new file mode 100644
@@ -0,0 +1,76 @@
+SN65DSI86 DSI to eDP bridge chip
+--------------------------------
+
+This is the binding for Texas Instruments SN65DSI86 bridge.
+http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
+
+Required properties:
+- compatible: Must be "ti,sn65dsi86"
+- reg: i2c address of the chip, 0x2d as per datasheet
+- enable-gpios: OF device-tree gpio specification for bridge_en pin
+
+- vccio-supply: A 1.8V supply that powers up the digital IOs.
+- vpll-supply: A 1.8V supply that powers up the displayport PLL.
+- vcca-supply: A 1.2V supply that powers up the analog circuits.
+- vcc-supply: A 1.2V supply that powers up the digital core.
+
+Optional properties:
+- interrupts: Specifier for the SN65DSI86 interrupt line.
+- hpd-gpios: OF device-tree gpio specifications for HPD pin.
+
+- refclk-freq-khz: Value specifying the frequency of reference clock in KHz unit.
+
+- gpio-controller: Marks the device has a GPIO controller.
+- #gpio-cells: Number of GPIO cells. Refer to binding document "gpio/gpio.txt"
+- #pwm-cells : Number of cells used to specify a PWM. See pwm.txt in this directory
+ for a description of the cell formats.
+
+Required nodes:
+
+This device has two video ports. Their connections are modelled using the
+OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for DSI input
+- Video port 1 for eDP output
+
+Example
+-------
+
+edp-bridge@2d {
+ compatible = "ti,sn65dsi86";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2d>;
+
+ enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+
+ vccio-supply = <&pm8916_l17>;
+ vcca-supply = <&pm8916_l6>;
+ vpll-supply = <&pm8916_l17>;
+ vcc-supply = <&pm8916_l6>;
+
+ refclk-freq-khz = <19200>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ edp_bridge_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ edp_bridge_out: endpoint {
+ remote-endpoint = <&edp_panel_in>;
+ };
+ };
+ };
+}
Document the bindings used for the sn65dsi86 DSI to eDP bridge. Changes in v1: - Rephrase the dt-binding descriptions to be more inline with existing bindings (Andrzej Hajda). - Add missing dt-binding that are parsed by corresponding driver (Andrzej Hajda). Changes in v2: - Remove edp panel specific dt-binding entries. Only keep bridge specific entries (Sean Paul). - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). Changes in v3: - Remove irq-gpio dt entry and instead populate is an interrupt property (Rob Herring). Changes in v4: - Add link to bridge chip datasheet (Stephen Boyd) - Add vpll and vcc regulator supply bindings (Stephen Boyd) - Add ref clk optional dt binding (Stephen Boyd) - Add gpio-controller optional dt binding (Stephen Boyd) Signed-off-by: Sandeep Panda <spanda@codeaurora.org> --- .../bindings/display/bridge/ti,sn65dsi86.txt | 76 ++++++++++++++++++++++ 1 file changed, 76 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt