@@ -2,7 +2,7 @@
* Copyright (C) 2013-2014 Red Hat
* Author: Rob Clark <robdclark@gmail.com>
*
- * Copyright (c) 2014 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2014,2017 The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published by
@@ -238,7 +238,6 @@ static int adreno_bind(struct device *dev, struct device *master, void *data)
/* find clock rates: */
config.fast_rate = 0;
- config.slow_rate = ~0;
for_each_child_of_node(node, child) {
if (of_device_is_compatible(child, "qcom,gpu-pwrlevels")) {
struct device_node *pwrlvl;
@@ -249,7 +248,6 @@ static int adreno_bind(struct device *dev, struct device *master, void *data)
return ret;
}
config.fast_rate = max(config.fast_rate, val);
- config.slow_rate = min(config.slow_rate, val);
}
}
}
@@ -258,7 +256,6 @@ static int adreno_bind(struct device *dev, struct device *master, void *data)
dev_warn(dev, "could not find clk rates\n");
/* This is a safe low speed for all devices: */
config.fast_rate = 200000000;
- config.slow_rate = 27000000;
}
dev->platform_data = &config;
@@ -407,14 +407,13 @@ int adreno_gpu_init(struct drm_device *drm, struct platform_device *pdev,
adreno_gpu->rev = config->rev;
gpu->fast_rate = config->fast_rate;
- gpu->slow_rate = config->slow_rate;
gpu->bus_freq = config->bus_freq;
#ifdef DOWNSTREAM_CONFIG_MSM_BUS_SCALING
gpu->bus_scale_table = config->bus_scale_table;
#endif
- DBG("fast_rate=%u, slow_rate=%u, bus_freq=%u",
- gpu->fast_rate, gpu->slow_rate, gpu->bus_freq);
+ DBG("fast_rate=%u, slow_rate=27000000, bus_freq=%u",
+ gpu->fast_rate, gpu->bus_freq);
adreno_gpu_config.ioname = "kgsl_3d0_reg_memory";
adreno_gpu_config.irqname = "kgsl_3d0_irq";
@@ -128,7 +128,7 @@ struct adreno_gpu {
/* platform config data (ie. from DT, or pdata) */
struct adreno_platform_config {
struct adreno_rev rev;
- uint32_t fast_rate, slow_rate, bus_freq;
+ uint32_t fast_rate, bus_freq;
#ifdef DOWNSTREAM_CONFIG_MSM_BUS_SCALING
struct msm_bus_scale_pdata *bus_scale_table;
#endif
@@ -123,8 +123,12 @@ static int disable_clk(struct msm_gpu *gpu)
if (gpu->grp_clks[i])
clk_unprepare(gpu->grp_clks[i]);
- if (gpu->grp_clks[0] && gpu->slow_rate)
- clk_set_rate(gpu->grp_clks[0], gpu->slow_rate);
+ /*
+ * Set the clock to a deliberately low rate. On older targets the clock
+ * speed had to be non zero to avoid problems. On newer targets this
+ * will be rounded down to zero anyway so it all works out.
+ */
+ clk_set_rate(gpu->grp_clks[0], 27000000);
if (gpu->grp_clks[2])
clk_set_rate(gpu->grp_clks[2], 0);
@@ -111,7 +111,7 @@ struct msm_gpu {
/* Power Control: */
struct regulator *gpu_reg, *gpu_cx;
struct clk *ebi1_clk, *grp_clks[6];
- uint32_t fast_rate, slow_rate, bus_freq;
+ uint32_t fast_rate, bus_freq;
#ifdef DOWNSTREAM_CONFIG_MSM_BUS_SCALING
struct msm_bus_scale_pdata *bus_scale_table;
Some A3XX and A4XX GPU targets required that the GPU clock be programmed to a non zero value when it was disabled so 27Mhz was chosen as the "invalid" frequency. Even though newer targets do not have the same clock restrictions we still write 27Mhz on clock disable and expect the clock subsystem to round down to zero. For unknown reasons even though the slow clock speed is always 27Mhz and it isn't actually a functional level the legacy device tree frequency tables always defined it and then did gymnastics to work around it. Instead of playing the same silly games just hard code the "slow" clock speed in the code as 27MHz and save ourselves a bit of infrastructure. Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> --- drivers/gpu/drm/msm/adreno/adreno_device.c | 5 +---- drivers/gpu/drm/msm/adreno/adreno_gpu.c | 5 ++--- drivers/gpu/drm/msm/adreno/adreno_gpu.h | 2 +- drivers/gpu/drm/msm/msm_gpu.c | 8 ++++++-- drivers/gpu/drm/msm/msm_gpu.h | 2 +- 5 files changed, 11 insertions(+), 11 deletions(-)