@@ -131,21 +131,30 @@ struct v4l2_fwnode_link {
* @fwnode: pointer to the endpoint's fwnode handle
* @vep: pointer to the V4L2 fwnode data structure
*
- * All properties are optional. If none are found, we don't set any flags. This
- * means the port has a static configuration and no properties have to be
- * specified explicitly. If any properties that identify the bus as parallel
- * are found and slave-mode isn't set, we set V4L2_MBUS_MASTER. Similarly, if
- * we recognise the bus as serial CSI-2 and clock-noncontinuous isn't set, we
- * set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a
- * reference to @fwnode.
- *
- * The caller must set the bus_type field of @vep to zero.
+ * This function parses the V4L2 fwnode endpoint specific parameters from the
+ * firmware. The caller is responsible for assigning @vep.bus_type to a valid
+ * media bus type. The caller may also set the default configuration for the
+ * endpoint --- a configuration that shall be in line with the DT binding
+ * documentation. Should a device support multiple bus types, the caller may
+ * call this function once the correct type is found --- with a default
+ * configuration valid for that type.
+ *
+ * As a compatibility means guessing the bus type is also supported by setting
+ * @vep.bus_type to V4L2_MBUS_UNKNOWN. The caller may not provide a default
+ * configuration in this case as the defaults are specific to a given bus type.
+ * This functionality is deprecated and should not be used in new drivers and it
+ * is only supported for CSI-2 D-PHY, parallel and Bt.656 busses.
+ *
+ * The function does not change the V4L2 fwnode endpoint state if it fails.
*
* NOTE: This function does not parse properties the size of which is variable
* without a low fixed limit. Please use v4l2_fwnode_endpoint_alloc_parse() in
* new drivers instead.
*
- * Return: 0 on success or a negative error code on failure.
+ * Return: %0 on success or a negative error code on failure:
+ * %-ENOMEM on memory allocation failure
+ * %-EINVAL on parsing failure
+ * %-ENXIO on mismatching bus types
*/
int v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,
struct v4l2_fwnode_endpoint *vep);
@@ -165,15 +174,21 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);
* @fwnode: pointer to the endpoint's fwnode handle
* @vep: pointer to the V4L2 fwnode data structure
*
- * All properties are optional. If none are found, we don't set any flags. This
- * means the port has a static configuration and no properties have to be
- * specified explicitly. If any properties that identify the bus as parallel
- * are found and slave-mode isn't set, we set V4L2_MBUS_MASTER. Similarly, if
- * we recognise the bus as serial CSI-2 and clock-noncontinuous isn't set, we
- * set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a
- * reference to @fwnode.
+ * This function parses the V4L2 fwnode endpoint specific parameters from the
+ * firmware. The caller is responsible for assigning @vep.bus_type to a valid
+ * media bus type. The caller may also set the default configuration for the
+ * endpoint --- a configuration that shall be in line with the DT binding
+ * documentation. Should a device support multiple bus types, the caller may
+ * call this function once the correct type is found --- with a default
+ * configuration valid for that type.
+ *
+ * As a compatibility means guessing the bus type is also supported by setting
+ * @vep.bus_type to V4L2_MBUS_UNKNOWN. The caller may not provide a default
+ * configuration in this case as the defaults are specific to a given bus type.
+ * This functionality is deprecated and should not be used in new drivers and it
+ * is only supported for CSI-2 D-PHY, parallel and Bt.656 busses.
*
- * The caller must set the bus_type field of @vep to zero.
+ * The function does not change the V4L2 fwnode endpoint state if it fails.
*
* v4l2_fwnode_endpoint_alloc_parse() has two important differences to
* v4l2_fwnode_endpoint_parse():
@@ -183,7 +198,10 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);
* 2. The memory it has allocated to store the variable size data must be freed
* using v4l2_fwnode_endpoint_free() when no longer needed.
*
- * Return: 0 on success or a negative error code on failure.
+ * Return: %0 on success or a negative error code on failure:
+ * %-ENOMEM on memory allocation failure
+ * %-EINVAL on parsing failure
+ * %-ENXIO on mismatching bus types
*/
int v4l2_fwnode_endpoint_alloc_parse(
struct fwnode_handle *fwnode, struct v4l2_fwnode_endpoint *vep);