| Message ID | 20210215161537.14696-2-jonathan@marek.ca (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: qcom: sm8250: fix display nodes | expand |
On Mon, 15 Feb 2021 at 19:25, Jonathan Marek <jonathan@marek.ca> wrote: > > The driver already has support for sm8150/sm8250, but the compatibles were > never added. > > Also inverse the non-mdp4 condition in add_display_components() to avoid > having to check every new compatible in the condition. > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> > --- > Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++-- > drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ > drivers/gpu/drm/msm/msm_drv.c | 6 +++--- > 3 files changed, 7 insertions(+), 5 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt > index 551ae26f60da..5763f43200a0 100644 > --- a/Documentation/devicetree/bindings/display/msm/dpu.txt > +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt > @@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC. > > MDSS: > Required properties: > -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" > +- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss", "qcom,sm8150-mdss", "qcom,sm8250-mdss" > - reg: physical base address and length of contoller's registers. > - reg-names: register region names. The following region is required: > * "mdss" > @@ -41,7 +41,7 @@ Optional properties: > > MDP: > Required properties: > -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" > +- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu", "qcom,sm8150-dpu", "qcom,sm8250-dpu" > - reg: physical base address and length of controller's registers. > - reg-names : register region names. The following region is required: > * "mdp" These two chunks should probably go to the separate patch 'dt-bindings:...'. Also, could you please pinpoint the reason for adding more compatibility strings, while they map to the same internal data? I think we might want instead to use some generic name for the dpu block, like "qcom,dpu" or "qcom,mdp-dpu" instead of specifying the platform name. > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > index 5a8e3e1fc48c..fff12a4c8bfc 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > @@ -1219,6 +1219,8 @@ static const struct dev_pm_ops dpu_pm_ops = { > static const struct of_device_id dpu_dt_match[] = { > { .compatible = "qcom,sdm845-dpu", }, > { .compatible = "qcom,sc7180-dpu", }, > + { .compatible = "qcom,sm8150-dpu", }, > + { .compatible = "qcom,sm8250-dpu", }, > {} > }; > MODULE_DEVICE_TABLE(of, dpu_dt_match); > diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c > index 94525ac76d4e..928f13d4bfbc 100644 > --- a/drivers/gpu/drm/msm/msm_drv.c > +++ b/drivers/gpu/drm/msm/msm_drv.c > @@ -1185,9 +1185,7 @@ static int add_display_components(struct device *dev, > * Populate the children devices, find the MDP5/DPU node, and then add > * the interfaces to our components list. > */ > - if (of_device_is_compatible(dev->of_node, "qcom,mdss") || > - of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") || > - of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) { > + if (!of_device_is_compatible(dev->of_node, "qcom,mdp4")) { > ret = of_platform_populate(dev->of_node, NULL, NULL, dev); > if (ret) { > DRM_DEV_ERROR(dev, "failed to populate children devices\n"); > @@ -1320,6 +1318,8 @@ static const struct of_device_id dt_match[] = { > { .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 }, > { .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU }, > { .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU }, > + { .compatible = "qcom,sm8150-mdss", .data = (void *)KMS_DPU }, > + { .compatible = "qcom,sm8250-mdss", .data = (void *)KMS_DPU }, > {} > }; > MODULE_DEVICE_TABLE(of, dt_match); > -- > 2.26.1 >
On 2/16/21 11:54 AM, Dmitry Baryshkov wrote: > On Mon, 15 Feb 2021 at 19:25, Jonathan Marek <jonathan@marek.ca> wrote: >> >> The driver already has support for sm8150/sm8250, but the compatibles were >> never added. >> >> Also inverse the non-mdp4 condition in add_display_components() to avoid >> having to check every new compatible in the condition. >> >> Signed-off-by: Jonathan Marek <jonathan@marek.ca> >> --- >> Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++-- >> drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ >> drivers/gpu/drm/msm/msm_drv.c | 6 +++--- >> 3 files changed, 7 insertions(+), 5 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt >> index 551ae26f60da..5763f43200a0 100644 >> --- a/Documentation/devicetree/bindings/display/msm/dpu.txt >> +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt >> @@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC. >> >> MDSS: >> Required properties: >> -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" >> +- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss", "qcom,sm8150-mdss", "qcom,sm8250-mdss" >> - reg: physical base address and length of contoller's registers. >> - reg-names: register region names. The following region is required: >> * "mdss" >> @@ -41,7 +41,7 @@ Optional properties: >> >> MDP: >> Required properties: >> -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" >> +- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu", "qcom,sm8150-dpu", "qcom,sm8250-dpu" >> - reg: physical base address and length of controller's registers. >> - reg-names : register region names. The following region is required: >> * "mdp" > > These two chunks should probably go to the separate patch 'dt-bindings:...'. > In this case I think its better to have this change in the same patch, but maybe one of the Robs will disagree. > Also, could you please pinpoint the reason for adding more > compatibility strings, while they map to the same internal data? > I think we might want instead to use some generic name for the dpu > block, like "qcom,dpu" or "qcom,mdp-dpu" instead of specifying the > platform name. > sdm845 and sc7180 aren't using generic compatibles, this is just being consistent with that. > >> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c >> index 5a8e3e1fc48c..fff12a4c8bfc 100644 >> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c >> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c >> @@ -1219,6 +1219,8 @@ static const struct dev_pm_ops dpu_pm_ops = { >> static const struct of_device_id dpu_dt_match[] = { >> { .compatible = "qcom,sdm845-dpu", }, >> { .compatible = "qcom,sc7180-dpu", }, >> + { .compatible = "qcom,sm8150-dpu", }, >> + { .compatible = "qcom,sm8250-dpu", }, >> {} >> }; >> MODULE_DEVICE_TABLE(of, dpu_dt_match); >> diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c >> index 94525ac76d4e..928f13d4bfbc 100644 >> --- a/drivers/gpu/drm/msm/msm_drv.c >> +++ b/drivers/gpu/drm/msm/msm_drv.c >> @@ -1185,9 +1185,7 @@ static int add_display_components(struct device *dev, >> * Populate the children devices, find the MDP5/DPU node, and then add >> * the interfaces to our components list. >> */ >> - if (of_device_is_compatible(dev->of_node, "qcom,mdss") || >> - of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") || >> - of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) { >> + if (!of_device_is_compatible(dev->of_node, "qcom,mdp4")) { >> ret = of_platform_populate(dev->of_node, NULL, NULL, dev); >> if (ret) { >> DRM_DEV_ERROR(dev, "failed to populate children devices\n"); >> @@ -1320,6 +1318,8 @@ static const struct of_device_id dt_match[] = { >> { .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 }, >> { .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU }, >> { .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU }, >> + { .compatible = "qcom,sm8150-mdss", .data = (void *)KMS_DPU }, >> + { .compatible = "qcom,sm8250-mdss", .data = (void *)KMS_DPU }, >> {} >> }; >> MODULE_DEVICE_TABLE(of, dt_match); >> -- >> 2.26.1 >> > >
On Tue, 16 Feb 2021 at 21:06, Jonathan Marek <jonathan@marek.ca> wrote: > > On 2/16/21 11:54 AM, Dmitry Baryshkov wrote: > > On Mon, 15 Feb 2021 at 19:25, Jonathan Marek <jonathan@marek.ca> wrote: > >> > >> The driver already has support for sm8150/sm8250, but the compatibles were > >> never added. > >> > >> Also inverse the non-mdp4 condition in add_display_components() to avoid > >> having to check every new compatible in the condition. > >> > >> Signed-off-by: Jonathan Marek <jonathan@marek.ca> > >> --- > >> Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++-- > >> drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ > >> drivers/gpu/drm/msm/msm_drv.c | 6 +++--- > >> 3 files changed, 7 insertions(+), 5 deletions(-) > >> > >> diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt > >> index 551ae26f60da..5763f43200a0 100644 > >> --- a/Documentation/devicetree/bindings/display/msm/dpu.txt > >> +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt > >> @@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC. > >> > >> MDSS: > >> Required properties: > >> -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" > >> +- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss", "qcom,sm8150-mdss", "qcom,sm8250-mdss" > >> - reg: physical base address and length of contoller's registers. > >> - reg-names: register region names. The following region is required: > >> * "mdss" > >> @@ -41,7 +41,7 @@ Optional properties: > >> > >> MDP: > >> Required properties: > >> -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" > >> +- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu", "qcom,sm8150-dpu", "qcom,sm8250-dpu" > >> - reg: physical base address and length of controller's registers. > >> - reg-names : register region names. The following region is required: > >> * "mdp" > > > > These two chunks should probably go to the separate patch 'dt-bindings:...'. > > > > In this case I think its better to have this change in the same patch, > but maybe one of the Robs will disagree. > > > Also, could you please pinpoint the reason for adding more > > compatibility strings, while they map to the same internal data? > > I think we might want instead to use some generic name for the dpu > > block, like "qcom,dpu" or "qcom,mdp-dpu" instead of specifying the > > platform name. > > > > sdm845 and sc7180 aren't using generic compatibles, this is just being > consistent with that. Well, I suppose the common case is to use the 'first compatible' entry if the entities are compatible. The generic compatibles is a proposal, not an affirmation. Please excuse me if it sounded in a different way. > > > > >> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > >> index 5a8e3e1fc48c..fff12a4c8bfc 100644 > >> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > >> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > >> @@ -1219,6 +1219,8 @@ static const struct dev_pm_ops dpu_pm_ops = { > >> static const struct of_device_id dpu_dt_match[] = { > >> { .compatible = "qcom,sdm845-dpu", }, > >> { .compatible = "qcom,sc7180-dpu", }, > >> + { .compatible = "qcom,sm8150-dpu", }, > >> + { .compatible = "qcom,sm8250-dpu", }, > >> {} > >> }; > >> MODULE_DEVICE_TABLE(of, dpu_dt_match); > >> diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c > >> index 94525ac76d4e..928f13d4bfbc 100644 > >> --- a/drivers/gpu/drm/msm/msm_drv.c > >> +++ b/drivers/gpu/drm/msm/msm_drv.c > >> @@ -1185,9 +1185,7 @@ static int add_display_components(struct device *dev, > >> * Populate the children devices, find the MDP5/DPU node, and then add > >> * the interfaces to our components list. > >> */ > >> - if (of_device_is_compatible(dev->of_node, "qcom,mdss") || > >> - of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") || > >> - of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) { > >> + if (!of_device_is_compatible(dev->of_node, "qcom,mdp4")) { > >> ret = of_platform_populate(dev->of_node, NULL, NULL, dev); > >> if (ret) { > >> DRM_DEV_ERROR(dev, "failed to populate children devices\n"); > >> @@ -1320,6 +1318,8 @@ static const struct of_device_id dt_match[] = { > >> { .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 }, > >> { .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU }, > >> { .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU }, > >> + { .compatible = "qcom,sm8150-mdss", .data = (void *)KMS_DPU }, > >> + { .compatible = "qcom,sm8250-mdss", .data = (void *)KMS_DPU }, > >> {} > >> }; > >> MODULE_DEVICE_TABLE(of, dt_match); > >> -- > >> 2.26.1 > >> > > > >
On Tue, Feb 16, 2021 at 10:06 AM Jonathan Marek <jonathan@marek.ca> wrote: > > On 2/16/21 11:54 AM, Dmitry Baryshkov wrote: > > On Mon, 15 Feb 2021 at 19:25, Jonathan Marek <jonathan@marek.ca> wrote: > >> > >> The driver already has support for sm8150/sm8250, but the compatibles were > >> never added. > >> > >> Also inverse the non-mdp4 condition in add_display_components() to avoid > >> having to check every new compatible in the condition. > >> > >> Signed-off-by: Jonathan Marek <jonathan@marek.ca> > >> --- > >> Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++-- > >> drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ > >> drivers/gpu/drm/msm/msm_drv.c | 6 +++--- > >> 3 files changed, 7 insertions(+), 5 deletions(-) > >> > >> diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt > >> index 551ae26f60da..5763f43200a0 100644 > >> --- a/Documentation/devicetree/bindings/display/msm/dpu.txt > >> +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt > >> @@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC. > >> > >> MDSS: > >> Required properties: > >> -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" > >> +- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss", "qcom,sm8150-mdss", "qcom,sm8250-mdss" > >> - reg: physical base address and length of contoller's registers. > >> - reg-names: register region names. The following region is required: > >> * "mdss" > >> @@ -41,7 +41,7 @@ Optional properties: > >> > >> MDP: > >> Required properties: > >> -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" > >> +- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu", "qcom,sm8150-dpu", "qcom,sm8250-dpu" > >> - reg: physical base address and length of controller's registers. > >> - reg-names : register region names. The following region is required: > >> * "mdp" > > > > These two chunks should probably go to the separate patch 'dt-bindings:...'. > > > > In this case I think its better to have this change in the same patch, > but maybe one of the Robs will disagree. I *think* typically the reason to split dt bindings into their own patch is that devicetree@ list isn't interested in reviewing driver changes, just binding changes.. In this case since it is just adding a compatible I think it is ok.. (or at least ok by me, but maybe other-Rob disagrees ;-)) > > Also, could you please pinpoint the reason for adding more > > compatibility strings, while they map to the same internal data? > > I think we might want instead to use some generic name for the dpu > > block, like "qcom,dpu" or "qcom,mdp-dpu" instead of specifying the > > platform name. > > > > sdm845 and sc7180 aren't using generic compatibles, this is just being > consistent with that. It is good to have a device specific compatible up front, even if we fallback to the more generic one for matching.. just in case we find a reason for needing it later BR, -R > > > >> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > >> index 5a8e3e1fc48c..fff12a4c8bfc 100644 > >> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > >> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c > >> @@ -1219,6 +1219,8 @@ static const struct dev_pm_ops dpu_pm_ops = { > >> static const struct of_device_id dpu_dt_match[] = { > >> { .compatible = "qcom,sdm845-dpu", }, > >> { .compatible = "qcom,sc7180-dpu", }, > >> + { .compatible = "qcom,sm8150-dpu", }, > >> + { .compatible = "qcom,sm8250-dpu", }, > >> {} > >> }; > >> MODULE_DEVICE_TABLE(of, dpu_dt_match); > >> diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c > >> index 94525ac76d4e..928f13d4bfbc 100644 > >> --- a/drivers/gpu/drm/msm/msm_drv.c > >> +++ b/drivers/gpu/drm/msm/msm_drv.c > >> @@ -1185,9 +1185,7 @@ static int add_display_components(struct device *dev, > >> * Populate the children devices, find the MDP5/DPU node, and then add > >> * the interfaces to our components list. > >> */ > >> - if (of_device_is_compatible(dev->of_node, "qcom,mdss") || > >> - of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") || > >> - of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) { > >> + if (!of_device_is_compatible(dev->of_node, "qcom,mdp4")) { > >> ret = of_platform_populate(dev->of_node, NULL, NULL, dev); > >> if (ret) { > >> DRM_DEV_ERROR(dev, "failed to populate children devices\n"); > >> @@ -1320,6 +1318,8 @@ static const struct of_device_id dt_match[] = { > >> { .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 }, > >> { .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU }, > >> { .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU }, > >> + { .compatible = "qcom,sm8150-mdss", .data = (void *)KMS_DPU }, > >> + { .compatible = "qcom,sm8250-mdss", .data = (void *)KMS_DPU }, > >> {} > >> }; > >> MODULE_DEVICE_TABLE(of, dt_match); > >> -- > >> 2.26.1 > >> > > > >
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt index 551ae26f60da..5763f43200a0 100644 --- a/Documentation/devicetree/bindings/display/msm/dpu.txt +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt @@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC. MDSS: Required properties: -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" +- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss", "qcom,sm8150-mdss", "qcom,sm8250-mdss" - reg: physical base address and length of contoller's registers. - reg-names: register region names. The following region is required: * "mdss" @@ -41,7 +41,7 @@ Optional properties: MDP: Required properties: -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" +- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu", "qcom,sm8150-dpu", "qcom,sm8250-dpu" - reg: physical base address and length of controller's registers. - reg-names : register region names. The following region is required: * "mdp" diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c index 5a8e3e1fc48c..fff12a4c8bfc 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c @@ -1219,6 +1219,8 @@ static const struct dev_pm_ops dpu_pm_ops = { static const struct of_device_id dpu_dt_match[] = { { .compatible = "qcom,sdm845-dpu", }, { .compatible = "qcom,sc7180-dpu", }, + { .compatible = "qcom,sm8150-dpu", }, + { .compatible = "qcom,sm8250-dpu", }, {} }; MODULE_DEVICE_TABLE(of, dpu_dt_match); diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c index 94525ac76d4e..928f13d4bfbc 100644 --- a/drivers/gpu/drm/msm/msm_drv.c +++ b/drivers/gpu/drm/msm/msm_drv.c @@ -1185,9 +1185,7 @@ static int add_display_components(struct device *dev, * Populate the children devices, find the MDP5/DPU node, and then add * the interfaces to our components list. */ - if (of_device_is_compatible(dev->of_node, "qcom,mdss") || - of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") || - of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) { + if (!of_device_is_compatible(dev->of_node, "qcom,mdp4")) { ret = of_platform_populate(dev->of_node, NULL, NULL, dev); if (ret) { DRM_DEV_ERROR(dev, "failed to populate children devices\n"); @@ -1320,6 +1318,8 @@ static const struct of_device_id dt_match[] = { { .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 }, { .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU }, { .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU }, + { .compatible = "qcom,sm8150-mdss", .data = (void *)KMS_DPU }, + { .compatible = "qcom,sm8250-mdss", .data = (void *)KMS_DPU }, {} }; MODULE_DEVICE_TABLE(of, dt_match);
The driver already has support for sm8150/sm8250, but the compatibles were never added. Also inverse the non-mdp4 condition in add_display_components() to avoid having to check every new compatible in the condition. Signed-off-by: Jonathan Marek <jonathan@marek.ca> --- Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++-- drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 2 ++ drivers/gpu/drm/msm/msm_drv.c | 6 +++--- 3 files changed, 7 insertions(+), 5 deletions(-)