@@ -525,13 +525,25 @@ static void ltdc_crtc_mode_set_nofb(struct drm_crtc *crtc)
{
struct ltdc_device *ldev = crtc_to_ltdc(crtc);
struct drm_device *ddev = crtc->dev;
+ struct drm_connector_list_iter iter;
+ struct drm_connector *connector;
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
struct videomode vm;
+ u32 bus_flags = 0;
u32 hsync, vsync, accum_hbp, accum_vbp, accum_act_w, accum_act_h;
u32 total_width, total_height;
u32 val;
int ret;
+ /* Get the connector which is connected */
+ drm_connector_list_iter_begin(ddev, &iter);
+ drm_for_each_connector_iter(connector, &iter)
+ if(connector->status == connector_status_connected)
+ break;
+ drm_connector_list_iter_end(&iter);
+
+ bus_flags = connector->display_info.bus_flags;
+
if (!pm_runtime_active(ddev->dev)) {
ret = pm_runtime_get_sync(ddev->dev);
if (ret) {
@@ -567,10 +579,10 @@ static void ltdc_crtc_mode_set_nofb(struct drm_crtc *crtc)
if (vm.flags & DISPLAY_FLAGS_VSYNC_HIGH)
val |= GCR_VSPOL;
- if (vm.flags & DISPLAY_FLAGS_DE_LOW)
+ if (bus_flags & DRM_BUS_FLAG_DE_LOW)
val |= GCR_DEPOL;
- if (vm.flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
+ if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
val |= GCR_PCPOL;
reg_update_bits(ldev->regs, LTDC_GCR,
@@ -1078,6 +1090,8 @@ static const struct drm_encoder_helper_funcs ltdc_encoder_helper_funcs = {
static int ltdc_encoder_init(struct drm_device *ddev, struct drm_bridge *bridge)
{
+ struct ltdc_device *ldev = ddev->dev_private;
+ struct drm_connector_list_iter iter;
struct drm_encoder *encoder;
int ret;
@@ -1099,6 +1113,16 @@ static int ltdc_encoder_init(struct drm_device *ddev, struct drm_bridge *bridge)
return -EINVAL;
}
+ ldev->bridge = bridge;
+
+ /*
+ * Get hold of the connector. This is a bit of a hack, until the bridge
+ * API gives us bus flags and formats.
+ */
+ drm_connector_list_iter_begin(ddev, &iter);
+ ldev->connector = drm_connector_list_iter_next(&iter);
+ drm_connector_list_iter_end(&iter);
+
DRM_DEBUG_DRIVER("Bridge encoder:%d created\n", encoder->base.id);
return 0;
@@ -38,6 +38,8 @@ struct ltdc_device {
u32 irq_status;
struct fps_info plane_fpsi[LTDC_MAX_LAYER];
struct drm_atomic_state *suspend_state;
+ struct drm_bridge *bridge;
+ struct drm_connector *connector;
};
int ltdc_load(struct drm_device *ddev);
The drm_display_mode_to_videomode() does not populate DISPLAY_FLAGS_DE_LOW or DISPLAY_FLAGS_PIXDATA_NEGEDGE flags in struct videomode. Therefore, no matter what polarity the next bridge or display might require, these flags are never set, and thus the LTDC GCR_DEPOL and GCR_PCPOL bits are never set, and the LTDC behaves as if both DISPLAY_FLAGS_PIXDATA_POSEDGE and DISPLAY_FLAGS_DE_HIGH were always set. The fix for this problem is taken almost verbatim from MXSFB driver. In case there is a bridge attached to the LTDC, the bridge might have extra polarity requirements, so extract bus_flags from the bridge and use them for LTDC configuration. Otherwise, extract bus_flags from the connector, which is the display. Fixes: b759012c5fa7 ("drm/stm: Add STM32 LTDC driver") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Antonio Borneo <antonio.borneo@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com To: dri-devel@lists.freedesktop.org --- V2: Check if ldev->bridge->timings is non-NULL before accessing it V3: get bus_flags from connector (from Yannick) - Display controller could support several connectors (not connected at the same time). ie: stm32mp15c-DK2 board have 2 connectors (HDMI + DSI). Driver check which connector is connected to get the bus flag. --- drivers/gpu/drm/stm/ltdc.c | 28 ++++++++++++++++++++++++++-- drivers/gpu/drm/stm/ltdc.h | 2 ++ 2 files changed, 28 insertions(+), 2 deletions(-)