@@ -44,6 +44,7 @@
#include "sun8i-a33.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "BananaPi M2 Magic";
@@ -55,12 +56,21 @@ aliases {
i2c2 = &i2c2;
serial0 = &uart0;
serial1 = &uart1;
+ mmc0 = &mmc0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <1 2 4 8 16 32 64 128 255>;
+ default-brightness-level = <8>;
+ enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PL4 */
+ };
+
leds {
compatible = "gpio-leds";
@@ -81,6 +91,18 @@ led-2 {
};
};
+ panel {
+ compatible = "bananapi,s070wv20-ct16";
+ enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PB7 */
+ backlight = <&backlight>;
+
+ port {
+ panel_out_bridge: endpoint {
+ remote-endpoint = <&bridge_out_panel>;
+ };
+ };
+ };
+
reg_vcc5v0: vcc5v0 {
compatible = "regulator-fixed";
regulator-name = "vcc5v0";
@@ -122,6 +144,59 @@ &dai {
status = "okay";
};
+&de {
+ status = "okay";
+};
+
+&dphy {
+ status = "okay";
+};
+
+&dsi {
+ vcc-dsi-supply = <®_dcdc1>; /* VCC-DSI */
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dsi_out: port@0 {
+ reg = <0>;
+
+ dsi_out_bridge: endpoint {
+ remote-endpoint = <&bridge_out_dsi>;
+ };
+ };
+ };
+
+ bridge@0 {
+ compatible = "chipone,icn6211";
+ reg = <0>;
+ enable-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bridge_in: port@0 {
+ reg = <0>;
+
+ bridge_out_dsi: endpoint {
+ remote-endpoint = <&dsi_out_bridge>;
+ };
+ };
+
+ bridge_out: port@1 {
+ reg = <1>;
+
+ bridge_out_panel: endpoint {
+ remote-endpoint = <&panel_out_bridge>;
+ };
+ };
+ };
+ };
+};
+
&ehci0 {
status = "okay";
};
@@ -157,6 +232,12 @@ &ohci0 {
status = "okay";
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
&r_rsb {
status = "okay";
@@ -269,6 +350,10 @@ &sound {
status = "okay";
};
+&tcon0 {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
This patch add support for Bananapi S070WV20-CT16 panel to BPI-M2M board. Bananapi S070WV20-CT16 is a pure RGB output panel with ICN6211 DSI/RGB converter bridge, so enable bridge along with associated panel. DSI panel connected via board DSI port with, - DCDC1 as VCC-DSI supply - PL5 gpio for bridge enable gpio pin - PB7 gpio for lcd enable gpio pin - PL4 gpio for backlight enable pin Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- Changes for v4: - replace reset with enable-gpios Changes for v3: - none arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 85 ++++++++++++++++++++ 1 file changed, 85 insertions(+)