, val, 0, data_en, fwparams);
+
+ val = timing->trailing_lines - 1;
+ data_en = 0;
+ ret |= awg_generate_instr(REPLAY, val, 0, data_en, fwparams);
+ }
+
+ if (timing->trailing_pixels > 0) {
+ /* skip trailing pixel */
+ val = timing->blanking_level;
+ data_en = 0;
+ ret |= awg_generate_instr(RPLSET, val, 0, data_en, fwparams);
+
+ val = timing->trailing_pixels - 1;
+ data_en = 0;
+ ret |= awg_generate_instr(SKIP, val, 0, data_en, fwparams);
+ }
+
+ /* set DE signal high */
+ val = timing->blanking_level;
+ data_en = 1;
+ ret |= awg_generate_instr((timing->trailing_pixels > 0) ? SET : RPLSET,
+ val, 0, data_en, fwparams);
+
+ if (timing->blanking_pixels > 0) {
+ /* skip the number of active pixel */
+ val = timing->active_pixels - 1;
+ data_en = 1;
+ ret |= awg_generate_instr(SKIP, val, 0, data_en, fwparams);
+
+ /* set DE signal low */
+ val = timing->blanking_level;
+ data_en = 0;
+ ret |= awg_generate_instr(SET, val, 0, data_en, fwparams);
+ }
+
+ /* replay the sequence as many active lines defined */
+ val = timing->active_lines - 1;
+ data_en = 0;
+ ret |= awg_generate_instr(REPLAY, val, 0, data_en, fwparams);
+
+ if (timing->blanking_lines > 0) {
+ /* skip blanking lines */
+ val = timing->blanking_level;
+ data_en = 0;
+ ret |= awg_generate_instr(RPLSET, val, 0, data_en, fwparams);
+
+ val = timing->blanking_lines - 1;
+ data_en = 0;
+ ret |= awg_generate_instr(REPLAY, val, 0, data_en, fwparams);
+ }
+
+ return ret;
+}
new file mode 100644
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) STMicroelectronics SA 2014
+ * Author: Vincent Abriou <vincent.abriou@st.com> for STMicroelectronics.
+ * License terms: GNU General Public License (GPL), version 2
+ */
+
+#ifndef _STI_AWG_UTILS_H_
+#define _STI_AWG_UTILS_H_
+
+#include <drm/drmP.h>
+
+#define AWG_MAX_INST 64
+
+struct awg_code_generation_params {
+ u32 *ram_code;
+ u8 instruction_offset;
+};
+
+struct awg_timing {
+ u32 total_lines;
+ u32 active_lines;
+ u32 blanking_lines;
+ u32 trailing_lines;
+ u32 total_pixels;
+ u32 active_pixels;
+ u32 blanking_pixels;
+ u32 trailing_pixels;
+ u32 blanking_level;
+};
+
+int sti_awg_generate_code_data_enable_mode(
+ struct awg_code_generation_params *fw_gen_params,
+ struct awg_timing *timing);
+#endif
new file mode 100644
@@ -0,0 +1,551 @@
+/*
+ * Copyright (C) STMicroelectronics SA 2014
+ * Author: Vincent Abriou <vincent.abriou@st.com> for STMicroelectronics.
+ * License terms: GNU General Public License (GPL), version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_panel.h>
+
+#include "sti_awg_utils.h"
+#include "sti_mixer.h"
+
+/* DVO registers */
+#define DVO_AWG_DIGSYNC_CTRL 0x0000
+#define DVO_DOF_CFG 0x0004
+#define DVO_LUT_PROG_LOW 0x0008
+#define DVO_LUT_PROG_MID 0x000C
+#define DVO_LUT_PROG_HIGH 0x0010
+#define DVO_DIGSYNC_INSTR_I 0x0100
+
+#define DVO_AWG_CTRL_EN BIT(0)
+#define DVO_AWG_FRAME_BASED_SYNC BIT(2)
+
+#define DVO_DOF_EN_LOWBYTE BIT(0)
+#define DVO_DOF_EN_MIDBYTE BIT(1)
+#define DVO_DOF_EN_HIGHBYTE BIT(2)
+#define DVO_DOF_EN BIT(6)
+#define DVO_DOF_MOD_COUNT_SHIFT 8
+
+#define DVO_LUT_ZERO 0
+#define DVO_LUT_Y_G 1
+#define DVO_LUT_Y_G_DEL 2
+#define DVO_LUT_CB_B 3
+#define DVO_LUT_CB_B_DEL 4
+#define DVO_LUT_CR_R 5
+#define DVO_LUT_CR_R_DEL 6
+#define DVO_LUT_HOLD 7
+
+struct dvo_config {
+ u32 flags;
+ u32 lowbyte;
+ u32 midbyte;
+ u32 highbyte;
+ int (*awg_fwgen_fct)(
+ struct awg_code_generation_params *fw_gen_params,
+ struct awg_timing *timing);
+};
+
+static struct dvo_config rgb_24bit_de_cfg = {
+ .flags = (0L << DVO_DOF_MOD_COUNT_SHIFT),
+ .lowbyte = DVO_LUT_CR_R,
+ .midbyte = DVO_LUT_Y_G,
+ .highbyte = DVO_LUT_CB_B,
+ .awg_fwgen_fct = sti_awg_generate_code_data_enable_mode,
+};
+
+/**
+ * STI digital video output structure
+ *
+ * @dev: driver device
+ * @drm_dev: pointer to drm device
+ * @mode: current display mode selected
+ * @regs: dvo registers
+ * @clk_pix: pixel clock for dvo
+ * @clk: clock for dvo
+ * @clk_main_parent: dvo parent clock if main path used
+ * @clk_aux_parent: dvo parent clock if aux path used
+ * @panel_node: panel node reference from device tree
+ * @panel: reference to the panel connected to the dvo
+ * @enabled: true if dvo is enabled else false
+ * @encoder: drm_encoder it is bound
+ */
+struct sti_dvo {
+ struct device dev;
+ struct drm_device *drm_dev;
+ struct drm_display_mode mode;
+ void __iomem *regs;
+ struct clk *clk_pix;
+ struct clk *clk;
+ struct clk *clk_main_parent;
+ struct clk *clk_aux_parent;
+ struct device_node *panel_node;
+ struct drm_panel *panel;
+ struct dvo_config *config;
+ bool enabled;
+ struct drm_encoder *encoder;
+};
+
+struct sti_dvo_connector {
+ struct drm_connector drm_connector;
+ struct drm_encoder *encoder;
+ struct sti_dvo *dvo;
+};
+
+#define to_sti_dvo_connector(x) \
+ container_of(x, struct sti_dvo_connector, drm_connector)
+
+#define BLANKING_LEVEL 16
+int dvo_awg_generate_code(struct sti_dvo *dvo, u8 *ram_size, u32 *ram_code)
+{
+ struct drm_display_mode *mode = &dvo->mode;
+ struct dvo_config *config = dvo->config;
+ struct awg_code_generation_params fw_gen_params;
+ struct awg_timing timing;
+
+ fw_gen_params.ram_code = ram_code;
+ fw_gen_params.instruction_offset = 0;
+
+ timing.total_lines = mode->vtotal;
+ timing.active_lines = mode->vdisplay;
+ timing.blanking_lines = mode->vsync_start - mode->vdisplay;
+ timing.trailing_lines = mode->vtotal - mode->vsync_start;
+ timing.total_pixels = mode->htotal;
+ timing.active_pixels = mode->hdisplay;
+ timing.blanking_pixels = mode->hsync_start - mode->hdisplay;
+ timing.trailing_pixels = mode->htotal - mode->hsync_start;
+ timing.blanking_level = BLANKING_LEVEL;
+
+ if (config->awg_fwgen_fct(&fw_gen_params, &timing)) {
+ DRM_ERROR("AWG firmware not properly generated\n");
+ return -EINVAL;
+ }
+
+ *ram_size = fw_gen_params.instruction_offset;
+
+ return 0;
+}
+
+/* Configure AWG, writing instructions
+ *
+ * @dvo: pointer to DVO structure
+ * @awg_ram_code: pointer to AWG instructions table
+ * @nb: nb of AWG instructions
+ */
+static void dvo_awg_configure(struct sti_dvo *dvo, u32 *awg_ram_code, int nb)
+{
+ int i;
+
+ DRM_DEBUG_DRIVER("\n");
+
+ for (i = 0; i < nb; i++)
+ writel(awg_ram_code[i],
+ dvo->regs + DVO_DIGSYNC_INSTR_I + i * 4);
+ for (i = nb; i < AWG_MAX_INST; i++)
+ writel(0, dvo->regs + DVO_DIGSYNC_INSTR_I + i * 4);
+
+ writel(DVO_AWG_CTRL_EN, dvo->regs + DVO_AWG_DIGSYNC_CTRL);
+}
+
+static void sti_dvo_disable(struct drm_bridge *bridge)
+{
+ struct sti_dvo *dvo = bridge->driver_private;
+
+ if (!dvo->enabled)
+ return;
+
+ DRM_DEBUG_DRIVER("\n");
+
+ if (dvo->config->awg_fwgen_fct)
+ writel(0x00000000, dvo->regs + DVO_AWG_DIGSYNC_CTRL);
+
+ writel(0x00000000, dvo->regs + DVO_DOF_CFG);
+
+ if (dvo->panel)
+ dvo->panel->funcs->disable(dvo->panel);
+
+ /* Disable/unprepare dvo clock */
+ clk_disable_unprepare(dvo->clk_pix);
+ clk_disable_unprepare(dvo->clk);
+
+ dvo->enabled = false;
+}
+
+static void sti_dvo_pre_enable(struct drm_bridge *bridge)
+{
+ struct sti_dvo *dvo = bridge->driver_private;
+ struct dvo_config *config = dvo->config;
+ u32 val;
+
+ DRM_DEBUG_DRIVER("\n");
+
+ if (dvo->enabled)
+ return;
+
+ /* Make sure DVO is disabled */
+ writel(0x00000000, dvo->regs + DVO_DOF_CFG);
+ writel(0x00000000, dvo->regs + DVO_AWG_DIGSYNC_CTRL);
+
+ if (config->awg_fwgen_fct) {
+ u8 nb_instr;
+ u32 awg_ram_code[AWG_MAX_INST];
+ /* Configure AWG */
+ if (!dvo_awg_generate_code(dvo, &nb_instr, awg_ram_code))
+ dvo_awg_configure(dvo, awg_ram_code, nb_instr);
+ else
+ return;
+ }
+
+ /* Prepare/enable clocks */
+ if (clk_prepare_enable(dvo->clk_pix))
+ DRM_ERROR("Failed to prepare/enable dvo_pix clk\n");
+ if (clk_prepare_enable(dvo->clk))
+ DRM_ERROR("Failed to prepare/enable dvo clk\n");
+
+ if (dvo->panel)
+ dvo->panel->funcs->enable(dvo->panel);
+
+ /* Set LUT */
+ writel(config->lowbyte, dvo->regs + DVO_LUT_PROG_LOW);
+ writel(config->midbyte, dvo->regs + DVO_LUT_PROG_MID);
+ writel(config->highbyte, dvo->regs + DVO_LUT_PROG_HIGH);
+
+ /* Digital output formatter config */
+ val = (config->flags | DVO_DOF_EN);
+ writel(val, dvo->regs + DVO_DOF_CFG);
+
+ dvo->enabled = true;
+}
+
+static void sti_dvo_set_mode(struct drm_bridge *bridge,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct sti_dvo *dvo = bridge->driver_private;
+ struct sti_mixer *mixer = to_sti_mixer(dvo->encoder->crtc);
+ int rate = mode->clock * 1000;
+ struct clk *clkp;
+ int ret;
+
+ DRM_DEBUG_DRIVER("\n");
+
+ memcpy(&dvo->mode, mode, sizeof(struct drm_display_mode));
+
+ /* According to the path used (main or aux), the dvo clocks should
+ * have a different parent clock. */
+ if (mixer->id == STI_MIXER_MAIN)
+ clkp = dvo->clk_main_parent;
+ else
+ clkp = dvo->clk_aux_parent;
+
+ if (clkp) {
+ clk_set_parent(dvo->clk_pix, clkp);
+ clk_set_parent(dvo->clk, clkp);
+ }
+
+ /* DVO clocks = compositor clock */
+ ret = clk_set_rate(dvo->clk_pix, rate);
+ if (ret < 0) {
+ DRM_ERROR("Cannot set rate (%dHz) for dvo_pix clk\n", rate);
+ return;
+ }
+
+ ret = clk_set_rate(dvo->clk, rate);
+ if (ret < 0) {
+ DRM_ERROR("Cannot set rate (%dHz) for dvo clk\n", rate);
+ return;
+ }
+
+ /* For now, we only support 24bit data enable (DE) synchro format */
+ dvo->config = &rgb_24bit_de_cfg;
+}
+
+static void sti_dvo_bridge_nope(struct drm_bridge *bridge)
+{
+ /* do nothing */
+}
+
+static void sti_dvo_brigde_destroy(struct drm_bridge *bridge)
+{
+ drm_bridge_cleanup(bridge);
+ kfree(bridge);
+}
+
+static const struct drm_bridge_funcs sti_dvo_bridge_funcs = {
+ .pre_enable = sti_dvo_pre_enable,
+ .enable = sti_dvo_bridge_nope,
+ .disable = sti_dvo_disable,
+ .post_disable = sti_dvo_bridge_nope,
+ .mode_set = sti_dvo_set_mode,
+ .destroy = sti_dvo_brigde_destroy,
+};
+
+static int sti_dvo_connector_get_modes(struct drm_connector *connector)
+{
+ struct sti_dvo_connector *dvo_connector
+ = to_sti_dvo_connector(connector);
+ struct sti_dvo *dvo = dvo_connector->dvo;
+
+ if (dvo->panel)
+ return dvo->panel->funcs->get_modes(dvo->panel);
+
+ return 0;
+}
+
+#define CLK_TOLERANCE_HZ 50
+
+static int sti_dvo_connector_mode_valid(struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ int target = mode->clock * 1000;
+ int target_min = target - CLK_TOLERANCE_HZ;
+ int target_max = target + CLK_TOLERANCE_HZ;
+ int result;
+ struct sti_dvo_connector *dvo_connector
+ = to_sti_dvo_connector(connector);
+ struct sti_dvo *dvo = dvo_connector->dvo;
+
+ result = clk_round_rate(dvo->clk_pix, target);
+
+ DRM_DEBUG_DRIVER("target rate = %d => available rate = %d\n",
+ target, result);
+
+ if ((result < target_min) || (result > target_max)) {
+ DRM_DEBUG_DRIVER("dvo pixclk=%d not supported\n", target);
+ return MODE_BAD;
+ }
+
+ return MODE_OK;
+}
+
+struct drm_encoder *sti_dvo_best_encoder(struct drm_connector *connector)
+{
+ struct sti_dvo_connector *dvo_connector
+ = to_sti_dvo_connector(connector);
+
+ /* Best encoder is the one associated during connector creation */
+ return dvo_connector->encoder;
+}
+
+static struct drm_connector_helper_funcs sti_dvo_connector_helper_funcs = {
+ .get_modes = sti_dvo_connector_get_modes,
+ .mode_valid = sti_dvo_connector_mode_valid,
+ .best_encoder = sti_dvo_best_encoder,
+};
+
+static enum drm_connector_status
+sti_dvo_connector_detect(struct drm_connector *connector, bool force)
+{
+ struct sti_dvo_connector *dvo_connector
+ = to_sti_dvo_connector(connector);
+ struct sti_dvo *dvo = dvo_connector->dvo;
+
+ DRM_DEBUG_DRIVER("\n");
+
+ if (!dvo->panel)
+ dvo->panel = of_drm_find_panel(dvo->panel_node);
+
+ if (dvo->panel)
+ if (!drm_panel_attach(dvo->panel, connector))
+ return connector_status_connected;
+
+ return connector_status_disconnected;
+}
+
+static void sti_dvo_connector_destroy(struct drm_connector *connector)
+{
+ struct sti_dvo_connector *dvo_connector
+ = to_sti_dvo_connector(connector);
+
+ drm_connector_unregister(connector);
+ drm_connector_cleanup(connector);
+ kfree(dvo_connector);
+}
+
+static struct drm_connector_funcs sti_dvo_connector_funcs = {
+ .dpms = drm_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = sti_dvo_connector_detect,
+ .destroy = sti_dvo_connector_destroy,
+};
+
+static struct drm_encoder *sti_dvo_find_encoder(struct drm_device *dev)
+{
+ struct drm_encoder *encoder;
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
+ if (encoder->encoder_type == DRM_MODE_ENCODER_LVDS)
+ return encoder;
+ }
+
+ return NULL;
+}
+
+static int sti_dvo_bind(struct device *dev, struct device *master, void *data)
+{
+ struct sti_dvo *dvo = dev_get_drvdata(dev);
+ struct drm_device *drm_dev = data;
+ struct drm_encoder *encoder;
+ struct sti_dvo_connector *connector;
+ struct drm_connector *drm_connector;
+ struct drm_bridge *bridge;
+ int err;
+
+ /* Set the drm device handle */
+ dvo->drm_dev = drm_dev;
+
+ encoder = sti_dvo_find_encoder(drm_dev);
+ if (!encoder)
+ return -ENOMEM;
+
+ connector = devm_kzalloc(dev, sizeof(*connector), GFP_KERNEL);
+ if (!connector)
+ return -ENOMEM;
+
+ connector->dvo = dvo;
+
+ bridge = devm_kzalloc(dev, sizeof(*bridge), GFP_KERNEL);
+ if (!bridge)
+ return -ENOMEM;
+
+ bridge->driver_private = dvo;
+ drm_bridge_init(drm_dev, bridge, &sti_dvo_bridge_funcs);
+
+ encoder->bridge = bridge;
+ connector->encoder = encoder;
+ dvo->encoder = encoder;
+
+ drm_connector = (struct drm_connector *)connector;
+
+ drm_connector->polled = DRM_CONNECTOR_POLL_HPD;
+
+ drm_connector_init(drm_dev, drm_connector,
+ &sti_dvo_connector_funcs, DRM_MODE_CONNECTOR_LVDS);
+ drm_connector_helper_add(drm_connector,
+ &sti_dvo_connector_helper_funcs);
+
+ err = drm_connector_register(drm_connector);
+ if (err)
+ goto err_connector;
+
+ err = drm_mode_connector_attach_encoder(drm_connector, encoder);
+ if (err) {
+ DRM_ERROR("Failed to attach a connector to a encoder\n");
+ goto err_sysfs;
+ }
+
+ return 0;
+
+err_sysfs:
+ drm_connector_unregister(drm_connector);
+err_connector:
+ drm_bridge_cleanup(bridge);
+ drm_connector_cleanup(drm_connector);
+ return -EINVAL;
+}
+
+static void sti_dvo_unbind(struct device *dev,
+ struct device *master, void *data)
+{
+ /* do nothing */
+}
+
+static const struct component_ops sti_dvo_ops = {
+ .bind = sti_dvo_bind,
+ .unbind = sti_dvo_unbind,
+};
+
+static int sti_dvo_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sti_dvo *dvo;
+ struct resource *res;
+ struct device_node *np = dev->of_node;
+
+ DRM_INFO("%s\n", __func__);
+
+ dvo = devm_kzalloc(dev, sizeof(*dvo), GFP_KERNEL);
+ if (!dvo) {
+ DRM_ERROR("Failed to allocate memory for DVO\n");
+ return -ENOMEM;
+ }
+
+ dvo->dev = pdev->dev;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dvo-reg");
+ if (!res) {
+ DRM_ERROR("Invalid dvo resource\n");
+ return -ENOMEM;
+ }
+ dvo->regs = devm_ioremap_nocache(dev, res->start,
+ resource_size(res));
+ if (IS_ERR(dvo->regs))
+ return PTR_ERR(dvo->regs);
+
+ dvo->clk_pix = devm_clk_get(dev, "dvo_pix");
+ if (IS_ERR(dvo->clk_pix)) {
+ DRM_ERROR("Cannot get dvo_pix clock\n");
+ return PTR_ERR(dvo->clk_pix);
+ }
+
+ dvo->clk = devm_clk_get(dev, "dvo");
+ if (IS_ERR(dvo->clk)) {
+ DRM_ERROR("Cannot get dvo clock\n");
+ return PTR_ERR(dvo->clk);
+ }
+
+ dvo->clk_main_parent = devm_clk_get(dev, "main_parent");
+ if (IS_ERR(dvo->clk_main_parent)) {
+ DRM_DEBUG_DRIVER("Cannot get main_parent clock\n");
+ dvo->clk_main_parent = NULL;
+ }
+
+ dvo->clk_aux_parent = devm_clk_get(dev, "aux_parent");
+ if (IS_ERR(dvo->clk_aux_parent)) {
+ DRM_DEBUG_DRIVER("Cannot get aux_parent clock\n");
+ dvo->clk_aux_parent = NULL;
+ }
+
+ dvo->panel_node = of_parse_phandle(np, "sti,panel", 0);
+ if (!dvo->panel_node)
+ DRM_ERROR("No panel associated to the dvo output\n");
+
+ platform_set_drvdata(pdev, dvo);
+
+ return component_add(&pdev->dev, &sti_dvo_ops);
+}
+
+static int sti_dvo_remove(struct platform_device *pdev)
+{
+ component_del(&pdev->dev, &sti_dvo_ops);
+ return 0;
+}
+
+static struct of_device_id dvo_of_match[] = {
+ { .compatible = "st,stih407-dvo", },
+ { /* end node */ }
+};
+MODULE_DEVICE_TABLE(of, dvo_of_match);
+
+struct platform_driver sti_dvo_driver = {
+ .driver = {
+ .name = "sti-dvo",
+ .owner = THIS_MODULE,
+ .of_match_table = dvo_of_match,
+ },
+ .probe = sti_dvo_probe,
+ .remove = sti_dvo_remove,
+};
+
+module_platform_driver(sti_dvo_driver);
+
+MODULE_AUTHOR("Benjamin Gaignard <benjamin.gaignard@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics SoC DRM driver");
+MODULE_LICENSE("GPL");
@@ -48,6 +48,9 @@
#define TVO_HDMI_CLIP_VALUE_R_CR 0x514
#define TVO_HDMI_SYNC_SEL 0x518
#define TVO_HDMI_DFV_OBS 0x540
+#define TVO_VIP_DVO 0x600
+#define TVO_DVO_SYNC_SEL 0x618
+#define TVO_DVO_CONFIG 0x620
#define TVO_IN_FMT_SIGNED BIT(0)
#define TVO_SYNC_EXT BIT(4)
@@ -98,6 +101,9 @@
#define TVO_SYNC_HD_DCS_SHIFT 8
+#define TVO_SYNC_DVO_PAD_HSYNC_SHIFT 8
+#define TVO_SYNC_DVO_PAD_VSYNC_SHIFT 16
+
#define ENCODER_CRTC_MASK (BIT(0) | BIT(1))
/* enum listing the supported output data format */
@@ -113,6 +119,7 @@ struct sti_tvout {
struct reset_control *reset;
struct drm_encoder *hdmi;
struct drm_encoder *hda;
+ struct drm_encoder *dvo;
};
struct sti_tvout_encoder {
@@ -262,6 +269,66 @@ static void tvout_vip_set_in_vid_fmt(struct sti_tvout *tvout,
}
/**
+ * Start VIP block for DVO output
+ *
+ * @tvout: pointer on tvout structure
+ * @main_path: true if main path has to be used in the vip configuration
+ * else aux path is used.
+ */
+static void tvout_dvo_start(struct sti_tvout *tvout, bool main_path)
+{
+ struct device_node *node = tvout->dev->of_node;
+ bool sel_input_logic_inverted = false;
+ u32 tvo_in_vid_format;
+ int val;
+
+ dev_dbg(tvout->dev, "%s\n", __func__);
+
+ if (main_path) {
+ DRM_DEBUG_DRIVER("main vip for DVO\n");
+ /* Select the input sync for dvo = VTG set 4 */
+ val = TVO_SYNC_MAIN_VTG_SET_4 << TVO_SYNC_DVO_PAD_VSYNC_SHIFT;
+ val |= TVO_SYNC_MAIN_VTG_SET_4 << TVO_SYNC_DVO_PAD_HSYNC_SHIFT;
+ val |= TVO_SYNC_MAIN_VTG_SET_4;
+ tvout_write(tvout, val, TVO_DVO_SYNC_SEL);
+ tvo_in_vid_format = TVO_MAIN_IN_VID_FORMAT;
+ } else {
+ DRM_DEBUG_DRIVER("aux vip for DVO\n");
+ /* Select the input sync for dvo = VTG set 4 */
+ val = TVO_SYNC_AUX_VTG_SET_4 << TVO_SYNC_DVO_PAD_VSYNC_SHIFT;
+ val |= TVO_SYNC_AUX_VTG_SET_4 << TVO_SYNC_DVO_PAD_HSYNC_SHIFT;
+ val |= TVO_SYNC_AUX_VTG_SET_4;
+ tvout_write(tvout, val, TVO_DVO_SYNC_SEL);
+ tvo_in_vid_format = TVO_AUX_IN_VID_FORMAT;
+ }
+
+ /* Set color channel order */
+ tvout_vip_set_color_order(tvout, TVO_VIP_DVO,
+ TVO_VIP_REORDER_CR_R_SEL,
+ TVO_VIP_REORDER_Y_G_SEL,
+ TVO_VIP_REORDER_CB_B_SEL);
+
+ /* Set clipping mode (Limited range RGB/Y) */
+ tvout_vip_set_clip_mode(tvout, TVO_VIP_DVO,
+ TVO_VIP_CLIP_LIMITED_RANGE_RGB_Y);
+
+ /* Set round mode (rounded to 8-bit per component) */
+ tvout_vip_set_rnd(tvout, TVO_VIP_DVO, TVO_VIP_RND_8BIT_ROUNDED);
+
+ if (of_device_is_compatible(node, "st,stih407-tvout")) {
+ /* Set input video format */
+ tvout_vip_set_in_vid_fmt(tvout, tvo_in_vid_format,
+ TVO_IN_FMT_SIGNED);
+ sel_input_logic_inverted = true;
+ }
+
+ /* Input selection */
+ tvout_vip_set_sel_input(tvout, TVO_VIP_DVO, main_path,
+ sel_input_logic_inverted,
+ STI_TVOUT_VIDEO_OUT_RGB);
+}
+
+/**
* Start VIP block for HDMI output
*
* @tvout: pointer on tvout structure
@@ -402,6 +469,56 @@ static const struct drm_encoder_funcs sti_tvout_encoder_funcs = {
.destroy = sti_tvout_encoder_destroy,
};
+static void sti_dvo_encoder_commit(struct drm_encoder *encoder)
+{
+ struct sti_tvout *tvout = to_sti_tvout(encoder);
+
+ tvout_dvo_start(tvout, sti_drm_crtc_is_main(encoder->crtc));
+}
+
+static void sti_dvo_encoder_disable(struct drm_encoder *encoder)
+{
+ struct sti_tvout *tvout = to_sti_tvout(encoder);
+
+ /* Reset VIP register */
+ tvout_write(tvout, 0x0, TVO_VIP_DVO);
+}
+
+static const struct drm_encoder_helper_funcs sti_dvo_encoder_helper_funcs = {
+ .dpms = sti_tvout_encoder_dpms,
+ .mode_fixup = sti_tvout_encoder_mode_fixup,
+ .mode_set = sti_tvout_encoder_mode_set,
+ .prepare = sti_tvout_encoder_prepare,
+ .commit = sti_dvo_encoder_commit,
+ .disable = sti_dvo_encoder_disable,
+};
+
+static struct drm_encoder *
+sti_tvout_create_dvo_encoder(struct drm_device *dev,
+ struct sti_tvout *tvout)
+{
+ struct sti_tvout_encoder *encoder;
+ struct drm_encoder *drm_encoder;
+
+ encoder = devm_kzalloc(tvout->dev, sizeof(*encoder), GFP_KERNEL);
+ if (!encoder)
+ return NULL;
+
+ encoder->tvout = tvout;
+
+ drm_encoder = (struct drm_encoder *)encoder;
+
+ drm_encoder->possible_crtcs = ENCODER_CRTC_MASK;
+ drm_encoder->possible_clones = 1 << 0;
+
+ drm_encoder_init(dev, drm_encoder,
+ &sti_tvout_encoder_funcs, DRM_MODE_ENCODER_LVDS);
+
+ drm_encoder_helper_add(drm_encoder, &sti_dvo_encoder_helper_funcs);
+
+ return drm_encoder;
+}
+
static void sti_hda_encoder_commit(struct drm_encoder *encoder)
{
struct sti_tvout *tvout = to_sti_tvout(encoder);
@@ -508,6 +625,7 @@ static void sti_tvout_create_encoders(struct drm_device *dev,
{
tvout->hdmi = sti_tvout_create_hdmi_encoder(dev, tvout);
tvout->hda = sti_tvout_create_hda_encoder(dev, tvout);
+ tvout->dvo = sti_tvout_create_dvo_encoder(dev, tvout);
}
static void sti_tvout_destroy_encoders(struct sti_tvout *tvout)
Digital Video Out connector driver LCD panels. Like HDMI and HDA it create bridge, encoder and connector drm object. Add binding descrition. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> --- .../devicetree/bindings/gpu/st,stih4xx.txt | 29 ++ drivers/gpu/drm/sti/Makefile | 4 + drivers/gpu/drm/sti/sti_awg_utils.c | 184 +++++++ drivers/gpu/drm/sti/sti_awg_utils.h | 34 ++ drivers/gpu/drm/sti/sti_dvo.c | 551 +++++++++++++++++++++ drivers/gpu/drm/sti/sti_tvout.c | 118 +++++ 6 files changed, 920 insertions(+) create mode 100644 drivers/gpu/drm/sti/sti_awg_utils.c create mode 100644 drivers/gpu/drm/sti/sti_awg_utils.h create mode 100644 drivers/gpu/drm/sti/sti_dvo.c