new file mode 100644
@@ -0,0 +1,72 @@
+Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver
+
+A DSI Host Controller resides in the middle of display controller and external
+HDMI converter or panel.
+
+Required properties:
+- compatible: value should be "hisilicon,hi6220-dsi".
+- reg: physical base address and length of dsi controller's registers.
+- clocks: contains APB clock phandle + clock-specifier pair.
+- clock-names: should be "pclk".
+- ports: contains DSI controller input and output sub port.
+ The input port connects to ADE output port with the reg value "0".
+ The output port with the reg value "1", it could connect to panel or
+ any other bridge endpoints.
+ See Documentation/devicetree/bindings/graph.txt for more device graph info.
+
+A example of HiKey board hi6220 SoC and board specific DT entry:
+Example:
+
+SoC specific:
+ dsi: dsi@f4107800 {
+ compatible = "hisilicon,hi6220-dsi";
+ reg = <0x0 0xf4107800 0x0 0x100>;
+ clocks = <&media_ctrl HI6220_DSI_PCLK>;
+ clock-names = "pclk";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 0 for input port */
+ port@0 {
+ reg = <0>;
+ dsi_in: endpoint {
+ remote-endpoint = <&ade_out>;
+ };
+ };
+ };
+ };
+
+
+Board specific:
+ &dsi {
+ status = "ok";
+
+ ports {
+ /* 1 for output port */
+ port@1 {
+ reg = <1>;
+
+ dsi_out0: endpoint@0 {
+ remote-endpoint = <&adv7533_in>;
+ };
+ };
+ };
+ };
+
+ &i2c2 {
+ ...
+
+ adv7533: adv7533@39 {
+ ...
+
+ port {
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi_out0>;
+ };
+ };
+ };
+ };
+
new file mode 100644
@@ -0,0 +1,64 @@
+Device-Tree bindings for hisilicon ADE display controller driver
+
+ADE (Advanced Display Engine) is the display controller which grab image
+data from memory, do composition, do post image processing, generate RGB
+timing stream and transfer to DSI.
+
+Required properties:
+- compatible: value should be "hisilicon,hi6220-ade".
+- reg: physical base address and length of the ADE controller's registers.
+- hisilicon,noc-syscon: ADE NOC QoS syscon.
+- resets: The ADE reset controller node.
+- interrupt: the ldi vblank interrupt number used.
+- clocks: a list of phandle + clock-specifier pairs, one for each entry
+ in clock-names.
+- clock-names: should contain:
+ "clk_ade_core" for the ADE core clock.
+ "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with
+ jpeg codec.
+ "clk_ade_pix" for the ADE pixel clok.
+- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks'
+ phandle + clock-specifier pairs.
+- assigned-clock-rates: clock rates, one for each entry in assigned-clocks.
+ The rate of "clk_ade_core" could be "360000000" or "180000000";
+ The rate of "clk_codec_jpeg" could be or less than "1440000000".
+ These rate values could be configured according to performance and power
+ consumption.
+- port: the output port. This contains one endpoint subnode, with its
+ remote-endpoint set to the phandle of the connected DSI input endpoint.
+ See Documentation/devicetree/bindings/graph.txt for more device graph info.
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent.
+
+
+A example of HiKey board hi6220 SoC specific DT entry:
+Example:
+
+ ade: ade@f4100000 {
+ compatible = "hisilicon,hi6220-ade";
+ reg = <0x0 0xf4100000 0x0 0x7800>;
+ reg-names = "ade_base";
+ hisilicon,noc-syscon = <&medianoc_ade>;
+ resets = <&media_ctrl MEDIA_ADE>;
+ interrupts = <0 115 4>; /* ldi interrupt */
+
+ clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>,
+ <&media_ctrl HI6220_ADE_PIX_SRC>;
+ /*clock name*/
+ clock-names = "clk_ade_core",
+ "clk_codec_jpeg",
+ "clk_ade_pix";
+
+ assigned-clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>;
+ assigned-clock-rates = <360000000>, <288000000>;
+ dma-coherent;
+
+ port {
+ ade_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ };
+ };
+ };